Abstract: This paper presents a synthetic jet air blower actuated
by PZT for air blowing for air-breathing micro PEM fuel cell. The
several factors to affect the performance of air-breathing PEM fuel cell
such as air flow rate, opening ratio and cathode open type in the
cathode side were studied. Especially, an air flow rate is critical
condition to improve its performance. In this paper, we developed a
synthetic jet air blower to supply a high stoichiometric air flow. The
synthetic jet mechanism is a zero mass flux device that converts
electrical energy into the momentum. The synthetic jet actuation is
usually generated by a traditional PZT actuator, which consists of a
small cylindrical cavity, in/outlet channel and PZT diaphragms. The
flow rate of the fabricated synthetic jet air blower was 400cc/min at
550Hz and its power consumption was very low under 0.3W. The
proposed air-breathing PEM fuel cell which installed synthetic jet air
blower was higher performance and stability during continuous
operation than the air-breathing fuel cell without auxiliary device to
supply the air. The results showed that the maximum power density
was 188mW/cm2 at 400mA/cm2. This maximum power density and
durability were improved more than 40% and 20%, respectively.
Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.
Abstract: The tubes in an Ammonia primary reformer furnace
operate close to the limits of materials technology in terms of the
stress induced as a result of very high temperatures, combined with
large differential pressures across the tube wall. Operation at tube
wall temperatures significantly above design can result in a rapid
increase in the number of tube failures, since tube life is very
sensitive to the absolute operating temperature of the tube. Clearly it
is important to measure tube wall temperatures accurately in order to
prevent premature tube failure by overheating.. In the present study,
the catalyst tubes in an Ammonia primary reformer has been modeled
taking into consideration heat, mass and momentum transfer as well
as reformer characteristics.. The investigations concern the effects of
tube characteristics and superficial tube wall temperatures on of the
percentage of heat flux, unconverted methane and production of
Hydrogen for various values of steam to carbon ratios. The results
show the impact of catalyst tubes length and diameters on the
performance of operating parameters in ammonia primary reformers.
Abstract: This paper describes about dynamic reconfiguration to
miniaturize arithmetic circuits in general-purpose processor. Dynamic
reconfiguration is a technique to realize required functions by
changing hardware construction during operation. The proposed
arithmetic circuit performs floating-point arithmetic which is
frequently used in science and technology. The data format is
floating-point based on IEEE754. The proposed circuit is designed
using VHDL, and verified the correct operation by simulations and
experiments.
Abstract: Diagnostic and detection of the arterial stiffness is
very important; which gives indication of the associated increased risk of cardiovascular diseases. To make a cheap and easy method for general screening technique to avoid the future cardiovascular
complexes , due to the rising of the arterial stiffness ; a proposed algorithm depending on photoplethysmogram to be used. The
photoplethysmograph signals would be processed in MATLAB. The
signal will be filtered, baseline wandering removed, peaks and
valleys detected and normalization of the signals should be achieved
.The area under the catacrotic phase of the photoplethysmogram
pulse curve is calculated using trapezoidal algorithm ; then will used
in cooperation with other parameters such as age, height, blood
pressure in neural network for arterial stiffness detection. The Neural
network were implemented with sensitivity of 80%, accuracy 85%
and specificity of 90% were got from the patients data. It is
concluded that neural network can detect the arterial STIFFNESS
depending on risk factor parameters.
Abstract: This paper presents Qmulus- a Cloud Based GPS
Model. Qmulus is designed to compute the best possible route which
would lead the driver to the specified destination in the shortest time
while taking into account real-time constraints. Intelligence
incorporated to Qmulus-s design makes it capable of generating and
assigning priorities to a list of optimal routes through customizable
dynamic updates. The goal of this design is to minimize travel and
cost overheads, maintain reliability and consistency, and implement
scalability and flexibility. The model proposed focuses on
reducing the bridge between a Client Application and a Cloud
service so as to render seamless operations. Qmulus-s system
model is closely integrated and its concept has the potential to be
extended into several other integrated applications making it capable
of adapting to different media and resources.
Abstract: Cooperative visual modeling is more and more
necessary in our complicated world. A collaborative environment
which supports interactive operation and communication is required
to increase work efficiency. We present a collaborative visual
modeling framework which collaborative platform could be built on.
On this platform, cooperation and communication is available for
designers from different regions. This framework, which is different
from other collaborative frameworks, contains a uniform message
format, a message handling mechanism and other functions such as
message pretreatment and Role-Communication-Token Access
Control (RCTAC). We also show our implementation of this
framework called Orchestra Designer, which support BPLE
workflow modeling cooperatively online.
