Abstract: This paper was to study the clothes dryer using waste
heat from a split type air conditioner with a capacity of 12,648 btu/h.
The drying chamber had a minimum cross section area with the size
of 0.5 x 1.0 m2. The chamber was constructed by sailcloth and was
inside folded with aluminium foil. Then, it was connected to the
condensing unit of an air conditioner. The experiment was carried out
in two aspects which were the clothes drying with and without
auxiliary fan unit. The results showed that the drying rate of clothes
in the chamber installed with and without auxiliary fan unit were
2.26 and 1.1 kg/h, respectively. In case of the chamber installed with
a auxiliary fan unit, the additional power of 0.011 kWh was
consumed and the drying rate was higher than that of clothes drying
without auxiliary fan unit. Without auxiliary fan unit installation, no
energy was required but there was a portion of hot air leaks away
through the punctured holes at the wall of the drying chamber, hence
the drying rate was dropped below. The drying rate of clothes drying
using waste heat was higher than natural indoor drying and
commercial dryer which their drying rate were 0.17 and 1.9 kg/h,
respectively. It was noted that the COP of the air conditioner did not
change during the operating of clothes drying.
Abstract: The overlay approach has been widely used by many service providers for Traffic Engineering (TE) in large Internet backbones. In the overlay approach, logical connections are set up between edge nodes to form a full mesh virtual network on top of the physical topology. IP routing is then run over the virtual network. Traffic engineering objectives are achieved through carefully routing logical connections over the physical links. Although the overlay approach has been implemented in many operational networks, it has a number of well-known scaling issues. This paper proposes a new approach to achieve traffic engineering without full-mesh overlaying with the help of integrated approach and equal subset split method. Traffic engineering needs to determine the optimal routing of traffic over the existing network infrastructure by efficiently allocating resource in order to optimize traffic performance on an IP network. Even though constraint-based routing [1] of Multi-Protocol Label Switching (MPLS) is developed to address this need, since it is not widely tested or debugged, Internet Service Providers (ISPs) resort to TE methods under Open Shortest Path First (OSPF), which is the most commonly used intra-domain routing protocol. Determining OSPF link weights for optimal network performance is an NP-hard problem. As it is not possible to solve this problem, we present a subset split method to improve the efficiency and performance by minimizing the maximum link utilization in the network via a small number of link weight modifications. The results of this method are compared against results of MPLS architecture [9] and other heuristic methods.
Abstract: The purpose of this work is to establish the theoretical
foundations for calculating and designing the sublimationcondensation
processes in chemical apparatuses which are intended
for production of ultrafine powders of crystalline and amorphous
materials with controlled fractional composition. Theoretic analysis
of the primary processes of nucleation and growth kinetics of the
clusters according to the degree of super-saturation and the
homogeneous or heterogeneous nature of nucleation has been carried
out. The engineering design procedures of desublimation processes
have been offered and tested for modification of the Claus process.
Abstract: Tanzania secondary schools in rural areas are geographically and socially isolated, hence face a number of problems in getting learning materials resulting in poor performance in National examinations. E-learning as defined to be the use of information and communication technology (ICT) for supporting the educational processes has motivated Tanzania to apply ICT in its education system. There has been effort to improve secondary school education using ICT through several projects. ICT for e-learning to Tanzania rural secondary school is one of the research projects conceived by the University of Dar-es-Salaam through its College of Engineering and Technology. The main objective of the project is to develop a tool to enable ICT support rural secondary school. The project is comprehensive with a number of components, one being development of e-learning management system (e-LMS) for Tanzania secondary schools. This paper presents strategies of developing e-LMS. It shows the importance of integrating action research methodology with the modeling methods as presented by model driven architecture (MDA) and the usefulness of Unified Modeling Language (UML) on the issue of modeling. The benefit of MDA will go along with the development based on software development life cycle (SDLC) process, from analysis and requirement phase through design and implementation stages as employed by object oriented system analysis and design approach. The paper also explains the employment of open source code reuse from open source learning platforms for the context sensitive development of the e-LMS for Tanzania secondary schools.
