Abstract: It is essential to have a uniform and calm flow field
for a settling tank to have high performance. In general, the
recirculation zones always occurred in sedimentation tanks. The
presence of these regions may have different effects. The nonuniformity
of the velocity field, the short-circuiting at the surface and
the motion of the jet at the bed of the tank that occurs because of the
recirculation in the sedimentation layer, are affected by the geometry
of the tank. There are some ways to decrease the size of these dead
zones, which would increase the performance. One of the ways is to
use a suitable baffle configuration. In this study, the presence of
baffle with different position has been investigated by a finite volume
method, with VOF (Volume of Fluid) model. Besides, the k-ε
turbulence model is used in the numerical calculations. The results
indicate that the best position of the baffle is obtained when the
volume of the recirculation region is minimized or is divided to
smaller part and the flow field trend to be uniform in the settling
zone.
Abstract: While financial institutions have faced difficulties
over the years for a multitude of reasons, the major cause of serious
banking problems continues to be directly related to lax credit
standards for borrowers and counterparties, poor portfolio risk
management, or a lack of attention to changes in economic or other
circumstances that can lead to a deterioration in the credit standing of
a bank's counterparties. Credit risk is most simply defined as the
potential that a bank borrower or counterparty will fail to meet its
obligations in accordance with agreed terms. The goal of credit risk
management is to maximize a bank's risk-adjusted rate of return by
maintaining credit risk exposure within acceptable parameters. Banks
need to manage the credit risk inherent in the entire portfolio as well
as the risk in individual credits or transactions. Banks should also
consider the relationships between credit risk and other risks. The
effective management of credit risk is a critical component of a
comprehensive approach to risk management and essential to the
long-term success of any banking organization. In this research we
also study the relationship between credit risk indices and borrower-s
timely payback in Karafarin bank.
Abstract: This paper adopts a notion of expectation-perception
gap of systems users as information systems (IS) failure. Problems
leading to the expectation-perception gap are identified and modelled
as five interrelated discrepancies or gaps throughout the process of
information systems development (ISD). It describes an empirical
study on how systems developers and users perceive the size of each
gap and the extent to which each problematic issue contributes to the
gap. The key to achieving success in ISD is to keep the expectationperception
gap closed by closing all 5 pertaining gaps. The gap model
suggests that most factors in IS failure are related to organizational,
cognitive and social aspects of information systems design.
Organization requirement analysis, being the weakest link of IS
development, is particularly worthy of investigation.
Abstract: There is lot of work done in prediction of the fault proneness of the software systems. But, it is the severity of the faults that is more important than number of faults existing in the developed system as the major faults matters most for a developer and those major faults needs immediate attention. In this paper, we tried to predict the level of impact of the existing faults in software systems. Neuro-Fuzzy based predictor models is applied NASA-s public domain defect dataset coded in C programming language. As Correlation-based Feature Selection (CFS) evaluates the worth of a subset of attributes by considering the individual predictive ability of each feature along with the degree of redundancy between them. So, CFS is used for the selecting the best metrics that have highly correlated with level of severity of faults. The results are compared with the prediction results of Logistic Models (LMT) that was earlier quoted as the best technique in [17]. The results are recorded in terms of Accuracy, Mean Absolute Error (MAE) and Root Mean Squared Error (RMSE). The results show that Neuro-fuzzy based model provide a relatively better prediction accuracy as compared to other models and hence, can be used for the modeling of the level of impact of faults in function based systems.
Abstract: Among the chemicals used for ammunition production, TNT (Trinitrotoluene) play a significant role since World War I and II. Various types of military weapon utilize TNT in casting process. However, the TNT casting process for warhead is difficult to control the cooling rate of the liquid TNT. This problem occurs because the casting process lacks the equipment to detect the temperature during the casting procedure This study presents the temperature detected by infrared camera to illustrate the cooling rate and cooling zone of curing, and demonstrates the optimization of TNT condition to reduce the risk of air gap occurred in the warhead which can result in the destruction afterward. Premature initiation of explosive-filled projectiles in response to set-back forces during gunfiring cause by casting defects. Finally the study can help improving the process of the TNT casting. The operators can control the curing of TNT inside the case by rising up the heating rod at the proper time. Consequently this can reduce tremendous time of rework if the air gaps occur and increase strength to lower elastic modulus. Therefore, it can be clearly concluded that the use of Infrared Cameras in this process is another method to improve the casting procedure.