Abstract: The Implementation of the Union law faces major
challenges today. If for a long period of time, the Community and the
Union have persevered in their legislative vocation, now one can
notice that this large legislative quantity has complicated the task of
knowledge and of application the European standards. Under these
circumstances, it became necessary, in order to give effectiveness to
the European legislation, the development of some operational
application criteria and the generation of some new implementation
tools. The correct application of the European Union legislation by
the national public administrations was considered by the European
Commission as being crucial for further integration and proper
functioning of the internal market. Among the initiatives launched in
the past years to promote the exchange of good administrative
practices in the correct application of European Union legislation,
SOLVIT net has proved to be one of the most effective.
Abstract: Does education matter to the quality of our life? The results of extensive studies offer an affirmative answer to this question: high education levels are positively associated with higher income, with more highly qualified professions, with lower risk of unemployment, with better physical health and also, it is said, with more happiness. However, exploring these relationships is far from straightforward. Aside from educational credentials, what properties distinguish functionally literate individuals? How can their personal level of satisfaction be measured? What are the social mechanisms whereby education affects well-being?Using a literacy index and several measures for well-being developed by secondary analysis of the Adult Literacy and Life Skills Survey database, this investigation examined the relationship between literacy skills and subjective wellbeing in several OECD (Organisation for Economic Co-operation and Development) countries. Special attention was been addressed to Italy, and in particular to two regions representing territorial differences in this country: Piedmont and Campania.
Abstract: The purpose of the paper is to develop an informationcontrol environment for overall management and self-reconfiguration of the reconfigurable multifunctional machine tool for machining both rotation and prismatic parts and high concentration of different technological operations - turning, milling, drilling, grinding, etc. For the realization of this purpose on the basis of defined sub-processes for the implementation of the technological process, architecture of the information-search system for machine control is suggested. By using the object-oriented method, a structure and organization of the search system based on agents and manager with central control are developed. Thus conditions for identification of available information in DBs, self-reconfiguration of technological system and entire control of the reconfigurable multifunctional machine tool are created.
Abstract: In this paper, a data mining model to SMEs for detecting financial and operational risk indicators by data mining is presenting. The identification of the risk factors by clarifying the relationship between the variables defines the discovery of knowledge from the financial and operational variables. Automatic and estimation oriented information discovery process coincides the definition of data mining. During the formation of model; an easy to understand, easy to interpret and easy to apply utilitarian model that is far from the requirement of theoretical background is targeted by the discovery of the implicit relationships between the data and the identification of effect level of every factor. In addition, this paper is based on a project which was funded by The Scientific and Technological Research Council of Turkey (TUBITAK).
Abstract: For many industrial applications plate heat
exchangers are demonstrating a large superiority over the
other types of heat exchangers. The efficiency of such a
device depends on numerous factors the effect of which needs
to be analysed and accurately evaluated.
In this paper we present a theoretical analysis of a cocurrent
plate heat exchanger and the results of its numerical
simulation.
Knowing the hot and the cold fluid streams inlet temperatures,
the respective heat capacities mCp
and the value of the
overall heat transfer coefficient, a 1-D mathematical model
based on the steady flow energy balance for a differential
length of the device is developed resulting in a set of N first
order differential equations with boundary conditions where N
is the number of channels.For specific heat exchanger
geometry and operational parameters, the problem is
numerically solved using the shooting method.
The simulation allows the prediction of the temperature
map in the heat exchanger and hence, the evaluation of its
performances. A parametric analysis is performed to evaluate
the influence of the R-parameter on the e-NTU values. For
practical purposes effectiveness-NTU graphs are elaborated
for specific heat exchanger geometry and different operating
conditions.
Abstract: Middle-gate is located in Hasankeyf, Batman dating
back to 1800 BC and is one of the important historical structures in
Turkey. The ancient structure has suffered major structural cracks
due to aging as well as lateral pressure of a cracked rock which is
predicted to be about 100 tons. The existing support system was
found to be inadequate to support the load especially after a recent
rock fall in the close vicinity. Concerns were increased since the
existing support system that is integral with a damaged and cracked
gate wall needed to be replaced by a new support system. The
replacement process must be carefully monitored by crackmeters and
control mechanisms should be integrated to prevent cracks to expand
while the same crack width needs to be maintained after the
operation. The control system and actions taken during the
intervention are explained in this paper.
Abstract: While the explosive increase in information published
on the Web, researchers have to filter information when searching for
conference related information. To make it easier for users to search
related information, this paper uses Topic Maps and social information
to implement ontology since ontology can provide the formalisms and
knowledge structuring for comprehensive and transportable machine
understanding that digital information requires. Besides enhancing
information in Topic Maps, this paper proposes a method of
constructing research Topic Maps considering social information.
