Abstract: Address Matching is an important application of
Geographic Information System (GIS). Prior to Address Matching
working, obtaining X,Y coordinates is necessary, which process is
calling Address Geocoding. This study will illustrate the effective
address geocoding process of using household registry database, and
the check system for geocoded address.
Abstract: Later marine propeller is the main component of ship
propulsion system. For a non-series propeller, it is difficult to
indicate the open water marine propeller performance without an
experimental study to measure the marine propeller parameters.
In the present study, the open water performance of a non-series
marine propeller has been carried out experimentally. The
geometrical aspects of a commercial non-series marine propeller
have been measured for a propeller blade area ratio of 0.3985. The
measured propeller performance parameters were the thrust and
torque coefficients for different propeller rotational speed and
different water channel flow velocity, then the open water
performance for the propeller has been plotted.
In addition, a direct comparison between the obtained
experimental results and a theoretical study of a B-series marine
propeller of the same blade area ratio has been carried out. A
correction factor has been introduced to apply the operating
conditions of the experimental results to that of the theoretical study
for the studied marine propeller.
Abstract: This research seeks to investigate the frequency and
profitability of index arbitrage opportunities involving the SET50
futures, SET50 component stocks, and the ThaiDEX SET50 ETF
(ticker symbol: TDEX). In particular, the frequency and profit of
arbitrage are measured in the following three arbitrage tests: (1)
SET50 futures vs. ThaiDEX SET50 ETF, (2) SET50 futures vs.
SET50 component stocks, and (3) ThaiDEX SET50 ETF vs. SET50
component stocks are investigated. For tests (2) and (3), the problems
involve conic optimization and quadratic programming as subproblems.
This research is first to apply conic optimization and
quadratic programming techniques in the context of index arbitrage
and is first to investigate such index arbitrage in the Thai equity and
derivatives markets. Thus, the contribution of this study is twofold.
First, its results would help understand the contribution of the
derivatives securities to the efficiency of the Thai markets. Second,
the methodology employed in this study can be applied to other
geographical markets, with minor adjustments.
Abstract: The use of a Geographic Information System (GIS) in
roadway lighting to show the state of street-lighting and nighttime
accident is demonstrated. Geographical maps were generated
showing colored streets based on how much of the street's length is
illuminated. The night to daytime accidents ratio at intersections
were found along with the state of lighting at those intersections.
The result is a method to show the state of street-lighting at roads and
intersections and a quick guide for decision makers to implement
strategies for better street-lighting to reduce night time traffic
accidents in a particular district.
Abstract: Geopolymer cement was evaluated as wellbore sealing material for carbon dioxide geosequestration application. Curing of cement system in saline water and strength testing in triaxial stress state condition under lateral confinement is relevant to primary cementing in CO2 geosequestration wellbore in saline aquifer. Geopolymer cement was cured in saline water (both at ambient conditions for 28 days and heated (60°C) conditions for 12 hours) and tested for triaxial strength at different levels of lateral confinement. Normal water and few other curing techniques were also studied both for geopolymer and API ‘G’ cement. Results reported were compared to evaluate the suitability of saline water for curing of geopolymer cement. Unconfined compression test results showed higher strength for curing in saline water than normal water. Besides, testing strength under lateral confinement demonstrated the material failure behavior from brittle to plastic.
Abstract: Pressure vessels are usually operating at temperatures
where the conditions of linear elastic fracture mechanics are no
longer met because massive plasticity precedes crack propagation. In
this work the development of a surface crack in a pressure vessel
subject to bending and tension under elastic-plastic fracture
mechanics conditions was investigated. Finite element analysis was
used to evaluate the hydrostatic stress, the J-integral and crack
growth for semi-elliptical surface-breaking cracks. The results
showed non-uniform stress triaxiality and crack driving force around
the crack front at large deformation levels. Different ductile crack
extensions were observed which emphasis the dependent of ductile
tearing on crack geometry and type of loading. In bending the crack
grew only beneath the surface, and growth was suppressed at the
deepest segment. This contrasts to tension where the crack breaks
through the thickness with uniform growth along the entire crack
front except at the free surface. Current investigations showed that
the crack growth developed under linear elastic fracture mechanics
conditions will no longer be applicable under ductile tearing
scenarios.
Abstract: In this paper, we propose a new architecture for the implementation of the N-point Fast Fourier Transform (FFT), based on the Radix-2 Decimation in Frequency algorithm. This architecture is based on a pipeline circuit that can process a stream of samples and produce two FFT transform samples every clock cycle. Compared to existing implementations the architecture proposed achieves double processing speed using the same circuit complexity.
