Abstract: An innovative tri-axes micro-power receiver is
proposed. The tri-axes micro-power receiver consists of two sets 3-D
micro-solenoids and one set planar micro-coils in which iron core is
embedded. The three sets of micro-coils are designed to be orthogonal
to each other. Therefore, no matter which direction the flux is present
along, the magnetic energy can be harvested and transformed into
electric power. Not only dead space of receiving power is mostly
reduced, but also transformation efficiency of electromagnetic energy
to electric power can be efficiently raised. By employing commercial
software, Ansoft Maxwell, the preliminary simulation results verify
that the proposed micro-power receiver can efficiently pick up the
energy transmitted by magnetic power source.
As to the fabrication process, the isotropic etching technique is
employed to micro-machine the inverse-trapezoid fillister so that the
copper wire can be successfully electroplated. The adhesion between
micro-coils and fillister is much enhanced.
Abstract: Mobile learning (m-learning) is a new method in teaching and learning process which combines technology of mobile device with learning materials. It can enhance student's engagement in learning activities and facilitate them to access the learning materials at anytime and anywhere. In Kolej Poly-Tech Mara (KPTM), this method is seen as an important effort in teaching practice and to improve student learning performance. The aim of this paper is to discuss the development of m-learning application called Mobile EEF Learning System (MEEFLS) to be implemented for Electric and Electronic Fundamentals course using Flash, XML (Extensible Markup Language) and J2ME (Java 2 micro edition). System Development Life Cycle (SDLC) was used as an application development approach. It has three modules in this application such as notes or course material, exercises and video. MEELFS development is seen as a tool or a pilot test for m-learning in KPTM.
Abstract: Fluorescent and WOLED are widely used because it consumes less energy. However, both lamps cause a harmonics because it has semiconductors components. Harmonic is a distorted sinusoidal electric wave and cause excess heat. This study compares the amount of harmonics generated by both lamps. The test shows that both lamps have THDv(Total Harmonics Distortion of Voltage) almost the same with average 2.5% while the average of WOLED's THDi(Total Harmonics Distortion of Current) is lower than fluorescent has. The average WOLED's THDi is 29.10 % and fluorescent's 'THDi is 87. 23 %.
Abstract: In this paper we discuss the behaviour of the longitudinal modes of a magnetized non collisional plasma subjected to an external electromagnetic field. We apply a semiclassical formalism, with the electrons being studied in a quantum mechanical viewpoint whereas the electromagnetic field in the classical context. We calculate the dielectric function in order to obtains the modes and found that, unlike the Bernstein modes, the presence of radiation induces oscillations around the cyclotron harmonics, which are smoothed as the energy stored in the radiation field becomes small compared to the thermal energy of the electrons. We analyze the influence of the number of photon involved in the electronic transitions between the Landau levels and how the parameters such as the external fields strength, plasma density and temperature affect the dispersion relation
Abstract: Ventricular fibrillation is a very important health
problem as is the cause of most of the sudden deaths in the world.
Waves of electrical activity are sent by the SA node, propagate
through the cardiac tissue and activate the mechanisms of cell
contraction, and therefore are responsible to pump blood to the body
harmonically. A spiral wave is an abnormal auto sustainable wave
that is responsible of certain types of arrhythmias. When these waves
break up, give rise to the fibrillation regime, in which there is a
complete loss in the coordination of the contraction of the heart
muscle. Interaction of spiral waves and obstacles is also of great
importance as it is believed that the attachment of a spiral wave to an
obstacle can provide with a transition of two different arrhythmias.
An obstacle can be partially excitable or non excitable. In this talk,
we present a numerical study of the interaction of meandering spiral
waves with partially and non excitable obstacles and focus on the
problem where the obstacle plays a fundamental role in the switch
between different spiral regimes, which represent different
arrhythmic regimes. Particularly, we study the phenomenon of
destabilization of spiral waves due to the presence of obstacles, a
phenomenon not completely understood (This work will appear as a
Chapter in a Book named Cardiac Arrhytmias by INTECH under the
name "Spiral Waves, Obstacles and Cardiac Arrhythmias", ISBN
979-953-307-050-5.).
