Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: This paper tries to represent a new method for
computing the reliability of a system which is arranged in series or
parallel model. In this method we estimate life distribution function
of whole structure using the asymptotic Extreme Value (EV)
distribution of Type I, or Gumbel theory. We use EV distribution in
minimal mode, for estimate the life distribution function of series
structure and maximal mode for parallel system. All parameters also
are estimated by Moments method. Reliability function and failure
(hazard) rate and p-th percentile point of each function are
determined. Other important indexes such as Mean Time to Failure
(MTTF), Mean Time to repair (MTTR), for non-repairable and
renewal systems in both of series and parallel structure will be
computed.
Abstract: This paper presents the development of an electricity simulation model taking into account electrical network constraints, applied on the Belgian power system. The base of the model is optimizing an extensive Unit Commitment (UC) problem through the use of Mixed Integer Linear Programming (MILP). Electrical constraints are incorporated through the implementation of a DC load flow. The model encloses the Belgian power system in a 220 – 380 kV high voltage network (i.e., 93 power plants and 106 nodes). The model features the use of pumping storage facilities as well as the inclusion of spinning reserves in a single optimization process. Solution times of the model stay below reasonable values.
Abstract: This paper focuses on testing database of existing
information system. At the beginning we describe the basic problems
of implemented databases, such as data redundancy, poor design of
database logical structure or inappropriate data types in columns of
database tables. These problems are often the result of incorrect
understanding of the primary requirements for a database of an
information system. Then we propose an algorithm to compare the
conceptual model created from vague requirements for a database
with a conceptual model reconstructed from implemented database.
An algorithm also suggests steps leading to optimization of
implemented database. The proposed algorithm is verified by an
implemented prototype. The paper also describes a fuzzy system
which works with the vague requirements for a database of an
information system, procedure for creating conceptual from vague
requirements and an algorithm for reconstructing a conceptual model
from implemented database.
Abstract: Modern managements of water distribution system
(WDS) need water quality models that are able to accurately predict
the dynamics of water quality variations within the distribution system
environment. Before water quality models can be applied to solve
system problems, they should be calibrated. Although former
researchers use GA solver to calibrate relative parameters, it is
difficult to apply on the large-scale or medium-scale real system for
long computational time. In this paper a new method is designed
which combines both macro and detailed model to optimize the water
quality parameters. This new combinational algorithm uses radial
basis function (RBF) metamodeling as a surrogate to be optimized for
the purpose of decreasing the times of time-consuming water quality
simulation and can realize rapidly the calibration of pipe wall reaction
coefficients of chlorine model of large-scaled WDS. After two cases
study this method is testified to be more efficient and promising, and
deserve to generalize in the future.
Abstract: This paper includes a review of three physics simulation packages that can be used to provide researchers with a virtual ground for modeling, implementing and simulating complex models, as well as testing their control methods with less cost and time of development. The inverted pendulum model was used as a test bed for comparing ODE, DANCE and Webots, while Linear State Feedback was used to control its behavior. The packages were compared with respect to model creation, solving systems of differential equation, data storage, setting system variables, control the experiment and ease of use. The purpose of this paper is to give an overview about our experience with these environments and to demonstrate some of the benefits and drawbacks involved in practice for each package.
Abstract: The paper proposes a new concept in developing
collaborative design system. The concept framework involves
applying simulation of supply chain management to collaborative
design called – 'SCM–Based Design Tool'. The system is developed
particularly to support design activities and to integrate all facilities
together. The system is aimed to increase design productivity and
creativity. Therefore, designers and customers can collaborate by the
system since conceptual design. JAG: Jewelry Art Generator based
on artificial intelligence techniques is integrated into the system.
Moreover, the proposed system can support users as decision tool
and data propagation. The system covers since raw material supply
until product delivery. Data management and sharing information are
visually supported to designers and customers via user interface. The
system is developed on Web–assisted product development
environment. The prototype system is presented for Thai jewelry
industry as a system prototype demonstration, but applicable for
other industry.