Abstract: Today, incorrect use of lands and land use changes,
excessive grazing, no suitable using of agricultural farms, plowing on
steep slopes, road construct, building construct, mine excavation etc
have been caused increasing of soil erosion and sediment yield. For
erosion and sediment estimation one can use statistical and empirical
methods. This needs to identify land unit map and the map of
effective factors. However, these empirical methods are usually time
consuming and do not give accurate estimation of erosion. In this
study, we applied GIS techniques to estimate erosion and sediment of
Menderjan watershed at upstream Zayandehrud river in center of
Iran. Erosion faces at each land unit were defined on the basis of land
use, geology and land unit map using GIS. The UTM coordinates of
each erosion type that showed more erosion amounts such as rills and
gullies were inserted in GIS using GPS data. The frequency of
erosion indicators at each land unit, land use and their sediment yield
of these indices were calculated. Also using tendency analysis of
sediment yield changes in watershed outlet (Menderjan hydrometric
gauge station), was calculated related parameters and estimation
errors. The results of this study according to implemented watershed
management projects can be used for more rapid and more accurate
estimation of erosion than traditional methods. These results can also
be used for regional erosion assessment and can be used for remote
sensing image processing.
Abstract: The iris recognition technology is the most accurate,
fast and less invasive one compared to other biometric techniques
using for example fingerprints, face, retina, hand geometry, voice or
signature patterns. The system developed in this study has the
potential to play a key role in areas of high-risk security and can
enable organizations with means allowing only to the authorized
personnel a fast and secure way to gain access to such areas. The
paper aim is to perform the iris region detection and iris inner and
outer boundaries localization. The system was implemented on
windows platform using Visual C# programming language. It is easy
and efficient tool for image processing to get great performance
accuracy. In particular, the system includes two main parts. The first
is to preprocess the iris images by using Canny edge detection
methods, segments the iris region from the rest of the image and
determine the location of the iris boundaries by applying Hough
transform. The proposed system tested on 756 iris images from 60
eyes of CASIA iris database images.
Abstract: Australia, while being a large and eager consumer of
innovative and cutting edge Information and Communication
Technologies (ICT), continues to struggle to remain a leader in
Technological Innovation. This paper has two main contributions to
address certain aspects of this complex issue. The first being the
current findings of an ongoing research project on Information and
Innovation Management in the Australian Information and
Communication Technologies (ICT) sector. The major issues being
considered by the project include: investigation of the possible
inherent entrepreneurial nature of ICT; how to foster ICT innovation;
and examination of the inherent difficulties currently found within
the ICT industry of Australia in regards to supporting the
development of innovative and creative ideas. The second major
contribution is details of the I.-C.A.N. (Innovation by Collaborative
Anonymous Networking) software application information
management tool created and evolving in our research group. I-CAN,
besides having a positive reinforcement acronym, is aimed at
facilitating productive collaborative innovation in an Australian
workplace. Such a work environment is frequently subjected to
cultural influences such as the 'tall poppy syndrome' and 'negative'
or 'unconstructive' peer-pressure. There influences are frequently
seen as inhibitors to employee participation, entrepreneurship and
innovation.
Abstract: Vortex-shedding phenomenon of the flow
around combined two bodies having various geometries and sizes has been investigated experimentally in the Reynolds
number range between 4.1x103 and 1.75x104. To see the effect
of the rotation of the bodies on the vortex shedding, the
combined bodies were rotated from 0° to 180°. The combined models have a cross section composing of a main circular cylinder and an attached circular or square cylinder. Results
have shown that Strouhal numbers for two cases were
changed considerably with the angle of incidence, while it was found to be largely independent of Reynolds number at 150. Characteristics of the vortex formation region and
location of flow attachments, reattachments, and separations
were observed by means of the flow visualizations.
Depending on the inclination angle the effects of flow
attachment, separation and reattachment on vortex-shedding phenomenon have been discussed.
