Abstract: The aim of this paper is to study the internal
stabilization of the Bernoulli-Euler equation numerically. For this,
we consider a square plate subjected to a feedback/damping force
distributed only in a subdomain. An algorithm for obtaining an
approximate solution to this problem was proposed and implemented.
The numerical method used was the Finite Difference Method.
Numerical simulations were performed and showed the behavior of
the solution, confirming the theoretical results that have already been
proved in the literature. In addition, we studied the validation of the
numerical scheme proposed, followed by an analysis of the numerical
error; and we conducted a study on the decay of the energy associated.
Abstract: For micro-gyroscopes, the angular rate detection components have to oscillate forwards and backwards alternatively. An innovative design of micro-electromagnetic drive module is proposed to make a Π-type disc reciprocally and efficiently rotate within a certain of angular interval. Twelve Electromagnetic poles enclosing the thin disc are designed to provide the magnetic drive power. Isotropic etching technique is employed to fabricate the high-aspect-ratio trench, so that the contact angle of wire against trench can be increased and the potential defect of cavities and pores within the wire can be prevented. On the other hand, a Π-type thin disc is designed to conduct the pitch motion as an angular excitation, in addition to spinning, is exerted on the gyroscope. The efficacy of the micro-magnetic drive module is verified by the commercial software, Ansoft Maxewll. In comparison with the conventional planar windings in micro-scale systems, the magnetic drive force is increased by 150%.
Abstract: Existing proceeding-models for the development of mechatronic systems provide a largely parallel action in the detailed development. This parallel approach is to take place also largely independent of one another in the various disciplines involved. An approach for a new proceeding-model provides a further development of existing models to use for the development of Adaptronic Systems. This approach is based on an intermediate integration and an abstract modeling of the adaptronic system. Based on this system-model a simulation of the global system behavior, due to external and internal factors or Forces is developed. For the intermediate integration a special data management system is used. According to the presented approach this data management system has a number of functions that are not part of the "normal" PDM functionality. Therefore a concept for a new data management system for the development of Adaptive system is presented in this paper. This concept divides the functions into six layers. In the first layer a system model is created, which divides the adaptronic system based on its components and the various technical disciplines. Moreover, the parameters and properties of the system are modeled and linked together with the requirements and the system model. The modeled parameters and properties result in a network which is analyzed in the second layer. From this analysis necessary adjustments to individual components for specific manipulation of the system behavior can be determined. The third layer contains an automatic abstract simulation of the system behavior. This simulation is a precursor for network analysis and serves as a filter. By the network analysis and simulation changes to system components are examined and necessary adjustments to other components are calculated. The other layers of the concept treat the automatic calculation of system reliability, the "normal" PDM-functionality and the integration of discipline-specific data into the system model. A prototypical implementation of an appropriate data management with the addition of an automatic system development is being implemented using the data management system ENOVIA SmarTeam V5 and the simulation system MATLAB.
Abstract: The quantified residence time distribution (RTD)
provides a numerical characterization of mixing in a reactor, thus
allowing the process engineer to better understand mixing
performance of the reactor.This paper discusses computational
studies to investigate flow patterns in a two impinging streams
cyclone reactor(TISCR) . Flow in the reactor was modeled with
computational fluid dynamics (CFD). Utilizing the Eulerian-
Lagrangian approach, implemented in FLUENT (V6.3.22), particle
trajectories were obtained by solving the particle force balance
equations. From simulation results obtained at different Δts, the mean
residence time (tm) and the mean square deviation (σ2) were
calculated. a good agreement can be observed between predicted and
experimental data. Simulation results indicate that the behavior of
complex reactor systems can be predicted using the CFD technique
with minimum data requirement for validation.
Abstract: As it is known, buoyancy and drag forces rule bubble's rise velocity in a liquid column. These forces are strongly dependent on fluid properties, gravity as well as equivalent's diameter. This study reports a set of bubble rising velocity experiments in a liquid column using water or glycerol. Several records of terminal velocity were obtained. The results show that bubble's rise terminal velocity is strongly dependent on dynamic viscosity effect. The data set allowed to have some terminal velocities data interval of 8.0 ? 32.9 cm/s with Reynolds number interval 1.3 -7490. The bubble's movement was recorded with a video camera. The main goal is to present an original set data and results that will be discussed based on two-phase flow's theory. It will also discussed, the prediction of terminal velocity of a single bubble in liquid, as well as the range of its applicability. In conclusion, this study presents general expressions for the determination of the terminal velocity of isolated gas bubbles of a Reynolds number range, when the fluid proprieties are known.