Abstract: In this paper we propose a robust environmental sound classification approach, based on spectrograms features driven from log-Gabor filters. This approach includes two methods. In the first methods, the spectrograms are passed through an appropriate log-Gabor filter banks and the outputs are averaged and underwent an optimal feature selection procedure based on a mutual information criteria. The second method uses the same steps but applied only to three patches extracted from each spectrogram.
To investigate the accuracy of the proposed methods, we conduct experiments using a large database containing 10 environmental sound classes. The classification results based on Multiclass Support Vector Machines show that the second method is the most efficient with an average classification accuracy of 89.62 %.
Abstract: The performance of time-reversal MUSIC algorithm will be dramatically degrades in presence of strong noise and multiple scattering (i.e. when scatterers are close to each other). This is due to error in determining the number of scatterers. The present paper provides a new approach to alleviate such a problem using an information theoretic criterion referred as minimum description length (MDL). The merits of the novel approach are confirmed by the numerical examples. The results indicate the time-reversal MUSIC yields accurate estimate of the target locations with considerable noise and multiple scattering in the received signals.
Abstract: Monitoring lightning electromagnetic pulses (sferics)
and other terrestrial as well as extraterrestrial transient radiation signals
is of considerable interest for practical and theoretical purposes
in astro- and geophysics as well as meteorology. Managing a continuous
flow of data, automisation of the detection and classification
process is important. Features based on a combination of wavelet and
statistical methods proved efficient for analysis and characterisation
of transients and as input into a radial basis function network that is
trained to discriminate transients from pulse like to wave like.
Abstract: This paper presents a method for functional projective H∞ synchronization problem of chaotic systems with external disturbance. Based on Lyapunov theory and linear matrix inequality (LMI) formulation, the novel feedback controller is established to not only guarantee stable synchronization of both drive and response systems but also reduce the effect of external disturbance to an H∞ norm constraint.
Abstract: This paper discusses a genetic algorithm (GA) based optimal load shedding that can apply for electrical distribution networks with and without dispersed generators (DG). Also, the proposed method has the ability for considering constant and variable capacity deficiency caused by unscheduled outages in the bulked generation and transmission system of bulked power supply. The genetic algorithm (GA) is employed to search for the optimal load shedding strategy in distribution networks considering DGs in two cases of constant and variable modelling of bulked power supply of distribution networks. Electrical power distribution systems have a radial network and unidirectional power flows. With the advent of dispersed generations, the electrical distribution system has a locally looped network and bidirectional power flows. Therefore, installed DG in the electrical distribution systems can cause operational problems and impact on existing operational schemes. Introduction of DGs in electrical distribution systems has introduced many new issues in operational and planning level. Load shedding as one of operational issue has no exempt. The objective is to minimize the sum of curtailed load and also system losses within the frame-work of system operational and security constraints. The proposed method is tested on a radial distribution system with 33 load points for more practical applications.
Abstract: The breakdown strength characteristic of Low Density
Polyethylene films (LDPE) under DC voltage application and the
effect of water absorption have been studied. Mainly, our experiment
was investigated under two conditions; dry and heavy water
absorption. Under DC ramp voltage, the result found that the
breakdown strength under heavy water absorption has a lower value
than dry condition. In order to clarify the effect, the temperature rise of
film was observed using non contact thermograph until the occurrence
of the electrical breakdown and the conduction current of the sample
was also measured in correlation with the thermograph measurement.
From the observations, it was shown that under the heavy water
absorption, the hot spot in the samples appeared at lower voltage. At
the same voltage the temperature of the hot spot and conduction
current was higher than that under the dry condition. The measurement
result has a good correlation between the existence of a critical field
for conduction current and thermograph observation. In case of the
heavy water absorption, the occurrence of the threshold field was
earlier than the dry condition as result lead to higher of conduction
current and the temperature rise appears after threshold field was
significantly increased in increasing of field. The higher temperature
rise was caused by the higher current conduction as the result the
insulation leads to breakdown to the lower field application.
