Abstract: We constructed a method of noise reduction for
JPEG-compressed image based on Bayesian inference using the
maximizer of the posterior marginal (MPM) estimate. In this method,
we tried the MPM estimate using two kinds of likelihood, both of
which enhance grayscale images converted into the JPEG-compressed
image through the lossy JPEG image compression. One is the
deterministic model of the likelihood and the other is the probabilistic
one expressed by the Gaussian distribution. Then, using the Monte
Carlo simulation for grayscale images, such as the 256-grayscale
standard image “Lena" with 256 × 256 pixels, we examined the
performance of the MPM estimate based on the performance measure
using the mean square error. We clarified that the MPM estimate via
the Gaussian probabilistic model of the likelihood is effective for
reducing noises, such as the blocking artifacts and the mosquito noise,
if we set parameters appropriately. On the other hand, we found that
the MPM estimate via the deterministic model of the likelihood is not
effective for noise reduction due to the low acceptance ratio of the
Metropolis algorithm.
Abstract: This study examined the effects of 8-week Pilates training program on limits of stability (LOS) and abdominal muscle strength in young dancers. Twenty-four female volunteered and randomly assigned as experimental group (EG) or control group (CG). All subjects received the same dance lessons but the EG underwent an extra Pilates mat exercises for 40 minutes, three times a week, for 8 weeks. LOS was evaluated by the Biodex Balance System and the abdominal strength was measured by 30/60 seconds sit-ups test. One factor ANCOVA was used to examine the differences between groups after training. The results showed that the overall LOS scores at levels 2/8 and the 30/60 seconds sit-ups for the EG group pre- and post-training were changed from 22/38 % to 31/51 % and 20/33 times to 24/42 times, respectively. The study demonstrated that 8-week Pilates training can improve the LOS performance and abdominal strength in young dancers.
Abstract: This study was conducted to investigate the optimum
levels of glutamine (Gln) supplementation in broiler diets. A total of
32 one-day-old male chicks with initial body weight 41.5 g were
segregated into 4 groups (8 chicks per group) and subsequently
distributed to individual cages. Feed and water were provided ad
libitum for 21 days. Four dietary treatments were as follows: control
and supplemented Gln at 1, 2 and 3%, respectively. The results found
that the addition Gln had no negative effects on dry matter, organic
matter, ash digestibility or nitrogen retention. Birds fed with 1% Gln
had significantly higher villi wide and villi height : crypt depth ratio
in duodenum than the control chicks and 2 and 3% Gln chicks. It is
suggested that the addition of Gln at 1% indicated a beneficial effect
on improving small intestinal morphology, in addition Gln may
stimulate immune organ development of broiler chickens.
Abstract: This paper presents the results of corrosion fatigue
crack growth behaviour of a Ni-Cr-Mn steel commonly used in
marine applications. The effect of mechanical variables such as
frequency and load ratio on fatigue crack growth rate at various
stages has been studied using compact tension (C(T)) specimens
along the rolling direction of steel plate under 3.5% saturated NaCl
aqueous environment. The significance of crack closure on corrosion
fatigue, and the validity of Elber-s empirical linear crack closure
model with the ASTM compliance offset method have been
examined.
Fatigue crack growth rate is higher and threshold stress intensities
are lower in aqueous environment compared to the lab air conditions.
It is also observed that the crack growth rate increases at lower
frequencies. The higher stress ratio promotes the crack growth. The
effect of oxidization and corrosion pit formation is very less as the
stress ratio is increased. It is observed that as stress ratios are
increased, the Elber-s crack closure model agrees well with the crack
closure estimated by the ASTM compliance offset method for tests
conducted at 5Hz frequency compared to tests conducted at 1Hz in
corrosive environment.