Abstract: Manufacturing tolerancing is intended to determine
the intermediate geometrical and dimensional states of the part
during its manufacturing process. These manufacturing dimensions
also serve to satisfy not only the functional requirements given in
the definition drawing, but also the manufacturing constraints, for
example geometrical defects of the machine, vibration and the
wear of the cutting tool. In this paper, an experimental study on the
influence of the wear of the cutting tool (systematic dispersions) is
explored. This study was carried out on three stages .The first stage
allows machining without elimination of dispersions (random,
systematic) so the tolerances of manufacture according to total
dispersions. In the second stage, the results of the first stage are
filtered in such way to obtain the tolerances according to random
dispersions. Finally, from the two previous stages, the systematic
dispersions are generated. The objective of this study is to model
by the least squares method the error of manufacture based on
systematic dispersion. Finally, an approach of optimization of the
manufacturing tolerances was developed for machining on a CNC
machine tool
Abstract: In construction of any structure, the aesthetic and utility values should be considered in such a way as to make the structure cost-effective. Most structures are composed of elements and joints which are very critical in any skeletal space structure because they majorly determine the performance of the structure. In early times, most space structures were constructed using rigid joints which had the advantage of better performing structures as compared to pin-jointed structures but with the disadvantage of requiring all the construction work to be done on site. The discovery of semi-rigid joints now enables connections to be prefabricated and quickly assembled on site while maintaining good performance. In this paper, cost-effective is discussed basing on strength of connectors at the joints, buckling of joints and overall structure, and the effect of initial geometrical imperfections. Several existing joints are reviewed by classifying them into categories and discussing where they are most suited and how they perform structurally. Also, finite element modeling using ABAQUS is done to determine the buckling behavior. It is observed that some joints are more economical than others. The rise to span ratio and imperfections are also found to affect the buckling of the structures. Based on these, general principles that guide the design of cost-effective joints and structures are discussed.
Abstract: This paper presents design and characterization of a
microaccelerometer designated for integration into cataract surgical
probe to detect hardness of different eye tissues during cataract
surgery. Soft posterior lens capsule of eye can be easily damaged in
comparison with hard opaque lens since the surgeon can not see
directly behind cutting needle during the surgery. Presence of
microsensor helps the surgeon to avoid rupturing posterior lens
capsule which if occurs leads to severe complications such as
glaucoma, infection, or even blindness. The microsensor having
overall dimensions of 480 μm x 395 μm is able to deliver significant
capacitance variations during encountered vibration situations which
makes it capable to distinguish between different types of tissue.
Integration of electronic components on chip ensures high level of
reliability and noise immunity while minimizes space and power
requirements. Physical characteristics and results on performance
testing, proves integration of microsensor as an effective tool to aid
the surgeon during this procedure.
Abstract: Based on statistics released by Islamic Republic of
Iran Police (IRIP), from among the total 9555 motorcycle accidents
that happened in 2007, 857 riders died and 11219 one got injured. If
we also consider the death toll and injuries of other vehicles'
accidents resulted from traffic violation by motorcycle riders, then
paying attention to the motorcycle accidents seems to be very
necessary. Therefore, in this study we tried to investigate the traits
and issues related to production, application, and training, along with
causes of motorcycle accidents from 4 perspectives of road, human,
environment and vehicle and also based on statistical and
geographical analysis of accident-sheets prepared by Iran Road
Patrol Department (IRPD). Unfamiliarity of riders with regulations
and techniques of motorcycling, disuse of safety equipments,
inefficiency of roads and design of junctions for safe trafficking of
motorcycles and finally the lack of sufficient control of responsible
organizations are among the major causes which lead to these
accidents.
Abstract: Limited infrastructure development on peats and
organic soils is a serious geotechnical issues common to many
countries of the world especially Malaysia which distributed 1.5 mill
ha of those problematic soil. These soils have high water content and
organic content which exhibit different mechanical properties and
may also change chemically and biologically with time. Constructing
structures on peaty ground involves the risk of ground failure and
extreme settlement. Nowdays, much efforts need to be done in
making peatlands usable for construction due to increased landuse.
Deep mixing method employing cement as binders, is generally used
as measure again peaty/ organic ground failure problem. Where the
technique is widely adopted because it can improved ground
considerably in a short period of time. An understanding of
geotechnical properties as shear strength, stiffness and compressibility
behavior of these soils was requires before continues construction on
it. Therefore, 1- 1.5 meter peat soil sample from states of Johor and
an organic soil from Melaka, Malaysia were investigated. Cement
were added to the soil in the pre-mixing stage with water cement ratio
at range 3.5,7,14,140 for peats and 5,10,30 for organic soils,
essentially to modify the original soil textures and properties. The
mixtures which in slurry form will pour to polyvinyl chloride (pvc)
tube and cured at room temperature 250C for 7,14 and 28 days.