Abstract: This article presents a numerical study of the doublediffusive
mixed convection in a vertical channel filled with porous
medium by using non-equilibrium model. The flow is assumed
fully developed, uni-directional and steady state. The controlling
parameters are thermal Rayleigh number (RaT ), Darcy number (Da),
Forchheimer number (F), buoyancy ratio (N), inter phase heat transfer
coefficient (H), and porosity scaled thermal conductivity ratio
(γ). The Brinkman-extended non-Darcy model is considered. The
governing equations are solved by spectral collocation method. The
main emphasize is given on flow profiles as well as heat and solute
transfer rates, when two diffusive components in terms of buoyancy
ratio are in favor (against) of each other and solid matrix and fluid
are thermally non-equilibrium. The results show that, for aiding flow
(RaT = 1000), the heat transfer rate of fluid (Nuf ) increases upto a
certain value of H, beyond that decreases smoothly and converges
to a constant, whereas in case of opposing flow (RaT = -1000),
the result is same for N = 0 and 1. The variation of Nuf in (N,
Nuf )-plane shows sinusoidal pattern for RaT = -1000. For both cases
(aiding and opposing) the flow destabilize on increasing N by inviting
point of inflection or flow separation on the velocity profile. Overall,
the buoyancy force have significant impact on the non-Darcy mixed
convection under LTNE conditions.
Abstract: A multiple-option analytical model for the evaluation of the energy performance and distribution of aerodynamic forces acting on a vertical-axis Darrieus wind turbine depending on both rotor architecture and operating conditions is presented. For this purpose, a numerical algorithm, capable of generating the desired rotor conformation depending on design geometric parameters, is coupled to a Single/Double-Disk Multiple-Streamtube Blade Element – Momentum code. Both single and double-disk configurations are analyzed and model predictions are compared to literature experimental data in order to test the capability of the code for predicting rotor performance. Effective airfoil characteristics based on local blade Reynolds number are obtained through interpolation of literature low-Reynolds airfoil databases. Some corrections are introduced inside the original model with the aim of simulating also the effects of blade dynamic stall, rotor streamtube expansion and blade finite aspect ratio, for which a new empirical relationship to better fit the experimental data is proposed. In order to predict also open field rotor operation, a freestream wind shear profile is implemented, reproducing the effect of atmospheric boundary layer.
Abstract: The top-heavy demographic of low birth-rate and longer lifespan is a growing social problem, and one of its expected effects will be a shortage of young workers and a growing reliance on a workforce of middle-aged and older people. However, the environment of today's industrial workplace is not particularly suited to middle-aged and older workers, one notable problem being temperature control. Higher temperatures can cause health problems such as heat stroke, and the number of cases increases sharply in people over 65. Moreover, in conditions above 33°C, older people can develop circulatory system disorders, and also have a higher chance of suffering a fatal heart attack. We therefore propose a new method for controlling temperature in the indoor workplace. In this study two different verification experiments were conducted, with the proposed temperature control method being tested in cargo containers and conventional houses. The method's effectiveness was apparent in measurements of temperature and electricity consumption
Abstract: It is widely acknowledged that there is a shortage of software developers, not only in South Africa, but also worldwide. Despite reports on a gap between industry needs and software education, the gap has mostly been explored in quantitative studies. This paper reports on the qualitative data of a mixed method study of the perceptions of professional software developers regarding what topics they learned from their formal education and the importance of these topics to their actual work. The analysis suggests that there is a gap between industry’s needs and software development education and the following recommendations are made: 1) Real-life projects must be included in students’ education; 2) Soft skills and business skills must be included in curricula; 3) Universities must keep the curriculum up to date; 4) Software development education must be made accessible to a diverse range of students.
Abstract: This study focuses on teamwork in Finnish working
life. Through a wide cross-section of teams the study examines the
causes to which team members attribute the outcomes of their teams.
Qualitative data was collected from 314 respondents. They wrote 616
stories to describe memorable experiences of success and failure in
teamwork. The stories revealed 1930 explanations. The findings
indicate that both favorable and unfavorable team outcomes are
perceived as being caused by the characteristics of team members,
relationships between members, team communication, team
structure, team goals, team leadership, and external forces. The types
represent different attribution levels in the context of organizational
teamwork.
