Abstract: Concrete pavement has superior durability and longer
structural life than asphalt pavement. Concrete pavement requires
less maintenance compared to asphalt pavement which requires maintenance and major rehabilitation. Use of the concrete pavement
has been grown over the past decade in developing countries. Fibre reinforced concrete (FRC) has been successfully used in design of concrete pavement in past decade. In this research, the effect of fibre
volume fraction in modulus of rupture, load-deflection, equivalent flexural strength (fe,3) and the equivalent flexural strength ratio (Re,3)
has been used in different fibre volume fraction. Crimped-type flat
steel fibre of size 50 x 2.0 x 0.6 mm was used with 1.0%, 1.5% and 2.0% volume fraction. Beam specimens of size 500 x 100 x 100 mm were used for flexural as well as with JCI method for analysis flexural toughness, equivalent flexural strength. It was obtained as the 2% fibre volume fractions; reduce 45% of the concrete pavement
thickness.
Abstract: In this paper, the effect of bolt clamping force on the fatigue behavior of bolted single lap joints of aluminum alloy 2024- T3 have been studied using numerical finite element method. To do so, a three dimensional model according to the bolted single lap joint has been created and numerical analysis has been carried out using finite element based package. Then the stress distribution and also the slip amplitudes have been calculated in the critical regions and the outcome have been compared with the available experimental fatigue tests results. The numerical results show that in low applied clamping force, the fatigue failure of the specimens occur around the stress concentration location (the bolted hole edge) due to the tensile stresses and thus fatigue crack propagation, but with increase of the clamping force, the fatigue life increases and the cracks nucleate and propagate far from the hole edge because of fretting fatigue. In other words, with the further increase of clamping force value of the joint, the fatigue life reduces due to occurrence of the fretting fatigue in the critical location where the slip amplitude is within its critical occurs earlier.
Abstract: Background: Blunt aortic trauma (BAT) includes
various morphological changes that occur during deceleration,
acceleration and/or body compression in traffic accidents. The
various forms of BAT, from limited laceration of the intima to
complete transection of the aorta, depends on the force acting on the
vessel wall and the tolerance of the aorta to injury. The force depends
on the change in velocity, the dynamics of the accident and of the
seating position in the car. Tolerance to aortic injury depends on the
anatomy, histological structure and pathomorphological alterations
due to aging or disease of the aortic wall.
An overview of the literature and medical documentation reveals
that different terms are used to describe certain forms of BAT, which
can lead to misinterpretation of findings or diagnoses. We therefore,
propose a classification that would enable uniform systematic
screening of all forms of BAT. We have classified BAT into three
morphologycal types: TYPE I (intramural), TYPE II (transmural) and
TYPE III (multiple) aortic ruptures with appropriate subtypes.
Methods: All car accident casualties examined at the Institute of
Forensic Medicine from 2001 to 2009 were included in this
retrospective study. Autopsy reports were used to determine the
occurrence of each morphological type of BAT in deceased drivers,
front seat passengers and other passengers in cars and to define the
morphology of BAT in relation to the accident dynamics and the age
of the fatalities.
Results: A total of 391 fatalities in car accidents were included in
the study. TYPE I, TYPE II and TYPE III BAT were observed in
10,9%, 55,6% and 33,5%, respectively. The incidence of BAT in
drivers, front seat and other passengers was 36,7%, 43,1% and
28,6%, respectively. In frontal collisions, the incidence of BAT was
32,7%, in lateral collisions 54,2%, and in other traffic accidents
29,3%. The average age of fatalities with BAT was 42,8 years and of
those without BAT 39,1 years.
Conclusion: Identification and early recognition of the risk factors
of BAT following a traffic accident is crucial for successful treatment
of patients with BAT. Front seat passengers over 50 years of age who
have been injured in a lateral collision are the most at risk of BAT.
