Abstract: A study concerning the photocatalytic decolourization
of Congo red (CR) dye, over artificial UV irradiation is presented.
Photocatalysts based on a commercial titanium dioxide (TiO2)
modified with transition metals (Ni, Cu and Zn) were used. The
dopage method used was wet impregnation. A TiO2 sample without
salt was subjected to the same hydrothermal treatment to be used as
reference. Congo red solutions to several pH conditions (natural and
basic) were used to evaluate photocatalytic performance of each
doped catalysts. Photodecolourization percentage was measured
spectrofotrometically after 3 h of treatment to 499 nm as response
variable. Kinetics investigations of photodegradation indicated that
reactions obey to Langmuir-Hinshelwood model and pseudo–first
order law. The rate constant studies of photocatalytic decolourization
reactions for Zn–TiO2 and Cu–TiO2 photocatalysts indicated that in
all cases the rate constant of the reaction was higher than that of TiO2
undoped. These results show that nature of the metal modifying the
TiO2 influence on the efficiency of the photocatalyst evaluated in
process. Ni does not present an additional effect compared with TiO2,
while Zn enhances the photoactivity due to its electronic properties.
Abstract: Object-oriented simulation is considered one of the most sophisticated techniques that has been widely used in planning, designing, executing and maintaining construction projects. This technique enables the modeler to focus on objects which is extremely important for thorough understanding of a system. Thus, identifying an object is an essential point of building a successful simulation model. In a maintenance process an object is a maintenance work order (MWO). This study demonstrates a maintenance simulation model for the building maintenance division of Saudi Consolidated Electric Company (SCECO) in Dammam, Saudi Arabia. The model focused on both types of maintenance processes namely: (1) preventive maintenance (PM) and (2) corrective maintenance (CM). It is apparent from the findings that object-oriented simulation is a good diagnostic and experimental tool. This is because problems, limitations, bottlenecks and so forth are easily identified. These features are very difficult to obtain when using other tools.
Abstract: In this study, cometabolic biodegradation of
chloroform was experimented with mixed cultures in the presence of
various organic solvents like methanol, ethanol, isopropanol, acetone,
acetonitrile and toluene as these are predominant discharges in
pharmaceutical industries. Toluene and acetone showed higher
specific chloroform degradation rate when compared to other
compounds. Cometabolic degradation of chloroform was further
confirmed by observation of free chloride ions in the medium. An
extended Haldane model, incorporating the inhibition due to
chloroform and the competitive inhibition between primary
substrates, was developed to predict the biodegradation of primary
substrates, cometabolic degradation of chloroform and the biomass
growth. The proposed model is based on the use of biokinetic
parameters obtained from single substrate degradation studies. The
model was able to satisfactorily predict the experimental results of
ternary and quaternary mixtures. The proposed model can be used for
predicting the performance of bioreactors treating discharges from
pharmaceutical industries.
Abstract: A spatial analysis of a large 20th century urban settlement (town/city) easily presents the celebrated central Business District (CBD). Theories of Urban Land Economics have easily justified and attempted to explain the existence of such a district activity area within the cityscape. This work examines the gradual emergence and development of the CBD in Lafia Town, Nigeria over 20 years and the attended urban problems caused by its emergence. Personal knowledge and observation of land use change are the main sources of data for the work, with unstructured interview with residents. The result are that the absence of a co-ordinate land use plan for the town, multi-nuclei nature, and regional location of surrounding towns have affected the growth pattern, hence the CBD. Traffic congestion, dispersed CBD land uses are some of the urban planning problems. The work concludes by advocating for integrating CBD uses.
Abstract: The work presented in this study is related to an
energy system analysis based on passive cooling system for
dwellings. It consists to solar chimney energy performances
determination versus geometrical and environmental considerations
as the size and inlet width conditions of the chimney. Adrar site
located in the southern region of Algeria is chosen for this study
according to ambient temperature and solar irradiance technical data
availability. Obtained results are related to the glazing temperature
distributions, the chimney air flow and internal wall temperatures.
