Abstract: According to the governmental data, the cases of oral
cancers doubled in the past 10 years. This had brought heavy burden to
the patients- family, the society, and the country. The literature
generally evidenced the betel nut contained particular chemicals that
can cause oral cancers. Research in Taiwan had also proofed that 90
percent of oral cancer patients had experience of betel nut chewing. It
is thus important to educate the betel-nut hobbyists to cease such a
hazardous behavior. A program was then organized to establish
several training classes across different areas specific to help ceasing
this particular habit. Purpose of this research was to explore the
attitude and intention toward ceasing betel-nut chewing before and
after attending the training classes. 50 samples were taken from a
ceasing class with average age at 45 years old with high school
education (54%). 74% of the respondents were male in service or
agricultural industries. Experiences in betel-nut chewing were 5-20
years with a dose of 1-20 pieces per day. The data had shown that 60%
of the respondents had cigarette smoking habit, and 30% of the
respondents were concurrently alcoholic dependent. Research results
indicated that the attitude, intentions, and the knowledge on oral
cancers were found significant different between before and after
attendance. This provided evidence for the effectiveness of the training
class. However, we do not perform follow-up after the class.
Noteworthy is the test result also shown that participants who were
drivers as occupation, or habitual smokers or alcoholic dependents
would be less willing to quit the betel-nut chewing. The test results
indicated as well that the educational levels and the type of occupation
may have significant impacts on an individual-s decisions in taking
betel-nut or substance abuse.
Abstract: Power transformer consists of components which are
under consistent thermal and electrical stresses. The major
component which degrades under these stresses is the paper
insulation of the power transformer. At site, lightning impulses and
cable faults may cause the winding deformation. In addition, the
winding may deform due to impact during transportation. A
deformed winding will excite more stress to its insulating paper thus
will degrade it. Insulation degradation will shorten the life-span of
the transformer. Currently there are two methods of detecting the
winding deformation which are Sweep Frequency Response
Analysis (SFRA) and Low Voltage Impulse Test (LVI). The latter
injects current pulses to the winding and capture the admittance
plot. In this paper, a transformer which experienced overheating and
arcing was identified, and both SFRA and LVI were performed.
Next, the transformer was brought to the factory for untanking. The
untanking results revealed that the LVI is more accurate than the
SFRA method for this case study.
Abstract: The UK Government has emphasized the role of Local Authorities as a key player in its flagship residential energy efficiency strategies, by identifying and targeting areas for energy efficiency improvements. Residential energy consumption in England is characterized by significant geographical variation in energy demand, which makes centralized targeting of areas for energy efficiency intervention difficult. This paper draws on research which aims to understand how demographic, social, economic, urban form and climatic factors influence the geographical variations in English residential gas consumption. The paper reports the findings of a multiple regression model that shows how 64% of the geographical variation in residential gas consumption is accounted for by variations in these factors. Results from this study, after further refinement and validation, can be used by Local Authorities to identify areas within their boundaries that have higher than expected gas consumption, these may be prime targets for energy efficiency initiatives.
Abstract: Recently, genetic algorithms (GA) and particle swarm optimization (PSO) technique have attracted considerable attention among various modern heuristic optimization techniques. The GA has been popular in academia and the industry mainly because of its intuitiveness, ease of implementation, and the ability to effectively solve highly non-linear, mixed integer optimization problems that are typical of complex engineering systems. PSO technique is a relatively recent heuristic search method whose mechanics are inspired by the swarming or collaborative behavior of biological populations. In this paper both PSO and GA optimization are employed for finding stable reduced order models of single-input- single-output large-scale linear systems. Both the techniques guarantee stability of reduced order model if the original high order model is stable. PSO method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. Both the methods are illustrated through numerical example from literature and the results are compared with recently published conventional model reduction technique.
Abstract: Aiming at most of the aviation products are facing the problem of fatigue fracture in vibration environment, we makes use of the testing result of a bracket, analysis for the structure with ANSYS-Workbench, predict the life of the bracket by different ways, and compared with the testing result. With the research on analysis methods, make an organic combination of simulation analysis and testing, Not only ensure the accuracy of simulation analysis and life predict, but also make a dynamic supervision of product life process, promote the application of finite element simulation analysis in engineering practice.
