Abstract: A numerical study is presented on convective heat transfer in enclosures. The results are addressed to automotive headlights containing new-age light sources like Light Emitting Diodes (LED). The heat transfer from the heat source (LED) to the enclosure walls is investigated for mixed convection as interaction of the forced convection flow from an inlet and an outlet port and the natural convection at the heat source. Unlike existing studies, inlet and outlet port are thermally coupled and do not serve to remove hot fluid. The input power of the heat source is expressed by the Rayleigh number. The internal position of the heat source, the aspect ratio of the enclosure, and the inclination angle of one wall are varied. The results are given in terms of the global Nusselt number and the enclosure Nusselt number that characterize the heat transfer from the source and from the interior fluid to the enclosure walls, respectively. It is found that the heat transfer from the source to the fluid can be maximized if the source is placed in the main stream from the inlet to the outlet port. In this case, the Reynolds number and heat source position have the major impact on the heat transfer. A disadvantageous position has been found where natural and forced convection compete each other. The overall heat transfer from the source to the wall increases with increasing Reynolds number as well as with increasing aspect ratio and decreasing inclination angle. The heat transfer from the interior fluid to the enclosure wall increases upon decreasing the aspect ratio and increasing the inclination angle. This counteracting behaviour is caused by the variation of the area of the enclosure wall. All mixed convection results are compared to the natural convection limit.
Abstract: This paper presents a new method of fault detection and isolation (FDI) for polymer electrolyte membrane (PEM) fuel cell (FC) dynamic systems under an open-loop scheme. This method uses a radial basis function (RBF) neural network to perform fault identification, classification and isolation. The novelty is that the RBF model of independent mode is used to predict the future outputs of the FC stack. One actuator fault, one component fault and three sensor faults have been introduced to the PEMFC systems experience faults between -7% to +10% of fault size in real-time operation. To validate the results, a benchmark model developed by Michigan University is used in the simulation to investigate the effect of these five faults. The developed independent RBF model is tested on MATLAB R2009a/Simulink environment. The simulation results confirm the effectiveness of the proposed method for FDI under an open-loop condition. By using this method, the RBF networks able to detect and isolate all five faults accordingly and accurately.
Abstract: In two studies we tested the hypothesis that the
appropriate linguistic formulation of a deontic rule – i.e. the
formulation which clarifies the monadic nature of deontic operators
- should produce more correct responses than the conditional
formulation in Wason selection task. We tested this assumption by
presenting a prescription rule and a prohibition rule in conditional
vs. proper deontic formulation. We contrasted this hypothesis with
two other hypotheses derived from social contract theory and
relevance theory. According to the first theory, a deontic rule
expressed in terms of cost-benefit should elicit a cheater detection
module, sensible to mental states attributions and thus able to
discriminate intentional rule violations from accidental rule
violations. We tested this prevision by distinguishing the two types
of violations. According to relevance theory, performance in
selection task should improve by increasing cognitive effect and
decreasing cognitive effort. We tested this prevision by focusing
experimental instructions on the rule vs. the action covered by the
rule. In study 1, in which 480 undergraduates participated, we
tested these predictions through a 2 x 2 x 2 x 2 (type of the rule x
rule formulation x type of violation x experimental instructions)
between-subjects design. In study 2 – carried out by means of a 2 x
2 (rule formulation x type of violation) between-subjects design -
we retested the hypothesis of rule formulation vs. the cheaterdetection
hypothesis through a new version of selection task in
which intentional vs. accidental rule violations were better
discriminated. 240 undergraduates participated in this study.
Results corroborate our hypothesis and challenge the contrasting
assumptions. However, they show that the conditional formulation
of deontic rules produces a lower performance than what is
reported in literature.
Abstract: In this paper we define generalized differential operators from some well-known operators on the class A of analytic functions in the unit disk U = {z ∈ C : |z| < 1}. New classes containing these operators are investigated. Also univalence of integral operator is considered.
