Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: This research was conducted in the Mae Sot
Watershed where located in the Moei River Basin at the Upper
Salween River Basin in Tak Province, Thailand. The Mae Sot
Municipality is the largest urban area in Tak Province and situated in
the midstream of the Mae Sot Watershed. It usually faces flash flood
problem after heavy rain due to poor flood management has been
reported since economic rapidly bloom up in recent years. Its
catchment can be classified as ungauged basin with lack of rainfall
data and no any stream gaging station was reported. It was attached
by most severely flood events in 2013 as the worst studied case for
all those communities in this municipality. Moreover, other problems
are also faced in this watershed, such shortage water supply for
domestic consumption and agriculture utilizations including a
deterioration of water quality and landslide as well. The research
aimed to increase capability building and strengthening the
participation of those local community leaders and related agencies to
conduct better water management in urban area was started by mean
of the data collection and illustration of the appropriated application
of some short period rainfall forecasting model as they aim for better
flood relief plan and management through the hydrologic model
system and river analysis system programs. The authors intended to
apply the global rainfall data via the integrated data viewer (IDV)
program from the Unidata with the aim for rainfall forecasting in a
short period of 7-10 days in advance during rainy season instead of
real time record. The IDV product can be present in an advance
period of rainfall with time step of 3-6 hours was introduced to the
communities. The result can be used as input data to the hydrologic
modeling system model (HEC-HMS) for synthesizing flood
hydrographs and use for flood forecasting as well. The authors
applied the river analysis system model (HEC-RAS) to present flood
flow behaviors in the reach of the Mae Sot stream via the downtown
of the Mae Sot City as flood extents as the water surface level at
every cross-sectional profiles of the stream. Both models of HMS and
RAS were tested in 2013 with observed rainfall and inflow-outflow
data from the Mae Sot Dam. The result of HMS showed fit to the
observed data at the dam and applied at upstream boundary discharge
to RAS in order to simulate flood extents and tested in the field, and
the result found satisfying. The product of rainfall from IDV was fair
while compared with observed data. However, it is an appropriate
tool to use in the ungauged catchment to use with flood hydrograph
and river analysis models for future efficient flood relief plan and
management.
Abstract: In recent years, the hair building fiber has become
popular, in other words, it is an effective method which helps people
who suffer hair loss or sparse hair since the hair building fiber is
capable to create a natural look of simulated hair rapidly. In the
markets, there are a lot of hair fiber brands that have been designed to
formulate an intense bond with hair strands and make the hair appear
more voluminous instantly. However, those products have their own
set of properties. Thus, in this report, some measurement techniques
are proposed to identify those products. Up to five different brands of
hair fiber are tested. The electrostatic and dielectric properties of the
hair fibers are macroscopically tested using design DC and high
frequency microwave techniques. Besides, the hair fibers are
microscopically analysis by magnifying the structures of the fiber
using scanning electron microscope (SEM). From the SEM photos,
the comparison of the uniformly shaped and broken rate of the hair
fibers in the different bulk samples can be observed respectively.
Abstract: This paper presents a methodology using
Gravitational Search Algorithm for optimal placement of Phasor
Measurement Units (PMUs) in order to achieve complete
observability of the power system. The objective of proposed
algorithm is to minimize the total number of PMUs at the power
system buses, which in turn minimize installation cost of the PMUs.
In this algorithm, the searcher agents are collection of masses which
interact with each other using Newton’s laws of gravity and motion.
This new Gravitational Search Algorithm based method has been
applied to the IEEE 14-bus, IEEE 30-bus and IEEE 118-bus test
systems. Case studies reveal optimal number of PMUs with better
observability by proposed method.
Abstract: The research on “The Way of Life of the Civil Servant
Community under the Bureau of the Royal Household” aims to study
1) the way of life of the people who live in the civil servant
community in Tha Wasukri, and 2) the model of community
administration of civil servants under the Bureau of the Royal
Household. This research is conducted qualitatively and
quantitatively by collecting data from interviews, focus group
discussion, participant and non-participant observation along with the
data from questionnaire based on age groups which include elder
group, working age group and youth group.