Abstract: This paper reports work done to improve the modeling of complex processes when only small experimental data sets are available. Neural networks are used to capture the nonlinear underlying phenomena contained in the data set and to partly eliminate the burden of having to specify completely the structure of the model. Two different types of neural networks were used for the application of pulping problem. A three layer feed forward neural networks, using the Preconditioned Conjugate Gradient (PCG) methods were used in this investigation. Preconditioning is a method to improve convergence by lowering the condition number and increasing the eigenvalues clustering. The idea is to solve the modified odified problem M-1 Ax= M-1b where M is a positive-definite preconditioner that is closely related to A. We mainly focused on Preconditioned Conjugate Gradient- based training methods which originated from optimization theory, namely Preconditioned Conjugate Gradient with Fletcher-Reeves Update (PCGF), Preconditioned Conjugate Gradient with Polak-Ribiere Update (PCGP) and Preconditioned Conjugate Gradient with Powell-Beale Restarts (PCGB). The behavior of the PCG methods in the simulations proved to be robust against phenomenon such as oscillations due to large step size.
Abstract: 3-hydroxy-3-methylglutaryl coenzyme A reductase (HMGR) catalyzes the conversion of HMG-CoA to mevalonate using NADPH and the enzyme is involved in rate-controlling step of mevalonate. Inhibition of HMGR is considered as effective way to lower cholesterol levels so it is drug target to treat hypercholesterolemia, major risk factor of cardiovascular disease. To discover novel HMGR inhibitor, we performed structure-based pharmacophore modeling combined with molecular dynamics (MD) simulation. Four HMGR inhibitors were used for MD simulation and representative structure of each simulation were selected by clustering analysis. Four structure-based pharmacophore models were generated using the representative structure. The generated models were validated used in virtual screening to find novel scaffolds for inhibiting HMGR. The screened compounds were filtered by applying drug-like properties and used in molecular docking. Finally, four hit compounds were obtained and these complexes were refined using energy minimization. These compounds might be potential leads to design novel HMGR inhibitor.
Abstract: In this paper we propose a computational model for the representation and processing of morpho-phonological phenomena in a natural language, like Modern Greek. We aim at a unified treatment of inflection, compounding, and word-internal phonological changes, in a model that is used for both analysis and generation. After discussing certain difficulties cuase by well-known finitestate approaches, such as Koskenniemi-s two-level model [7] when applied to a computational treatment of compounding, we argue that a morphology-based model provides a more adequate account of word-internal phenomena. Contrary to the finite state approaches that cannot handle hierarchical word constituency in a satisfactory way, we propose a unification-based word grammar, as the nucleus of our strategy, which takes into consideration word representations that are based on affixation and [stem stem] or [stem word] compounds. In our formalism, feature-passing operations are formulated with the use of the unification device, and phonological rules modeling the correspondence between lexical and surface forms apply at morpheme boundaries. In the paper, examples from Modern Greek illustrate our approach. Morpheme structures, stress, and morphologically conditioned phoneme changes are analyzed and generated in a principled way.
Abstract: Many exist studies always use Markov decision
processes (MDPs) in modeling optimal route choice in
stochastic, time-varying networks. However, taking many
variable traffic data and transforming them into optimal route
decision is a computational challenge by employing MDPs in
real transportation networks. In this paper we model finite
horizon MDPs using directed hypergraphs. It is shown that the
problem of route choice in stochastic, time-varying networks
can be formulated as a minimum cost hyperpath problem, and
it also can be solved in linear time. We finally demonstrate the
significant computational advantages of the introduced
methods.
Abstract: Physical education (PE) is still neglected in schools
despite its academic, social, psychological, and health benefits.