Abstract: In this paper, we introduce a new method for elliptical
object identification. The proposed method adopts a hybrid scheme
which consists of Eigen values of covariance matrices, Circular
Hough transform and Bresenham-s raster scan algorithms. In this
approach we use the fact that the large Eigen values and small Eigen
values of covariance matrices are associated with the major and minor
axial lengths of the ellipse. The centre location of the ellipse can be
identified using circular Hough transform (CHT). Sparse matrix
technique is used to perform CHT. Since sparse matrices squeeze zero
elements and contain a small number of nonzero elements they
provide an advantage of matrix storage space and computational time.
Neighborhood suppression scheme is used to find the valid Hough
peaks. The accurate position of circumference pixels is identified
using raster scan algorithm which uses the geometrical symmetry
property. This method does not require the evaluation of tangents or
curvature of edge contours, which are generally very sensitive to
noise working conditions. The proposed method has the advantages of
small storage, high speed and accuracy in identifying the feature. The
new method has been tested on both synthetic and real images.
Several experiments have been conducted on various images with
considerable background noise to reveal the efficacy and robustness.
Experimental results about the accuracy of the proposed method,
comparisons with Hough transform and its variants and other
tangential based methods are reported.
Abstract: Experiments with pumpkin-rowanberry marmalade
candies were carried out at the Faculty of Food Technology of the
Latvia University of Agriculture. The objective of this investigation
was to evaluate the quality changes of pumpkin-rowanberry
marmalade candies packed in different packaging materials during
the storage of 15 weeks, and to find the most suitable packaging
material for prolongation of low sugar marmalade candies shelf-life.
An active packaging in combination with modified atmosphere
(MAP, CO2 100%) was examined and compared with traditional
packaging in air ambiance. Polymer Multibarrier 60 and paper bags
were used. Influence of iron based oxygen absorber in sachets of 500
cc obtained from Mitsubishi Gas Chemical Europe Ageless® on the
marmalade candies’ quality was tested during shelf life. Samples of
80±5 g were packaged in polymer pouches (110 mm x 110 mm),
hermetically sealed by MULTIVAC C300 vacuum chamber machine,
and stored in a room temperature +21±0.5 °C. The physiochemical
properties –moisture content, hardness, aw, pH, changes of
atmosphere content (CO2 and O2), ascorbic acid, total carotenoids,
total phenols in headspace of packs, and microbial conditions were
analysed before packaging and in the 1st, 3rd , 5th, 8th, 11th and 15th
weeks of storage.
Abstract: Nowadays, the earth is countered with serious problem
of air pollution. This problem has been started from the industrial
revolution and has been faster in recent years, so that leads the earth
to ecological and environmental disaster. One of its results is the
global warming problem and its related increase in global
temperature. The most important factors in air pollution especially in
urban environments are Automobiles and residential buildings that are
the biggest consumers of the fossil energies, so that if the residential
buildings as a big part of the consumers of such energies reduce their
consumption rate, the air pollution will be decreased. Since
Metropolises are the main centers of air pollution in the world,
assessment and analysis of efficient strategies in decreasing air
pollution in such cities, can lead to the desirable and suitable results
and can solve the problem at least in critical level. Tabriz city is one
of the most important metropolises in North west of Iran that about
two million people are living there. for its situation in cold dry
climate, has a high rate of fossil energies consumption that make air
pollution in its urban environment. These two factors, being both
metropolis and in cold dry climate, make this article try to analyze the
strategies of climatic design in old districts of the city and use them in
new districts of the future. These strategies can be used in this city
and other similar cities and pave the way to reduce energy
consumption and related air pollution to save whole world.
Abstract: Nowadays, access to sustainable development in cities is assumed as one of the most important goals of urban managers. In the meanwhile, neighborhood as the smallest unit of urban spatial organization has a substantial effect on urban sustainability. Hence, attention to and focus on this subject is highly important in urban development plans. The objective of this study is evaluation of the status of Jahanshahr Neighborhood in Karaj city based on sustainable neighborhood development indicators. This research has been applied based on documentary method and field surveys. Also, evaluating of Jahanshahr Neighborhood of Karaj shows that it has a high level in sustainability in physical and economical dimension while a low level in cultural and social dimension. For this purpose, this neighborhood as a semi-sustainable neighborhood must take measures for development of collective spaces and efficiency of utilizing the public neighborhood spaces via collaboration of citizens and officials.