Abstract: Piezoelectric transformers are electronic devices made
from piezoelectric materials. The piezoelectric transformers as the
name implied are used for changing voltage signals from one level to another. Electrical energy carried with signals is transferred by means of mechanical vibration. Characterizing in both electrical and
mechanical properties leads to extensively use and efficiency enhancement of piezoelectric transformers in various applications. In
this paper, study and analysis of electrical and mechanical properties of multi-layer piezoelectric transformers in forms of potential and
displacement distribution throughout the volume, respectively. This
paper proposes a set of quasi-static mathematical model of electromechanical
coupling for piezoelectric transformer by using a set of
partial differential equations. Computer-based simulation utilizing the three-dimensional finite element method (3-D FEM) is exploited
as a tool for visualizing potentials and displacements distribution
within the multi-layer piezoelectric transformer. This simulation was
conducted by varying a number of layers. In this paper 3, 5 and 7 of
the circular ring type were used. The computer simulation based on
the use of the FEM has been developed in MATLAB programming environment.
Abstract: The utilization of renewable energy sources in electric
power systems is increasing quickly because of public apprehensions
for unpleasant environmental impacts and increase in the energy
costs involved with the use of conventional energy sources. Despite
the application of these energy sources can considerably diminish the
system fuel costs, they can also have significant influence on the
system reliability. Therefore an appropriate combination of the
system reliability indices level and capital investment costs of system
is vital. This paper presents a hybrid wind/photovoltaic plant, with
the aim of supplying IEEE reliability test system load pattern while
the plant capital investment costs is minimized by applying a hybrid
particle swarm optimization (PSO) / harmony search (HS) approach,
and the system fulfills the appropriate level of reliability.
Abstract: Directional over current relays (DOCR) are commonly used in power system protection as a primary protection in distribution and sub-transmission electrical systems and as a secondary protection in transmission systems. Coordination of protective relays is necessary to obtain selective tripping. In this paper, an approach for efficiency reduction of DOCRs nonlinear optimum coordination (OC) is proposed. This was achieved by modifying the objective function and relaxing several constraints depending on the four constraints classification, non-valid, redundant, pre-obtained and valid constraints. According to this classification, the far end fault effect on the objective function and constraints, and in consequently on relay operating time, was studied. The study was carried out, firstly by taking into account the near-end and far-end faults in DOCRs coordination problem formulation; and then faults very close to the primary relays (nearend faults). The optimal coordination (OC) was achieved by simultaneously optimizing all variables (TDS and Ip) in nonlinear environment by using of Genetic algorithm nonlinear programming techniques. The results application of the above two approaches on 6-bus and 26-bus system verify that the far-end faults consideration on OC problem formulation don-t lose the optimality.
Abstract: In this paper spatial variability of some chemical and
physical soil properties were investigated in mountain rangelands of
Nesho, Mazandaran province, Iran. 110 soil samples from 0-30 cm
depth were taken with systematic method on grid 30×30 m2 in
regions with different vegetation cover and transported to laboratory.
Then soil chemical and physical parameters including Acidity (pH),
Electrical conductivity, Caco3, Bulk density, Particle density, total
phosphorus, total Nitrogen, available potassium, Organic matter,
Saturation moisture, Soil texture (percentage of sand, silt and clay),
Sodium, Calcium, magnesium were measured in laboratory. Data
normalization was performed then was done statistical analysis for
description of soil properties and geostatistical analysis for indication
spatial correlation between these properties and were perpetrated
maps of spatial distribution of soil properties using Kriging method.
Results indicated that in the study area Saturation moisture and
percentage of Sand had highest and lowest spatial correlation
respectively.