Based on the assumption that Information and Communication
Technologies (ICTs) can contribute to the development of PE in
schools, this study aims to design a model of the factors affecting the
adoption of ICTs for PE in schools. The proposed model is based on
a sound theoretical framework. It was designed following a literature
review of technology adoption theories and of ICT adoption factors
for physical education. The technology adoption model that fitted to
the best all ICT adoption factors was then chosen as the basis for the
proposed model. It was found that the Unified Theory of Acceptance
and Use of Technology (UTAUT) is the most adequate theoretical
framework for the modeling of ICT adoption factors for physical
education.
Abstract: A novel PDE solver using the multidimensional wave
digital filtering (MDWDF) technique to achieve the solution of a 2D
seismic wave system is presented. In essence, the continuous physical
system served by a linear Kirchhoff circuit is transformed to an
equivalent discrete dynamic system implemented by a MD wave
digital filtering (MDWDF) circuit. This amounts to numerically
approximating the differential equations used to describe elements of a
MD passive electronic circuit by a grid-based difference equations
implemented by the so-called state quantities within the passive
MDWDF circuit. So the digital model can track the wave field on a
dense 3D grid of points. Details about how to transform the continuous
system into a desired discrete passive system are addressed. In
addition, initial and boundary conditions are properly embedded into
the MDWDF circuit in terms of state quantities. Graphic results have
clearly demonstrated some physical effects of seismic wave (P-wave
and S–wave) propagation including radiation, reflection, and
refraction from and across the hard boundaries. Comparison between
the MDWDF technique and the finite difference time domain (FDTD)
approach is also made in terms of the computational efficiency.
Abstract: Long term rainfall analysis and prediction is a
challenging task especially in the modern world where the impact of
global warming is creating complications in environmental issues.
These factors which are data intensive require high performance
computational modeling for accurate prediction. This research paper
describes a prototype which is designed and developed on grid
environment using a number of coupled software infrastructural
building blocks. This grid enabled system provides the demanding
computational power, efficiency, resources, user-friendly interface,
secured job submission and high throughput. The results obtained
using sequential execution and grid enabled execution shows that
computational performance has enhanced among 36% to 75%, for
decade of climate parameters. Large variation in performance can be
attributed to varying degree of computational resources available for
job execution.
Grid Computing enables the dynamic runtime selection, sharing
and aggregation of distributed and autonomous resources which plays
an important role not only in business, but also in scientific
implications and social surroundings. This research paper attempts to
explore the grid enabled computing capabilities on weather indices
from HOAPS data for climate impact modeling and change
detection.
Abstract: A key to success of high quality software development
is to define valid and feasible requirements specification. We have
proposed a method of model-driven requirements analysis using
Unified Modeling Language (UML). The main feature of our method
is to automatically generate a Web user interface mock-up from UML
requirements analysis model so that we can confirm validity of
input/output data for each page and page transition on the system by
directly operating the mock-up. This paper proposes a support method
to check the validity of a data life cycle by using a model checking tool
“UPPAAL" focusing on CRUD (Create, Read, Update and Delete).
Exhaustive checking improves the quality of requirements analysis
model which are validated by the customers through automatically
generated mock-up. The effectiveness of our method is discussed by a
case study of requirements modeling of two small projects which are a
library management system and a supportive sales system for text
books in a university.
Abstract: Knowledge development in companies relies on
knowledge-intensive business processes, which are characterized by
a high complexity in their execution, weak structuring,
communication-oriented tasks and high decision autonomy, and often the need for creativity and innovation. A foundation of knowledge development is provided, which is based on a new conception of
knowledge and knowledge dynamics. This conception consists of a three-dimensional model of knowledge with types, kinds and qualities. Built on this knowledge conception, knowledge dynamics is
modeled with the help of general knowledge conversions between
knowledge assets. Here knowledge dynamics is understood to cover
all of acquisition, conversion, transfer, development and usage of
knowledge. Through this conception we gain a sound basis for
knowledge management and development in an enterprise. Especially
the type dimension of knowledge, which categorizes it according to
its internality and externality with respect to the human being, is crucial for enterprise knowledge management and development,
because knowledge should be made available by converting it to
more external types.
