Abstract: This study investigated a strategy of blending lead-laden sludge and Al-rich precursors to reduce the release of metals from the stabilized products. Using PbO as the simulated lead-laden sludge to sinter with γ-Al2O3 by Pb:Al molar ratios of 1:2 and 1:12, PbAl2O4 and PbAl12O19 were formed as final products during the sintering process, respectively. By firing the PbO + γ-Al2O3 mixtures with different Pb/Al molar ratios at 600 to 1000 °C, the lead transformation was determined through X-ray diffraction (XRD) data. In Pb/Al molar ratio of 1/2 system, the formation of PbAl2O4 is initiated at 700 °C, but an effective formation was observed above 750 °C. An intermediate phase, Pb9Al8O21, was detected in the temperature range of 800-900 °C. However, different incorporation behavior for sintering PbO with Al-rich precursors at a Pb/Al molar ratio of 1/12 was observed during the formation of PbAl12O19 in this system. In the sintering process, both temperature and time effect on the formation of PbAl2O4 and PbAl12O19 phases were estimated. Finally, a prolonged leaching test modified from the U.S. Environmental Protection Agency-s toxicity characteristic leaching procedure (TCLP) was used to evaluate the durability of PbO, Pb9Al8O21, PbAl2O4 and PbAl12O19 phases. Comparison for the leaching results of the four phases demonstrated the higher intrinsic resistance of PbAl12O19 against acid attack.
Abstract: In this research, CaO-ZnO catalysts (with various
Ca:Zn atomic ratios of 1:5, 1:3, 1:1, and 3:1) prepared by incipientwetness
impregnation (IWI) and co-precipitation (CP) methods were
used as a catalyst in the transesterification of palm oil with methanol
for biodiesel production. The catalysts were characterized by several
techniques, including BET method, CO2-TPD, and Hemmett
Indicator. The effects of precursor concentration, and calcination
temperature on the catalytic performance were studied under reaction
conditions of a 15:1 methanol to oil molar ratio, 6 wt% catalyst,
reaction temperature of 60°C, and reaction time of 8 h. At Ca:Zn
atomic ratio of 1:3 gave the highest FAME value owing to a basic
properties and surface area of the prepared catalyst.
Abstract: This paper reports the results of an experimental work
conducted to investigate the effect of curing conditions on the
compressive strength of self-compacting geopolymer concrete
prepared by using fly ash as base material and combination of sodium
hydroxide and sodium silicate as alkaline activator. The experiments
were conducted by varying the curing time and curing temperature in
the range of 24-96 hours and 60-90°C respectively. The essential
workability properties of freshly prepared Self-compacting
Geopolymer concrete such as filling ability, passing ability and
segregation resistance were evaluated by using Slump flow,
V-funnel, L-box and J-ring test methods. The fundamental
requirements of high flowability and resistance to segregation as
specified by guidelines on Self-compacting Concrete by EFNARC
were satisfied. Test results indicate that longer curing time and curing
the concrete specimens at higher temperatures result in higher
compressive strength. There was increase in compressive strength
with the increase in curing time; however increase in compressive
strength after 48 hours was not significant. Concrete specimens cured
at 70°C produced the highest compressive strength as compared to
specimens cured at 60°C, 80°C and 90°C.
Abstract: Not with standing the importance of foreign highly
skilled professionals for host economies, there is a paucity of
research studies investigating the role of the corporate social context
during the integration process. This research aims to address this
paucity by exploring the role of social capital in the integration of
foreign health professionals. It does so by using a qualitative research
approach. In this pilot study the hospital sector forms this study-s
sample and interviews were conducted with HR managers, foreign
health professionals and external HR consultants. It was found that
most of the participating hospitals had not established specific HR
practices and had only partly linked the development of
organisational social capital with a successful integration process.
This research contributes, for example, to the HR literature on the
integration of self-initiated expatriates by analysing the role of HRM
in generating organisational social capital needed for a successful
integration process.