Laboratory experiments were conducted including unconfined
compressive strength and bender element , to monitor the improved
strength and stiffness of the 'stabilised mixed soils'. In between,
scanning electron miscroscopic (SEM) were observations to
investigate changes in microstructures of stabilised soils and to
evaluated hardening effect of a peat and organic soils stabilised
cement. This preliminary effort indicated that pre-mixing peat and
organic soils contributes in gaining soil strength while help the
engineers to establish a new method for those problematic ground
improvement in further practical and long term applications.
Abstract: Monitoring of microbial flora in aquacultured sea bream, in relation to the physicochemical parameters of the rearing seawater, ended to a model describing the influence of the last to the quality of the fisheries. Fishes were sampled during eight months from four aqua farms in Western Greece and analyzed for psychrotrophic, H2S producing bacteria, Salmonella sp., heterotrophic plate count (PCA), with simultaneous physical evaluation. Temperature, dissolved oxygen, pH, conductivity, TDS, salinity, NO3 - and NH4 + ions were recorded. Temperature, dissolved oxygen and conductivity were correlated, respectively, to PCA, Pseudomonas sp. and Shewanella sp. counts. These parameters were the inputs of the model, which was driving, as outputs, to the prediction of PCA, Vibrio sp., Pseudomonas sp. and Shewanella sp. counts, and fish microbiological quality. The present study provides, for the first time, a ready-to-use predictive model of fisheries hygiene, leading to an effective management system for the optimization of aquaculture fisheries quality.
Abstract: Conventional approaches in the implementation of logic programming applications on embedded systems are solely of software nature. As a consequence, a compiler is needed that transforms the initial declarative logic program to its equivalent procedural one, to be programmed to the microprocessor. This approach increases the complexity of the final implementation and reduces the overall system's performance. On the contrary, presenting hardware implementations which are only capable of supporting logic programs prevents their use in applications where logic programs need to be intertwined with traditional procedural ones, for a specific application. We exploit HW/SW codesign methods to present a microprocessor, capable of supporting hybrid applications using both programming approaches. We take advantage of the close relationship between attribute grammar (AG) evaluation and knowledge engineering methods to present a programmable hardware parser that performs logic derivations and combine it with an extension of a conventional RISC microprocessor that performs the unification process to report the success or failure of those derivations. The extended RISC microprocessor is still capable of executing conventional procedural programs, thus hybrid applications can be implemented. The presented implementation is programmable, supports the execution of hybrid applications, increases the performance of logic derivations (experimental analysis yields an approximate 1000% increase in performance) and reduces the complexity of the final implemented code. The proposed hardware design is supported by a proposed extended C-language called C-AG.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: Twenty seven tektites from the Wenchang area, Hainan
province (south China) and five tektites from the Khon Kaen area
(northeast Thailand) were analyzed for major and trace element
contents and Rb-Sr isotopic compositions. All the samples studied are
splash-form tektites. Tektites of this study are characterized by high
SiO2 contents ranging from 71.95 to 74.07 wt% which is consistent
with previously published analyses of Australasian tektites. The trace
element ratios Ba/Rb (avg. 3.89), Th/Sm (avg. 2.40), Sm/Sc (avg.
0.45), Th/Sc (avg. 0.99) and the rare earth elements (REE) contents of
tektites of this study are similar to the average upper continental crust.
Based on the chemical composition, it is suggested that tektites in this
study are derived from similar parental material and are similar to the
post-Archean upper crustal rocks. The major and trace element
abundances of tektites analyzed indicate that the parental material of
tektites may be a terrestrial sedimentary deposit. The tektites from the
Wenchang area, Hainan Island have high positive εSr(0)
values-ranging from 184.5~196.5 which indicate that the parental
material for these tektites have similar Sr isotopic compositions to old
terrestrial sedimentary rocks and they were not dominantly derived
from recent young sediments (such as soil or loess). Based on Rb-Sr
isotopic data, it has been suggested by Blum (1992) [1]that the
depositional age of sedimentary target materials is close to 170Ma
(Jurassic). According to the model suggested by Ho and Chen
(1996)[2], mixing calculations for various amounts and combinations
of target rocks have been carried out. We consider that the best fit for
tektites from the Wenchang area is a mixture of 47% shale, 23%
sandstone, 25% greywacke and 5% quartzite, and the other tektites
from Khon Kaen area is a mixture of 46% shale, 2% sandstone, 20%
greywacke and 32% quartzite.