Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: This paper describes the development of a 16-ports optical code division multiple access (OCDMA) encoder prototype based on Arrayed Waveguide Grating (AWG) and optical switches. It is potentially to provide a high security for data transmission due to all data will be transmitted in binary code form. The output signals from AWG are coded with a binary code that given to an optical switch before it signal modulate with the carrier and transmitted to the receiver. The 16-ports encoder used 16 double pole double throw (DPDT) toggle switches to control the polarization of voltage source from +5 V to -5 V for 16 optical switches. When +5 V is given, the optical switch will give code '1' and vice versa. The experimental results showed the insertion loss, crosstalk, uniformity, and optical signal-noise-ratio (OSNR) for the developed prototype are
Abstract: A method is presented for using thermo-mechanical fatigue analysis as a tool in the design of automotive heat exchangers. Use of infra-red thermography to measure the real thermal history in the heat exchanger reduces the time necessary for calculating design parameters and improves prediction accuracy. Thermal shocks are the primary cause of heat exchanger damage. Thermo-mechanical simulation is based on the mean behavior of the aluminum tubes used in the heat exchanger. An energetic fatigue criterion is used to detect critical zones.
Abstract: The nature, prevalence, cellular composition of
leukocyte infiltrates and immunohistochemical characteristics of
their constituent cells in the liver of patients with chronic viral
hepatitis B and C were investigated. It was found that the area of
distribution and cellular composition of infiltrates depended on the
virus type and process activity. The expediency of
immunohistochemical study using leukocyte infiltrates from liver
biopsies of patients with viral hepatitis aimed at clarifying diagnosis,
making prognosis, and choice of optimal treatment with elements of
immune correction is emphasized.
Abstract: This paper presents a spectroscopic study on doping
of Vanadyl pathalocyanine (VOPc) by [6,6]-phenyl C61 butyric acid
methyl ester (PCBM). The films are characterized by UV/Vis/NIR
spectroscopy. A drastic increase in the absorption coefficient has
been observed with increasing dopant concentration. Optical
properties of VOPc:PCBM films deposited by spin coating technique
were studied in detail. Optical band gap decreased with the PCBM
incorporation in the VOPc film. Optical band gap calculated from the
absorption spectra decreased from 3.32 eV to 3.26 eV with a
variation of 0–75 % of PCBM concentration in the VOPC films.
Abstract: Water quality is a subject of ongoing concern.
Deterioration of water quality has initiated serious management
efforts in many countries. This study endeavors to automatically
classify water quality. The water quality classes are evaluated using 6
factor indices. These factors are pH value (pH), Dissolved Oxygen
(DO), Biochemical Oxygen Demand (BOD), Nitrate Nitrogen
(NO3N), Ammonia Nitrogen (NH3N) and Total Coliform (TColiform).
The methodology involves applying data mining
techniques using multilayer perceptron (MLP) neural network
models. The data consisted of 11 sites of canals in Dusit district in
Bangkok, Thailand. The data is obtained from the Department of
Drainage and Sewerage Bangkok Metropolitan Administration
during 2007-2011. The results of multilayer perceptron neural
network exhibit a high accuracy multilayer perception rate at 96.52%
in classifying the water quality of Dusit district canal in Bangkok
Subsequently, this encouraging result could be applied with plan and
management source of water quality.
Abstract: The study on the tree growth for four species groups of commercial timber in Koh Kong province, Cambodia-s tropical rainforest is described. The simulation for these four groups had been successfully developed in the 5-year interval through year-60. Data were obtained from twenty permanent sample plots in the duration of thirteen years. The aim for this study was to develop stand table simulation system of tree growth by the species group. There were five steps involved in the development of the tree growth simulation: aggregate the tree species into meaningful groups by using cluster analysis; allocate the trees in the diameter classes by the species group; observe the diameter movement of the species group. The diameter growth rate, mortality rate and recruitment rate were calculated by using some mathematical formula. Simulation equation had been created by combining those parameters. Result showed the dissimilarity of the diameter growth among species groups.
Abstract: Campus sustainability is the goal of a university striving for sustainable development. This study found that of 17 popular approaches, two comprehensive campus sustainability assessment frameworks were developed in the context of Sustainability in Higher Education (SHE), and used by many university campuses around the world. Sustainability Tracking Assessment and Rating Systems (STARS) and the Campus Sustainability Assessment Framework (CSAF) approaches are more comprehensive than others. Therefore, the researchers examined aspects and elements used by CSAF and STARS in the approach to develop a campus sustainability assessment framework for Universiti Kebangsaan Malaysia (UKM). Documents analysis found that CSAF and STARS do not focus on physical development, especially the construction industry, as key elements of campus sustainability assessment. This finding is in accordance with the Sustainable UKM Programme which consists of three main components of sustainable community, ecosystem and physical development.