Abstract: This paper presents a digital engineering library – the
Digital Mechanism and Gear Library, DMG-Lib – providing a multimedia collection of e-books, pictures, videos and animations in the domain of mechanisms and machines. The specific characteristic
about DMG-Lib is the enrichment and cross-linking of the different
sources. DMG-Lib e-books not only present pages as pixel images
but also selected figures augmented with interactive animations. The
presentation of animations in e-books increases the clearness of the
information.
To present the multimedia e-books and make them available in the
DMG-Lib internet portal a special e-book reader called StreamBook
was developed for optimal presentation of digitized books and to
enable reading the e-books as well as working efficiently and individually with the enriched information. The objective is to support different user tasks ranging from information retrieval to
development and design of mechanisms.
Abstract: The two cart inverted pendulum system is a good
bench mark for testing the performance of system dynamics and
control engineering principles. Devasia introduced this system to
study the asymptotic tracking problem for nonlinear systems. In this
paper the problem of asymptotic tracking of the two-cart with an
inverted-pendulum system to a sinusoidal reference inputs via
introducing a novel method for solving finite-horizon nonlinear
optimal control problems is presented. In this method, an iterative
method applied to state dependent Riccati equation (SDRE) to obtain
a reliable algorithm. The superiority of this technique has been shown
by simulation and comparison with the nonlinear approach.
Abstract: The use of computer hardware and software in
education and training dates to the early 1940s, when American
researchers developed flight simulators which used analog computers
to generate simulated onboard instrument data.Computer software is
widely used to help engineers and undergraduate student solve their
problems quickly and more accurately. This paper presents the list of
computer software in geotechnical engineering.
Abstract: Detection of human emotions has many potential applications. One of application is to quantify attentiveness audience in order evaluate acoustic quality in concern hall. The subjective audio preference that based on from audience is used. To obtain fairness evaluation of acoustic quality, the research proposed system for multimodal emotion detection; one modality based on brain signals that measured using electroencephalogram (EEG) and the second modality is sequences of facial images. In the experiment, an audio signal was customized which consist of normal and disorder sounds. Furthermore, an audio signal was played in order to stimulate positive/negative emotion feedback of volunteers. EEG signal from temporal lobes, i.e. T3 and T4 was used to measured brain response and sequence of facial image was used to monitoring facial expression during volunteer hearing audio signal. On EEG signal, feature was extracted from change information in brain wave, particularly in alpha and beta wave. Feature of facial expression was extracted based on analysis of motion images. We implement an advance optical flow method to detect the most active facial muscle form normal to other emotion expression that represented in vector flow maps. The reduce problem on detection of emotion state, vector flow maps are transformed into compass mapping that represents major directions and velocities of facial movement. The results showed that the power of beta wave is increasing when disorder sound stimulation was given, however for each volunteer was giving different emotion feedback. Based on features derived from facial face images, an optical flow compass mapping was promising to use as additional information to make decision about emotion feedback.
Abstract: In this paper, we evaluate the performance of the
Hybrid-MIMO Receiver Scheme (HMRS) in Cognitive Radio
network (CR-network). We investigate the efficiency of the proposed
scheme which the energy level and user number of primary user are
varied according to the characteristic of CR-network. HMRS can
allow users to transmit either Space-Time Block Code (STBC) or
Spatial-Multiplexing (SM) streams simultaneously by using
Successive Interference Cancellation (SIC) and Maximum Likelihood
Detection (MLD). From simulation, the results indicate that the
interference level effects to the performance of HMRS. Moreover,
the exact closed-form capacity of the proposed scheme is derived and
compared with STBC scheme.
