Abstract: This paper proposes a new performance characterization for the test strategy intended for second order filters denominated Transient Analysis Method (TRAM). We evaluate the ability of the addressed test strategy for detecting deviation faults under simultaneous statistical fluctuation of the non-faulty parameters. For this purpose, we use Monte Carlo simulations and a fault model that considers as faulty only one component of the filter under test while the others components adopt random values (within their tolerance band) obtained from their statistical distributions. The new data reported here show (for the filters under study) the presence of hard-to-test components and relatively low fault coverage values for small deviation faults. These results suggest that the fault coverage value obtained using only nominal values for the non-faulty components (the traditional evaluation of TRAM) seem to be a poor predictor of the test performance.
Abstract: By the application of an improved back-propagation
neural network (BPNN), a model of current densities for a solid oxide
fuel cell (SOFC) with 10 layers is established in this study. To build
the learning data of BPNN, Taguchi orthogonal array is applied to
arrange the conditions of operating parameters, which totally 7 factors
act as the inputs of BPNN. Also, the average current densities
achieved by numerical method acts as the outputs of BPNN.
Comparing with the direct solution, the learning errors for all learning
data are smaller than 0.117%, and the predicting errors for 27
forecasting cases are less than 0.231%. The results show that the
presented model effectively builds a mathematical algorithm to predict
performance of a SOFC stack immediately in real time.
Also, the calculating algorithms are applied to proceed with the
optimization of the average current density for a SOFC stack. The
operating performance window of a SOFC stack is found to be
between 41137.11 and 53907.89. Furthermore, an inverse predicting
model of operating parameters of a SOFC stack is developed here by
the calculating algorithms of the improved BPNN, which is proved to
effectively predict operating parameters to achieve a desired
performance output of a SOFC stack.
Abstract: Avalanche release of snow has been modeled in the present studies. Snow is assumed to be represented by semi-solid and the governing equations have been studied from the concept of continuum approach. The dynamical equations have been solved for two different zones [starting zone and track zone] by using appropriate initial and boundary conditions. Effect of density (ρ), Eddy viscosity (η), Slope angle (θ), Slab depth (R) on the flow parameters have been observed in the present studies. Numerical methods have been employed for computing the non linear differential equations. One of the most interesting and fundamental innovation in the present studies is getting initial condition for the computation of velocity by numerical approach. This information of the velocity has obtained through the concept of fracture mechanics applicable to snow. The results on the flow parameters have found to be in qualitative agreement with the published results.
Abstract: The effect of time-periodic oscillations of the Rayleigh- Benard system on the heat transport in dielectric liquids is investigated by weakly nonlinear analysis. We focus on stationary convection using the slow time scale and arrive at the real Ginzburg- Landau equation. Classical fourth order Runge-kutta method is used to solve the Ginzburg-Landau equation which gives the amplitude of convection and this helps in quantifying the heat transfer in dielectric liquids in terms of the Nusselt number. The effect of electrical Rayleigh number and the amplitude of modulation on heat transport is studied.
Abstract: The effects of coatings based on sodium alginate (S.A) and carboxyl methyl cellulose (CMC) on the color and moisture characteristics of potato round slices were investigated. It is the first time that this combination of polysaccharides is used as edible coating which alone had the best performance as inhibitor of potato color discoloration during the storage of 15 days at 4oC. When ascorbic acid (AA) and green tea (GT) were added in the above edible coating its effects on potato round slices changed. The mixtures of sodium alginate and carboxyl methyl cellulose with ascorbic acid or with green tea behave as a potential moisture barrier, resulting to the extent of potato samples self–life. These data suggests that both GT and AA are potential inhibitors of dehydration in potatoes and not only natural antioxidants.
Abstract: Agriculture products are being more demanding in
market today. To increase its productivity, automation to produce
these products will be very helpful. The purpose of this work is to
measure and determine the ripeness and quality of watermelon. The
textures on watermelon skin will be captured using digital camera.
These images will be filtered using image processing technique. All
these information gathered will be trained using ANN to determine
the watermelon ripeness accuracy. Initial results showed that the best
model has produced percentage accuracy of 86.51%, when measured
at 32 hidden units with a balanced percentage rate of training dataset.