Abstract: Present wireless communication demands compact and intelligent devices with multitasking capabilities at affordable cost. The focus in the presented paper is on a dual band antenna for wireless communication with the capability of operating at two frequency bands with same structure. Two resonance frequencies are observed with the second operation band at 4.2GHz approximately three times the first resonance frequency at 1.5GHz. Structure is simple loop of microstrip line with characteristic impedance 50 ohms. The proposed antenna is designed using defective ground structure (DGS) and shows the nearly one third reductions in size as compared to without DGS. This antenna was simulated on electromagnetic (EM) simulation software and fabricated using microwave integrated circuit technique on RT-Duroid dielectric substrate (εr= 2.22) of thickness (H=15 mils). The designed antenna was tested on automatic network analyzer and shows the good agreement with simulated results. The proposed structure is modeled into an equivalent electrical circuit and simulated on circuit simulator. Subsequently, theoretical analysis was carried out and simulated. The simulated, measured, equivalent circuit response, and theoretical results shows good resemblance. The bands of operation draw many potential applications in today’s wireless communication.
Abstract: In biological and biomedical research motif finding tools are important in locating regulatory elements in DNA sequences. There are many such motif finding tools available, which often yield position weight matrices and significance indicators. These indicators, p-values and E-values, describe the likelihood that a motif alignment is generated by the background process, and the expected number of occurrences of the motif in the data set, respectively. The various tools often estimate these indicators differently, making them not directly comparable. One approach for comparing motifs from different tools, is computing the E-value as the product of the p-value and the number of possible alignments in the data set. In this paper we explore the combinatorics of the motif alignment models OOPS, ZOOPS, and ANR, and propose a generic algorithm for computing the number of possible combinations accurately. We also show that using the wrong alignment model can give E-values that significantly diverge from their true values.
Abstract: Avoiding learning failures in mathematics e-learning environments caused by emotional problems in students with autism has become an important topic for combining of special education with information and communications technology. This study presents an adaptive emotional adjustment model in mathematics e-learning for students with autism, emphasizing the lack of emotional perception in mathematics e-learning systems. In addition, an emotion classification for students with autism was developed by inducing emotions in mathematical learning environments to record changes in the physiological signals and facial expressions of students. Using these methods, 58 emotional features were obtained. These features were then processed using one-way ANOVA and information gain (IG). After reducing the feature dimension, methods of support vector machines (SVM), k-nearest neighbors (KNN), and classification and regression trees (CART) were used to classify four emotional categories: baseline, happy, angry, and anxious. After testing and comparisons, in a situation without feature selection, the accuracy rate of the SVM classification can reach as high as 79.3-%. After using IG to reduce the feature dimension, with only 28 features remaining, SVM still has a classification accuracy of 78.2-%. The results of this research could enhance the effectiveness of eLearning in special education.
Abstract: A gene network gives the knowledge of the regulatory
relationships among the genes. Each gene has its activators and
inhibitors that regulate its expression positively and negatively
respectively. Genes themselves are believed to act as activators and
inhibitors of other genes. They can even activate one set of genes and
inhibit another set. Identifying gene networks is one of the most
crucial and challenging problems in Bioinformatics. Most work done
so far either assumes that there is no time delay in gene regulation or
there is a constant time delay. We here propose a Dynamic Time-
Lagged Correlation Based Method (DTCBM) to learn the gene
networks, which uses time-lagged correlation to find the potential
gene interactions, and then uses a post-processing stage to remove
false gene interactions to common parents, and finally uses dynamic
correlation thresholds for each gene to construct the gene network.
DTCBM finds correlation between gene expression signals shifted in
time, and therefore takes into consideration the multi time delay
relationships among the genes. The implementation of our method is
done in MATLAB and experimental results on Saccharomyces
cerevisiae gene expression data and comparison with other methods
indicate that it has a better performance.
Abstract: In this research work, poly (acrylonitrile-butadienestyrene)/
polypropylene (ABS/PP) blends were processed by melt
compounding in a twin-screw extruder. Upgrading of the thermal
characteristics of the obtained materials was attempted by the
incorporation of organically modified montmorillonite (OMMT), as
well as, by the addition of two types of compatibilizers;
polypropylene grafted with maleic anhydride (PP-g-MAH) and ABS
grafted with maleic anhydride (ABS-g-MAH). The effect of the
above treatments was investigated separately and in combination.
Increasing the PP content in ABS matrix seems to increase the
thermal stability of their blend and the glass transition temperature
(Tg) of SAN phase of ABS. From the other part, the addition of ABS
to PP promotes the formation of its β-phase, which is maximum at 30
wt% ABS concentration, and increases the crystallization temperature
(Tc) of PP. In addition, it increases the crystallization rate of PP.The
β-phase of PP in ABS/PP blends is reduced by the addition of
compatibilizers or/and organoclay reinforcement. The incorporation
of compatibilizers increases the thermal stability of PP and reduces
its melting (ΔΗm) and crystallization (ΔΗc) enthalpies. Furthermore it
decreases slightly the Tgs of PP and SAN phases of ABS/PP blends.
Regarding the storage modulus of the ABS/PP blends, it presents a
change in their behavior at about 10°C and return to their initial
behavior at ~110°C. The incorporation of OMMT to no compatibilized
and compatibilized ABS/PP blends enhances their storage modulus.
