Abstract: The present work attempts to investigate the
combustion, performance and emission characteristics of an existing
single-cylinder four-stroke compression-ignition engine operated in
dual-fuel mode with hydrogen as an alternative fuel. Environmental
concerns and limited amount of petroleum fuels have caused interests
in the development of alternative fuels like hydrogen for internal
combustion (IC) engines. In this experimental investigation, a diesel
engine is made to run using hydrogen in dual fuel mode with diesel,
where hydrogen is introduced into the intake manifold using an LPGCNG
injector and pilot diesel is injected using diesel injectors. A
Timed Manifold Injection (TMI) system has been developed to vary
the injection strategies. The optimized timing for the injection of
hydrogen was 10^0 CA after top dead center (ATDC). From the study
it was observed that with increasing hydrogen rate, enhancement in
brake thermal efficiency (BTHE) of the engine has been observed
with reduction in brake specific energy consumption (BSEC).
Furthermore, Soot contents decrease with an increase in indicated
specific NOx emissions with the enhancement of hydrogen flow rate.
Abstract: This paper presents effects of the mean operating
pressure on the optimal operating frequency based on temperature
differences across stack ends in a thermoacoustic refrigerator. In
addition to the length of the resonance tube, components of the
thermoacoustic refrigerator have an influence on the operating
frequency due to their acoustic properties, i.e., absorptivity,
reflectivity and transmissivity. The interference of waves incurs and
distorts the original frequency generated by the driver so that the
optimal operating frequency differs from the designs. These acoustic
properties are not parameters in the designs and be very complicated
to infer their responses. A prototype thermoacoustic refrigerator is
constructed and used to investigate its optimal operating frequency
compared to the design at various operating pressures. Helium and air
are used as working fluids during the experiments. The results
indicate that the optimal operating frequency of the prototype
thermoacoustic refrigerator using helium is at 6 bar and 490Hz or
approximately 20% away from the design frequency. The optimal
operating frequency at other mean pressures differs from the design
in an unpredictable manner, however, the optimal operating
frequency and pressure can be identified by testing.
Abstract: An innovative flooring underlayment was produced
and tested. The composite system is made of common OSB boards
and a layer of eco-friendly non-cement gypsum based material
(GeoGypTM). It was found that the shear bond between the two
materials is sufficient to secure the composite interaction between the
two. The very high compressive strength and relatively high tensile
strength of the non-cement based component together with its high
modulus of elasticity provides enough strength and stiffness for the
composite product to cover wider spacing between the joists. The
initial findings of this study indicate that with joist spacing as wide as
800 mm, the flooring system provides enough strength without
compromising the serviceability requirements of the building codes.
Abstract: We investigate relaxation dynamics of a quantum
dipole emitter (QDE), e.g., a molecule or quantum dot, located near a
metal nanoparticle (MNP) exhibiting a dipolar localized surface
plasmon (LSP) resonance at the frequency of the QDE radiative
transition. It is shown that under the condition of the QDE-MNP
characteristic relaxation time being much shorter than that of the
QDE in free-space but much longer than the LSP lifetime. It is also
shown that energy dissipation in the QDE-MNP system is relatively
weak with the probability of the photon emission being about 0.75, a
number which, rather surprisingly, does not explicitly depend on the
metal absorption characteristics. The degree of entanglement
measured by the concurrency takes the maximum value, while the
distances between the QDEs and metal ball approximately are equal.
Abstract: This paper presents the design and fabrication of an
optical window for an optical modulator toward image sensing
applications. An optical window consists of micrometer-order SiO2
capillaries (porous solid) that can modulate transmission light
intensity by moving the liquid in and out of porous solid. A high
optical transmittance of the optical window can be achieved due to
refractive index matching when the liquid is penetrated into the
porous solid. Otherwise, its light transmittance is lower because of
light reflection and scattering by air holes and capillary walls. Silicon
capillaries fabricated by deep reactive ion etching (DRIE) process are
completely oxidized to form the SiO2 capillaries. Therefore, high
aspect ratio SiO2 capillaries can be achieved based on silicon
capillaries formed by DRIE technique. Large compressive stress of
the oxide causes bending of the capillary structure, which is reduced
by optimizing the design of device structure. The large stress of the
optical window can be released via thin supporting beams. A 7.2 mm
x 9.6 mm optical window area toward a fully integrated with the
image sensor format is successfully fabricated and its optical
transmittance is evaluated with and without inserting liquids (ethanol
and matching oil). The achieved modulation range is approximately
20% to 35% with and without liquid penetration in visible region
(wavelength range from 450 nm to 650 nm).