The air room change per hour (ACH) parameter, the outlet air
velocity and mass air flow rate are also determined. It is shown that
the chimney width has a significant effect on energy performances
compared to its entry size. A good agreement is observed between
these results and those obtained by others from the literature.
Abstract: The enzyme alkaline protease production was determined under
solid state fermentation using the soil bacteria Serratia marcescens
sp7. The maximum production was obtained from wheat bran
medium than ground nut shell and chemically defined medium. The
physiological fermentation factors such as pH of the medium (pH 8),
Temperature (40oC) and incubation time (48 hrs) played a vital role
in alkaline protease production in all the above. 100Mm NaCl has
given better resolution during elution of the enzymes. The enzyme
production was found to be associated with growth of the bacterial
culture.
Abstract: We developed a new method based on quasimolecular
modeling to simulate the cavity flow in three cavity
shapes: rectangular, half-circular and bucket beer in cgs units. Each
quasi-molecule was a group of particles that interacted in a fashion
entirely analogous to classical Newtonian molecular interactions.
When a cavity flow was simulated, the instantaneous velocity vector
fields were obtained by using an inverse distance weighted
interpolation method. In all three cavity shapes, fluid motion was
rotated counter-clockwise. The velocity vector fields of the three
cavity shapes showed a primary vortex located near the upstream
corners at time t ~ 0.500 s, t ~ 0.450 s and t ~ 0.350 s, respectively.
The configurational kinetic energy of the cavities increased as time
increased until the kinetic energy reached a maximum at time t ~
0.02 s and, then, the kinetic energy decreased as time increased. The
rectangular cavity system showed the lowest kinetic energy, while
the half-circular cavity system showed the highest kinetic energy.
The kinetic energy of rectangular, beer bucket and half-circular
cavities fluctuated about stable average values 35.62 x 103, 38.04 x
103 and 40.80 x 103 ergs/particle, respectively. This indicated that the
half-circular shapes were the most suitable shape for a shrimp pond
because the water in shrimp pond flows best when we compared with
rectangular and beer bucket shape.
Abstract: Due to the fact that in the new century customers tend
to express globally increasing demands, networks of interconnected
businesses have been established in societies and the management of
such networks seems to be a major key through gaining competitive
advantages. Supply chain management encompasses such managerial
activities. Within a supply chain, a critical role is played by quality.
QFD is a widely-utilized tool which serves the purpose of not only
bringing quality to the ultimate provision of products or service
packages required by the end customer or the retailer, but it can also
initiate us into a satisfactory relationship with our initial customer;
that is the wholesaler. However, the wholesalers- cooperation is
considerably based on the capabilities that are heavily dependent on
their locations and existing circumstances. Therefore, it is undeniable
that for all companies each wholesaler possesses a specific
importance ratio which can heavily influence the figures calculated in
the House of Quality in QFD. Moreover, due to the competitiveness
of the marketplace today, it-s been widely recognized that
consumers- expression of demands has been highly volatile in
periods of production. Apparently, such instability and proneness to
change has been very tangibly noticed and taking it into account
during the analysis of HOQ is widely influential and doubtlessly
required. For a more reliable outcome in such matters, this article
demonstrates the application viability of Analytic Network Process
for considering the wholesalers- reputation and simultaneously
introduces a mortality coefficient for the reliability and stability of
the consumers- expressed demands in course of time. Following to
this, the paper provides further elaboration on the relevant
contributory factors and approaches through the calculation of such
coefficients. In the end, the article concludes that an empirical
application is needed to achieve broader validity.
Abstract: The focal spot of a high intensity focused ultrasound
transducer is small. To heat a large target volume, multiple treatment spots are required. If the power of each treatment spot is fixed, it could
results in insufficient heating of initial spots and over-heating of later ones, which is caused by the thermal diffusion. Hence, to produce a
uniform heated volume, the delivered energy of each treatment spot
should be properly adjusted. In this study, we proposed an iterative, extrapolation technique to adjust the required ultrasound energy of
each treatment spot. Three different scanning pathways were used to evaluate the performance of this technique. Results indicate that by using the proposed technique, uniform heating volume could be obtained.
