Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: The disposal and the treatment of sewage sludge is an
expensive and environmentally complex problem. In this work, a
lipopeptide biosurfactant extracted from corn steep liquor was used
as ecofriendly and cost-competitive alternative for the mobilization
and bioremediation of fluorene in sewage sludge. Results have
demonstrated that this biosurfactant has the capability to mobilize
fluorene to the aqueous phase, reducing the amount of fluorene in the
sewage sludge from 484.4 mg/Kg up to 413.7 mg/Kg and 196.0
mg/Kg after 1 and 27 days respectively. Furthermore, once the
fluorene was extracted the lipopeptide biosurfactant contained in the
aqueous phase allowed the biodegradation, up to 40.5% of the initial
concentration of this polycyclic aromatic hydrocarbon.
Abstract: Work presented is interested in the characterization of
the quasistatic mechanical properties and in fatigue of a composite
laminated in jute/epoxy. The natural fibers offer promising prospects
thanks to their interesting specific properties, because of their low
density, but also with their bio-deterioration. Several scientific
studies highlighted the good mechanical resistance of the vegetable
fiber composites reinforced, even after several recycling. Because of
the environmental standards that become increasingly severe, one
attends the emergence of eco-materials at the base of natural fibers
such as flax, bamboo, hemp, sisal, jute. The fatigue tests on
elementary vegetable fibers show an increase of about 60% of the
rigidity of elementary fibers of hemp subjected to cyclic loadings. In
this study, the test-tubes manufactured by the method infusion have
sequences of stacking of 0/90° and ± 45° for the shearing and tensile
tests. The quasistatic tests reveal a variability of the mechanical
properties of about 8%. The tensile fatigue tests were carried out for
levels of constraints equivalent to half of the ultimate values of the
composite. Once the fatigue tests carried out for well-defined values
of cycles, a series of static tests of traction type highlights the
influence of the number of cycles on the quasi-static mechanical
behavior of the laminate jute/epoxy.
Abstract: Standard Gibbs energy of formation ΔGfor(298.15) of
lanthanide-iron double oxides of garnet-type crystal structure
R3Fe5O12 - RIG (R – are rare earth ions) from initial oxides are
evaluated. The calculation is based on the data of standard entropies
S298.15 and standard enthalpies ΔH298.15 of formation of compounds
which are involved in the process of garnets synthesis. Gibbs energy
of formation is presented as temperature function ΔGfor(T) for the
range 300-1600K. The necessary starting thermodynamic data were
obtained from calorimetric study of heat capacity – temperature
functions and by using the semi-empirical method for calculation of
ΔH298.15 of formation. Thermodynamic functions for standard
temperature – enthalpy, entropy and Gibbs energy - are
recommended as reference data for technological evaluations.
Through the structural series of rare earth-iron garnets the correlation
between thermodynamic properties and characteristics of lanthanide
ions are elucidated.
Abstract: Low Temperature Matrix Isolation - Electron
Paramagnetic Resonance (LTMI-EPR) Spectroscopy was utilized to
identify the species of iron oxide nanoparticles generated during the
oxidative pyrolysis of 1-methylnaphthalene (1-MN). The otherwise
gas-phase reactions of 1--MN were impacted by a polypropylenimine
tetra-hexacontaamine dendrimer complexed with iron (III) nitrate
nonahydrate diluted in air under atmospheric conditions. The EPR
fine structure of Fe (III)2O3 nanoparticles clusters, characterized by gfactors
of 2.00, 2.28, 3.76 and 4.37 were detected on a cold finger
maintained at 77 K after accumulation over a multitude of
experiments. Additionally, a high valence Fe (IV) paramagnetic
intermediate and superoxide anion-radicals, O2•- adsorbed on
nanoparticle surfaces in the form of Fe (IV) --- O2•- were detected
from the quenching area of Zone 1 in the gas-phase.