First, extract conference data from the web. Then extract conference
topics and the relationships between them through the proposed
method. Finally visualize it for users to search and browse. This paper
uses ontology, containing abundant of knowledge hierarchy structure,
to facilitate researchers getting useful search results. However, most
previous ontology construction methods didn-t take “people" into
account. So this paper also analyzes the social information which helps
researchers find the possibilities of cooperation/combination as well as
associations between research topics, and tries to offer better results.
Abstract: Paper deals with the topic of questions as important
components of information behavior in the school. By analyzing the
Corpus Schola2010, the state of contemporary education in terms of
questioning is proven unsatisfactory: 80% of the questions are asked
by teachers; most of teacher-s questions are asked at the beginning of
the first grade, than their number decreases and is settling down on
80±10 questions per lesson. The average number of questions within
one lesson per one pupil is generally less than one whole question.
The highest values are achieved in the first, sixth, eighth and tenth
grade,, i.e. in the transition years in which pupils are moving into
higher levels of education and every following year it declines. We
can state Czech school do not support questioning and question skill
of their pupils, thereby typical Czech schools are neglecting the
development of thinking, reasoning and cooperation of their pupils.
Abstract: Machining is an important manufacturing process used to produce a wide variety of metallic parts. Among various machining processes, turning is one of the most important one which is employed to shape cylindrical parts. In turning, the quality of finished product is measured in terms of surface roughness. In turn, surface quality is determined by machining parameters and tool geometry specifications. The main objective of this study is to simultaneously model and optimize machining parameters and tool geometry in order to improve the surface roughness for AISI1045 steel. Several levels of machining parameters and tool geometry specifications are considered as input parameters. The surface roughness is selected as process output measure of performance. A Taguchi approach is employed to gather experimental data. Then, based on signal-to-noise (S/N) ratio, the best sets of cutting parameters and tool geometry specifications have been determined. Using these parameters values, the surface roughness of AISI1045 steel parts may be minimized. Experimental results are provided to illustrate the effectiveness of the proposed approach.
Abstract: A numerical method for solving nonlinear Fredholm integral equations of second kind is proposed. The Fredholm type equations which have many applications in mathematical physics are then considered. The method is based on hybrid function approximations. The properties of hybrid of block-pulse functions and Chebyshev polynomials are presented and are utilized to reduce the computation of nonlinear Fredholm integral equations to a system of nonlinear. Some numerical examples are selected to illustrate the effectiveness and simplicity of the method.
Abstract: The increasing development of wireless networks and
the widespread popularity of handheld devices such as Personal
Digital Assistants (PDAs), mobile phones and wireless tablets
represents an incredible opportunity to enable mobile devices as a
universal payment method, involving daily financial transactions.
Unfortunately, some issues hampering the widespread acceptance of
mobile payment such as accountability properties, privacy protection,
limitation of wireless network and mobile device. Recently, many
public-key cryptography based mobile payment protocol have been
proposed. However, limited capabilities of mobile devices and
wireless networks make these protocols are unsuitable for mobile
network. Moreover, these protocols were designed to preserve
traditional flow of payment data, which is vulnerable to attack and
increase the user-s risk. In this paper, we propose a private mobile
payment protocol which based on client centric model and by
employing symmetric key operations. The proposed mobile payment
protocol not only minimizes the computational operations and
communication passes between the engaging parties, but also
achieves a completely privacy protection for the payer. The future
work will concentrate on improving the verification solution to
support mobile user authentication and authorization for mobile
payment transactions.
Abstract: A first intermediate roll of Sendzirmir mills was failure
by surface spalling during operation. After analyzing by visual, stereo
microscope, optical microscope, scanning electron microscope,
glow-discharged spectrometer and hardness test, respectively, the
results show that some voids and cracks existed on the contact surface
as well as subsurface. Further examination verified inadequate
hardness and inclusions were responsible for the failure of surface
spalling.
Abstract: Due to the limited energy resources, energy efficient operation of sensor node is a key issue in wireless sensor networks. Clustering is an effective method to prolong the lifetime of energy constrained wireless sensor network. However, clustering in wireless sensor network faces several challenges such as selection of an optimal group of sensor nodes as cluster, optimum selection of cluster head, energy balanced optimal strategy for rotating the role of cluster head in a cluster, maintaining intra and inter cluster connectivity and optimal data routing in the network. In this paper, we propose a protocol supporting an energy efficient clustering, cluster head selection/rotation and data routing method to prolong the lifetime of sensor network. Simulation results demonstrate that the proposed protocol prolongs network lifetime due to the use of efficient clustering, cluster head selection/rotation and data routing.