Abstract: Nowadays, quasi-continuous wave diode lasers are
used in a widespread variety of applications. Temperature effects in
these lasers can strongly influence their performance. In this paper,
the effects of temperature have been experimentally investigated on
different features of a 60W-QCW diode laser. The obtained results
indicate that the conversion efficiency and operation voltage of diode
laser decrease with the augmentation of the working temperature
associated with a redshift in the laser peak wavelength. Experimental
results show the emission peak wavelength of laser shifts 0.26 nm
and the conversion efficiency decreases 1.76 % with the increase of
temperature from 40 to 50 ̊C. Present study also shows the slope
efficiency decreases gradually at low temperatures and rapidly at
higher temperatures. Regarding the close dependence of the
mentioned parameters to the operating temperature, it is of great
importance to carefully control the working temperature of diode
laser, particularly for medical applications.
Abstract: In most of the popular implementation of Parallel GAs
the whole population is divided into a set of subpopulations, each
subpopulation executes GA independently and some individuals are
migrated at fixed intervals on a ring topology. In these studies,
the migrations usually occur 'synchronously' among subpopulations.
Therefore, CPUs are not used efficiently and the communication
do not occur efficiently either. A few studies tried asynchronous
migration but it is hard to implement and setting proper parameter
values is difficult.
The aim of our research is to develop a migration method which is
easy to implement, which is easy to set parameter values, and which
reduces communication traffic. In this paper, we propose a traffic
reduction method for the Asynchronous Parallel Distributed GA by
migration of elites only. This is a Server-Client model. Every client
executes GA on a subpopulation and sends an elite information to the
server. The server manages the elite information of each client and
the migrations occur according to the evolution of sub-population in
a client. This facilitates the reduction in communication traffic.
To evaluate our proposed model, we apply it to many function optimization
problems. We confirm that our proposed method performs
as well as current methods, the communication traffic is less, and
setting of the parameters are much easier.
Abstract: In the last decades, a number of robust fuzzy clustering algorithms have been proposed to partition data sets affected by noise and outliers. Robust fuzzy C-means (robust-FCM) is certainly one of the most known among these algorithms. In robust-FCM, noise is modeled as a separate cluster and is characterized by a prototype that has a constant distance δ from all data points. Distance δ determines the boundary of the noise cluster and therefore is a critical parameter of the algorithm. Though some approaches have been proposed to automatically determine the most suitable δ for the specific application, up to today an efficient and fully satisfactory solution does not exist. The aim of this paper is to propose a novel method to compute the optimal δ based on the analysis of the distribution of the percentage of objects assigned to the noise cluster in repeated executions of the robust-FCM with decreasing values of δ . The extremely encouraging results obtained on some data sets found in the literature are shown and discussed.
Abstract: In the supply chain management customer is the most
significant component and mass customization is mostly related to
customers because it is the capability of any industry or organization
to deliver highly customized products and its services to the
respective customers with flexibility and integration, providing such
a variety of products that nearly everyone can find what they want.
Today all over the world many companies and markets are facing
varied situations that at one side customers are demanding that their
orders should be completed as quickly as possible while on other
hand it requires highly customized products and services. By
applying mass customization some companies face unwanted cost
and complexity. Now they are realizing that they should completely
examine what kind of customization would be best suited for their
companies. In this paper authors review some approaches and
principles which show effect in supply chain management that can be
adopted and used by companies for quickly meeting the customer
orders at reduced cost, with minimum amount of inventory and
maximum efficiency.
Abstract: Energy Efficiency Management is the heart of a
worldwide problem. The capability of a multi-agent system as a
technology to manage the micro-grid operation has already been
proved. This paper deals with the implementation of a decisional
pattern applied to a multi-agent system which provides intelligence to
a distributed local energy network considered at local consumer level.
Development of multi-agent application involves agent
specifications, analysis, design, and realization. Furthermore, it can
be implemented by following several decisional patterns. The
purpose of present article is to suggest a new approach for a
decisional pattern involving a multi-agent system to control a
distributed local energy network in a decentralized competitive
system. The proposed solution is the result of a dichotomous
approach based on environment observation. It uses an iterative
process to solve automatic learning problems and converges
monotonically very fast to system attracting operation point.
