Abstract: This research investigates the effects of the opening
shape and location on the structural behavior of reinforced concrete
deep beam with openings, while keeping the opening size unchanged.
The software ANSYS 12.1 is used to handle the nonlinear finite
element analysis. The ultimate strength of reinforced concrete deep
beam with opening obtained by ANSYS 12.1 shows fair agreement
with the experimental results, with a difference of no more than 20%. The present work concludes that the opening location has much more effect on the structural strength than the opening shape. It was
concluded that placing the openings near the upper corners of the
deep beam may double the strength, and the use of a rectangular
narrow opening, with the long sides in the horizontal direction, can save up to 40% of structural strength of the deep beam.
Abstract: Irradiation is considered one of the most efficient technological processes for the reduction of microorganisms in food. It can be used to improve the safety of food products, and to extend their shelf lives. The aim of this study was to evaluate the effects of gamma irradiation for improvement of saffron shelf life. Samples were treated with 0 (none irradiated), 1.0, 2.0, 3.0 and 4.0 kGy of gamma irradiation and held for 2 months. The control and irradiated samples were underwent microbial analysis, chemical characteristics and sensory evaluation at 30 days intervals. Microbial analysis indicated that irradiation had a significant effect (P < 0.05) on the reduction of microbial loads. There was no significant difference in sensory quality and chemical characteristics during storage in saffron.
Abstract: An attempt has been made to determine the strength
and impact properties of Cr-Mo steel weld and base materials by
varying the current during manual metal arc welding. Toughness over
a temperature range from -32 to 100°C of base, heat affected zone
(HAZ) and weld zones at three current settings are made. It is
observed that the deterioration in notch toughness at any zone with
the temperature decreases. The values of notch toughness for all
zones at -32°C are almost same for any current settings. The values
of notch toughness at HAZ area are higher than that of weld area due
to the coarsening of ferrite grain of HAZ occurs with higher heat
input. From microhardness and microstructure result, it can be
concluded that large inclusion content in weld deposit is the cause of
lower notch toughness value.
Abstract: Air quality studies were carried out in the towns of
Putrajaya, Petaling Jaya and Nilai in the Malaysian Peninsular. In this
study, the variations of Ozone (O3) concentrations over a four year
period (2008-2011) were investigated using data obtained from the
Malaysian Department of the Environment (DOE). This study aims to
identify and describe the daily and monthly variations of O3
concentrations at the monitoring sites mentioned. The SPPS program
(Statistical Package for the Social Science) was used to analyze this
data in order to obtain the variations of O3 and also to clarify the
relationship between the stations. The findings of the study revealed
that the highest concentration of O3 occurred during the midday and
afternoon (between 13:00-15:00 hrs). The comparison between
stations also showed that highest O3 concentrations were recorded in
Putrajaya. The comparisons of average and maximum concentrations
of O3 for the three stations showed that the strongest significant
correlation was recorded in the Petaling Jaya station with the value
R2= 0.667. Results from this study indicate that in the urban areas of
Peninsular Malaysia, the concentration of O3 depends on the
concentration of NOx. Furthermore, HYSPLIT back trajectories
(-72h) indicated that air-mass transport patterns can also influence the
O3 concentration in the areas studied.
Abstract: In order to investigate water deficit stress on 24 of
soybean (Glycine Max. L) cultivars and lines in temperate climate, an
experiment was conducted in Iran Seed and Plant Improvement
Institute. Stress levels were irrigation after evaporation of 50, 100,
150 mm water from pan, class A. Randomized Completely Block
Design was arranged for each stress levels. Some traits such as, node
number, plant height, pod number per area, grain number per pod,
grain number per area, 1000 grains weight, grain yield and harvest
index were measured. Results showed that water deficit stress had
significant effect on node number, plant height, pod number per area,
grain number per pod, grain number per area, 1000 grains weight and
harvest index. Also all of agronomic traits except harvest index
influenced significantly by cultivars and lines. The least and most
grain yield was belonged to Ronak X Williams and M41 x Clark
respectively.