Abstract: Computer technology and the Internet have made a
breakthrough in the existence of data communication. This has
opened a whole new way of implementing steganography to ensure
secure data transfer. Steganography is the fine art of hiding the
information. Hiding the message in the carrier file enables the
deniability of the existence of any message at all. This paper designs
a stego machine to develop a steganographic application to hide data
containing text in a computer video file and to retrieve the hidden
information. This can be designed by embedding text file in a video
file in such away that the video does not loose its functionality using
Least Significant Bit (LSB) modification method. This method
applies imperceptible modifications. This proposed method strives
for high security to an eavesdropper-s inability to detect hidden
information.
Abstract: For micro-gyroscopes, the angular rate detection components have to oscillate forwards and backwards alternatively. An innovative design of micro-electromagnetic drive module is proposed to make a Π-type disc reciprocally and efficiently rotate within a certain of angular interval. Twelve Electromagnetic poles enclosing the thin disc are designed to provide the magnetic drive power. Isotropic etching technique is employed to fabricate the high-aspect-ratio trench, so that the contact angle of wire against trench can be increased and the potential defect of cavities and pores within the wire can be prevented. On the other hand, a Π-type thin disc is designed to conduct the pitch motion as an angular excitation, in addition to spinning, is exerted on the gyroscope. The efficacy of the micro-magnetic drive module is verified by the commercial software, Ansoft Maxewll. In comparison with the conventional planar windings in micro-scale systems, the magnetic drive force is increased by 150%.
Abstract: The paper describes the carbonate microfacies identified in the Sinjar Formation (Late Paleocene–Early Eocene) cropping out in Qara Dagh Mountain, near Sulekan Village approximately 20km south–west of Sulaimani (Iraq). One section (62m thick) has been measured in the field and closely sampled to undertake detailed microfaciesal and micropalaeontological studies to determine the formation-s age and environment of deposition. A samples were collected illustrating all the lithological changes along the section. The limestone in the studied area is hard and extremely rich in large foraminifers (soritids, rotaliids, nummulites, miliolids) and green algae (dasycladales). The investigation of the thin sections allowed us to identify the carbonate microfacies (18 types and subtypes) and the micropaleontological association (foraminifers and green algae), to determine the age of formation and to reconstruct the paleoenvironment of deposition (fore-reef, reef, back-reef). Based on the field observations and the studied thin sections, we determined three Units of a carbonate platform (I, II and III) from the base to the top of the section: Unit I with coralgal associations, Unit II is dominated by larger foraminifers and haracterized by the absence of coralgal associations, while Unit III is dominated by small foraminifers (mostly miliolids), peloids and green algae. It is partially dolomitized.
Abstract: Sustainable development is a concept which was
originated in Burtland commission in 1978. Although this concept
was born with environmental aspects, it is penetrated in all areas
rapidly, turning into a dominate view of planning. Concentrating on
future generation issue, especially when talking about heritage has a
long story. Each approach with all of its characteristics illustrates
differences in planning, hence planning always reflects the dominate
idea of its age. This paper studies sustainable development in
planning for historical cities with the aim of finding ways to deal
with heritage in planning for historical cities in Iran. Through this, it
will be illustrated how challenges between sustainable concept and
heritage could be concluded in planning.
Consequently, the paper will emphasize on:
Sustainable development in city planning
Trends regarding heritage
Challenges due to planning for historical cities in Iran
For the first two issues, documentary method regarding the
sustainable development and heritage literature is considered. As the
next step focusing on Iranian historical cities require considering the
urban planning and management structure and identifying the main
challenges related to heritage, so analyzing challenges regarding
heritage is considered. As the result it would be illustrated that key
issue in such planning is active conservation to improve and use the
potential of heritage while it's continues conservation is guaranteed.
By emphasizing on the planning system in Iran it will be obvious that
some reforms are needed in this system and its way of relating with
heritage. The main weakness in planning for historical cities in Iran
is the lack of independent city management. Without this factor
achieving active conservation as the main factor of sustainable
development would not be possible.