Abstract: Speed sensorless systems are intensively studied during recent years; this is mainly due to their economical benefit and fragility of mechanical sensors and also the difficulty of installing this type of sensor in many applications. These systems suffer from instability problems and sensitivity to parameter mismatch at low speed operation. In this paper an analysis of adaptive observer stability with stator resistance estimation is given.
Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: One of the main processes of supply chain
management is supplier selection process which its accurate
implementation can dramatically increase company competitiveness.
In presented article model developed based on the features of
second tiers suppliers and four scenarios are predicted in order to
help the decision maker (DM) in making up his/her mind. In addition
two tiers of suppliers have been considered as a chain of suppliers.
Then the proposed approach is solved by a method combined of
concepts of fuzzy set theory (FST) and linear programming (LP)
which has been nourished by real data extracted from an engineering
design and supplying parts company. At the end results reveal the
high importance of considering second tier suppliers features as
criteria for selecting the best supplier.
Abstract: This paper proposes a simple model of economic geography within the Dixit-Stiglitz-Iceberg framework that may be used to analyze migration patterns among three cities. The cost–benefit tradeoffs affecting incentives for three types of migration, including echelon migration, are discussed. This paper develops a tractable, heterogeneous-agent, general equilibrium model, where agents share constant human capital, and explores the relationship between the benefits of echelon migration and gross human capital. Using Chinese numerical solutions, we study the manifestation of echelon migration and how it responds to changes in transportation cost and elasticity of substitution. Numerical results demonstrate that (i) there are positive relationships between a migration-s benefit-and-wage ratio, (ii) there are positive relationships between gross human capital ratios and wage ratios as to origin and destination, and (iii) we identify 13 varieties of human capital convergence among cities. In particular, this model predicts population shock resulting from the processes of migration choice and echelon migration.
Abstract: The present work demonstrates the design and simulation of a fuzzy control of an air conditioning system at different pressures. The first order Sugeno fuzzy inference system is utilized to model the system and create the controller. In addition, an estimation of the heat transfer rate and water mass flow rate injection into or withdraw from the air conditioning system is determined by the fuzzy IF-THEN rules. The approach starts by generating the input/output data. Then, the subtractive clustering algorithm along with least square estimation (LSE) generates the fuzzy rules that describe the relationship between input/output data. The fuzzy rules are tuned by Adaptive Neuro-Fuzzy Inference System (ANFIS). The results show that when the pressure increases the amount of water flow rate and heat transfer rate decrease within the lower ranges of inlet dry bulb temperatures. On the other hand, and as pressure increases the amount of water flow rate and heat transfer rate increases within the higher ranges of inlet dry bulb temperatures. The inflection in the pressure effect trend occurs at lower temperatures as the inlet air humidity increases.
Abstract: Data stream analysis is the process of computing
various summaries and derived values from large amounts of data
which are continuously generated at a rapid rate. The nature of a
stream does not allow a revisit on each data element. Furthermore,
data processing must be fast to produce timely analysis results. These
requirements impose constraints on the design of the algorithms to
balance correctness against timely responses. Several techniques
have been proposed over the past few years to address these
challenges. These techniques can be categorized as either dataoriented
or task-oriented. The data-oriented approach analyzes a
subset of data or a smaller transformed representation, whereas taskoriented
scheme solves the problem directly via approximation
techniques. We propose a hybrid approach to tackle the data stream
analysis problem. The data stream has been both statistically
transformed to a smaller size and computationally approximated its
characteristics. We adopt a Monte Carlo method in the approximation
step. The data reduction has been performed horizontally and
vertically through our EMR sampling method. The proposed method
is analyzed by a series of experiments. We apply our algorithm on
clustering and classification tasks to evaluate the utility of our
approach.
Abstract: Sorting appears the most attention among all computational tasks over the past years because sorted data is at the heart of many computations. Sorting is of additional importance to parallel computing because of its close relation to the task of routing data among processes, which is an essential part of many parallel algorithms. Many parallel sorting algorithms have been investigated for a variety of parallel computer architectures. In this paper, three parallel sorting algorithms have been implemented and compared in terms of their overall execution time. The algorithms implemented are the odd-even transposition sort, parallel merge sort and parallel rank sort. Cluster of Workstations or Windows Compute Cluster has been used to compare the algorithms implemented. The C# programming language is used to develop the sorting algorithms. The MPI (Message Passing Interface) library has been selected to establish the communication and synchronization between processors. The time complexity for each parallel sorting algorithm will also be mentioned and analyzed.