Abstract: A wireless sensor network with a large number of tiny sensor nodes can be used as an effective tool for gathering data in various situations. One of the major issues in wireless sensor networks is developing an energy-efficient routing protocol which has a significant impact on the overall lifetime of the sensor network. In this paper, we propose a novel hierarchical with static clustering routing protocol called Energy-Efficient Protocol with Static Clustering (EEPSC). EEPSC, partitions the network into static clusters, eliminates the overhead of dynamic clustering and utilizes temporary-cluster-heads to distribute the energy load among high-power sensor nodes; thus extends network lifetime. We have conducted simulation-based evaluations to compare the performance of EEPSC against Low-Energy Adaptive Clustering Hierarchy (LEACH). Our experiment results show that EEPSC outperforms LEACH in terms of network lifetime and power consumption minimization.
Abstract: Design and land use are closely linked to the
energy efficiency levels for an urban area. The current city
planning practice does not involve an effective land useenergy
evaluation in its 'blueprint' urban plans. The study
proposed an appraisal method that can be embedded in GIS
programs using five planning criteria as how far a planner can
give away from the planning principles (criteria) for the most
energy output s/he can obtain. The case of Balcova, a district
in the Izmir Metropolitan area, is used conformingly for
evaluating the proposed master plan and the geothermal
energy (heating only) use for the concern district.
If the land use design were proposed accordingly at-most
energy efficiency (a 30% obtained), mainly increasing the
density around the geothermal wells and also proposing more
mixed use zones, we could have 17% distortion (infidelity to
the main planning principles) from the original plan. The
proposed method can be an effective tool for planners as
simulation media, of which calculations can be made by GIS
ready tools, to evaluate efficiency levels for different plan
proposals, letting to know how much energy saving causes
how much deviation from the other planning ideals. Lower
energy uses can be possible for different land use proposals
for various policy trials.
Abstract: This paper presents a simple and sensitive kinetic
spectrophotometric method for the determination of ramipril in
commercial dosage forms. The method is based on the reaction of the
drug with 1-chloro-2,4-dinitrobenzene (CDNB) in dimethylsulfoxide
(DMSO) at 100 ± 1ºC. The reaction is followed
spectrophotometrically by measuring the rate of change of the
absorbance at 420 nm. Fixed-time (ΔA) and equilibrium methods are
adopted for constructing the calibration curves. Both the calibration
curves were found to be linear over the concentration ranges 20 - 220
μg/ml. The regression analysis of calibration data yielded the linear
equations: Δ A = 6.30 × 10-4 + 1.54 × 10-3 C and A = 3.62 × 10-4 +
6.35 × 10-3 C for fixed time (Δ A) and equilibrium methods,
respectively. The limits of detection (LOD) for fixed time and
equilibrium methods are 1.47 and 1.05 μg/ml, respectively. The
method has been successfully applied to the determination of ramipril
in commercial dosage forms. Statistical comparison of the results
shows that there is no significant difference between the proposed
methods and Abdellatef-s spectrophotometric method.
Abstract: Tungsten trioxide has been prepared by using P-PTA
as a precursor on alumina substrates by spin coating method.
Palladium introduced on WO3 film via electrolysis deposition by
using palladium chloride as catalytic precursor. The catalytic
precursor was introduced on the series of films with different
morphologies. X-ray diffractometry (XRD), Scanning electron
microscopy (SEM) and XPS were applied to analyze structure and
morphology of the fabricated thin films. Then we measured variation
of samples- electrical conductivity of pure and Pd added films in air
and diluted hydrogen. Addition of Pd resulted in a remarkable
improvement of the hydrogen sensing properties of WO3 by detection
of Hydrogen below 1% at room temperature. Also variation of the
electrical conductivity in the presence of diluted hydrogen revealed
that response of samples depends rather strongly on the palladium
configuration on the surface.
Abstract: Wind turbines with double output induction
generators can operate at variable speed permitting conversion
efficiency maximization over a wide range of wind velocities. This
paper presents the performance analysis of a wind driven double
output induction generator (DOIG) operating at varying shafts speed.
A periodic transient state analysis of DOIG equipped with two
converters is carried out using a hybrid induction machine model.