Abstract: Noise level has critical effects on the diagnostic
performance of signal-averaged electrocardiogram (SAECG), because
the true starting and end points of QRS complex would be masked by
the residual noise and sensitive to the noise level. Several studies and
commercial machines have used a fixed number of heart beats
(typically between 200 to 600 beats) or set a predefined noise level
(typically between 0.3 to 1.0 μV) in each X, Y and Z lead to perform
SAECG analysis. However different criteria or methods used to
perform SAECG would cause the discrepancies of the noise levels
among study subjects. According to the recommendations of 1991
ESC, AHA and ACC Task Force Consensus Document for the use of
SAECG, the determinations of onset and offset are related closely to
the mean and standard deviation of noise sample. Hence this study
would try to perform SAECG using consistent root-mean-square
(RMS) noise levels among study subjects and analyze the noise level
effects on SAECG. This study would also evaluate the differences
between normal subjects and chronic renal failure (CRF) patients in
the time-domain SAECG parameters.
The study subjects were composed of 50 normal Taiwanese and 20
CRF patients. During the signal-averaged processing, different RMS
noise levels were adjusted to evaluate their effects on three time
domain parameters (1) filtered total QRS duration (fQRSD), (2) RMS
voltage of the last QRS 40 ms (RMS40), and (3) duration of the low
amplitude signals below 40 μV (LAS40). The study results
demonstrated that the reduction of RMS noise level can increase
fQRSD and LAS40 and decrease the RMS40, and can further increase
the differences of fQRSD and RMS40 between normal subjects and
CRF patients. The SAECG may also become abnormal due to the
reduction of RMS noise level. In conclusion, it is essential to establish
diagnostic criteria of SAECG using consistent RMS noise levels for
the reduction of the noise level effects.
Abstract: This work presents a low-cost and eco-friendly
building material named Agrostone panel. Africa-s urban population
is growing at an annual rate of 2.8% and 62% of its population will
live in urban areas by 2050. As a consequence, many of the least
urbanized and least developed African countries- will face serious
challenges in providing affordable housing to the urban dwellers.
Since the cost of building materials accounts for the largest
proportion of the overall construction cost, innovating low-cost
building material is vital. Agrostone panel is used in housing projects
in Ethiopia. It uses raw materials of agricultural/industrial wastes
and/or natural minerals as a filler, magnesium-based chemicals as a
binder and fiberglass as reinforcement. Agrostone panel reduces the
cost of wall construction by 50% compared with the conventional
building materials. The pros and cons of Agrostone panel as well as
the use of other waste materials as a raw material to make the panel
more sustainable, low-cost and better properties are discussed.
Abstract: Among the chemicals used for ammunition production, TNT (Trinitrotoluene) play a significant role since World War I and II. Various types of military weapon utilize TNT in casting process. However, the TNT casting process for warhead is difficult to control the cooling rate of the liquid TNT. This problem occurs because the casting process lacks the equipment to detect the temperature during the casting procedure This study presents the temperature detected by infrared camera to illustrate the cooling rate and cooling zone of curing, and demonstrates the optimization of TNT condition to reduce the risk of air gap occurred in the warhead which can result in the destruction afterward. Premature initiation of explosive-filled projectiles in response to set-back forces during gunfiring cause by casting defects. Finally the study can help improving the process of the TNT casting. The operators can control the curing of TNT inside the case by rising up the heating rod at the proper time. Consequently this can reduce tremendous time of rework if the air gaps occur and increase strength to lower elastic modulus. Therefore, it can be clearly concluded that the use of Infrared Cameras in this process is another method to improve the casting procedure.
Abstract: International markets driven forces are changing
continuously, therefore companies need to gain a competitive edge in
such markets. Improving the company's products, processes and
practices is no longer auxiliary. Lean production is a production
management philosophy that consolidates work tasks with minimum
waste resulting in improved productivity. Lean production practices
can be mapped into many production areas. One of these is
Manufacturing Equipment and Technology (MET). Many lean
production practices can be implemented in MET, namely, specific
equipment configurations, total preventive maintenance, visual
control, new equipment/ technologies, production process
reengineering and shared vision of perfection.The purpose of this
paper is to investigate the implementation level of these six practices
in Jordanian industries. To achieve that a questionnaire survey has
been designed according to five-point Likert scale. The questionnaire
is validated through pilot study and through experts review. A sample
of 350 Jordanian companies were surveyed, the response rate was
83%. The respondents were asked to rate the extent of
implementation for each of practices. A relationship conceptual
model is developed, hypotheses are proposed, and consequently the
essential statistical analyses are then performed. An assessment tool
that enables management to monitor the progress and the
effectiveness of lean practices implementation is designed and
presented. Consequently, the results show that the average
implementation level of lean practices in MET is 77%, Jordanian
companies are implementing successfully the considered lean
production practices, and the presented model has Cronbach-s alpha
value of 0.87 which is good evidence on model consistency and
results validation.