Abstract: Ensemble learning algorithms such as AdaBoost and
Bagging have been in active research and shown improvements in
classification results for several benchmarking data sets with mainly
decision trees as their base classifiers. In this paper we experiment to
apply these Meta learning techniques with classifiers such as random
forests, neural networks and support vector machines. The data sets
are from MAGIC, a Cherenkov telescope experiment. The task is to
classify gamma signals from overwhelmingly hadron and muon
signals representing a rare class classification problem. We compare
the individual classifiers with their ensemble counterparts and
discuss the results. WEKA a wonderful tool for machine learning has
been used for making the experiments.
Abstract: The aim of the research is to understand whether the accuracy of customer detection of employee emotional labor strategy would influence the overall service satisfaction. From path analysis, it was found that employee-s positive emotions positively influenced service quality. Service quality in turn influenced Customer detection of employee emotional deep action strategy and Customer detection of employee emotional surface action strategy. Lastly, Customer detection of employee emotional deep action strategy and Customer detection of employee emotional surface action strategy positively influenced service satisfaction. Based on the analysis results, suggestions are proposed to provide reference for human resource management and use in relative fields.
Abstract: The hot deformation behavior of high strength low
alloy (HSLA) steels with different chemical compositions under hot
working conditions in the temperature range of 900 to 1100℃ and
strain rate range from 0.1 to 10 s-1 has been studied by performing a
series of hot compression tests. The dynamic materials model has been
employed for developing the processing maps, which show variation
of the efficiency of power dissipation with temperature and strain rate.
Also the Kumar-s model has been used for developing the instability
map, which shows variation of the instability for plastic deformation
with temperature and strain rate. The efficiency of power dissipation
increased with decreasing strain rate and increasing temperature in the
steel with higher Cr and Ti content. High efficiency of power
dissipation over 20 % was obtained at a finite strain level of 0.1 under
the conditions of strain rate lower than 1 s-1 and temperature higher
than 1050 ℃ . Plastic instability was expected in the regime of
temperatures lower than 1000 ℃ and strain rate lower than 0.3 s-1. Steel
with lower Cr and Ti contents showed high efficiency of power
dissipation at higher strain rate and lower temperature conditions.
Abstract: One of the most important requirements for the
operation and planning activities of an electrical utility is the
prediction of load for the next hour to several days out, known as
short term load forecasting. This paper presents the development of
an artificial neural network based short-term load forecasting model.
The model can forecast daily load profiles with a load time of one
day for next 24 hours. In this method can divide days of year with
using average temperature. Groups make according linearity rate of
curve. Ultimate forecast for each group obtain with considering
weekday and weekend. This paper investigates effects of temperature
and humidity on consuming curve. For forecasting load curve of
holidays at first forecast pick and valley and then the neural network
forecast is re-shaped with the new data. The ANN-based load models
are trained using hourly historical. Load data and daily historical
max/min temperature and humidity data. The results of testing the
system on data from Yazd utility are reported.
Abstract: The halophilic proteinase showed a maximal activity
at 50°C and pH 9~10, in 20% NaCl and was highly stabilized by
NaCl. It was able to hydrolyse natural actomyosin (NAM), collagen
and anchovy protein. For NAM hydrolysis, the myosin heavy chain
was completely digested by halophilic proteinase as evidenced by the
lowest band intensity remaining, but partially hydrolysed actin. The
SR5-3 proteinase was also capable hydrolyzing two major
components of collagen, β- and α-compounds, effectively. The
degree of hydrolysis (DH) of the halophilic proteinase and
commercial proteinases (Novozyme, Neutrase, chymotrypsin and
Flavourzyme) on the anchovy protein, were compared, and it was
found that the proteinase showed a greater degree of hydrolysis
towards anchovy protein than that from commercial proteinases. DH
of halophilic proteinase was sharply enhanced according to the
increase in the concentration of enzyme from 0.035 U to 0.105 U.
The results warranting that the acceleration of the production of fish
sauce with higher quality, may be achieved by adding of the
halophilic proteinase from this bacterium.