Abstract: This paper aims to describe how student satisfaction is
measured for work-based learners as these are non-traditional
learners, conducting academic learning in the workplace, typically
their curricula have a high degree of negotiation, and whose
motivations are directly related to their employers- needs, as well as
their own career ambitions. We argue that while increasing WBL
participation, and use of SSD are both accepted as being of strategic
importance to the HE agenda, the use of WBL SSD is rarely
examined, and lessons can be learned from the comparison of SSD
from a range of WBL programmes, and increased visibility of this
type of data will provide insight into ways to improve and develop
this type of delivery. The key themes that emerged from the analysis
of the interview data were: learners profiles and needs, employers
drivers, academic staff drivers, organizational approach, tools for
collecting data and visibility of findings. The paper concludes with
observations on best practice in the collection, analysis and use of
WBL SSD, thus offering recommendations for both academic
managers and practitioners.
Abstract: This paper explores the social and political imperatives in the sphere of public policy relating to social justice. In India, the colonial legacy and post-colonial social and political pressures sustained the appropriation of 'caste' category in allocating public resources to the backward class of citizens. For several reasons, 'economic' category could not be placed in allocating resources. This paper examines the reasons behind the deliberative exercises and formulating policies and seeks an alternative framework in realizing social justice in terms of a unified category. This attempt can be viewed as a reconciliation of traditional and modern values for a viable alternative in public policy making.
Abstract: Laser engraving is a manufacturing method for those applications where previously Electrical Discharge Machining (EDM) was the only choice. Laser engraving technology removes material layer-by-layer and the thickness of layers is usually in the range of few microns. The aim of the present work is to investigate the influence of the process parameters on the surface quality when machined by laser engraving. The examined parameters were: the pulse frequency, the beam speed and the layer thickness. The surface quality was determined by the surface roughness for every set of parameters. Experimental results on Al7075 material showed that the surface roughness strictly depends on the process parameters used.
Abstract: This study examines knowledge management in the public organizations in Iran. The purpose of this article is to provide a conceptual framework for application of knowledge management in public organizations. The study indicates that an increasing tendency for implementation of knowledge management in organizations is emerging. Nonetheless knowledge management in public organizations is toddler and little has been done to bring the subject to use in the public sector. The globalization of change and popularization of some values like participation, citizen-orientation and knowledge-orientation in the new theories of public administration requires that the knowledge management is considered and attend to in the public sector. This study holds that a knowledge management framework for public organizations is different from this in the public sector, because public sector is stakeholder-dependent while the private is shareholder-dependent. Based on the research, we provide a conceptual model. The model proposed involves three factors: Organizational, knowledge citizens and contextual factors. The study results indicate these factors affect on knowledge management in public organizations in Iran.
Abstract: Megalopolis is a group of densely populated metropolitan areas that combine to form an urban complex. Since China introduced the economic reforms in late 1970s, the Chinese urban system has experienced unprecedented growth. The process of urbanisation prevailed in the 1980s, and the process of predominantly large city growth appeared to continue through 1990s and 2000s. In this study, the magnitude and pattern of urbanisation in China during 1990s were examined using remotely sensed imagery acquired by TM/ETM+ sensor onboard the Landsat satellites. The development of megalopolis areas in China was also studied based on the GIS analysis of the increases of urban and built-up area from 1990 to 2000. The analysis suggests that in the traditional agricultural zones in China, e.g., Huang-Huai-Hai Plains, Changjiang River Delta, Pearl River Delta and Sichuan Basin, the urban and built-up areas increased by 1.76 million hectares, of which 0.82 million hectares are expansion of urban areas, an increase of 24.78% compared with 1990 at the national scale. The Yellow River Delta, Changjiang River Delta and Pearl River Delta also saw an increase of urban and built-up area by 63.9%, 66.2% and 83.0% respectively. As a result, three major megalopolises were developed in China: the Guangzhou-Shenzhen-Hong Kong- Macau (Pearl River Delta: PRD) megalopolis area, the Shanghai- Nanjing-Hangzhou (Changjiang River Delta: CRD) megalopolis area and the Beijing-Tianjing-Tangshan-Qinhuangdao (Yellow River Delta-Bohai Sea Ring: YRD) megalopolis area. The relationship between the processed of megalopolisation and the inter-provincial population flow was also explored in the context of social-economic and transport infrastructure development in Post-reform China.