The result of the research shows that the origin of this community
is related to the history during the Rama V’s reign. It has been a
harbor for the king to boat in any royal ceremonies; this custom is
still maintained until today. The status or position of person who
serves the king in terms of working is often inherited from the bureau
of the Royal Household based on his/her consanguinity and, hence,
further receives the rights to live in the Tha Wasukri area. Therefore,
this community has some special characteristics demonstrating the
way of living influenced by the regulation of the Bureau of the Royal
Household such as respecting elders and interdependence in which
there is internal social organization with the practice of bureaucracy
in going in and out the community. The person who has rights to live
here must be friendly to everybody so that this community will be a
safe place for lives and property. The administration based on the
model of Bangkok for local administration was used as an external
structure only, but the way of living still follows the practice of the
Bureau of the Royal Household.
Abstract: Since, it is essential to provide homeless people by the
earthquake with safe, habitable accommodation repairing medium
and slight levels of damage at the connection parts should be
undertaken. In order to prove that a repaired connection was
sufficiently strong, a precast beam to column post tensioned
connection was tested in three phases. In phase one, the middle level
damage was observed at 6% drift at these connections. As a result of
the extra loads applied, little damage was observed. In the last phase,
the four connections tested in the first phase were repaired using
epoxy resin and then retested. The results from the tests on the
repaired precast and the undamaged specimens showed that the
repaired specimens were sufficiently strong, thus proving that repair
to damaged precast beam to column post tensioned connections can
be undertaken.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: A numerical study of natural convection heat transfer
in water filled cavity has been examined in 3-Dfor single phase liquid
cooling system by using an array of parallel plate fins mounted to one
wall of a cavity. The heat generated by a heat source represents a
computer CPU with dimensions of 37.5∗37.5mm mounted on
substrate. A cold plate is used as a heat sink installed on the opposite
vertical end of the enclosure. The air flow inside the computer case is
created by an exhaust fan. A turbulent air flow is assumed and k-ε
model is applied. The fins are installed on the substrate to enhance
the heat transfer. The applied power energy range used is between 15
- 40W. In order to determine the thermal behaviour of the cooling
system, the effect of the heat input and the number of the parallel
plate fins are investigated. The results illustrate that as the fin number
increases the maximum heat source temperature decreases. However,
when the fin number increases to critical value the temperature start
to increase due to the fins are too closely spaced and that cause the
obstruction of water flow. The introduction of parallel plate fins
reduces the maximum heat source temperature by 10% compared to
the case without fins. The cooling system maintains the maximum
chip temperature at 64.68°C when the heat input was at 40W that is
much lower than the recommended computer chips limit temperature
of no more than 85°C and hence the performance of the CPU is
enhanced.
Abstract: The present article seeks to carry out along the lines of
interpretation of the recent Portuguese Constitutional Court case law
on the possibility of an employee to observe a worship day imposed
by religious beliefs. In this approach to the question, considerations
on the subject of the relationship between religious freedom and
labour relations will inevitably arise. We intend to draw conclusions
of practical application from the court decisions on the matter of
freedom of religion.
Abstract: The air transport impact on environment is more than
ever a limitative obstacle to the aeronautical industry continuous
growth. Over the last decades, considerable effort has been carried
out in order to obtain quieter aircraft solutions, whether by changing
the original design or investigating more silent maneuvers. The
noise propagated by rotating surfaces is one of the most important
sources of annoyance, being present in most aerial vehicles. Bearing
this is mind, CEIIA developed a new computational chain for
noise prediction with in-house software tools to obtain solutions in
relatively short time without using excessive computer resources. This
work is based on the new acoustic tool, which aims to predict the
rotor noise generated during steady and maneuvering flight, making
use of the flexibility of the C language and the advantages of GPU
programming in terms of velocity. The acoustic tool is based in the
Formulation 1A of Farassat, capable of predicting two important
types of noise: the loading and thickness noise. The present work
describes the most important features of the acoustic tool, presenting
its most relevant results and framework analyses for helicopters and
UAV quadrotors.
