Abstract: Effective cooling of electronic equipment has emerged
as a challenging and constraining problem of the new century. In the
present work the feasibility and effectiveness of jet impingement
cooling on electronics were investigated numerically and
experimentally. Studies have been conducted to see the effect of the
geometrical parameters such as jet diameter (D), jet to target
spacing (Z) and ratio of jet spacing to jet diameter (Z/D) on the heat
transfer characteristics. The values of Reynolds numbers considered
are in the range 7000 to 42000. The results obtained from the
numerical studies are validated by conducting experiments. From the
studies it is found that the optimum value of Z/D ratio is 5. For a
given Reynolds number, the Nusselt number increases by about 28%
if the diameter of the nozzle is increased from 1mm to 2mm.
Correlations are proposed for Nusselt number in terms of Reynolds
number and these are valid for air as the cooling medium.
Abstract: In this study a two dimensional axisymmetric, steady state and incompressible laminar flow in a rotating single disk is numerically investigated. The finite volume method is used for solving the momentum equations. The numerical model and results
are validated by comparing it to previously reported experimental data for velocities, angles and moment coefficients. It is
demonstrated that increasing the axial distance increases the value of axial velocity and vice versa for tangential and total velocities. However, the maximum value of nondimensional radial velocity
occurs near the disk wall. It is also found that with increase rotational Reynolds number, moment coefficient decreases.
Abstract: PCMs have always been viewed as a suitable
candidate for off peak thermal storage, particularly for refrigeration
systems, due to the high latent energy densities of these materials.
However, due to the need to have them encapsulated within a
container this density is reduced. Furthermore, PCMs have a low
thermal conductivity which reduces the useful amount of energy
which can be stored. To consider these factors, the true energy
storage density of a PCM system was proposed and optimised for
PCMs encapsulated in slabs. Using a validated numerical model of
the system, a parametric study was undertaken to investigate the
impact of the slab thickness, gap between slabs and the mass flow
rate. The study showed that, when optimised, a PCM system can
deliver a true energy storage density between 53% and 83% of the
latent energy density of the PCM.
Abstract: Process-oriented software development is a new
software development paradigm in which software design is modeled
by a business process which is in turn translated into a process
execution language for execution. The building blocks of this
paradigm are software units that are composed together to work
according to the flow of the business process. This new paradigm
still exhibits the characteristic of the applications built with the
traditional software component technology. This paper discusses an
approach to apply a traditional technique for software component
fabrication to the design of process-oriented software units, called
process components. These process components result from
decomposing a business process of a particular application domain
into subprocesses, and these process components can be reused to
design the business processes of other application domains. The
decomposition considers five managerial goals, namely cost
effectiveness, ease of assembly, customization, reusability, and
maintainability. The paper presents how to design or decompose
process components from a business process model and measure
some technical features of the design that would affect the
managerial goals. A comparison between the measurement values
from different designs can tell which process component design is
more appropriate for the managerial goals that have been set. The
proposed approach can be applied in Web Services environment
which accommodates process-oriented software development.
Abstract: This paper introduces an approach to construct a set of criteria for evaluating alternative options. Content analysis was used to collet criterion elements. Then the elements were classified and organized yielding to hierarchic structure. The reliability of the constructed criteria was evaluated in an experiment. Finally the criteria were used to evaluate alternative options indecision-making.
Abstract: In the present paper, disc loaded interaction structure
for potential application in wideband Gyro-TWT amplifier has been
analyzed, taking all the space and modal harmonics into
consideration, for the eigenwave solutions. The analysis has been
restricted to azimuthally symmetric TE0,n mode. Dispersion
characteristics have been plotted by varying the structure parameters
and have been validated against HFSS simulation results. The
variation of eigenvalue with respect to different structure parameters
has also been presented. It has been observed that disc periodicity
plays very important role for wideband operation of disc-loaded
Gyro-TWT.
Abstract: Synthesis gas manufacturing by steam reforming of hydrocarbons is an important industrial process. High endothermic nature of the process makes it one of the most cost and heat intensive processes. In the present work, composite effect of different inert gases on synthesis gas yield, feed gas conversion and temperature distribution along the reactor length has been studied using a heterogeneous model. Mathematical model was developed as a first stage and validated against the existing process models. With the addition of inert gases, a higher yield of synthesis gas is observed. Simultaneously the rector outlet temperature drops to as low as 810 K. It was found that Xenon gives the highest yield and conversion while Helium gives the lowest temperature. Using Xenon inert gas 20 percent reduction in outlet temperature was observed compared to traditional case.