Abstract: A brushless DC motor with integrated drive circuit for air management system is presented. Using magnetic equivalent circuit model a basic design of the motor is determined, and specific configurations are inspected thanks to finite element analysis. In order to reduce an unbalanced magnetic force in an axial direction, induced forces between a stator core and a permanent magnet are calculated with respect to the relative positions of them. For the high efficiency, and high power density, BLDC motor and drive are developed. Also vibration mode and eccentricity of a rotor are considered at the rated and maximum rotational speed Through the experimental results, a validity of the simulated one is confirmed.
Abstract: Six parameters, the effective diffusivity (De),
activation energy of De, pre-exponential factor of De, amount
(ASOW) of self-organized water species, and amplitude (α) of the
forced oscillation of the molecular mobility (1/tC) derived from the
forced cyclic temperature change operation, were characterized by
using six typical foods, squid, sardines, scallops, salmon, beef, and
pork, as a function of the correlation time (tC) of the water molecule-s
proton retained in the foods. Each of the six parameters was clearly
divided into the water species A1 and A2 at a specified value of tC
=10-8s (=CtC), indicating an anomalous change in the physicochemical
nature of the water species at the CtC. The forced oscillation of 1/tC
clearly demonstrated a characteristic mode depending on the food
shown as a three dimensional map associated with 1/tC, the amount of
self-organized water, and tC.
Abstract: The 20th century has brought much development to the practice of Architecture worldwide, and technology has bridged inhabitation limits in many regions of the world with high levels of comfort and conveniences, most times at high costs to the environment. Throughout the globe, the tropical countries are being urbanized at an unprecedented rate and housing has become a major issue worldwide, in light of increased demand and lack of appropriate infra-structure and planning. Buildings and urban spaces designed in tropical cities have mainly adopted external concepts that in most cases do not fit the needs of the inhabitants living in such harsh climatic environment, and when they do, do so at high financial, environmental and cultural costs. Traditional architectural practices can provide valuable understanding on how self-reliance and autonomy of construction can be reinforced in rural-urban tropical environments. From traditional housing knowledge, it is possible to derive lessons for the development of new construction materials that are affordable, environmentally friendly, culturally acceptable and accesible to all.Specifically to the urban context, such solutions are of outmost importance, given the needs to a more democratic society, where access to housing is considered high in the agenda for development. Traditional or rural constructions are also ongoing through extensive changes eventhough they have mostly adopted climate-responsive building practices relying on local resources (with minimum embodied energy) and energy (for comfort and quality of life). It is important to note that many of these buildings can actually be called zero-energy, and hold potential answers to enable transition from high energy, high cost, low comfort urban habitations to zero/low energy habitations with high quality urban livelihood. Increasing access to modern urban lifestyels have also an effect on the aspirations from people in terms of performance, comfort and convenience in terms of their housing and the way it is produced and used. These aspirations are resulting in transitions from localresource dependent habitations- to non-local resource based highenergy urban style habitations. And such transitions are resulting in the habitations becoming increasingly unsuited to the local climatic conditions with increasing discomfort, ill-health, and increased CO2 emissions and local environmental disruption. This research studies one specific transition group in the context of 'water communities' in tropical-equatorial regions: Ribeirinhos housing typology (Amazonas, Brazil). The paper presents the results of a qualitative sustainability assessment of the housing typologies under transition, found at the Ribeirinhos communities.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: Leading topic of this article is description of Lorentz
forces in the container with cuboid and cylindrical shape. Inside of
the container is an electrically conductive melt. This melt is driven by
rotating magnetic field. Input data for comparing Lorentz forces in
the container with cuboid shape were obtained from the computing
program NS-FEM3D, which uses DDS method of computing. Values
of Lorentz forces for container with cylindrical shape were obtained
from inferred analytical formula.
Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: Command and Control (C2) system and its interfacethe
Common Operational Picture (COP) are main means that
supports commander in its decision making process. COP contains
information about friendly and enemy unit positions. The friendly
position is gathered via tactical network. In the case of tactical
network failure the information about units are not available. The
tactical simulator can be used as a tool that is capable to predict
movements of units in respect of terrain features. Article deals with
an experiment that was based on Czech C2 system that is in the case
of connectivity lost fed by VR Forces simulator. Article analyzes
maximum time interval in which the position created by simulator is
still usable and truthful for commander in real time.