This paper simulates the harmonic content of waveforms in various
points of drive at different speeds, based on the hybrid model
(dqabc). Then the sinusoidal and trapezoidal pulse-width–modulation
control techniques are used in order to improve the power factor of
the machine and to weaken the injected low order harmonics to the
supply. Based on the frequency spectrum, total harmonics distortion,
distortion factor and power factor. Finally advantages of sinusoidal
and trapezoidal pulse width modulation techniques are compared.
Abstract: Semiconductor materials with coatings have a wide range of applications in MEMS and NEMS. This work uses transfermatrix method for calculating the radiative properties. Dopped silicon is used and the coherent formulation is applied. The Drude model for the optical constants of doped silicon is employed. Results showed that for the visible wavelengths, more emittance occurs in greater concentrations and the reflectance decreases as the concentration increases. In these wavelengths, transmittance is negligible. Donars and acceptors act similar in visible wavelengths. The effect of wave interference can be understood by plotting the spectral properties such as reflectance or transmittance of a thin dielectric film versus the film thickness and analyzing the oscillations of properties due to constructive and destructive interferences. But this effect has not been shown at visible wavelengths. At room temperature, the scattering process is dominated by lattice scattering for lightly doped silicon, and the impurity scattering becomes important for heavily doped silicon when the dopant concentration exceeds1018cm-3 .
Abstract: Environmental aspects plays a central role in environmental management system (EMS) because it is the basis for the identification of an organization-s environmental targets. The
existing methods for the assessment of environmental aspects are grouped into three categories: risk assessment-based (RA-based),
LCA-based and criterion-based methods. To combine the benefits of
these three categories of research, this study proposes an integrated framework, combining RA-, LCA- and criterion-based methods. The
integrated framework incorporates LCA techniques for the identification of the causal linkage for aspect, pathway, receptor and
impact, uses fuzzy logic to assess aspects, considers fuzzy conditions,
in likelihood assessment, and employs a new multi-criteria decision analysis method - multi-criteria and multi-connection comprehensive
assessment (MMCA) - to estimate significant aspects in EMS. The proposed model is verified, using a real case study and the results show
that this method successfully prioritizes the environmental aspects.
Abstract: Weather systems use enormously complex
combinations of numerical tools for study and forecasting.
Unfortunately, due to phenomena in the world climate, such
as the greenhouse effect, classical models may become
insufficient mostly because they lack adaptation. Therefore,
the weather forecast problem is matched for heuristic
approaches, such as Evolutionary Algorithms.
Experimentation with heuristic methods like Particle Swarm
Optimization (PSO) algorithm can lead to the development of
new insights or promising models that can be fine tuned with
more focused techniques. This paper describes a PSO
approach for analysis and prediction of data and provides
experimental results of the aforementioned method on realworld
meteorological time series.
Abstract: A multivariable discontinuous feedback linearization approach is proposed to position control of an electrically driven fast robot manipulator. A desired performance is achieved by selecting a useful controller and suitable sampling rate and considering saturation for actuators. There is a high flexibility to apply the proposed control approach on different electrically driven manipulators. The control approach can guarantee the stability and satisfactory tracking performance. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a desired performance for control system under technical specifications.
Abstract: Whereas in the third generation nuclear reactors,
dimensions of core and also the kind of coolant and enrichment
percent of fuel have significantly changed than the second
generation, therefore in this article the aim is based on a
comparative investigation between two same power reactors of
second and third generations, that the neutronic parameters of both
reactors such as: K∞, Keff and its details and thermal hydraulic
parameters such as: power density, specific power, volumetric heat
rate, released power per fuel volume unit, volume and mass of clad
and fuel (consisting fissile and fertile fuels), be calculated and
compared together. By this comparing the efficiency and
modification of third generation nuclear reactors than second
generation which have same power can be distinguished.
In order to calculate the cited parameters, some information
such as: core dimensions, the pitch of lattice, the fuel matter, the
percent of enrichment and the kind of coolant are used. For
calculating the neutronic parameters, a neutronic program entitled:
SIXFAC and also related formulas have been used. Meantime for
calculating the thermal hydraulic and other parameters, analytical
method and related formulas have been applied.