Abstract: A Rotary Disc Contactor with inner diameter of
9.1cm and maximum operating height of 40cm has been used to
investigate break up phenomenon. Water-Toluene, Water as
continuous phase and Toluene as dispersed phase, was selected as
chemical system in the experiments. The mentioned chemical system
has high interfacial tension so it was possible to form big drops
which permit accurate investigation on break up phenomenon as well
as the first and second critical rotor speeds.
In this study, Break up phenomenon has been studied as a function
of mother drop size, rotor speed and continuous phase height. Further
more; the effects of mother drop size and continuous phase height on
the first and second critical rotor speeds were investigated. Finally,
two modified correlations were proposed to estimate the first and
second critical speeds.
Abstract: Over the past years, the EMCCD has had a profound
influence on photon starved imaging applications relying on its unique
multiplication register based on the impact ionization effect in the
silicon. High signal-to-noise ratio (SNR) means high image quality.
Thus, SNR improvement is important for the EMCCD. This work
analyzes the SNR performance of an EMCCD with gain off and on. In
each mode, simplified SNR models are established for different
integration times. The SNR curves are divided into readout noise (or
CIC) region and shot noise region by integration time. Theoretical
SNR values comparing long frame integration and frame adding in
each region are presented and discussed to figure out which method is
more effective. In order to further improve the SNR performance,
pixel binning is introduced into the EMCCD. The results show that
pixel binning does obviously improve the SNR performance, but at the
expensive of the spatial resolution.
Abstract: The efficiency of chitosan beads processed from 4
marine animal shells; white leg shrimp (Litopenaeus vannamei), mud
crab (Scylla sp.), horseshoe crab (Carcinoscorpius rotundicauda),
and cuttlefish bone (Sepia sp.), for the adsorption experiments of
ammonia and formaldehyde were investigated. The porosities of
chitosan from the shells looked like beads were distinctly examined
under SEM. The original pores of those shells on the surface areas
compose of evenly fine pores. The shell beads of cuttlefish bone and
horseshoe crab show the larger probably even porosity, while on
those white leg shrimp and mud crab contain various large and fine
pores. The best adsorption at pH 9 in 18 mg/l ammonia at 2 hours
yield on cuttlefish bone, horseshoe crab, mud crab and white leg
shrimp with the average percent of 59.12, 51.45, 45.66 and 43.52,
respectively. Within 30 minutes the formaldehyde absorbers (at pH 5
in 8 μg/ml) revealed 46.27, 26.56, and 18.04 percent capacities in
cuttlefish bone, mud crab and white leg shrimp beads; while 22.44
percent in the horseshoe crab at pH 7. The adsorption capacities and
the amounts of beads showed a positive correlation. The adsorption
capacity relationship between pH and the gas concentrations were
affected by these qualities of chitosan beads.
Abstract: The regional innovative competitiveness is an integrating characteristic of the innovative sphere of the region. It depends on a big variety of different parameters connected with all kinds of economic entities- activities. But management parameters shouldn't be irregular, so in order to avoid it, an institutional system should be formed. This system should carry out strategic management of factors having the greatest influence on the region's innovative development. This article is devoted to different aspects of organization of the region's development institutional mechanism, which is based on management of regional innovative competitiveness parameters. The base of the analysis is innovatively-active Russian regions which were compared according to the level of the innovative competitiveness. After that the most important parameters of successful innovative development of the region were revealed with the help of the correlation-regression analysis. The results of the research could be used for investigation of the region's innovative policy.
Abstract: The experiment was conducted to evaluate
digestibility quantities of protein in Canola Meals (CMs) between
caecectomised and intact adult Rhode Island Red (RIR) cockerels
with using conventional addition method (CAM) for 7 d: a 4-d
adaptation and a 3-d experiment period on the basis of a completely
randomized design with 4 replicates. Results indicated that
caecectomy decreased (P