Abstract: Determination of genetic variation is useful for plant
breeding and hence production of more efficient plant species under
different conditions, like drought stress. In this study a sample of 28
recombinant inbred lines (RILs) of wheat developed from the cross of
Norstar and Zagross varieties, together with their parents, were
evaluated for two years (2010-2012) under normal and water stress
conditions using split plot design with three replications. Main plots
included two irrigation treatments of 70 and 140 mm evaporation
from Class A pan and sub-plots consisted of 30 genotypes. The effect
of genotypes and interaction of genotypes with years and water
regimes were significant for all characters. Significant genotypic
effect implies the existence of genetic variation among the lines
under study. Heritability estimates were high for 1000 grain weight
(0.87). Biomass and grain yield showed the lowest heritability values
(0.42 and 0.50, respectively). Highest genotypic and phenotypic
coefficients of variation (GCV and PCV) belonged to harvest index.
Moderate genetic advance for most of the traits suggested the
feasibility of selection among the RILs under investigation. Some
RILs were higher yielding than either parent at both environments.
Abstract: In this research, a questionnaire survey was conducted
to measure nap, drowsiness and fatigue of drivers who work for long
shifts, to discuss about the work environment and health conditions for
taxi and bus drivers who work at night-time. The questionnaire sheet
used for this research was organized into the following categories:
tension/tiredness, drowsiness while driving, and the nap situation
during night-time work. The number of taxi drivers was 127 and the
number of bus drivers was 40. Concerning the results of a comparison
of nap hours of taxi and bus drivers, the taxi drivers’ nap hours are
overwhelmingly shorter, and also the frequency of drivers who
experience drowsiness is higher. The burden on bus drivers does not
change because of the system of a two-driver rotation shift. In
particular, the working environment of the taxi driver may lead to
greater fatigue accumulation than the bus driver’s environment.
Abstract: New environmental regulations and the increasing
market preference for companies that respect the ecosystem had
encouraged the industry to look after new treatments for its effluents.
The sugar industry, one of the largest emitter of environmental
pollutants, follows this tendency. Membrane technology is
convenient for separation of suspended solids, colloids and high
molecular weight materials that are present in a wastewater from
sugar industry. The idea is to microfilter the wastewater, where the
permeate passes through the membrane and becomes available for
recycle and re-use in the sugar manufacturing process. For
microfiltration of this effluent a tubular ceramic membrane was used
with a pore size of 200 nm at transmembrane pressure in range of 1–3
bars and in range of flow rate of 50–150 l/h. Kenics static mixer was
used for permeate flux enhancement. Turbidity and suspended solids
were removed and the permeate flux was continuously monitored
during the microfiltration process. The flux achieved after 90 minutes
of microfiltration was in a range of 50–70 l/m2h. The obtained
turbidity decrease was in the range of 50-99 % and total amount of
suspended solids was removed.
Abstract: This research presents the main ideas to implement an
intelligent system composed by communicating wireless sensors
measuring environmental data linked to drought indicators (such as
air temperature, soil moisture , etc...). On the other hand, the setting
up of a spatio temporal database communicating with a Web mapping
application for a monitoring in real time in activity 24:00 /day, 7
days/week is proposed to allow the screening of the drought
parameters time evolution and their extraction. Thus this system
helps detecting surfaces touched by the phenomenon of drought.
Spatio-temporal conceptual models seek to answer the users who
need to manage soil water content for irrigating or fertilizing or other
activities pursuing crop yield augmentation. Effectively, spatiotemporal
conceptual models enable users to obtain a diagram of
readable and easy data to apprehend. Based on socio-economic
information, it helps identifying people impacted by the phenomena
with the corresponding severity especially that this information is
accessible by farmers and stakeholders themselves. The study will be
applied in Siliana watershed Northern Tunisia.
Abstract: In insulation and cooling of power transformers
various liquids are used. Mineral oils have wide availability and low
cost. However, they have a poor biodegradability potential and lower
fire point in comparison with other insulating liquids. Use of a liquid
having high biodegradability is important due to environmental
consideration. This paper investigates edible corn oil as an alternative
to mineral oil. Various properties of mineral and corn oil like
breakdown voltage, dissipation factor, relative dielectric constant,
power loss and resistivity were measured according to different
standards.