Abstract: In this paper we present a general formalism for the
establishment of the family of selective regressor affine projection
algorithms (SR-APA). The SR-APA, the SR regularized APA (SR-RAPA),
the SR partial rank algorithm (SR-PRA), the SR binormalized
data reusing least mean squares (SR-BNDR-LMS), and the SR normalized
LMS with orthogonal correction factors (SR-NLMS-OCF)
algorithms are established by this general formalism. We demonstrate
the performance of the presented algorithms through simulations in
acoustic echo cancellation scenario.
Abstract: This paper reviews designs of the built environment
from a sustainability perspective, emphasizing their importance in
achieving ecological and sustainable economic objectives. The built
environment has traditionally resulted in loss of biodiversity,
extinction of some species, climate change, excessive water use, land
degradation, space depletion, waste accumulation, energy
consumption and environmental pollution. Materials used like
plastics, metals, bricks, concrete, cement, natural aggregates, glass
and plaster have wreaked havoc on the earth´s resources, since they
have high levels of embodied energy hence not sustainable.
Additional resources are consumed during use and disposal phases.
Proposed designs for sustainability solutions include: ecological
sanitation and eco-efficiency systems that ensure social, economic,
environmental and technical sustainability. Renewable materials and
energy systems, passive cooling and heating systems and material
and energy reduction, reuse and recycling can improve the sector.
These ideas are intended to inform the field of ecological design of
the built environment.
Abstract: As global industry developed rapidly, the energy
demand also rises simultaneously. In the production process, there’s a
lot of energy consumed in the process. Formally, the energy used in
generating the heat in the production process. In the total energy
consumption, 40% of the heat was used in process heat, mechanical
work, chemical energy and electricity. The remaining 50% were
released into the environment. It will cause energy waste and
environment pollution. There are many ways for recovering the waste
heat in factory. Organic Rankine Cycle (ORC) system can produce
electricity and reduce energy costs by recovering the waste of low
temperature heat in the factory. In addition, ORC is the technology
with the highest power generating efficiency in low-temperature heat
recycling. However, most of factories executives are still hesitated
because of the high implementation cost of the ORC system, even a lot
of heat are wasted. Therefore, this study constructs a nonlinear
mathematical model of waste heat recovery equipment configuration
to maximize profits. A particle swarm optimization algorithm is
developed to generate the optimal facility installation plan for the ORC
system.
Abstract: In this work, we analyze the deformation of surface
waves in shallow flows conditions, propagating in a channel of
slowly varying cross-section. Based on a singular perturbation
technique, the main purpose is to predict the motion of waves by
using a dimensionless formulation of the governing equations,
considering that the longitudinal variation of the transversal section
obey a power-law distribution. We show that the spatial distribution
of the waves in the varying cross-section is a function of a kinematic
parameter,κ , and two geometrical parameters εh
and w ε . The above
spatial behavior of the surface elevation is modeled by an ordinary
differential equation. The use of single formulas to model the varying
cross sections or transitions considered in this work can be a useful
approximation to natural or artificial geometrical configurations.
Abstract: Deoxygenation of beef fat for the production of hydrogenated biodiesel is investigated in a high pressure continuous flow fixed bed reactor over palladium-supported mesoporous titania catalyst synthesized via a combined single-step sol-gel process with surfactant-assisted templating method (SATM). The catalyst possessed a mesoporous charactheristic with high surface area and narrow pore size distribution. The main products of all Pd/TiO2 catalysts are n-heptadecane (n-C17) and n-pentadecane (n-C15) resulting from decarbonylation reaction. Pd/TiO2 catalyst synthesized via a combined single-step sol-gel process with SATM (SSSG) gave higher activity and selectivity to the desired products when compared to IWI/SG-TiO2 and IWI/P25-TiO2, respectively. SSSG catalyst gave the average conversion up to 80-90 % and 80 % for the selectivity in diesel range hydrocarbons. This result may cause by the higher surface area and the ability in dispersion of palladium ion in mesoporous of TiO2 during sol-gel process.