Abstract: Truss spars are used for oil exploitation in deep and ultra-deep water if storage crude oil is not needed. The linear hydrodynamic analysis of truss spar in random sea wave load is necessary for determining the behaviour of truss spar. This understanding is not only important for design of the mooring lines, but also for optimising the truss spar design. In this paper linear hydrodynamic analysis of truss spar is carried out in frequency domain. The hydrodynamic forces are calculated using the modified Morison equation and diffraction theory. Added mass and drag coefficients of truss section computed by transmission matrix and normal acceleration and velocity component acting on each element and for hull section computed by strip theory. The stiffness properties of the truss spar can be separated into two components; hydrostatic stiffness and mooring line stiffness. Then, platform response amplitudes obtained by solved the equation of motion. This equation is non-linear due to viscous damping term therefore linearised by iteration method [1]. Finally computed RAOs and significant response amplitude and results are compared with experimental data.
Abstract: Three dimensional simulations in tube in tube heat
exchangers are investigated numerically in this study. In these
simulations forced convective heat transfer and laminar flow of
single-phase water are considered. In order to measure heat transfer
parameters in these heat exchangers, FLUENT CFD Solver is used in
this numerical method. For the purpose of creating geometry and
exert boundary and initial conditions in the present model, finite
volume method in Computational Fluid Dynamics is used in this
study. In the present study, at each Z-location, variation of local
temperatures, heat flux and Nusselt number at the whole tube is
investigated in detail. Thereafter, averaged computational Nusselt
number in this model is calculated. In addition, conceivable pressure
drops have been obtained at each Z-location in this model. Then,
pressure drop values in the present model are explored. Finally, all
the numerical results for this kind of heat exchanger will be discussed
precisely.
Abstract: Cutting fluids, usually in the form of a liquid, are
applied to the chip formation zone in order to improve the cutting
conditions. Cutting fluid can be expensive and represents a biological
and environmental hazard that requires proper recycling and
disposal, thus adding to the cost of the machining operation. For
these reasons dry cutting or dry machining has become an
increasingly important approach; in dry machining no coolant or
lubricant is used. This paper discussed the effect of the dry cutting on
cutting force and tool life when machining aerospace materials
(Haynes 242) with using two different coated carbide cutting tools
(TiAlN and TiN/MT-TiCN/TiN). Response surface method (RSM)
was used to minimize the number of experiments. ParTiAlN Swarm
Optimisation (PSO) models were developed to optimize the
machining parameters (cutting speed, federate and axial depth) and
obtain the optimum cutting force and tool life. It observed that
carbide cutting tool coated with TiAlN performed better in dry
cutting compared with TiN/MT-TiCN/TiN. On other hand, TiAlN
performed more superior with using of 100 % water soluble coolant.
Due to the high temperature produced by aerospace materials, the
cutting tool still required lubricant to sustain the heat transfer from
the workpiece.
Abstract: RoboCup Rescue simulation as a large-scale Multi
agent system (MAS) is one of the challenging environments for
keeping coordination between agents to achieve the objectives
despite sensing and communication limitations. The dynamicity of
the environment and intensive dependency between actions of
different kinds of agents make the problem more complex. This point
encouraged us to use learning-based methods to adapt our decision
making to different situations. Our approach is utilizing
reinforcement leaning. Using learning in rescue simulation is one of
the current ways which has been the subject of several researches in
recent years. In this paper we present an innovative learning method
implemented for Police Force (PF) Agent. This method can cope
with the main difficulties that exist in other learning approaches.