Abstract: This paper focuses on the development of bond graph
dynamic model of the mechanical dynamics of an excavating mechanism
previously designed to be used with small tractors, which are
fabricated in the Engineering Workshops of Jomo Kenyatta University
of Agriculture and Technology. To develop a mechanical dynamics
model of the manipulator, forward recursive equations similar to
those applied in iterative Newton-Euler method were used to obtain
kinematic relationships between the time rates of joint variables
and the generalized cartesian velocities for the centroids of the
links. Representing the obtained kinematic relationships in bondgraphic
form, while considering the link weights and momenta as
the elements led to a detailed bond graph model of the manipulator.
The bond graph method was found to reduce significantly the number
of recursive computations performed on a 3 DOF manipulator for a
mechanical dynamic model to result, hence indicating that bond graph
method is more computationally efficient than the Newton-Euler
method in developing dynamic models of 3 DOF planar manipulators.
The model was verified by comparing the joint torque expressions
of a two link planar manipulator to those obtained using Newton-
Euler and Lagrangian methods as analyzed in robotic textbooks. The
expressions were found to agree indicating that the model captures
the aspects of rigid body dynamics of the manipulator. Based on
the model developed, actuator sizing and valve sizing methodologies
were developed and used to obtain the optimal sizes of the pistons
and spool valve ports respectively. It was found that using the pump
with the sized flow rate capacity, the engine of the tractor is able to
power the excavating mechanism in digging a sandy-loom soil.
Abstract: This paper is a part of research, in which the way the
biomedical engineers follow in their work is analyzed. The goal of
this paper is to present a method for specification of user
requirements in the medical devices maintenance process. Data
Gathering Methods, Research Model Phases and Descriptive
Analysis is presented. These technology and verification rules can be
implemented in Medical devices maintenance management process to
the maintenance process.
Abstract: The importance of good requirements engineering is well documented. Agile practices, promoting collaboration and communications, facilitate the elicitation and management of volatile requirements. However, current Agile practices work in a well-defined environment. It is necessary to have a co-located customer. With distributed development it is not always possible to realize this co-location. In this environment a suitable process, possibly supported by tools, is required to support changing requirements. This paper introduces the issues of concern when managing requirements in a distributed environment and describes work done at the Software Technology Research Centre as part of the NOMAD project.
Abstract: Decision support based upon risk analysis into
comparison of the electricity generation from different renewable
energy technologies can provide information about their effects on
the environment and society. The aim of this paper is to develop the
assessment framework regarding risks to health and environment,
and the society-s benefits of the electric power plant generation from
different renewable sources. The multicriteria framework to
multiattribute risk analysis technique and the decision analysis
interview technique are applied in order to support the decisionmaking
process for the implementing renewable energy projects to
the Bangkok case study. Having analyses the local conditions and
appropriate technologies, five renewable power plants are postulated
as options. As this work demonstrates, the analysis can provide a tool
to aid decision-makers for achieving targets related to promote
sustainable energy system.
Abstract: The ARMrayan Multimedia Mobile CMS (Content
Management System) is the first mobile CMS that gives the
opportunity to users for creating multimedia J2ME mobile
applications with their desired content, design and logo; simply,
without any need for writing even a line of code. The low-level
programming and compatibility problems of the J2ME, along with
UI designing difficulties, makes it hard for most people –even
programmers- to broadcast their content to the widespread mobile
phones used by nearly all people. This system provides user-friendly,
PC-based tools for creating a tree index of pages and inserting
multiple multimedia contents (e.g. sound, video and picture) in each
page for creating a J2ME mobile application. The output is a standalone
Java mobile application that has a user interface, shows texts
and pictures and plays music and videos regardless of the type of
devices used as long as the devices support the J2ME platform.
Bitmap fonts have also been used thus Middle Eastern languages can
be easily supported on all mobile phone devices. We omitted
programming concepts for users in order to simplify multimedia
content-oriented mobile applictaion designing for use in educational,
cultural or marketing centers. Ordinary operators can now create a
variety of multimedia mobile applications such as tutorials,
catalogues, books, and guides in minutes rather than months.
Simplicity and power has been the goal of this CMS. In this paper,
we present the software engineered-designed concepts of the
ARMrayan MCMS along with the implementation challenges faces
and solutions adapted.