Abstract: One of the processes of slope that occurs every year in Iran and some parts of world and cause a lot of criminal and financial harms is called landslide. They are plenty of method to stability landslide in soil and rock slides. The use of the best method with the least cost and in the shortest time is important for researchers. In this research, determining the best method of stability is investigated by using of Decision Support systems. DSS is made for this purpose and was used (for Hasan Salaran area in Kurdistan). Field study data from topography, slope, geology, geometry of landslide and the related features was used. The related data entered decision making managements programs (DSS) (ALES).Analysis of mass stability indicated the instability potential at present. Research results show that surface and sub surface drainage the best method of stabilizing. Analysis of stability shows that acceptable increase in security coefficient is a consequence of drainage.
Abstract: The objective of this research is to develop the
performance indicators (PIs) in operational level for the Pre-hospital Emergency Medical Service (EMS) system employing in Thailand. This research started with ascertaining the current pre-hospital care
system. The team analyzed the strategies of Narerthorn, a government unit under the ministry of public health, and the existing PIs of the pre-hospital care. Afterwards, the current National Strategic Plan of EMS development (2008-2012) of the Emergency
Medical Institute of Thailand (EMIT) was considered using strategic
analysis to developed Strategy Map (SM) and identified the Success
Factors (SFs). The analysis results from strategy map and SFs were used to develop the Performance Indicators (PIs). To verify the set of
PIs, the team has interviewed with the relevant practitioners for the possibilities to implement the PIs. To this paper, it was to ascertain
that all the developed PIs support the objectives of the strategic plan. Nevertheless, the results showed that the operational level PIs suited
only with the first dimension of National Strategic Plan
(infrastructure and information technology development). Besides,
the SF was the infrastructure development (to contribute the EMS system to people throughout with standard and efficiency both in normally and disaster conditions). Finally, twenty-nine indicators
were developed from the analysis results of SM and SFs.
Abstract: This is an application research presenting the
improvement of production quality using the six sigma solutions and
the analyses of benefit-cost ratio. The case of interest is the
production of tile-concrete. Such production has faced with the
problem of high nonconforming products from an inappropriate
surface coating and had low process capability based on the strength
property of tile. Surface coating and tile strength are the most critical
to quality of this product. The improvements followed five stages of
six sigma solutions. After the improvement, the production yield was
improved to 80% as target required and the defective products from
coating process was remarkably reduced from 29.40% to 4.09%. The
process capability based on the strength quality was increased from
0.87 to 1.08 as customer oriented. The improvement was able to save
the materials loss for 3.24 millions baht or 0.11 million dollars. The
benefits from the improvement were analyzed from (1) the reduction
of the numbers of non conforming tile using its factory price for
surface coating improvement and (2) the materials saved from the
increment of process capability. The benefit-cost ratio of overall
improvement was high as 7.03. It was non valuable investment in
define, measure, analyses and the initial of improve stages after that
it kept increasing. This was due to there were no benefits in define,
measure, and analyze stages of six sigma since these three stages
mainly determine the cause of problem and its effects rather than
improve the process. The benefit-cost ratio starts existing in the
improve stage and go on. Within each stage, the individual benefitcost
ratio was much higher than the accumulative one as there was an
accumulation of cost since the first stage of six sigma. The
consideration of the benefit-cost ratio during the improvement
project helps make decisions for cost saving of similar activities
during the improvement and for new project. In conclusion, the
determination of benefit-cost ratio behavior through out six sigma
implementation period provides the useful data for managing quality
improvement for the optimal effectiveness. This is the additional
outcome from the regular proceeding of six sigma.
Abstract: Above Elbow Prosthesis is one of the most commonly
amputated or missing limbs. The research is done for modelling
techniques of upper limb prosthesis and design of high torque, light
weight and compact in size elbow actuator. The purposed actuator
consists of a DC motor, planetary gear set and a harmonic drive. The
calculations show that the actuator is good enough to be used in real
life powered prosthetic upper limb or rehabilitation exoskeleton.