Different methods used in the literature have been examined. Their
drawbacks and possible improvements have led us to the method
proposed in this paper which is fast and accurate. The Brain
Emotional Learning Based Intelligent Controller (BELBIC) is our
solution for learning in this environment. BELBIC is a
physiologically motivated approach based on a computational model
of amygdale and limbic system. The paper presents the results
obtained by the proposed approach, showing the power of BELBIC
as a decision making tool in complex and dynamic situation.
Abstract: The paper deals with the analysis of the dynamic
response of footbridges under human - induced dynamic loads.
This is a frequently occurring and often dominant load for
footbridges as it stems from the very purpose of a footbridge - to
convey pedestrian. Due to the emergence of new materials and
advanced engineering technology, slender footbridges are
increasingly becoming popular to satisfy the modern transportation
needs and the aesthetical requirements of the society. These
structures however are always lively with low stiffness, low mass,
low damping and low natural frequencies. As a consequence, they are
prone to vibration induced by human activities and can suffer severe
vibration serviceability problems, particularly in the lateral direction.
Pedestrian bridges are designed according to first and second limit
states, these are the criteria involved in response to static design load.
However, it is necessary to assess the dynamic response of bridge
design load on pedestrians and assess it impact on the comfort of the
user movement. Usually the load is considered a person or a small
group which can be assumed in perfect motion synchronization.
Already one person or small group can excite significant vibration of
the deck. In order to calculate the dynamic response to the movement
of people, designer needs available and suitable computational model
and criteria. For the calculation program ANSYS based on finite
element method was used.
Abstract: Numerical investigation of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann methods at different Reynolds numbers. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations, streamlines and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The Reynolds numbers affected the physical quantities.
Abstract: Processing the data by computers and performing
reasoning tasks is an important aim in Computer Science. Semantic
Web is one step towards it. The use of ontologies to enhance the
information by semantically is the current trend. Huge amount of
domain specific, unstructured on-line data needs to be expressed in
machine understandable and semantically searchable format.
Currently users are often forced to search manually in the results
returned by the keyword-based search services. They also want to use
their native languages to express what they search. In this paper, an
ontology-based automated question answering system on software
test documents domain is presented. The system allows users to enter
a question about the domain by means of natural language and
returns exact answer of the questions. Conversion of the natural
language question into the ontology based query is the challenging
part of the system. To be able to achieve this, a new algorithm
regarding free text to ontology based search engine query conversion
is proposed. The algorithm is based on investigation of suitable
question type and parsing the words of the question sentence.
Abstract: The thermal expansion behaviour of silicon carbide
(SCS-2) fibre reinforced 6061 aluminium matrix composite subjected
to the influenced thermal mechanical cycling (TMC) process were
investigated. The thermal stress has important effect on the
longitudinal thermal expansion coefficient of the composites. The
present paper used experimental data of the thermal expansion
behaviour of a SiC/Al composite for temperatures up to 370°C, in
which their data was used for carrying out modelling of theoretical
predictions.
Abstract: The accelerated growth in aircraft industries desire
effectual schemes, programs, innovative designs of advanced systems
and facilities to accomplish the augmenting need for home-free air
transportation. In this paper, a contemporary conceptual design of a
cambered airfoil has been proposed in order to providing augmented
effective lift force relative to the airplane, and to eliminating
drawbacks and limitations of an airfoil in a commercial airplane by
using a kind of smart materials. This invention of an unsymmetrical
airfoil structure utilizes the amplified air momentum around the
airfoil and increased camber length to providing improved aircraft
performance and assist to enhancing the reliability of the aircraft
components. Moreover, this conjectured design helps to reducing
airplane weight and total drag.
Abstract: The objective of the present paper is a numerical
analysis of the flow forces acting on spool surfaces of a pressure
regulated valve. The transient, compressible and turbulent flow
structures inside the valve are simulated using ANSYS FLUENT
coupled with a special UDF. Here, valve inlet pressure is varied in a
stepwise manner. For every value of inlet pressure, transient analysis
leads to a quasi-static flow through the valve. Spool forces are
calculated based on different pressures at inlet. From this information
of spool forces, pressure characteristic of the passive control circuit
has been derived.