Abstract: The present article deals with a composite casting process that allows to produce bilayer AlSn6-Al strips based on the technique of horizontal continuous casting. In the first part experimental investigations on the production of a single layer AlSn6 strip are described. Afterwards essential results of basic compound casting trials using simple test specimen are presented to define the thermal conditions required for a metallurgical compound between the alloy AlSn6 and pure aluminium. Subsequently, numerical analyses are described. A finite element model was used to examine a continuous composite casting process. As a result of the simulations the main influencing parameters concerning the thermal conditions within the composite casting region could be pointed out. Finally, basic guidance is given for the design of an appropriate composite mould system.
Abstract: This paper presents the combination of different precipitation data sets and the distributed hydrological model, in order to examine the flood runoff reproductivity of scattered observation catchments. The precipitation data sets were obtained from observation using rain-gages, satellite based estimate (TRMM), and numerical weather prediction model (NWP), then were coupled with the super tank model. The case study was conducted in three basins (small, medium, and large size) located in Central Vietnam. Calculated hydrographs based on ground observation rainfall showed best fit to measured stream flow, while those obtained from TRMM and NWP showed high uncertainty of peak discharges. However, calculated hydrographs using the adjusted rainfield depicted a promising alternative for the application of TRMM and NWP in flood modeling for scattered observation catchments, especially for the extension of forecast lead time.
Abstract: One of the major challenges in the Information
Retrieval field is handling the massive amount of information
available to Internet users. Existing ranking techniques and strategies
that govern the retrieval process fall short of expected accuracy.
Often relevant documents are buried deep in the list of documents
returned by the search engine. In order to improve retrieval accuracy
we examine the issue of language effect on the retrieval process.
Then, we propose a solution for a more biased, user-centric relevance
for retrieved data. The results demonstrate that using indices based
on variations of the same language enhances the accuracy of search
engines for individual users.
Abstract: This survey of recent literature examines the link between growth and poverty. It is widely accepted that economic growth is a necessary condition for sustainable poverty reduction. But it is the fact that the economic growth of some countries has been pro-poor while others not. Some factors such as labor market, policies and demographic factors may lead to a weak relationship between economic performance and poverty rate. In this sense pro-growth policies should be pro-poor to increase the poverty alleviation effects of the growth. The purpose of this study is to review the recent studies on the effects of macroeconomic policies on poverty and inequality and to review the poverty analyses which examine the relationship between growth, poverty and inequality. Also this study provides some facts about the relationship between economic growth, inequality and poverty from Turkey. Keywordseconomic growth, inequality, macroeconomic policy, poverty
Abstract: The main thrust of this paper is to assess the level of disclosure in the annual reports of non-financial Greek firms and to empirically investigate the hypothesized impact of several firm characteristics on the extent of mandatory disclosure. A disclosure checklist consisting of 100 mandatory items was developed to assess the level of disclosure in the 2009 annual reports of 43 Greek companies listed at the Athens stock exchange. The association between the level of disclosure and some firm characteristics was examined using multiple linear regression analysis. The study reveals that Greek companies on general have responded adequately to the mandatory disclosure requirements of the regulatory bodies. The findings also indicate that firm size was significant positively associated with the level of disclosure. The remaining variables such as age, profitability, liquidity, and board composition were found to be insignificant in explaining the variation of mandatory disclosures. The outcome of this study is undoubtedly of great concern to the investment community at large to assist in evaluating the extent of mandatory disclosure by Greek firms and explaining the variation of disclosure in light of firm-specific characteristics.
Abstract: Professional development is the focus of this study. It
reports on questionnaire data that examined the perceived
effectiveness of the Train the Trainer model of technology
professional development for elementary teachers. Eighty-three
selected teachers called Information Technology Coaches received
four half-day and one after-school in-service sessions. Subsequently,
coaches shared the information and skills acquired during training
with colleagues. Results indicated that participants felt comfortable
as Information Technology Coaches and felt well prepared because
of their technological professional development. Overall, participants
perceived the Train the Trainer model to be effective. The outcomes
of this study suggest that the use of the Train the Trainer model, a
known professional development model, can be an integral and
interdependent component of the newer more comprehensive
learning community professional development model.