Abstract: Robustness is one of the primary performance criteria for an Intelligent Video Surveillance (IVS) system. One of the key factors in enhancing the robustness of dynamic video analysis is,providing accurate and reliable means for shadow detection. If left undetected, shadow pixels may result in incorrect object tracking and classification, as it tends to distort localization and measurement information. Most of the algorithms proposed in literature are computationally expensive; some to the extent of equalling computational requirement of motion detection. In this paper, the homogeneity property of shadows is explored in a novel way for shadow detection. An adaptive division image (which highlights homogeneity property of shadows) analysis followed by a relatively simpler projection histogram analysis for penumbra suppression is the key novelty in our approach.
Abstract: This work aims to describe the process of developing
services and applications of seamless communication within a
Telecom Italia long-term research project, which takes as central aim
the design of a wearable communication device. In particular, the
objective was to design a wrist phone integrated into everyday life of
people in full transparency. The methodology used to design the
wristwatch was developed through several subsequent steps also
involving the Personas Layering Framework. The data collected in
this phases have been very useful for designing an improved version
of the first two concepts of wrist phone going to change aspects
related to the four critical points expressed by the users.
Abstract: Texture classification is an important image processing
task with a broad application range. Many different techniques for
texture classification have been explored. Using sparse approximation
as a feature extraction method for texture classification is a relatively
new approach, and Skretting et al. recently presented the Frame
Texture Classification Method (FTCM), showing very good results on
classical texture images. As an extension of that work the FTCM is
here tested on a real world application as detection of abnormalities
in mammograms. Some extensions to the original FTCM that are
useful in some applications are implemented; two different smoothing
techniques and a vector augmentation technique. Both detection of
microcalcifications (as a primary detection technique and as a last
stage of a detection scheme), and soft tissue lesions in mammograms
are explored. All the results are interesting, and especially the results
using FTCM on regions of interest as the last stage in a detection
scheme for microcalcifications are promising.
Abstract: The aim of this paper is to study in depth some methodological aspects of social interventation, focusing on desirable passage from social maternage method to peer advocacy method. For this purpose, we intend analyze social and organizative components, that affect operator's professional action and that are part of his psychological environment, besides the physical and social one. In fact, operator's interventation should not be limited to a pure supply of techniques, nor to take shape as improvised action, but “full of good purposes".
Abstract: The effect of artificial pozzolan (waste brick) on the
physico-chemical properties of cement manufactured was
investigated. The waste brick is generated by the manufacture of
bricks. It was used in the proportions of 0%, 5%, 10%, 15% and 20%
by mass of cement to study its effect on the physico-chemical
properties of cement incorporating artificial pozzolan. The physicochemical
properties of cement at anhydrous state and the hydrated
state (chemical composition, specific weight, fineness, consistency of
the cement paste and setting times) were studied. The experimental
results obtained show that the quantity of pozzolanic admixture
(waste brick) of cement manufactured is the principal parameter who
influences on the variation of the physico-chemical properties of the
cement tested.
Abstract: The main objective developed in this paper is to find a
graphic technique for modeling, simulation and diagnosis of the
industrial systems. This importance is much apparent when it is about
a complex system such as the nuclear reactor with pressurized water
of several form with various several non-linearity and time scales. In
this case the analytical approach is heavy and does not give a fast
idea on the evolution of the system. The tool Bond Graph enabled us
to transform the analytical model into graphic model and the
software of simulation SYMBOLS 2000 specific to the Bond Graphs
made it possible to validate and have the results given by the
technical specifications. We introduce the analysis of the problem
involved in the faults localization and identification in the complex
industrial processes. We propose a method of fault detection applied
to the diagnosis and to determine the gravity of a detected fault. We
show the possibilities of application of the new diagnosis approaches
to the complex system control. The industrial systems became
increasingly complex with the faults diagnosis procedures in the
physical systems prove to become very complex as soon as the
systems considered are not elementary any more. Indeed, in front of
this complexity, we chose to make recourse to Fault Detection and
Isolation method (FDI) by the analysis of the problem of its control
and to conceive a reliable system of diagnosis making it possible to
apprehend the complex dynamic systems spatially distributed applied
to the standard pressurized water nuclear reactor.
Abstract: With China's urbanization continuing to accelerate, a amount of rural people flood into China's cities in recent years, and the issue of agriculture, rural areas and farmers is getting more and more serious. In 2005, the Chinese government put forward a plan for “the construction of new rural village", in order to coordinate the development of both urban and rural areas. The planning method of rural region differs sharply from that of urban areas, as same as village social structure and habits of farmer-s life, so the studies which can consider the special needs of village construction in China are absolutely essential. This paper expresses explore current situation and problems existing in the construction of China-s new rural village, such as bigger gap between urban and rural areas, excessive new construction projects, extinct traditional village style and so on. It tries to analyze the deep reason of the present situation of the village from law system, industrial structure, financial sources and planning method. Then it also provides a guide for developing policies and procedures promoting the development of china-s rural areas.