Abstract: In the present work, a study has been made on the combination of the electrical discharge machining (EDM) with ultrasonic vibrations to improve the machining efficiency. In experiments the graphite used as tool electrode and material of workpiece was AISIH13 tool steel. The parameters such as discharge peak current and pulse duration were changed to explore their effect on the material removal rate (MRR), relative tool wear ratio (TWR) and surface roughness. From the experimental result it can be seen that ultrasonic vibration of the workpiece can significantly reduces the inactive pulses and improves the stability of process. It was found that ultrasonic assisted EDM (US-EDM) is effective in attaining a high material removal rate (MRR) in finishing regime.
Abstract: Load forecasting has become in recent years one of the major areas of research in electrical engineering. Most traditional forecasting models and artificial intelligence neural network techniques have been tried out in this task. Artificial neural networks (ANN) have lately received much attention, and a great number of papers have reported successful experiments and practical tests. This article presents the development of an ANN-based short-term load forecasting model with improved generalization technique for the Regional Power Control Center of Saudi Electricity Company, Western Operation Area (SEC-WOA). The proposed ANN is trained with weather-related data and historical electric load-related data using the data from the calendar years 2001, 2002, 2003, and 2004 for training. The model tested for one week at five different seasons, typically, winter, spring, summer, Ramadan and fall seasons, and the mean absolute average error for one hour-ahead load forecasting found 1.12%.
Abstract: In this paper the development of neural network based fuzzy inference system for electricity consumption prediction is considered. The electricity consumption depends on number of factors, such as number of customers, seasons, type-s of customers, number of plants, etc. It is nonlinear process and can be described by chaotic time-series. The structure and algorithms of neuro-fuzzy system for predicting future values of electricity consumption is described. To determine the unknown coefficients of the system, the supervised learning algorithm is used. As a result of learning, the rules of neuro-fuzzy system are formed. The developed system is applied for predicting future values of electricity consumption of Northern Cyprus. The simulation of neuro-fuzzy system has been performed.
Abstract: Stability of functionally graded beams with piezoelectric layers subjected to axial compressive load that is simply supported at both ends is studied in this paper. The displacement field of beam is assumed based on first order shear deformation beam theory. Applying the Hamilton's principle, the governing equation is established. The influences of applied voltage, dimensionless geometrical parameter, functionally graded index and piezoelectric thickness on the critical buckling load of beam are presented. To investigate the accuracy of the present analysis, a compression study is carried out with a known data.
Abstract: In this paper, gate leakage current has been mitigated
by the use of novel nanoscale MOSFET with Source/Drain-to-Gate
Non-overlapped and high-k spacer structure for the first time. A
compact analytical model has been developed to study the gate
leakage behaviour of proposed MOSFET structure. The result
obtained has found good agreement with the Sentaurus Simulation.
Fringing gate electric field through the dielectric spacer induces
inversion layer in the non-overlap region to act as extended S/D
region. It is found that optimal Source/Drain-to-Gate Non-overlapped
and high-k spacer structure has reduced the gate leakage current to
great extent as compared to those of an overlapped structure. Further,
the proposed structure had improved off current, subthreshold slope
and DIBL characteristic. It is concluded that this structure solves the
problem of high leakage current without introducing the extra series
resistance.
Abstract: This paper presents an application of power line
carrier (PLC) for electrical power telemetering. This system has a
special capability of transmitting the measured values to a centralized
computer via power lines. The PLC modem as a passive high-pass
filter is designed for transmitting and receiving information. Its
function is to send the information carrier together with transmitted
data by superimposing it on the 50 Hz power frequency signal. A
microcontroller is employed to function as the main processing of the
modem. It is programmed for PLC control and interfacing with other
devices. Each power meter, connected via a PLC modem, is assigned
with a unique identification number (address) for distinguishing each
device from one another.