Abstract: Internet application in China has maintained a constant
development tendency in the past decade. China is now one of the
most populous countries in terms of internet user population. While
offering enormous opportunities, the dramatic digitalization also
brings about a series of challenges that demand urgent attention.
Digital divide is one of the challenges that affect China as well as other
countries in the world. This paper examines digital divide in the
Chinese context from the perspective of development communication.
Through a case study of a rural township under the backdrop of the
rapid internet development in China, the paper discusses the
economic, psychological and cultural roots of digital divide; and
explores development communication strategies addressing the roots
of digital divide. It is argued that development communication must be
responsive to the potentialities and preferences of the specific society
and serve the purposes of participation and sustainability.
Abstract: As we know, most differential equations concerning
physical phenomenon could not be solved by analytical method. Even if we use Series Method, some times we need an appropriate change of variable, and even when we can, their closed form solution may be
so complicated that using it to obtain an image or to examine the structure of the system is impossible. For example, if we consider Schrodinger equation, i.e.,
We come to a three-term recursion relations, which work with it takes, at least, a little bit time to get a series solution[6]. For this
reason we use a change of variable such as or when we consider the orbital angular momentum[1], it will be
necessary to solve. As we can observe, working with this equation is tedious. In this paper, after introducing Clenshaw method, which is a kind of Spectral method, we try to solve some of such equations.
Abstract: The use of 3D computer-aided design (CAD) models
to support construction project planning has been increasing in the
previous year. 3D CAD models reveal more planning ideas by
visually showing the construction site environment in different stages
of the construction process. Using 3D CAD models together with
scheduling software to prepare construction plan can identify errors
in process sequence and spatial arrangement, which is vital to the
success of a construction project. A number of 4D (3D plus time)
CAD tools has been developed and utilized in different construction
projects due to the awareness of their importance. Virtual prototyping
extends the idea of 4D CAD by integrating more features for
simulating real construction process. Virtual prototyping originates
from the manufacturing industry where production of products such
as cars and airplanes are virtually simulated in computer before they
are built in the factory. Virtual prototyping integrates 3D CAD,
simulation engine, analysis tools (like structural analysis and
collision detection), and knowledgebase to streamline the whole
product design and production process. In this paper, we present the
application of a virtual prototyping software which has been used in
a few construction projects in Hong Kong to support construction
project planning. Specifically, the paper presents an implementation
of virtual prototyping in a residential building project in Hong Kong.
The applicability, difficulties and benefits of construction virtual
prototyping are examined based on this project.
Abstract: The demands of taller structures are becoming imperative almost everywhere in the world in addition to the challenges of material and labor cost, project time line etc. This paper conducted a study keeping in view the challenging nature of high-rise construction with no generic rules for deflection minimizations and frequency control. The effects of cyclonic wind and provision of outriggers on 28-storey, 42-storey and 57-storey are examined in this paper and certain conclusions are made which would pave way for researchers to conduct further study in this particular area of civil engineering. The results show that plan dimensions have vital impacts on structural heights. Increase of height while keeping the plan dimensions same, leads to the reduction in the lateral rigidity. To achieve required stiffness increase of bracings sizes as well as introduction of additional lateral resisting system such as belt truss and outriggers is required.
Abstract: This article addresses the procedures to validate the Arabic version of Multiple Intelligence Development Assessment Scale (MIDAS). The content validity was examined based on the experts- judgments on the MIDAS-s items in the Arabic version. The content of eleven items in the Arabic version of MIDAS was modified to match the Arabic context. Then a translation from original English version of MIDAS into Arabic language was performed. The reliability of the Arabic MIDAS was calculated based on test and retest method and found to be 0.85 for the overall MIDAS and for the different subscales ranging between 0.78 - 0.87. The examination of construct validity for the overall Arabic MIDAS and its subscales was established by using Winsteps program version 6 based on Rasch model in order to fit the items into the Arabic context. The findings indicated that, the eight subscales in Arabic version of MIDAS scale have a unidimensionality, and the total number of kept items in the overall scale is 108 items.