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: The design of an active leg orthosis for tumble
protection is proposed in this paper. The orthosis would be applied to
assist elders or invalids in rebalancing while they fall unexpectedly.
We observe the regain balance motion of healthy and youthful people,
and find the difference to elders or invalids. First, the physical model
of leg would be established, and we consider the leg motions are
achieve through four joints (phalanx stem, ankle, knee, and hip joint)
and five links (phalanges, talus, tibia, femur, and hip bone). To
formulate the dynamic equations, the coordinates which can clearly
describe the position in 3D space are first defined accordance with the
human movement of leg, and the kinematics and dynamics of the leg
movement can be formulated based on the robotics. For the purpose,
assisting elders and invalids in avoiding tumble, the posture variation
of unbalance and regaining balance motion are recorded by the
motion-capture image system, and the trajectory is taken as the desire
one. Then we calculate the force and moment of each joint based on
the leg motion model through programming MATLAB code. The
results would be primary information of the active leg orthosis design
for tumble protection.
Abstract: Applying corona wind as a novel technique can lead
to a great level of heat and mass transfer augmentation by using very
small amount of energy. Enhancement of forced flow evaporation
rate by applying electric field (corona wind) has been experimentally
evaluated in this study. Corona wind produced by a fine wire
electrode which is charged with positive high DC voltage impinges
to water surface and leads to evaporation enhancement by disturbing
the saturated air layer over water surface. The study was focused on
the effect of corona wind velocity, electrode spacing and air flow
velocity on the level of evaporation enhancement. Two sets of
experiments, i.e. with and without electric field, have been
conducted. Data obtained from the first experiment were used as
reference for evaluation of evaporation enhancement at the presence
of electric field. Applied voltages ranged from corona threshold
voltage to spark over voltage at 1 kV increments. The results showed
that corona wind has great enhancement effect on water evaporation
rate, but its effectiveness gradually diminishes by increasing air flow
velocity. Maximum enhancements were 7.3 and 3.6 for air velocities
of 0.125 and 1.75 m/s, respectively.
Abstract: Social resilience has role to govern the local community and coastal fisheries resources toward sustainable fisheries development in tsunami affected area. This paper asses, explore and investigates of indigenous institutions, external and internal facilitators toward strengthening social resilience. Identification of the genuine organizations role had been conducted twice by using Rapid Assessment Appraisal, Focus Group Discussion, and in-depth interview for collecting primary and secondary data. Local wisdom had a contribution and adaptable to rebound social resilience. The Panglima Laot Lhok (sea commander) had determined and adapted role on recovery of the fishing community, particularly facilitated aid delivery to fishermen, as shown in anchovy fisheries relief case in Krueng Raya Bay. Toke Bangku (financial trader) had stimulated for reinforcement of advance payment and market channel. The other institutions supported upon linking and bridging connectivity among stakeholders. Collaborative governance can avoid conflict, reduce donor dependency and strengthen social resilience within fishing community.
Abstract: The objective of the present investigation was to
evaluate the morphology of Escherchia coli bacteria in interaction
with SiO2 nanoparticles.
This study was made by atomic force microscopy and quartz
crystal microbalance using SiO2 nanoparticles with 10nm, 50nm and
100nm diameter and bacteria immobilized on polyelectrolyte
multilayer films obtained by spin coating or by “layer by layer”
(LbL) method.
Abstract: The steady-state operation of maintaining voltage
stability is done by switching various controllers scattered all over
the power network. When a contingency occurs, whether forced or
unforced, the dispatcher is to alleviate the problem in a minimum
time, cost, and effort. Persistent problem may lead to blackout. The
dispatcher is to have the appropriate switching of controllers in terms
of type, location, and size to remove the contingency and maintain
voltage stability. Wrong switching may worsen the problem and that
may lead to blackout. This work proposed and used a Fuzzy CMeans
Clustering (FCMC) to assist the dispatcher in the decision
making. The FCMC is used in the static voltage stability to map
instantaneously a contingency to a set of controllers where the types,
locations, and amount of switching are induced.