Abstract: The objective of this paper is to study the electrical
resistivity complexity between field and laboratory measurement, in
order to improve the effectiveness of data interpretation for
geophysical ground resistivity survey. The geological outcrop in
Penang, Malaysia with an obvious layering contact was chosen as the
study site. Two dimensional geoelectrical resistivity imaging were
used in this study to maps the resistivity distribution of subsurface,
whereas few subsurface sample were obtained for laboratory
advance. In this study, resistivity of samples in original conditions is
measured in laboratory by using time domain low-voltage technique,
particularly for granite core sample and soil resistivity measuring set
for soil sample. The experimentation results from both schemes are
studied, analyzed, calibrated and verified, including basis and
correlation, degree of tolerance and characteristics of substance.
Consequently, the significant different between both schemes is
explained comprehensively within this paper.
Abstract: Parallel programming models exist as an abstraction
of hardware and memory architectures. There are several parallel
programming models in commonly use; they are shared memory
model, thread model, message passing model, data parallel model,
hybrid model, Flynn-s models, embarrassingly parallel computations
model, pipelined computations model. These models are not specific
to a particular type of machine or memory architecture. This paper
expresses the model program for concurrent approach to data parallel
model through java programming.
Abstract: The aluminum bronze matrix alumina composites using hot press and resin infiltration were investigated to study their porosities, hardness, bending strengths, and microstructures. The experiment results show that the hardness of the sintered composites with the decrease of porosity increases. The composites without and with resin infiltration have about HRF 42-61 of about 34-40% of porosity and about HRF 62-83 of about 30-36% of porosity, respectively. Besides, the alumina composites contain a more amount of iron and nickel powders would cause a lower bending strength due to forming some weaker bonding among the iron, nickel, copper, aluminum under this hot pressing of shorter time.
Abstract: This paper presents a compact thermoelectric power generator system based on temperature difference across the element. The system can transfer the burning heat energy to electric energy directly. The proposed system has a thermoelectric generator and a power control box. In the generator, there are 4 thermoelectric modules (TEMs), each of which uses 2 thermoelectric chips (TEs) and 2 cold sinks, 1 thermal absorber, and 1 thermal conduction flat board. In the power control box, there are 1 storing energy device, 1 converter, and 1 inverter. The total net generating power is about 11W. This system uses commercial portable gas stoves or burns timber or the coal as the heat source, which is easily obtained. It adopts solid-state thermoelectric chips as heat inverter parts. The system has the advantages of being light-weight, quite, and mobile, requiring no maintenance, and havng easily-supplied heat source. The system can be used a as long as burning is allowed. This system works well for highly-mobilized outdoors situations by providing a power for illumination, entertainment equipment or the wireless equipment at refuge. Under heavy storms such as typhoon, when the solar panels become ineffective and the wind-powered machines malfunction, the thermoelectric power generator can continue providing the vital power.
Abstract: Histogram equalization is often used in image enhancement, but it can be also used in auto exposure. However, conventional histogram equalization does not work well when many pixels are concentrated in a narrow luminance range.This paper proposes an auto exposure method based on 2-way histogram equalization. Two cumulative distribution functions are used, where one is from dark to bright and the other is from bright to dark. In this paper, the proposed auto exposure method is also designed and implemented for image signal processors with full-HD images.
Abstract: The issue of unintentional islanding in PV grid
interconnection still remains as a challenge in grid-connected
photovoltaic (PV) systems. This paper discusses the overview of
popularly used anti-islanding detection methods, practically applied
in PV grid-connected systems. Anti-islanding methods generally can
be classified into four major groups, which include passive methods,
active methods, hybrid methods and communication base methods.
Active methods have been the preferred detection technique over the
years due to very small non-detected zone (NDZ) in small scale
distribution generation. Passive method is comparatively simpler
than active method in terms of circuitry and operations. However, it
suffers from large NDZ that significantly reduces its performance.