Abstract: To study on effect of PEG and NaCl stress on
germination and early seedling stages on two cultivar of corn, two
separated experiment were laid out at physiology laboratory, faculty
of Agriculture, Razi University, Kermanshah, Iran in 2009. This
investigation was performed as factorial experiment under Complete
Randomized Design (CRD) with three replications. Cultivar factor
contains of two varieties (sweet corn SC403 and Flint corn SC704)
and five levels of stress (0, -2, -4, -6 and -8 bar). The principal aim of
current study was to compare the two varieties of maize in relative to
the stress conditions. Results indicated that significant decrease was
observed in percentage of germination, germination rate, length of
radicle and plumule and radicle and plumule dry matter. On the basis
of the results, NaCl as compared with PEG had more effect on
germination and early seedling stage and sweet corn had more
resistant than flint corn in both stress conditions.
Abstract: The purpose of the experiments described in this article was the comparison of integrated fixed film activated sludge (IFAS) and activated sludge (AS) system. The IFAS applied system consists of the cigarette filter rods (wasted filter in tobacco factories) as a biofilm carrier. The comparison with activated sludge was performed by two parallel treatment lines. Organic substance, ammonia and TP removal was investigated over four month period. Synthetic wastewater was prepared with ordinary tap water and glucose as the main sources of carbon and energy, plus balanced macro and micro nutrients. COD removal percentages of 94.55%, and 81.62% were achieved for IFAS and activated sludge system, respectively. Also, ammonia concentration significantly decreased by increasing the HRT in both systems. The average ammonia removal of 97.40 % and 96.34% were achieved for IFAS and activated sludge system, respectively. The removal efficiency of total phosphorus (TP-P) was 60.64%, higher than AS process by 56.63% respectively.
Abstract: Biological data has several characteristics that strongly differentiate it from typical business data. It is much more complex, usually large in size, and continuously changes. Until recently business data has been the main target for discovering trends, patterns or future expectations. However, with the recent rise in biotechnology, the powerful technology that was used for analyzing business data is now being applied to biological data. With the advanced technology at hand, the main trend in biological research is rapidly changing from structural DNA analysis to understanding cellular functions of the DNA sequences. DNA chips are now being used to perform experiments and DNA analysis processes are being used by researchers. Clustering is one of the important processes used for grouping together similar entities. There are many clustering algorithms such as hierarchical clustering, self-organizing maps, K-means clustering and so on. In this paper, we propose a clustering algorithm that imitates the ecosystem taking into account the features of biological data. We implemented the system using an Ant-Colony clustering algorithm. The system decides the number of clusters automatically. The system processes the input biological data, runs the Ant-Colony algorithm, draws the Topic Map, assigns clusters to the genes and displays the output. We tested the algorithm with a test data of 100 to1000 genes and 24 samples and show promising results for applying this algorithm to clustering DNA chip data.
Abstract: The purposes of this research are: 1) to study the media
literacy of early teenagers, and 2) to study the interaction between
gender and timing of media exposure that affects the media literacy
of teenagers. The sample of the study included 400 young people
aged between 11 to 17 and who were living in Bangkok. The data
was collected using questionnaires. Two-way ANOVA was used in
analyzing the collected data. The result revealed that gender and
timing of media exposure affected the media literacy of early
teenagers with statistical significance at the level of 0.05.
Abstract: International markets driven forces are changing
continuously, therefore companies need to gain a competitive edge in
such markets. Improving the company's products, processes and
practices is no longer auxiliary. Lean production is a production
management philosophy that consolidates work tasks with minimum
waste resulting in improved productivity. Lean production practices
can be mapped into many production areas. One of these is
Manufacturing Equipment and Technology (MET). Many lean
production practices can be implemented in MET, namely, specific
equipment configurations, total preventive maintenance, visual
control, new equipment/ technologies, production process
reengineering and shared vision of perfection.The purpose of this
paper is to investigate the implementation level of these six practices
in Jordanian industries. To achieve that a questionnaire survey has
been designed according to five-point Likert scale. The questionnaire
is validated through pilot study and through experts review. A sample
of 350 Jordanian companies were surveyed, the response rate was
83%. The respondents were asked to rate the extent of
implementation for each of practices. A relationship conceptual
model is developed, hypotheses are proposed, and consequently the
essential statistical analyses are then performed. An assessment tool
that enables management to monitor the progress and the
effectiveness of lean practices implementation is designed and
presented. Consequently, the results show that the average
implementation level of lean practices in MET is 77%, Jordanian
companies are implementing successfully the considered lean
production practices, and the presented model has Cronbach-s alpha
value of 0.87 which is good evidence on model consistency and
results validation.