Abstract: A model predictive controller based on recursive learning is proposed. In this SISO adaptive controller, a model is automatically updated using simple recursive equations. The identified models are then stored in the memory to be re-used in the future. The decision for model update is taken based on a new control performance index. The new controller allows the use of simple linear model predictive controllers in the control of nonlinear time varying processes.
Abstract: The major objective of this paper is to introduce a new method to select genes from DNA microarray data. As criterion to select genes we suggest to measure the local changes in the correlation graph of each gene and to select those genes whose local changes are largest. More precisely, we calculate the correlation networks from DNA microarray data of cervical cancer whereas each network represents a tissue of a certain tumor stage and each node in the network represents a gene. From these networks we extract one tree for each gene by a local decomposition of the correlation network. The interpretation of a tree is that it represents the n-nearest neighbor genes on the n-th level of a tree, measured by the Dijkstra distance, and, hence, gives the local embedding of a gene within the correlation network. For the obtained trees we measure the pairwise similarity between trees rooted by the same gene from normal to cancerous tissues. This evaluates the modification of the tree topology due to tumor progression. Finally, we rank the obtained similarity values from all tissue comparisons and select the top ranked genes. For these genes the local neighborhood in the correlation networks changes most between normal and cancerous tissues. As a result we find that the top ranked genes are candidates suspected to be involved in tumor growth. This indicates that our method captures essential information from the underlying DNA microarray data of cervical cancer.
Abstract: This paper presents the experimental results of silicone rubber polymer insulators for 22 kV systems under salt water dip wheel test based on IEC 62217. Straight shed silicone rubber polymer insulators having leakage distance 685 mm were tested continuously 30,000 cycles. One test cycle includes 4 positions, energized, de-energized, salt water dip and deenergized, respectively. For one test cycle, each test specimen remains stationary for about 40 second in each position and takes 8 second for rotate to next position. By visual observation, sever surface erosion was observed on the trunk near the energized end of tested specimen. Puncture was observed on the upper shed near the energized end. In addition, decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Furthermore, chemical analysis by ATR-FTIR was conducted in order to elucidate the chemical change of tested specimens comparing with new specimen.
Abstract: Using neural network we try to model the unknown function f for given input-output data pairs. The connection strength of each neuron is updated through learning. Repeated simulations of crisp neural network produce different values of weight factors that are directly affected by the change of different parameters. We propose the idea that for each neuron in the network, we can obtain quasi-fuzzy weight sets (QFWS) using repeated simulation of the crisp neural network. Such type of fuzzy weight functions may be applied where we have multivariate crisp input that needs to be adjusted after iterative learning, like claim amount distribution analysis. As real data is subjected to noise and uncertainty, therefore, QFWS may be helpful in the simplification of such complex problems. Secondly, these QFWS provide good initial solution for training of fuzzy neural networks with reduced computational complexity.
Abstract: The hydrolysis kinetics of polycrystalline lithium hydride (LiH) in argon at various low humidities was measured by gravimetry and Raman spectroscopy with ambient water concentration ranging from 200 to 1200 ppm. The results showed that LiH hydrolysis curve revealed a paralinear shape, which was attributed to two different reaction stages that forming different products as explained by the 'Layer Diffusion Control' model. Based on the model, a novel two-stage rate equation for LiH hydrolysis reactions was developed and used to fit the experimental data for determination of Li2O steady thickness Hs and the ultimate hydrolysis rate vs. The fitted data presented a rise of Hs as ambient water concentration cw increased. However, in spite of the negative effect imposed by Hs increasing, the upward trend of vs remained, which implied that water concentration, rather than Li2O thickness, played a predominant role in LiH hydrolysis kinetics. In addition, the proportional relationship between vsHs and cw predicted by rate equation and confirmed by gravimetric data validated the model in such conditions.
Abstract: The purpose of this paper is to present teacher candidates- beliefs about technology integration in their field of study, which is classroom teaching in this case. The study was conducted among the first year students in college of education in Turkey. This study is based on both quantitative and qualitative data. For the quantitative data- Likert scale was used and for the qualitative data pattern matching was employed. The primary findings showed that students defined educational technology as technologies that improve learning with their visual, easily accessible, and productive features. They also believe these technologies could affect their future students- learning positively.
Abstract: The objective of the presented work is to implement the Kalman Filter into an application that reduces the influence of the environmental changes over the robot expected to navigate over a terrain of varying friction properties. The Discrete Kalman Filter is used to estimate the robot position, project the estimated current state ahead at time through time update and adjust the projected estimated state by an actual measurement at that time via the measurement update using the data coming from the infrared sensors, ultrasonic sensors and the visual sensor respectively. The navigation test has been performed in a real world environment and has been found to be robust.