Abstract: Studying on the response of vegetation phenology to
climate change at different temporal and spatial scales is important for
understanding and predicting future terrestrial ecosystem dynamics
and the adaptation of ecosystems to global change. In this study, the
Moderate Resolution Imaging Spectroradiometer (MODIS)
Normalized Difference Vegetation Index (NDVI) dataset and climate
data were used to analyze the dynamics of grassland phenology as well
as their correlation with climatic factors in different eco-geographic
regions and elevation units across the Tibetan Plateau. The results
showed that during 2003–2012, the start of the grassland greening
season (SOS) appeared later while the end of the growing season
(EOS) appeared earlier following the plateau’s precipitation and heat
gradients from southeast to northwest. The multi-year mean value of
SOS showed differences between various eco-geographic regions and
was significantly impacted by average elevation and regional average
precipitation during spring. Regional mean differences for EOS were
mainly regulated by mean temperature during autumn. Changes in
trends of SOS in the central and eastern eco-geographic regions were
coupled to the mean temperature during spring, advancing by about
7d/°C. However, in the two southwestern eco-geographic regions,
SOS was delayed significantly due to the impact of spring
precipitation. The results also showed that the SOS occurred later with
increasing elevation, as expected, with a delay rate of 0.66 d/100m.
For 2003–2012, SOS showed an advancing trend in low-elevation
areas, but a delayed trend in high-elevation areas, while EOS was
delayed in low-elevation areas, but advanced in high-elevation areas.
Grassland SOS and EOS changes may be influenced by a variety of
other environmental factors in each eco-geographic region.
Abstract: Because current wireless communication requires high
reliability in a limited bandwidth environment, this paper proposes
the variable modulation scheme based on the codebook. The variable
modulation scheme adjusts transmission power using the codebook in
accordance with channel state. Also, if the codebook is composed of
many bits, the reliability is more improved by the proposed scheme.
The simulation results show that the performance of proposed scheme
has better reliability than the the performance of conventional scheme.
Abstract: Industries produce millions of cubic meters of effluent
every year and the wastewater produced may be released into the
surrounding water bodies, treated on-site or at municipal treatment
plants. The determination of organic matter in the wastewater
generated is very important to avoid any negative effect on the
aquatic ecosystem. The scope of the present work is to assess the
physicochemical composition of the wastewater produced from one
of the brewery industry in South Africa. This is to estimate the
environmental impact of its discharge into the receiving water bodies
or the municipal treatment plant. The parameters monitored for the
quantitative analysis of brewery wastewater include biological
oxygen demand (BOD5), chemical oxygen demand (COD), total
suspended solids, volatile suspended solids, ammonia, total oxidized
nitrogen, nitrate, nitrite, phosphorus and alkalinity content. In
average, the COD concentration of the brewery effluent was 5340.97
mg/l with average pH values of 4.0 to 6.7. The BOD5 and the solids
content of the wastewater from the brewery industry were high. This
means that the effluent is very rich in organic content and its
discharge into the water bodies or the municipal treatment plant could
cause environmental pollution or damage the treatment plant. In
addition, there were variations in the wastewater composition
throughout the monitoring period. This might be as a result of
different activities that take place during the production process, as
well as the effects of peak period of beer production on the water
usage.
Abstract: The influence of physicochemical water quality
parameters on the abundance and diversity of caddisfly larvae was
studied in seven sampling stations in Mae Tao and Mae Ku
watersheds, Mae Sot District, Tak Province, northern Thailand. The
streams: MK2 and MK8 as reference site, and impacted streams
(MT1-MT5) were sampled bi-monthly during July 2011 to May
2012. A total of 4,584 individual of caddisfly larvae belonging to 10
family and 17 genera were found. The larvae of family
Hydropsychidae were the most abundance, followed by
Philopotamidae, Odontoceridae, and Leptoceridae, respectively. The
genus Cheumatopsyche, Hydropsyche, and Chimarra were the most
abundance genera in this study. Results of CCA ordination showed
the total dissolved solids, sulfate, water temperature, dissolved
oxygen and pH were the most important physicochemical factors to
affect distribution of caddisflies communities. Changes in the
caddisfly fauna may indicate changes in physicochemical factors
owing to agricultural pollution, urbanization, or other human
activities. Results revealed that the order Trichoptera, identified to
species or genus, can be potentially used to assess environmental
water quality status in freshwater ecosystems.