Built on this conception, a modeling approach for knowledgeintensive
business processes is introduced, be it human-driven,e-driven or task-driven processes. As an example for this approach, a model of the creative activity for the renewal planning of
a product is given.
Abstract: This paper analytically investigates the 3D flow
pattern at the confluences of two rectangular channels having 900
angles using Navier-Stokes equations based on Reynolds Stress
Turbulence Model (RSM). The equations are solved by the Finite-
Volume Method (FVM) and the flow is analyzed in terms of steadystate
(single-phased) conditions. The Shumate experimental findings
were used to test the validity of data. Comparison of the simulation
model with the experimental ones indicated a close proximity
between the flow patterns of the two sets. Effects of the discharge
ratio on separation zone dimensions created in the main-channel
downstream of the confluence indicated an inverse relation, where a
decrease in discharge ratio, will entail an increase in the length and
width of the separation zone. The study also found the model as a
powerful analytical tool in the feasibility study of hydraulic
engineering projects.
Abstract: In this study, a synthetic pathway was created by
assembling genes from Clostridium butyricum and Escherichia coli
in different combinations. Among the genes were dhaB1 and dhaB2
from C. butyricum VPI1718 coding for glycerol dehydratase (GDHt)
and its activator (GDHtAc), respectively, involved in the conversion
of glycerol to 3-hydroxypropionaldehyde (3-HPA). The yqhD gene
from E.coli BL21 was also included which codes for an NADPHdependent
1,3-propanediol oxidoreductase isoenzyme (PDORI)
reducing 3-HPA to 1,3-propanediol (1,3-PD). Molecular modeling
analysis indicated that the conformation of fusion protein of YQHD
and DHAB1 was favorable for direct molecular channeling of the
intermediate 3-HPA. According to the simulation results, the yqhD
and dhaB1 gene were assembled in the upstream of dhaB2 to express
a fusion protein, yielding the recombinant strain E. coliBL21
(DE3)//pET22b+::yqhD-dhaB1_dhaB2 (strain BP41Y3). Strain
BP41Y3 gave 10-fold higher 1,3-PD concentration than E. coliBL21
(DE3)//pET22b+::yqhD-dhaB1_dhaB2 (strain BP31Y2) expressing
the recombinant enzymes simultaneously but in a non-fusion mode.
This is the first report using a gene fusion approach to enhance the
biological conversion of glycerol to the value added compound 1,3-
PD.
Abstract: “Web of Trust" is one of the recognized goals for
Web 2.0. It aims to make it possible for the people to take
responsibility for what they publish on the web, including
organizations, businesses and individual users. These objectives,
among others, drive most of the technologies and protocols recently
standardized by the governing bodies. One of the great advantages of
Web infrastructure is decentralization of publication. The primary
motivation behind Web 2.0 is to assist the people to add contents for
Collective Intelligence (CI) while providing mechanisms to link
content with people for evaluations and accountability of
information. Such structure of contents will interconnect users and
contents so that users can use contents to find participants and vice
versa. This paper proposes conceptual information storage and
linking model, based on decentralized information structure, that
links contents and people together. The model uses FOAF, Atom,
RDF and RDFS and can be used as a blueprint to develop Web 2.0
applications for any e-domain. However, primary target for this
paper is online trust evaluation domain. The proposed model targets
to assist the individuals to establish “Web of Trust" in online trust
domain.
Abstract: This paper describes a computer-aided design for
design of the concave globoidal cam with cylindrical rollers and
swinging follower. Four models with different modeling methods are
made from the same input data. The input data are angular input and
output displacements of the cam and the follower and some other
geometrical parameters of the globoidal cam mechanism. The best
cam model is the cam which has no interference with the rollers
when their motions are simulated in assembly conditions. The
angular output displacement of the follower for the best cam is also
compared with that of in the input data to check errors. In this study,
Pro/ENGINEER® Wildfire 2.0 is used for modeling the cam,
simulating motions and checking interference and errors of the
system.