Abstract: The prevalence of non organic constipation differs
from country to country and the reliability of the estimate rates is
uncertain. Moreover, the clinical relevance of subdividing the
heterogeneous functional constipation disorders into pre-defined
subgroups is largely unknown.. Aim: to estimate the prevalence of
constipation in a population-based sample and determine whether
clinical subgroups can be identified. An age and gender stratified
sample population from 5 Italian cities was evaluated using a
previously validated questionnaire. Data mining by cluster analysis
was used to determine constipation subgroups. Results: 1,500
complete interviews were obtained from 2,083 contacted households
(72%). Self-reported constipation correlated poorly with symptombased
constipation found in 496 subjects (33.1%). Cluster analysis
identified four constipation subgroups which correlated to subgroups
identified according to pre-defined symptom criteria. Significant
differences in socio-demographics and lifestyle were observed
among subgroups.
Abstract: In very narrow pathways, the speed of sound propagation and the phase of sound waves change due to the air viscosity. We have developed a new finite element method (FEM) that includes the effects of air viscosity for modeling a narrow sound pathway. This method is developed as an extension of the existing FEM for porous sound-absorbing materials. The numerical calculation results for several three-dimensional slit models using the proposed FEM are validated against existing calculation methods.
Abstract: This paper presents a new method of fault detection and isolation (FDI) for polymer electrolyte membrane (PEM) fuel cell (FC) dynamic systems under an open-loop scheme. This method uses a radial basis function (RBF) neural network to perform fault identification, classification and isolation. The novelty is that the RBF model of independent mode is used to predict the future outputs of the FC stack. One actuator fault, one component fault and three sensor faults have been introduced to the PEMFC systems experience faults between -7% to +10% of fault size in real-time operation. To validate the results, a benchmark model developed by Michigan University is used in the simulation to investigate the effect of these five faults. The developed independent RBF model is tested on MATLAB R2009a/Simulink environment. The simulation results confirm the effectiveness of the proposed method for FDI under an open-loop condition. By using this method, the RBF networks able to detect and isolate all five faults accordingly and accurately.
Abstract: In recent years the large scale use of the power electronic equipment has led to an increase of harmonics in the power system. The harmonics results into a poor power quality and have great adverse economical impact on the utilities and customers. Current harmonics are one of the most common power quality problems and are usually resolved by using shunt active filter (SHAF). The main objective of this work is to develop PI and Fuzzy logic controllers (FLC) to analyze the performance of Shunt Active Filter for mitigating current harmonics under balanced and unbalanced sinusoidal source voltage conditions for normal load and increased load. When the supply voltages are ideal (balanced), both PI and FLC are converging to the same compensation characteristics. However, the supply voltages are non-ideal (unbalanced), FLC offers outstanding results. Simulation results validate the superiority of FLC with triangular membership function over the PI controller.
Abstract: The paper presents a one-dimensional transient
mathematical model of thermal oil-water two-phase emulsion flows
in pipes. The set of the mass, momentum and enthalpy conservation
equations for the continuous fluid and droplet phases are solved. Two
friction correlations for the continuous fluid phase to wall friction are
accounted for in the model and tested. The aerodynamic drag force
between the continuous fluid phase and droplets is modeled, too. The
density and viscosity of both phases are assumed to be constant due
to adiabatic experimental conditions. The proposed mathematical
model is validated on the experimental measurements of oil-water
emulsion flows in horizontal pipe [1,2]. Numerical analysis on
single- and two-phase oil-water flows in a pipe is presented in the
paper. The continuous oil flow having water droplets is simulated.
Predictions, which are performed by using the presented model, show
excellent agreement with the experimental data if the water fraction is
equal or less than 10%. Disagreement between simulations and
measurements is increased if the water fraction is larger than 10%.
Abstract: This study considers the problem of determining
operation and maintenance schedules for a containership equipped
with components during its sailing according to a pre-determined
navigation schedule. The operation schedule, which specifies work
time of each component, determines the due-date of each maintenance
activity, and the maintenance schedule specifies the actual start
time of each maintenance activity. The main constraints are component
requirements, workforce availability, working time limitation,
and inter-maintenance time. To represent the problem mathematically,
a mixed integer programming model is developed. Then,
due to the problem complexity, we suggest a heuristic for the objective
of minimizing the sum of earliness and tardiness between the
due-date and the starting time of each maintenance activity. Computational
experiments were done on various test instances and the
results are reported.