Abstract: There are different kinds of online systems on the Internet for people who need support and develop new knowledge. Online communities and Ask the Expert systems are two such systems. In the health care area, the number of users of these systems has increased at a rapid pace. Interactions with medical trained experts take place online, and people with concerns about similar health problems come together to share experiences and advice. The systems are also used as storages and browsed for health information. Over the years, studies have been conducted of the usage of the different systems. However, in what ways the systems can be used together to enhance learning has not been explored. This paper presents results from a study of online health-communities and an Ask the Expert system for people who suffer from overweight. Differences and similarities in regards to posted issues and replies are discussed, and suggestions for a new holistic design of the two systems are presented.
Abstract: Self-organizing map (SOM) provides both clustering and visualization capabilities in mining data. Dynamic self-organizing maps such as Growing Self-organizing Map (GSOM) has been developed to overcome the problem of fixed structure in SOM to enable better representation of the discovered patterns. However, in mining large datasets or historical data the hierarchical structure of the data is also useful to view the cluster formation at different levels of abstraction. In this paper, we present a technique to generate concept trees from the GSOM. The formation of tree from different spread factor values of GSOM is also investigated and the quality of the trees analyzed. The results show that concept trees can be generated from GSOM, thus, eliminating the need for re-clustering of the data from scratch to obtain a hierarchical view of the data under study.
Abstract: Biodiesel is traditionally produced from oleaginous
plants. On the other hand, increasing biodiesel production from these
raw materials could create problems of food supply. Producing
biodiesel from microalgae could help to overcome this difficulty,
because microalgae are rich in lipids and do not compete for arable
lands. However, no studies had compared vegetable and microalgae
oil-based biodiesel in terms of yield, viscosity and heat of
combustion. In the present study, commercial canola and microalgae
oil were therefore transesterified with methanol under a homogenous
alkali catalyst (potassium hydroxide) at 100oC for 1h. The result
showed that microalgae-based oil has a higher yield in biodiesel with
89.7% (g biodiesel/g oil) and a lower kinematic viscosity (22oC) of
4.31 mm/s2 than canola oil.
Abstract: Sedimentation formation is a complex hydraulic phenomenon that has emerged as a major operational and maintenance consideration in modern hydraulic engineering in general and river engineering in particular. Sediments accumulation along the river course and their eventual storage in a form of islands affect water intake in the canal systems that are fed by the storage reservoirs. Without proper management, sediment transport can lead to major operational challenges in water distribution system of arid regions like the Dez and Hamidieh command areas. The paper aims to investigate sedimentation in the Western Canal of Dez Diversion Weir using the SHARC model and compare the results with the two intake structures of the Hamidieh dam in Iran using SSIIM model. The objective was to identify the factors which influence the process, check reliability of outcome and provide ways in which to mitigate the implications on operation and maintenance of the structures. Results estimated sand and silt bed loads concentrations to be 193 ppm and 827ppm respectively. This followed ,ore or less similar pattern in Hamidieh where the sediment formation impeded water intake in the canal system. Given the available data on average annual bed loads and average suspended sediment loads of 165ppm and 837ppm in the Dez, there was a significant statistical difference (16%) between the sand grains, whereas no significant difference (1.2%) was find in the silt grain sizes. One explanation for such finding being that along the 6 Km river course there was considerable meandering effects which explains recent shift in the hydraulic behavior along the stream course under investigation. The sand concentration in downstream relative to present state of the canal showed a steep descending curve. Sediment trapping on the other hand indicated a steep ascending curve. These occurred because the diversion weir was not considered in the simulation model. The comparative study showed very close similarities in the results which explains the fact that both software can be used as accurate and reliable analytical tools for simulation of the sedimentation in hydraulic engineering.