Abstract: n-CdO/p-Si heterojunction diode was fabricated using
sol-gel spin coating technique which is a low cost and easily scalable
method for preparing of semiconductor films. The structural and
morphological properties of CdO film were investigated. The X-ray
diffraction (XRD) spectra indicated that the film was of
polycrystalline nature. The scanning electron microscopy (SEM)
images indicate that the surface morphology CdO film consists of the
clusters formed with the coming together of the nanoparticles. The
electrical characterization of Au/n-CdO/p–Si/Al heterojunction diode
was investigated by current-voltage. The ideality factor of the diode
was found to be 3.02 for room temperature. The reverse current of
the diode strongly increased with illumination intensity of 100
mWcm-2 and the diode gave a maximum open circuit voltage Voc of
0.04 V and short-circuits current Isc of 9.92×10-9 A.
Abstract: This paper presents an environmental and technoeconomic
evaluation of light duty vehicles in Iran. A comprehensive
well-to-wheel (WTW) analysis is applied to compare different
automotive fuel chains, conventional internal combustion engines and
innovative vehicle powertrains. The study examines the
competitiveness of 15 various pathways in terms of energy
efficiencies, GHG emissions, and levelized cost of different energy
carriers. The results indicate that electric vehicles including battery
electric vehicles (BEV), fuel cell vehicles (FCV) and plug-in hybrid
electric vehicles (PHEV) increase the WTW energy efficiency by
54%, 51% and 46%, respectively, compared to common internal
combustion engines powered by gasoline. On the other hand,
greenhouse gas (GHG) emissions per kilometer of FCV and BEV
would be 48% lower than that of gasoline engines. It is concluded
that BEV has the lowest total cost of energy consumption and
external cost of emission, followed by internal combustion engines
(ICE) fueled by CNG. Conventional internal combustion engines
fueled by gasoline, on the other hand, would have the highest costs.
Abstract: Nowadays Multilevel inverters are widely using in various applications. Modulation strategy at fundamental switching frequency like, SHEPWM is prominent technique to eliminate lower order of harmonics with less switching losses and better harmonic profile. The equations which are formed by SHE are highly nonlinear transcendental in nature, there may exist single, multiple or even no solutions for a particular MI. However, some loads such as electrical drives, it is required to operate in whole range of MI. In order to solve SHE equations for whole range of MI, intelligent techniques are well suited to solve equations so as to produce lest %THDV. Hence, this paper uses Continuous genetic algorithm for minimising harmonics. This paper also presents wavelet based analysis of harmonics. The developed algorithm is simulated and %THD from FFT analysis and Wavelet analysis are compared. MATLAB programming environment and SIMULINK models are used whenever necessary.
Abstract: This paper presents the mathematical model of electric field and magnetic field in transmission system, which performs in second-order partial differential equation. This research has conducted analyzing the electromagnetic field radiating to atmosphere around the transmission line, when there is the transmission line transposition in case of long distance distribution. The six types of 500 kV transposed HV transmission line with double circuit will be considered. The computer simulation is applied finite element method that is developed by MATLAB program. The problem is considered to two dimensions, which is time harmonic system with the graphical performance of electric field and magnetic field. The impact from simulation of six types long distance distributing transposition will not effect changing of electric field and magnetic field which surround the transmission line.
Abstract: Even it has been recognized that Shape Memory
Alloys (SMA) have a significant potential for deployment actuators,
the number of applications of SMA-based actuators to the present
day is still quite small, due to the need of deep understanding of the
thermo-mechanical behavior of SMA, causing an important need for
a mathematical model able to describe all thermo-mechanical
properties of SMA by relatively simple final set of constitutive
equations. SMAs offer attractive potentials such as: reversible strains
of several percent, generation of high recovery stresses and high
power / weight ratios. The paper tries to provide an overview of the
shape memory functions and a presentation of the designed and
developed temperature control system used for a gripper actuated by
two pairs of differential SMA active springs. An experimental setup
was established, using electrical energy for actuator-s springs heating
process. As for holding the temperature of the SMA springs at certain
level for a long time was developed a control system in order to
avoid the active elements overheating.