Communication base methods inherit the advantages of active and
passive methods with reduced drawbacks. Hybrid method which
evolved from the combination of both active and passive methods
has been proven to achieve accurate anti-islanding detection by many
researchers. For each of the studied anti-islanding methods, the
operation analysis is described while the advantages and
disadvantages are compared and discussed. It is difficult to pinpoint a
generic method for a specific application, because most of the
methods discussed are governed by the nature of application and
system dependent elements. This study concludes that the setup and
operation cost is the vital factor for anti-islanding method selection in
order to achieve minimal compromising between cost and system
quality.
Abstract: This paper proposes a method, combining color and
layout features, for identifying documents captured from lowresolution
handheld devices. On one hand, the document image color
density surface is estimated and represented with an equivalent
ellipse and on the other hand, the document shallow layout structure
is computed and hierarchically represented. The combined color and
layout features are arranged in a symbolic file, which is unique for
each document and is called the document-s visual signature. Our
identification method first uses the color information in the
signatures in order to focus the search space on documents having a
similar color distribution, and finally selects the document having the
most similar layout structure in the remaining search space. Finally,
our experiment considers slide documents, which are often captured
using handheld devices.
Abstract: This study reveals that anti-immigrant policies in
Europe result from a process of securitization, and that, within this
process, radical right parties have been formulating discourses and
approaches through a construction process by using some common
security themes. These security themes can be classified as national
security, economic security, cultural security and internal security.
The frequency with which radical right parties use these themes may
vary according to the specific historical, social and cultural
characteristics of a particular country.
Abstract: This paper presents a new steganography approach suitable for Arabic texts. It can be classified under steganography feature coding methods. The approach hides secret information bits within the letters benefiting from their inherited points. To note the specific letters holding secret bits, the scheme considers the two features, the existence of the points in the letters and the redundant Arabic extension character. We use the pointed letters with extension to hold the secret bit 'one' and the un-pointed letters with extension to hold 'zero'. This steganography technique is found attractive to other languages having similar texts to Arabic such as Persian and Urdu.
Abstract: A conventional binding method for low power in a
high-level synthesis mainly focuses on finding an optimal binding for
an assumed input data, and obtains only one binding table. In this
paper, we show that a binding method which uses multiple binding
tables gets better solution compared with the conventional methods
which use a single binding table, and propose a dynamic bus binding
scheme for low power using multiple binding tables. The proposed
method finds multiple binding tables for the proper partitions of an
input data, and switches binding tables dynamically to produce the
minimum total switching activity. Experimental result shows that the
proposed method obtains a binding solution having 12.6-28.9%
smaller total switching activity compared with the conventional
methods.
Abstract: Blood pulse is an important human physiological signal commonly used for the understanding of the individual physical health. Current methods of non-invasive blood pulse sensing require direct contact or access to the human skin. As such, the performances of these devices tend to vary with time and are subjective to human body fluids (e.g. blood, perspiration and skin-oil) and environmental contaminants (e.g. mud, water, etc). This paper proposes a simulation model for the novel method of non-invasive acquisition of blood pulse using the disturbance created by blood flowing through a localized magnetic field. The simulation model geometry represents a blood vessel, a permanent magnet, a magnetic sensor, surrounding tissues and air in 2-dimensional. In this model, the velocity and pressure fields in the blood stream are described based on Navier-Stroke equations and the walls of the blood vessel are assumed to have no-slip condition. The blood assumes a parabolic profile considering a laminar flow for blood in major artery near the skin. And the inlet velocity follows a sinusoidal equation. This will allow the computational software to compute the interactions between the magnetic vector potential generated by the permanent magnet and the magnetic nanoparticles in the blood. These interactions are simulated based on Maxwell equations at the location where the magnetic sensor is placed. The simulated magnetic field at the sensor location is found to assume similar sinusoidal waveform characteristics as the inlet velocity of the blood. The amplitude of the simulated waveforms at the sensor location are compared with physical measurements on human subjects and found to be highly correlated.