Abstract: In large Internet backbones, Service Providers
typically have to explicitly manage the traffic flows in order to
optimize the use of network resources. This process is often referred
to as Traffic Engineering (TE). Common objectives of traffic
engineering include balance traffic distribution across the network
and avoiding congestion hot spots. Raj P H and SVK Raja designed
the Bayesian network approach to identify congestion hors pots in
MPLS. In this approach for every node in the network the
Conditional Probability Distribution (CPD) is specified. Based on
the CPD the congestion hot spots are identified. Then the traffic can
be distributed so that no link in the network is either over utilized or
under utilized. Although the Bayesian network approach has been
implemented in operational networks, it has a number of well known
scaling issues.
This paper proposes a new approach, which we call the Pragati
(means Progress) Node Popularity (PNP) approach to identify the
congestion hot spots with the network topology alone. In the new
Pragati Node Popularity approach, IP routing runs natively over the
physical topology rather than depending on the CPD of each node as
in Bayesian network. We first illustrate our approach with a simple
network, then present a formal analysis of the Pragati Node
Popularity approach. Our PNP approach shows that for any given
network of Bayesian approach, it exactly identifies the same result
with minimum efforts. We further extend the result to a more
generic one: for any network topology and even though the network
is loopy. A theoretical insight of our result is that the optimal routing
is always shortest path routing with respect to some considerations of
hot spots in the networks.
Abstract: The effect of thermally induced stress on the modal
properties of highly elliptical core optical fibers is studied in this
work using a finite element method. The stress analysis is carried out
and anisotropic refractive index change is calculated using both the
conventional plane strain approximation and the generalized plane
strain approach. After considering the stress optical effect, the modal
analysis of the fiber is performed to obtain the solutions of
fundamental and higher order modes. The modal effective index,
modal birefringence, group effective index, group birefringence, and
dispersion of different modes of the fiber are presented. For
propagation properties, it can be seen that the results depend much on
the approach of stress analysis.
Abstract: A new and novel approach in medicine is the use of
cold plasma for various applications such as sterilization blood
coagulation and cancer cell treatment. In this paper a pin-to-hole
plasma jet suitable for biological applications is investigated and
characterized and the possibility and feasibility of cancer cell
treatment is evaluated. The characterization includes power
consumption via Lissajous method, thermal behavior of plasma using
Infra-red camera as a novel method, Optical Emission Spectroscopy
(OES) to determine the species that are generated. Treatment of
leukemia cancer cells is also implemented and MTT assay is used to
evaluate viability.
Abstract: Nowadays there are lots of applications of power and
free conveyors in logistics. They are the most frequently used
conveyor systems worldwide. Overhead conveyor technologies like
power and free systems are used in the most intra-logistics
applications in trade and industry. The automotive, food, beverage
and textile industry as well as aeronautic catering or engineering are
among the applications. Power and free systems employ different
manufacturing intervals in manufacturing as well as in production as
temporary store and buffer. Depending on the application area, power
and free conveyors are equipped with target controls enabling
complex distribution-and sorting tasks. This article introduces a new
power and free conveyor design in intra-logistics and explains its
components. According to the explanation of the components, a
model is created by means of their technical characteristics. Through
the CAD software, the model is visualized. After that, the static
analysis is evaluated. This analysis helps the calculation of the
mandatory state of structures under force action. This powerful model
helps companies achieve lower development costs as well as quicker
market maturity.
Abstract: This study examines appearances of brand placement
as an alternative communication strategy in television series by
focusing on Yalan Dünya which is one of the most popular television
series in Turkey. Consequently, this study has a descriptive research
design and quantitative content analysis method is used in order to
analyze frequency and time data of brand placement appearances in
first 3 seasons of Yalan Dünya with 16 episodes.
Analysis of brand placement practices in Yalan Dünya is dealt in
three categories: episode-based analysis, season-based analysis and
comparative analysis. At the end, brand placement practices in Yalan
Dünya are evaluated in terms of type, form, duration and legal
arrangements.