Abstract: Flexible AC Transmission Systems (FACTS) is
granting a new group of advanced power electronic devices emerging
for enhancement of the power system performance. Unified Power
Flow Controller (UPFC) is a recent version of FACTS devices for
power system applications. The back-up energy supply system
incorporated with UPFC is providing a complete control of real and
reactive power at the same time and hence is competent to improve
the performance of an electrical power system. In this article, backup
energy supply unit such as superconducting magnetic energy storage
(SMES) is integrated with UPFC. In addition, comparative
exploration of UPFC–battery, UPFC–UC and UPFC–SMES
performance is evaluated through the vibrant simulation by using
MATLAB/Simulink software.
Abstract: The mechanisms underlying the association between
obesity and asthma may be related to a decreased immunological
tolerance induced by a defective function of regulatory T cells
(Tregs). The aim of this study is to establish the potential link
between these diseases and CD4+, CD25+ FoxP3+ Tregs as well as T
helper cells (Ths) in children. This is a prospective case control
study. Obese (n:40), asthmatic (n:40), asthmatic obese (n:40) and
healthy children (n:40), who don't have any acute or chronic diseases,
were included in this study. Obese children were evaluated according
to WHO criteria. Asthmatic patients were chosen based on GINA
criteria. Parents were asked to fill up the questionnaire. Informed
consent forms were taken. Blood samples were marked with CD4+,
CD25+ and FoxP3+ in order to determine Tregs and Ths by flow
cytometric method. Statistical analyses were performed. p≤0.05 was
chosen as meaningful threshold. Tregs exhibiting anti-inflammatory
nature were significantly lower in obese (0,16%; p≤0,001), asthmatic
(0,25%; p≤0,01) and asthmatic obese (0,29%; p≤0,05) groups than
the control group (0,38%). Ths were counted higher in asthma group
than the control (p≤0,01) and obese (p≤0,001) groups. T cell
immunity plays important roles in obesity and asthma pathogeneses.
Decreased numbers of Tregs found in obese, asthmatic and asthmatic
obese children may help to elucidate some questions in
pathophysiology of these diseases. For HOMA-IR levels, any
significant difference was not noted between control and obese
groups, but statistically higher values were found for obese
asthmatics. The values obtained in all groups were found to be below
the critical cut off points. This finding has made the statistically
significant difference observed between Tregs of obese, asthmatic,
obese asthmatic and control groups much more valuable. These
findings will be useful in diagnosis and treatment of these disorders
and future studies are needed. The production and propagation of
Tregs may be promising in alternative asthma and obesity treatments.
Abstract: Employer branding is considered as a useful tool for
addressing the global-local problem facing complex organisations
that have operations scattered across the globe and face challenges of
dealing with the local environment alongside. Despite being an
established field of study within the Western developed world, there
is little empirical evidence concerning the relevance of employer
branding to global companies that operate in the under-developed
economies. This paper fills this gap by gaining rich insight into the
implementation of employer branding programs in a foreign
multinational operating in Pakistan dealing with the global-local
problem. The study is qualitative in nature and employs semistructured
and focus group interviews with senior/middle managers
and local frontline employees to deeply examine the phenomenon in
case organisation. Findings suggest that authenticity is required in
employer brands to enable them to respond to the local needs thereby
leading to the resolution of the global-local problem. However, the
role of signaling theory is key to the development of authentic
employer brands as it stresses on the need to establish an efficient and
effective signaling environment where in signals travel in both
directions (from signal designers to receivers and backwards) and
facilitate firms with the global-local problem. The paper also
identifies future avenues of research for the employer branding field.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: The introduction of degradable plastic materials into
agricultural sectors has represented a promising alternative to
promote green agriculture and environmental friendly of modern
farming practices. Major challenges of developing degradable
agricultural films are to identify the most feasible types of
degradation mechanisms, composition of degradable polymers and
related processing techniques. The incorrect choice of degradable
mechanisms to be applied during the degradation process will cause
premature losses of mechanical performance and strength. In order to
achieve controlled process of agricultural film degradation, the
compositions of degradable agricultural film also important in order
to stimulate degradation reaction at required interval of time and to
achieve sustainability of the modern agricultural practices. A set of
photodegradable polyethylene based agricultural film was developed
and produced, following the selective optimization of processing
parameters of the agricultural film manufacturing system. Example of
agricultural films application for oil palm seedlings cultivation is
presented.
Abstract: In this paper, we introduced a gradient-based inverse
solver to obtain the missing boundary conditions based on the
readings of internal thermocouples. The results show that the method
is very sensitive to measurement errors, and becomes unstable when
small time steps are used. The artificial neural networks are shown to
be capable of capturing the whole thermal history on the run-out
table, but are not very effective in restoring the detailed behavior of
the boundary conditions. Also, they behave poorly in nonlinear cases
and where the boundary condition profile is different.