Abstract: This paper examines how “Zakat” provides fair
income redistribution and aids the struggle against poverty. Providing
fair income redistribution and combating poverty constitutes some of
the fundamental tasks performed by countries all over the world.
Each country seeks a solution for these problems according to their
political, economic and administrative styles through applying
various economic and financial policies. The same situation can be
handled via “zakat” association in Islam. Nowadays, we observe
different versions of “zakat” in developed countries. Applications
such as negative income tax denote merely a different form of
“zakat” that is being applied almost in the same way but under
changed names. However, the minimum values to donate under zakat
(e.g. 85 gr. gold and 40 animals) get altered and various amounts are
put into practice. It might be named as negative income tax instead of
zakat, nonetheless, these applications are based on the Holy Koran
and the hadith released 1400 years ago. Besides, considering the
savage and slavery in the world at those times, we might easily
recognize the true value of the zakat being applied for the first time
then in the Islamic system. Through zakat, governments are able to
transfer incomes to the poor as a means of enabling them achieve the
minimum standard of living required. With regards to who benefits
from the Zakat, an objective and fair criteria was used to determine
who benefits from the zakat contrary to the notion that it was based
on peoples’ own choices. Since the zakat is obligatory, the transfers
do not get forwarded directly but via the government and get
distributed, which requires vast governmental organizations. Through
the application of Zakat, reduced levels of poverty can be achieved
and also ensure the fair income redistribution.
Abstract: Biofuels production has come forth as a future
technology to combat the problem of depleting fossil fuels. Bio-based
ethanol production from enzymatic lignocellulosic biomass
degradation serves an efficient method and catching the eye of
scientific community. High cost of the enzyme is the major obstacle
in preventing the commercialization of this process. Thus main
objective of the present study was to optimize composition of
medium components for enhancing cellulase production by newly
isolated strain of Bacillus tequilensis. Nineteen factors were taken
into account using statistical Plackett-Burman Design. The significant
variables influencing the cellulose production were further employed
in statistical Response Surface Methodology using Central
Composite Design for maximizing cellulase production. The
optimum medium composition for cellulase production was: peptone
(4.94 g/L), ammonium chloride (4.99 g/L), yeast extract (2.00 g/L),
Tween-20 (0.53 g/L), calcium chloride (0.20 g/L) and cobalt chloride
(0.60 g/L) with pH 7, agitation speed 150 rpm and 72 h incubation at
37oC. Analysis of variance (ANOVA) revealed high coefficient of
determination (R2) of 0.99. Maximum cellulase productivity of 11.5
IU/ml was observed against the model predicted value of 13 IU/ml.
This was found to be optimally active at 60oC and pH 5.5.
Abstract: Although, arsenic trioxide has been the subject of
toxicological research, in vitro cytotoxicity and genotoxicity studies
using relevant cell models and uniform methodology are not well
elucidated. Hence, the aim of the present study was to evaluate the
cytotoxicity and genotoxicity induced by arsenic trioxide in human
keratinocytes (HaCaT) using the MTT [3-(4, 5-dimethylthiazol-2-yl)-
2,5-diphenyltetrazolium bromide] and alkaline single cell gel
electrophoresis (Comet) assays, respectively. Human keratinocytes
were treated with different doses of arsenic trioxide for 4 h prior to
cytogenetic assessment. Data obtained from the MTT assay indicated
that arsenic trioxide significantly reduced the viability of HaCaT cells
in a dose-dependent manner, showing an IC50 value of 34.18 ± 0.6
μM. Data generated from the comet assay also indicated a significant
dose-dependent increase in DNA damage in HaCaT cells associated
with arsenic trioxide exposure. We observed a significant increase in
comet tail length and tail moment, showing an evidence of arsenic
trioxide -induced genotoxic damage in HaCaT cells. This study
confirms that the comet assay is a sensitive and effective method to
detect DNA damage caused by arsenic.
Abstract: An investigation into Cahn-Hilliard equation was
carried out through numerical simulation to identify a possible phase
separation for one and two dimensional domains. It was observed that
this equation can reproduce important mass fluxes necessary for
phase separation within the miscibility gap and for coalescence of
particles.