As a result of this study, it is seen that brand placement plays a
determinant role in Yalan Dünya content. Also, current legal
arrangements make brand placement closer to other traditional
communication strategies instead of differing brand placement from
them distinctly.
Abstract: Efficient handoff algorithms are a cost-effective way
of enhancing the capacity and QoS of cellular system. The higher
value of hysteresis effectively prevents unnecessary handoffs but
causes undesired cell dragging. This undesired cell dragging causes
interference or could lead to dropped calls in microcellular
environment. The problems are further exacerbated by the corner
effect phenomenon which causes the signal level to drop by 20-30 dB
in 10-20 meters. Thus, in order to maintain reliable communication
in a microcellular system new and better handoff algorithms must be
developed. A fuzzy based handoff algorithm is proposed in this paper
as a solution to this problem. Handoff on the basis of ratio of slopes
of normal signal loss to the actual signal loss is presented. The fuzzy
based solution is supported by comparing its results with the results
obtained in analytical solution.
Abstract: Atmospheric plasma is emerging as a promising
technology for many industrial sectors, because of its ecological and
economic advantages respect to the traditional production processes.
For textile industry, atmospheric plasma is becoming a valid
alternative to the conventional wet processes, but the plasma
machines realized so far do not allow the treatment of fibrous
mechanically weak material.
Novel atmospheric plasma machine for industrial applications,
developed by VenetoNanotech SCpA in collaboration with Italian
producer of corona equipment ME.RO SpA is presented. The main
feature of this pre-industrial scale machine is the possibility of the inline
plasma treatment of delicate fibrous substrates such as fibre
sleeves, for example wool tops, cotton fibres, polymeric tows,
mineral fibers and so on, avoiding burnings and disruption of the
faint materials.
Abstract: The stability of a software system is one of the most
important quality attributes affecting the maintenance effort. Many
techniques have been proposed to support the analysis of software
stability at the architecture, file, and class level of software systems,
but little effort has been made for that at the feature (i.e., method and
attribute) level. And the assumptions the existing techniques based
on always do not meet the practice to a certain degree. Considering
that, in this paper, we present a novel metric, Stability of Software
(SoS), to measure the stability of object-oriented software systems
by software change propagation analysis using a simulation way
in software dependency networks at feature level. The approach is
evaluated by case studies on eight open source Java programs using
different software structures (one employs design patterns versus one
does not) for the same object-oriented program. The results of the
case studies validate the effectiveness of the proposed metric. The
approach has been fully automated by a tool written in Java.
Abstract: The present work consecutively on synthesis and
characterization of composites, Al/Al alloy A 384.1 as matrix in
which the main ingredient as Al/Al-5% MgO alloy based metal
matrix composite. As practical implications the low cost processing
route for the fabrication of Al alloy A 384.1 and operational
difficulties of presently available manufacturing processes based in
liquid manipulation methods. As all new developments, complete
understanding of the influence of processing variables upon the final
quality of the product. And the composite is applied comprehensively
to the acquaintance for achieving superiority of information
concerning the specific heat measurement of a material through the
aid of thermographs. Products are evaluated concerning relative
particle size and mechanical behavior under tensile strength.
Furthermore, Taguchi technique was employed to examine the
experimental optimum results are achieved, owing to effectiveness of
this approach.
Abstract: Films of pure tin oxide SnO2 and in presence of
antimony atoms (SnO2-Sb) deposited onto glass substrates have
shown a sufficiently high energy gap to be transparent in the visible
region, a high electrical mobility and a carrier concentration which
displays a good electrical conductivity [1]. In this work, the effects of
polycrystalline silicon substrate on the optical properties of pure and
Sb doped tin oxide is investigated.