Abstract: Nowadays, the increase of human population every
year results in increasing of water usage and demand. Saen Saep
canal is important canal in Bangkok. The main objective of this study
is using Artificial Neural Network (ANN) model to estimate the
Chemical Oxygen Demand (COD) on data from 11 sampling sites.
The data is obtained from the Department of Drainage and Sewerage,
Bangkok Metropolitan Administration, during 2007-2011. The
twelve parameters of water quality are used as the input of the
models. These water quality indices affect the COD. The
experimental results indicate that the ANN model provides a high
correlation coefficient (R=0.89).
Abstract: We have developed a distributed asynchronous Web
based training system. In order to improve the scalability and robustness
of this system, all contents and functions are realized on mobile
agents. These agents are distributed to computers, and they can use
a Peer to Peer network that modified Content-Addressable Network.
In the proposed system, only text data can be included in a exercise.
To make our proposed system more useful, the mechanism that it not
only adapts to multimedia data but also it doesn-t influence the user-s
learning even if the size of exercise becomes large is necessary.
Abstract: This study examined the effects of neuromuscular
training (NT) on limits of stability (LOS) in female individuals.
Twenty female basketball amateurs were assigned into NT
experimental group or control group by volunteer. All the players were
underwent regular basketball practice, 90 minutes, 3 times per week
for 6 weeks, but the NT experimental group underwent extra NT with
plyometric and core training, 50 minutes, 3 times per week for 6 weeks
during this period. Limits of stability (LOS) were evaluated by the
Biodex Balance System. One factor ANCOVA was used to examine
the differences between groups after training. The significant level for
statistic was set at p
Abstract: Knowledge modelling, a main activity for the development of Knowledge Based Systems, have no set standards and are mostly done in an ad hoc way. There is a lack of support for the transition from abstract level to implementation. In this paper, a methodology for the development of the knowledge model, which is inspired by both Software and Knowledge Engineering, is proposed. Use of UML which is the de-facto standard for modelling in the software engineering arena is explored for knowledge modelling. The methodology proposed, is used to develop a knowledge model of a knowledge based system for recommending suitable hotels for tourists visiting Mauritius.
Abstract: For fire safety purposes, the fire resistance and the
structural behavior of reinforced concrete members are assessed to
satisfy specific fire performance criteria. The available prescribed
provisions are based on standard fire load. Under various fire
scenarios, engineers are in need of both heat transfer analysis and
structural analysis. For heat transfer analysis, the study proposed a
modified finite difference method to evaluate the temperature profile
within a cross section. The research conducted is limited to concrete
sections exposed to a fire on their one side. The method is based on
the energy conservation principle and a pre-determined power
function of the temperature profile. The power value of 2.7 is found
to be a suitable value for concrete sections. The temperature profiles
of the proposed method are only slightly deviate from those of the
experiment, the FEM and the FDM for various fire loads such as
ASTM E 119, ASTM 1529, BS EN 1991-1-2 and 550 oC. The
proposed method is useful to avoid incontinence of the large matrix
system of the typical finite difference method to solve the
temperature profile. Furthermore, design engineers can simply apply
the proposed method in regular spreadsheet software.
Abstract: A novel direction-of-arrival (DOA) estimation technique, which uses a conventional multiple signal classification (MUSIC) algorithm with periodic signals, is applied to a single RF-port parasitic array antenna for direction finding. Simulation results show that the proposed method gives high resolution (1 degree) DOA estimation in an uncorrelated signal environment. The novelty lies in that the MUSIC algorithm is applied to a simplified antenna configuration. Only one RF port and one analogue-to-digital converter (ADC) are used in this antenna, which features low DC power consumption, low cost, and ease of fabrication. Modifications to the conventional MUSIC algorithm do not bring much additional complexity. The proposed technique is also free from the negative influence by the mutual coupling between elements. Therefore, the technique has great potential to be implemented into the existing wireless mobile communications systems, especially at the power consumption limited mobile terminals, to provide additional position location (PL) services.