Abstract: This paper presents small signal stability study carried
over the 140-Bus, 31-Machine, 5-Area MEPE system and validated
on free and open source software: PSAT. Well-established linearalgebra
analysis, eigenvalue analysis, is employed to determine the
small signal dynamic behavior of test system. The aspects of local
and interarea oscillations which may affect the operation and
behavior of power system are analyzed. Eigenvalue analysis is carried
out to investigate the small signal behavior of test system and the
participation factors have been determined to identify the
participation of the states in the variation of different mode shapes.
Also, the variations in oscillatory modes are presented to observe the
damping performance of the test system.
Abstract: An experiment was conducted to determine the effect
of pollination on seed quality of rapeseed in Chitwan, Nepal during
2012-2013. The experiment was designed in Randomized Complete
Block with four replications and five treatments. The rapeseed plots
were caged with mosquito nets at 10% flowering except natural
pollination. Two-framed colonies of Apis mellifera L. and Apis
cerana F. were introduced separately for pollination, and control plot
caged without pollinators. The highest germination percent was
observed on Apis cerana F. pollinated plot seeds (90.50%
germination) followed by Apis mellifera L. pollinated plots (87.25 %)
and lowest on control plots (42.00% germination) seeds. Similarly,
seed test weight of Apis cerana F. pollinated plots (3.22 gm/ 1000
seed) and Apis mellifera L. pollinated plots (2.93 gm/1000 seed) were
and lowest on control plots (2.26 gm/ 1000 seed) recorded. Likewise,
oil content was recorded highest on pollinated by Apis cerana F.
(36.1%) followed by pollinated by Apis mellifera L. (35.4%) and
lowest on control plots (32.8%). This study clearly indicated
pollination increases the seed quality of rapeseed and therefore,
management of honeybee is necessary for producing higher quality of
rapeseed under Chitwan condition.
Abstract: The temperature dependence of wettability (wetting
angle, Θ (T)) for Ag-based melts on graphite and Al2O3 substrates is
compared. Typical alloying effects are found, as the Ag host metal is
gradually replaced by various metallic elements. The essence of
alloying lies in the change of the electron/atom (e/a) ratio. This ratio
is also manifested in the shift of wetting angles on the same substrate.
Nevertheless, the effects are partially smeared by other
(metallurgical) factors, like the interaction between the oxygenalloying
elements and by the graphite substrate-oxygen interaction. In
contrast, such effects are not pronounced in the case of Al2O3
substrates. As a consequence, Θ(T) exhibits an opposite trend in the
case of two substrates. Crossovers of the Θ(T) curves were often
found. The positions of crossovers depend on the chemical character
and concentration of solute atoms. Segregation and epitaxial texture
formation after solidification were also observed in certain alloy
drops, especially in high concentration range. This phenomenon is
not yet explained in every detail.
Abstract: This study carried out comparative seismic
performance of reinforced concrete frames infilled by masonry walls
with different heights. Partial and fully infilled reinforced concrete
frames were modeled for the research objectives and the analysis
model for a bare reinforced concrete frame was also established for
comparison. Non–linear static analyses for the studied frames were
performed to investigate their structural behavior under extreme
seismic loads and to find out their collapse mechanism. It was
observed from analysis results that the strengths of the partial infilled
reinforced concrete frames are increased and their ductilities are
reduced, as infilled masonry walls are higher. Especially, reinforced
concrete frames with higher partial infilled masonry walls would
experience shear failures. Non–linear dynamic analyses using 10
earthquake records show that the bare and fully infilled reinforced
concrete frame present stable collapse mechanism while the reinforced
concrete frames with partially infilled masonry walls collapse in more
brittle manner due to short-column effects.
Abstract: Logistics processes of perishable food in the supply
chain include the distribution activities and the real time temperature
monitoring to fulfil the cold chain requirements. The paper presents
the use of RFID (Radio Frequency Identification) technology as an
identification tool of receiving and shipping activities in the cold
store. At the same time, the use of RFID data loggers with
temperature sensors is presented to observe and store the
temperatures for the purpose of analyzing the processes and having
the history data available for traceability purposes and efficient recall
management.