Abstract: Different terms of the Statistical Process Control (SPC)
has sketch in the fuzzy environment. However, Measurement System
Analysis (MSA), as a main branch of the SPC, is rarely investigated
in fuzzy area. This procedure assesses the suitability of the data to be
used in later stages or decisions of the SPC. Therefore, this research
focuses on some important measures of MSA and through a new
method introduces the measures in fuzzy environment. In this
method, which works based on Buckley approach, imprecision and
vagueness nature of the real world measurement are considered
simultaneously. To do so, fuzzy version of the gauge capability (Cg
and Cgk) are introduced. The method is also explained through
example clearly.
Abstract: The recent interest in alternative and renewable
energy systems results in increased installed capacity ratio of such
systems in total energy production of the world. Specifically, Wind
Energy Conversion Systems (WECS) draw significant attention
among possible alternative energy options, recently. On the contrary
of the positive points of penetrating WECS in all over the world in
terms of environment protection, energy independence of the
countries, etc., there are significant problems to be solved for the grid
connection of large scale WECS. The reactive power regulation,
voltage variation suppression, etc. can be presented as major issues to
be considered in this regard. Thus, this paper evaluates the
application of a Static VAr Compensator (SVC) unit for the reactive
power regulation and operation continuity of WECS during a fault
condition. The system is modeled employing the IEEE 13 node test
system. Thus, it is possible to evaluate the system performance with
an overall grid simulation model close to real grid systems. The
overall simulation model is developed in
MATLAB/Simulink/SimPowerSystems® environments and the
obtained results effectively match the target of the provided study.
Abstract: The development of transport systems has negative
impacts on the environment although it has beneficial effects on
society. The car policy caused many problems such as: - the
spectacular growth of fuel consumption hence the very vast increase
in urban pollution, traffic congestion in certain places and at certain
times, the increase in the number of accidents. The exhaust emissions
from cars and weather conditions are the main factors that determine
the level of pollution in urban atmosphere. These conditions lead to
the phenomenon of heat transfer and radiation occurring between the
air and the soil surface of any town. These exchanges give rise, in
urban areas, to the effects of heat islands that correspond to the
appearance of excess air temperature between the city and its
surrounding space. In this object, we perform a numerical simulation
of the plume generated by the cars exhaust gases and show that these
gases form a screening effect above the urban city which cause the
heat island in the presence of wind flow. This study allows us: 1. To
understand the different mechanisms of interactions between these
phenomena.2. To consider appropriate technical solutions to mitigate
the effects of the heat island.
Abstract: Based on the hypothesis that disaster risk is
constructed socially and historically, this article shows the
importance of keeping alive the historical memory of disaster by
means of architectural and urban heritage conservation. This is
illustrated with three examples of Latin American World Heritage
cities, where disasters like floods and earthquakes have shaped urban
form. Therefore, the study of urban form or "Urban Morphology" is
proposed as a tool to understand and analyze urban transformations
with the documentation of the occurrence of disasters. Lessons
learned from such cities may be useful to reduce disasters risk in
contemporary built environments.
Abstract: Life cycle assessment is a technique to assess the
environmental aspects and potential impacts associated with a
product, process, or service, by compiling an inventory of relevant
energy and material inputs and environmental releases; evaluating the
potential environmental impacts associated with identified inputs and
releases; and interpreting the results to help you make a more
informed decision. In this paper, the life cycle assessment of
aluminum and beech wood as two commonly used materials in Egypt
for window frames are heading, highlighting their benefits and
weaknesses. Window frames of the two materials have been assessed
on the basis of their production, energy consumption and
environmental impacts. It has been found that the climate change of
the windows made of aluminum and beech wood window, for a
reference window (1.2m×1.2m), are 81.7 mPt and -52.5 mPt impacts
respectively. Among the most important results are: fossil fuel
consumption, potential contributions to the green building effect and
quantities of solid waste tend to be minor for wood products
compared to aluminum products; incineration of wood products can
cause higher impacts of acidification and eutrophication than
aluminum, whereas thermal energy can be recovered.
Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.