GA and PSO are more effective in finding a detailed
representation of the time-varying boundary conditions, as well as in
nonlinear cases. However, their convergence takes longer. A
variation of the basic PSO, called CRPSO, showed the best
performance among the three versions. Also, PSO proved to be
effective in handling noisy data, especially when its performance
parameters were tuned. An increase in the self-confidence parameter
was also found to be effective, as it increased the global search
capabilities of the algorithm. RPSO was the most effective variation
in dealing with noise, closely followed by CRPSO. The latter
variation is recommended for inverse heat conduction problems, as it
combines the efficiency and effectiveness required by these
problems.
Abstract: Co-crystal is believed to improve the solubility and
dissolution rates and thus, enhanced the bioavailability of poor water
soluble drugs particularly during the oral route of administration.
With the existing of poorly soluble drugs in pharmaceutical industry,
the screening of co-crystal formation using carbamazepine (CBZ) as
a model drug compound with dicarboxylic acids co-crystal formers
(CCF) namely fumaric (FA) and succinic (SA) acids in ethanol has
been studied. The co-crystal formations were studied by varying the
mol ratio values of CCF to CBZ to access the effect of CCF
concentration on the formation of the co-crystal. Solvent evaporation,
slurry and cooling crystallization which representing the solution
based method co-crystal screening were used. Based on the
differential scanning calorimetry (DSC) analysis, the melting point of
CBZ-SA in different ratio was in the range between 188oC-189oC.
For CBZ-FA form A and CBZ-FA form B the melting point in
different ratio were in the range of 174oC-175oC and 185oC-186oC
respectively. The product crystal from the screening was also
characterized using X-ray powder diffraction (XRPD). The XRPD
pattern profile analysis has shown that the CBZ co-crystals with FA
and SA were successfully formed for all ratios studied. The findings
revealed that CBZ-FA co-crystal were formed in two different
polymorphs. It was found that CBZ-FA form A and form B were
formed from evaporation and slurry crystallization methods
respectively. On the other hand, in cooling crystallization method,
CBZ-FA form A was formed at lower mol ratio of CCF to CBZ and
vice versa. This study disclosed that different methods and mol ratios
during the co-crystal screening can affect the outcome of co-crystal
produced such as polymorphic forms of co-crystal and thereof. Thus,
it was suggested that careful attentions is needed during the screening
since the co-crystal formation is currently one of the promising
approach to be considered in research and development for
pharmaceutical industry to improve the poorly soluble drugs.
Abstract: This paper presents development results of the method
of seismoacoustic activity monitoring based on usage vibrosensitive
properties of optical fibers. Analysis of Rayleigh backscattering
radiation parameters changes, which take place due to microscopic
seismoacoustic impacts on the optical fiber, allows to determine
seismoacoustic emission sources positions and to identify their types.
Results of using this approach are successful for complex monitoring
of railways.
Abstract: Rice husk and kenaf filled with calcium carbonate
(CaCO3) and high density polyethylene (HDPE) composite were
prepared separately using twin-screw extruder at 50rpm. Different
filler loading up to 30 parts of rice husk particulate and kenaf fiber
were mixed with the fixed 30% amount of CaCO3 mineral filler to
produce rice husk/CaCO3/HDPE and kenaf/CaCO3/HDPE hybrid
composites. In this study, the effects of natural fiber for both rice
husk and kenaf in CaCO3/HDPE composite on physical, mechanical
and morphology properties were investigated. Field Emission
Scanning Microscope (FeSEM) was used to investigate the impact
fracture surfaces of the hybrid composite. The property analyses
showed that water absorption increased with the presence of kenaf
and rice husk fillers. Natural fibers in composite significantly
influence water absorption properties due to natural characters of
fibers which contain cellulose, hemicellulose and lignin structures.
The result showed that 10% of additional natural fibers into hybrid
composite had caused decreased flexural strength, however additional
of high natural fiber (>10%) filler loading has proved to increase its
flexural strength.
Abstract: The arm length, hand length, hand breadth and middle
finger length of 1540 right-handed industrial workers of Haryana
state was used to assess the relationship between the upper limb
dimensions and stature. Initially, the data were analyzed using basic
univariate analysis and independent t-tests; then simple and multiple
linear regression models were used to estimate stature using SPSS
(version 17). There was a positive correlation between upper limb
measurements (hand length, hand breadth, arm length and middle
finger length) and stature (p < 0.01), which was highest for hand
length. The accuracy of stature prediction ranged from ± 54.897 mm
to ± 58.307 mm. The use of multiple regression equations gave better
results than simple regression equations. This study provides new
forensic standards for stature estimation from the upper limb
measurements of male industrial workers of Haryana (India). The
results of this research indicate that stature can be determined using
hand dimensions with accuracy, when only upper limb is available
due to any reasons likewise explosions, train/plane crashes, mutilated
bodies, etc. The regression formula derived in this study will be
useful for anatomists, archaeologists, anthropologists, design
engineers and forensic scientists for fairly prediction of stature using
regression equations.