We used the APCVD (atmospheric pressure chemical vapour
deposition) technique, which is a low-cost and simple technique,
under nitrogen ambient, for growing this material. A series of SnO2
and SnO2-Sb have been deposited onto polycrystalline silicon
substrates with different contents of antimony atoms at the same
conditions of deposition (substrate temperature, flow oxygen,
duration and nitrogen atmosphere of the reactor). The effect of the
substrate in terms of morphology and nonlinear optical properties,
mainly the reflectance, was studied. The reflectance intensity of the
device, compared to the reflectance of tin oxide films deposited
directly on glass substrate, is clearly reduced on the overall
wavelength range. It is obvious that the roughness of the poly-c
silicon plays an important role by improving the reflectance and
hence the optical parameters.
A clear shift in the minimum of the reflectance upon doping level
is observed. This minimum corresponds to strong free carrier
absorption, resulting in different plasma frequency. This effect is
followed by an increase in the reflectance depending of the antimony
doping. Applying the extended Drude theory to the combining
optical and electrical obtained results these effects are discussed.
Abstract: This paper covers the present situation and problem of experimental teaching of mathematics specialty in recent years, puts
forward and demonstrates experimental teaching methods for different
education. From the aspects of content and experimental teaching
approach, uses as an example the course “Experiment for Program
Designing & Algorithmic Language" and discusses teaching practice
and laboratory course work. In addition a series of successful methods
and measures are introduced in experimental teaching.
Abstract: This paper proposes an investment cost recovery
based efficient and fast sequential optimization approach to optimal
allocation of thyristor controlled series compensator (TCSC) in
competitive power market. The optimization technique has been used
with an objective to maximizing the social welfare and minimizing
the device installation cost by suitable location and rating of TCSC in
the system. The effectiveness of proposed approach for location of
TCSC has been compared with some existing methods of TCSC
placement, in terms of its impact on social welfare, TCSC investment
recovery and optimal generation as well as load patterns. The results
have been obtained on modified IEEE 14-bus system.
Abstract: In this paper, the test purpose will be to assess
whether or not the accelerated model proposed by Eyring will be able
to translate results for the shape and scale parameters of an
underlying Weibull model, obtained under two accelerating using
conditions, to expected normal using condition results for these
parameters. The product being analyzed is a new type of insulate
fluid, and the accelerating factor is the voltage stresses applied to the
fluid at two different levels (30KV and 40KV). The normal operating
voltage is 25KV. In this case, it was possible to test the insulate fluid
at normal voltage using condition. Both results for the two
parameters of the Weibull model, obtained under normal using
condition and translated from accelerated using conditions to normal
conditions, will be compared to each other to assess the accuracy of
the Eyring model when the accelerating factor is only the voltage
stress.
Abstract: This paper presents an application of the improved
QFD method for determining the specifications of kitchen utensils
rack. By using the improved method, the subjective nature in original
QFD was reduced; particularly in defining the relationship between
customer requirement and engineering characteristics. The regression
analysis that was used for obtaining the relationship functions
between customer requirement and engineering characteristics also
accommodated the inaccurateness of the competitive assessment
results. The improved method which is represented in the form of a
mathematical model had become a formal guidance to allocate the
resource for improving the specifications of kitchen utensils rack.
The specifications obtained had led to the achievement of the highest
feasible customer satisfaction.
Abstract: Overhead conveyor systems satisfy by their simple
construction, wide application range and their full compatibility with
other manufacturing systems, which are designed according to
international standards. Ultra-light overhead conveyor systems are
rope-based conveying systems with individually driven vehicles. The
vehicles can move automatically on the rope and this can be realized
by energy and signals. Crossings are realized by switches. Overhead
conveyor systems are particularly used in the automotive industry but
also at post offices. Overhead conveyor systems always must be
integrated with a logistical process by finding the best way for a
cheaper material flow and in order to guarantee precise and fast
workflows. With their help, any transport can take place without
wasting ground and space, without excessive company capacity, lost
or damaged products, erroneous delivery, endless travels and without
wasting time. Ultra-light overhead conveyor systems provide optimal
material flow, which produces profit and saves time. This article
illustrates the advantages of the structure of the ultra-light overhead
conveyor systems in logistics applications and explains the steps of
their system design. After an illustration of the steps, currently
available systems on the market will be shown by means of their
technical characteristics. Due to their simple construction, demands
to an ultra-light overhead conveyor system will be illustrated.