Abstract: Traditional development of wireless sensor network
mote is generally based on SoC1 platform. Such method of
development faces three main drawbacks: lack of flexibility in terms
of development due to low resource and rigid architecture of SoC;
low capability of evolution and portability versus performance if
specific micro-controller architecture features are used; and the rapid
obsolescence of micro-controller comparing to the long lifetime of
power plants or any industrial installations. To overcome these
drawbacks, we have explored a new approach of development of
wireless sensor network mote using a hybrid FPGA technology. The
application of such approach is illustrated through the
implementation of an innovative wireless sensor network protocol
called OCARI.
Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: Research papers are usually evaluated via peer
review. However, peer review has limitations in evaluating research
papers. In this paper, Scienstein and the new idea of 'collaborative
document evaluation' are presented. Scienstein is a project to
evaluate scientific papers collaboratively based on ratings, links,
annotations and classifications by the scientific community using the
internet. In this paper, critical success factors of collaborative
document evaluation are analyzed. That is the scientists- motivation
to participate as reviewers, the reviewers- competence and the
reviewers- trustworthiness. It is shown that if these factors are
ensured, collaborative document evaluation may prove to be a more
objective, faster and less resource intensive approach to scientific
document evaluation in comparison to the classical peer review
process. It is shown that additional advantages exist as collaborative
document evaluation supports interdisciplinary work, allows
continuous post-publishing quality assessments and enables the
implementation of academic recommendation engines. In the long
term, it seems possible that collaborative document evaluation will
successively substitute peer review and decrease the need for
journals.
Abstract: This paper describes the results of an extensive study
and comparison of popular hash functions SHA-1, SHA-256,
RIPEMD-160 and RIPEMD-320 with JERIM-320, a 320-bit hash
function. The compression functions of hash functions like SHA-1
and SHA-256 are designed using serial successive iteration whereas
those like RIPEMD-160 and RIPEMD-320 are designed using two
parallel lines of message processing. JERIM-320 uses four parallel
lines of message processing resulting in higher level of security than
other hash functions at comparable speed and memory requirement.
The performance evaluation of these methods has been done by using
practical implementation and also by using step computation
methods. JERIM-320 proves to be secure and ensures the integrity of
messages at a higher degree. The focus of this work is to establish
JERIM-320 as an alternative of the present day hash functions for the
fast growing internet applications.
Abstract: The present study focuses on methods allowing a convenient and quick calculation of the SIFs in order to predict the static adhesive strength of bonded joints. A new SIF calculation method is proposed, based on the stresses obtained from a FE model at a reference point located in the adhesive layer at equal distance of the free-edge and of the two interfaces. It is shown that, even limiting ourselves to the two main modes, i.e. the opening and the shearing modes, and using the values of the stresses resulting from a low detailed FE model, an efficient calculation of the peeling stress at adhesive-substrate corners can be obtained by this way. The proposed method is interesting in that it can be the basis of a prediction tool that will allow the designer to quickly evaluate the SIFs characterizing a particular application without developing a detailed analysis.
Abstract: A known iterative computational procedure is used for
internal normal ball loads calculation in statically loaded single-row,
angular-contact ball bearings, subjected to a known thrust load,
which is applied in the inner ring at the geometric bearing center line.
Numerical aspects of the iterative procedure are discussed.
Numerical examples results for a 218 angular-contact ball bearing
have been compared with those from the literature. Twenty figures
are presented showing the geometrical features, the behavior of the
convergence variables and the following parameters as functions of
the thrust load: normal ball loads, contact angle, distance between
curvature centers, and normal ball and axial deflections between the
raceways.
Abstract: Autofluorescence (AF) bronchoscopy is an
established method to detect dysplasia and carcinoma in situ (CIS).
For this reason the “Sotiria" Hospital uses the Karl Storz D-light
system. However, in early tumor stages the visualization is not that
obvious. With the help of a PC, we analyzed the color images we
captured by developing certain tools in Matlab®. We used statistical
methods based on texture analysis, signal processing methods based
on Gabor models and conversion algorithms between devicedependent
color spaces. Our belief is that we reduced the error made
by the naked eye. The tools we implemented improve the quality of
patients' life.