Abstract: Today’s VLSI networks demands for high speed. And
in this work the compact form mathematical model for current mode
signalling in VLSI interconnects is presented.RLC interconnect line
is modelled using characteristic impedance of transmission line and
inductive effect. The on-chip inductance effect is dominant at lower
technology node is emulated into an equivalent resistance. First order
transfer function is designed using finite difference equation, Laplace
transform and by applying the boundary conditions at the source and
load termination. It has been observed that the dominant pole
determines system response and delay in the proposed model. The
novel proposed current mode model shows superior performance as
compared to voltage mode signalling. Analysis shows that current
mode signalling in VLSI interconnects provides 2.8 times better
delay performance than voltage mode. Secondly the damping factor
of a lumped RLC circuit is shown to be a useful figure of merit.
Abstract: Using the first-principles full-potential linearized
augmented plane wave plus local orbital (FP-LAPW+lo) method
based on density functional theory (DFT), we have investigated the
electronic structure and magnetism of full Heusler alloys Co2ZrGe
and Co2NbB. These compounds are predicted to be half-metallic
ferromagnets (HMFs) with a total magnetic moment of 2.000 B per
formula unit, well consistent with the Slater-Pauling rule.
Calculations show that both the alloys have an indirect band gaps, in
the minority-spin channel of density of states (DOS), with values of
0.58 eV and 0.47 eV for Co2ZrGe and Co2NbB, respectively.
Analysis of the DOS and magnetic moments indicates that their
magnetism is mainly related to the d-d hybridization between the Co
and Zr (or Nb) atoms. The half-metallicity is found to be relatively
robust against volume changes. In addition, an atom inside molecule
AIM formalism and an electron localization function ELF were also
adopted to study the bonding properties of these compounds, building
a bridge between their electronic and bonding behavior.
As they have a good crystallographic compatibility with the lattice of
semiconductors used industrially and negative calculated cohesive
energies with considerable absolute values these two alloys could be
promising magnetic materials in the spintronic field.
Abstract: Corrosion of concrete sewer pipes induced by sulfuric
acid is an acknowledged problem and a ticking time-bomb to sewer
operators. Whilst the chemical reaction of the corrosion process is
well-understood, the indirect roles of other parameters in the
corrosion process which are found in sewer environment are not
highly reflected on. This paper reports on a field studies undertaken
in Austria and United Kingdom, where the parameters of
temperature, pH, H2S and CO2 were monitored over a period of time.
The study establishes that (i) effluent temperature and pH have
similar daily pattern and peak times, when examined in minutes
scale; (ii) H2S and CO2 have an identical hourly pattern; (iii) H2S
instant or shifted relation to effluent temperature is governed by the
root mean square value of CO2.
Abstract: In recent years parasitic antenna play major role in
MIMO systems because of their gain and spectral efficiency. In this
paper, single RF chain MIMO transmitter is designed using
reconfigurable parasitic antenna. The Spatial Modulation (SM) is a
recently proposed scheme in MIMO scenario which activates only
one antenna at a time. The SM entirely avoids ICI and IAS, and only
requires a single RF chain at the transmitter. This would switch ON a
single transmit-antenna for data transmission while all the other
antennas are kept silent. The purpose of the parasitic elements is to
change the radiation pattern of the radio waves which is emitted from
the driven element and directing them in one direction and hence
introduces transmit diversity. Diode is connect between the patch and
ground by changing its state (ON and OFF) the parasitic element act
as reflector and director and also capable of steering azimuth and
elevation angle. This can be achieved by changing the input
impedance of each parasitic element through single RF chain. The
switching of diode would select the single parasitic antenna for
spatial modulation. This antenna is expected to achieve maximum
gain with desired efficiency.
Abstract: We have been grouping and developing various kinds
of practical, promising sensing applied systems concerning
agricultural advancement and technical tradition (guidance). These
include advanced devices to secure real-time data related to worker
motion, and we analyze by methods of various advanced statistics and
human dynamics (e.g. primary component analysis, Ward system
based cluster analysis, and mapping). What is more, we have been
considering worker daily health and safety issues. Targeted fields are
mainly common farms, meadows, and gardens. After then, we
observed and discussed time-line style, changing data. And, we made
some suggestions. The entire plan makes it possible to improve both
the aforementioned applied systems and farms.