Abstract: The dental composites are preferably used as filling
materials due to their esthetic appearances. Nevertheless one of the
major problems, during the application of the dental composites, is
shape change named as “polymerisation shrinkage" affecting clinical
success of the dental restoration while photo-polymerisation.
Polymerisation shrinkage of composites arises basically from the
formation of a polymer due to the monomer transformation which
composes of an organic matrix phase. It was sought, throughout this
study, to detect and evaluate the structural polymerisation shrinkage
of prepared dental composites in order to optimize the effects of
various fillers included in hydroxyapatite (HA)-reinforced dental
composites and hence to find a means to modify the properties of
these dental composites prepared with defined parameters. As a
result, the shrinkage values of the experimental dental composites
were decreased by increasing the filler content of composites and the
composition of different fillers used had effect on the shrinkage of
the prepared composite systems.
Abstract: As seen in literature, about 70% of the improvement initiatives fail, and a significant number do not even get started. This paper analyses the problem of failing initiatives on Software Process Improvement (SPI), and proposes good practices supported by motivational tools that can help minimizing failures. It elaborates on the hypothesis that human factors are poorly addressed by deployers, especially because implementation guides usually emphasize only technical factors. This research was conducted with SPI deployers and analyses 32 SPI initiatives. The results indicate that although human factors are not commonly highlighted in guidelines, the successful initiatives usually address human factors implicitly. This research shows that practices based on human factors indeed perform a crucial role on successful implantations of SPI, proposes change management as a theoretical framework to introduce those practices in the SPI context and suggests some motivational tools based on SPI deployers experience to support it.
Abstract: This paper presents the applicability of artificial
neural networks for 24 hour ahead solar power generation forecasting
of a 20 kW photovoltaic system, the developed forecasting is suitable
for a reliable Microgrid energy management. In total four neural
networks were proposed, namely: multi-layred perceptron, radial
basis function, recurrent and a neural network ensemble consisting in
ensemble of bagged networks. Forecasting reliability of the proposed
neural networks was carried out in terms forecasting error
performance basing on statistical and graphical methods. The
experimental results showed that all the proposed networks achieved
an acceptable forecasting accuracy. In term of comparison the neural
network ensemble gives the highest precision forecasting comparing
to the conventional networks. In fact, each network of the ensemble
over-fits to some extent and leads to a diversity which enhances the
noise tolerance and the forecasting generalization performance
comparing to the conventional networks.
Abstract: In over deployed sensor networks, one approach
to Conserve energy is to keep only a small subset of sensors
active at Any instant. For the coverage problems, the monitoring
area in a set of points that require sensing, called demand points, and
consider that the node coverage area is a circle of range R, where R
is the sensing range, If the Distance between a demand point and
a sensor node is less than R, the node is able to cover this point. We
consider a wireless sensor network consisting of a set of sensors
deployed randomly. A point in the monitored area is covered if it is
within the sensing range of a sensor. In some applications, when the
network is sufficiently dense, area coverage can be approximated by
guaranteeing point coverage. In this case, all the points of wireless
devices could be used to represent the whole area, and the working
sensors are supposed to cover all the sensors. We also introduce
Hybrid Algorithm and challenges related to coverage in sensor
networks.
Abstract: This paper fist examines three set of bivariate cointegrations between any two of current accounts, stock markets, and currency exchange markets in ten Asian countries. Furthermore, we examined the effect of country characters on this bivariate cointegration. Our findings suggest that for three sets of cointegration test, each sample country at least exists one cointegration. India consistently exhibited a bi-directional causal relationship between any two of three indicators. Unlike Pan et al. (2007) and Phylaktis and Ravazzolo (2005), we found that such cointegration is influenced by three characteristics: capital control; flexibility in foreign exchange rates; and the ratio of trade to GDP. These characteristics are the result of liberalization in each Asian country. This implies that liberalization policies are effective on improving the cointegration between any two of financial markets and current account for ten Asian countries.
Abstract: Although the World Wide Web is considered the
largest source of information there exists nowadays, due to its
inherent dynamic characteristics, the task of finding useful and
qualified information can become a very frustrating experience. This
study presents a research on the information mining systems in the
Web; and proposes an implementation of these systems by means of
components that can be built using the technology of Web services.
This implies that they can encompass features offered by a services
oriented architecture (SOA) and specific components may be used by
other tools, independent of platforms or programming languages.
Hence, the main objective of this work is to provide an architecture
to Web mining systems, divided into stages, where each step is a
component that will incorporate the characteristics of SOA. The
separation of these steps was designed based upon the existing
literature. Interesting results were obtained and are shown here.
Abstract: For the efficient and safe use of the cable-stayed
bridge, a design based on the detailed local analysis of the cable anchor
system is required. Also, a theoretical design process for the anchor
system should be prepared and reviewed. Generally, the size of the
fixing pipe in the anchor system is decided according to the
specifications prepared by cable-manufacturing companies, and
accordingly, there is difficulty determining the initial inner diameters
of the fixing pipes. As such, there is no choice but to use the products
with the existing sizes. In this study, the existing design process of the
fixing pipe, is a type of guide pipe anchor in the cable anchor system,
is reviewed, a formula determining the thickness of the fixing pipe is
proposed, and the convenience and validity of the suggested equation
is compared with the results of the existing designs to verify its
convenience and validity.
Abstract: Within the collaborative research center 666 a new
product development approach and the innovative manufacturing
method of linear flow splitting are being developed. So far the design process is supported by 3D-CAD models utilizing User Defined
Features in standard CAD-Systems. This paper now presents new
functions for generating 3D-models of integral sheet metal products with bifurcations using Siemens PLM NX 6. The emphasis is placed
on design and semi-automated insertion of User Defined Features.
Therefore User Defined Features for both, linear flow splitting
and its derivative linear bend splitting, were developed. In order to facilitate the modeling process, an application was developed
that guides through the insertion process. Its usability and dialog layout adapt known standard features. The work presented here has
significant implications on the quality, accurateness and efficiency of the product generation process of sheet metal products with higher
order bifurcations.
Abstract: Online news websites are one of the main and wide areas of Mass Media. Since the nineties several Jordanian newspapers were introduced to the World Wide Web to reach various and large numbers of audiances. Examples of these newspapers that have online version are Al-Rai, Ad-Dustor and AlGhad. Other pure online news websites include Ammon and Rum. The main aim of this study is to evaluate online newspaper websites using two assessment measures; usability and web content. This aim is achieved by using a questionnaire based evaluation which is based on the definition of usability and web content in the ISO document as the standard number 9241-part 11. The results are obtained based on 204 audiences- responses. The results of the research showed that the usability factor is relatively good for all Jordanian online newspapers whereas the web content factor is moderate.
Abstract: Position based routing protocols are the kinds of
routing protocols, which they use of nodes location information,
instead of links information to routing. In position based routing
protocols, it supposed that the packet source node has position
information of itself and it's neighbors and packet destination node.
Greedy is a very important position based routing protocol. In one of
it's kinds, named MFR (Most Forward Within Radius), source node
or packet forwarder node, sends packet to one of it's neighbors with
most forward progress towards destination node (closest neighbor to
destination). Using distance deciding metric in Greedy to forward
packet to a neighbor node, is not suitable for all conditions. If closest
neighbor to destination node, has high speed, in comparison with
source node or intermediate packet forwarder node speed or has very
low remained battery power, then packet loss probability is
increased. Proposed strategy uses combination of metrics distancevelocity
similarity-power, to deciding about giving the packet to
which neighbor. Simulation results show that the proposed strategy
has lower lost packets average than Greedy, so it has more reliability.
Abstract: In this paper, a new approach for design of a fully
differential second order current mode continuous-time sigma-delta
modulator is presented. For circuit implementation, square root
domain (SRD) translinear loop based on floating-gate MOS
transistors that operate in saturation region is employed. The
modulator features, low supply voltage, low power consumption
(8mW) and high dynamic range (55dB). Simulation results confirm
that this design is suitable for data converters.