Abstract: fibers of pure cellulose can be made from some bacteria such as acetobacter xylinum. Bacterial cellulose fibers are very pure, tens of nm across and about 0.5 micron long. The fibers are very stiff and, although nobody seems to have measured the strength of individual fibers. Their stiffness up to 70 GPa. Fundamental strengths should be at least greater than those of the best commercial polymers, but best bulk strength seems to about the same as that of steel. They can potentially be produced in industrial quantities at greatly lowered cost and water content, and with triple the yield, by a new process. This article presents a critical review of the available information on the bacterial cellulose as a biological nonwoven fabric with special emphasis on its fermentative production and applications. Characteristics of bacterial cellulose biofabric with respect to its structure and physicochemical properties are discussed. Current and potential applications of bacterial cellulose in textile, nonwoven cloth, paper, films synthetic fiber coating, food, pharmaceutical and other industries are also presented.
Abstract: Task of object localization is one of the major
challenges in creating intelligent transportation. Unfortunately, in
densely built-up urban areas, localization based on GPS only
produces a large error, or simply becomes impossible. New
opportunities arise for the localization due to the rapidly emerging
concept of a wireless ad-hoc network. Such network, allows
estimating potential distance between these objects measuring
received signal level and construct a graph of distances in which
nodes are the localization objects, and edges - estimates of the
distances between pairs of nodes. Due to the known coordinates of
individual nodes (anchors), it is possible to determine the location of
all (or part) of the remaining nodes of the graph. Moreover, road
map, available in digital format can provide localization routines
with valuable additional information to narrow node location search.
However, despite abundance of well-known algorithms for solving
the problem of localization and significant research efforts, there are
still many issues that currently are addressed only partially. In this
paper, we propose localization approach based on the graph mapped
distances on the digital road map data basis. In fact, problem is
reduced to distance graph embedding into the graph representing area
geo location data. It makes possible to localize objects, in some cases
even if only one reference point is available. We propose simple
embedding algorithm and sample implementation as spatial queries
over sensor network data stored in spatial database, allowing
employing effectively spatial indexing, optimized spatial search
routines and geometry functions.
Abstract: Building Sector is the major electricity consumer and
it is costly to building owners. Therefore the application of thermal
energy storage (TES) has gained attractive to reduce energy cost.
Many attractive tariff packages are being offered by the electricity
provider to promote TES. The tariff packages offered higher cost of
electricity during peak period and lower cost of electricity during off
peak period. This paper presented the return of initial investment by
implementing a centralized air-conditioning plant integrated with
thermal energy storage with partially operation strategies. Building
load profile will be calculated hourly according to building
specification and building usage trend. TES operation conditions will
be designed according to building load demand profile, storage
capacity, tariff packages and peak/off peak period. The Payback
Period analysis method was used to evaluate economic analysis. The
investment is considered a good investment where by the initial cost
is recovered less than ten than seven years.
Abstract: This paper may be considered as combination of both pervasive computing and Differential GPS (global positioning satellite) which relates to control automatic traffic signals in such a
way as to pre-empt normal signal operation and permit lifesaving vehicles. Before knowing the arrival of the lifesaving vehicles from
the signal there is a chance of clearing the traffic. Traffic signal
preemption system includes a vehicle equipped with onboard computer system capable of capturing diagnostic information and
estimated location of the lifesaving vehicle using the information provided by GPS receiver connected to the onboard computer system
and transmitting the information-s using a wireless transmitter via a
wireless network. The fleet management system connected to a
wireless receiver is capable of receiving the information transmitted
by the lifesaving vehicle .A computer is also located at the
intersection uses corrected vehicle position, speed & direction
measurements, in conjunction with previously recorded data defining
approach routes to the intersection, to determine the optimum time to
switch a traffic light controller to preemption mode so that lifesaving
vehicles can pass safely. In case when the ambulance need to take a
“U" turn in a heavy traffic area we suggest a solution. Now we are
going to make use of computerized median which uses LINKED
BLOCKS (removable) to solve the above problem.
Abstract: In this study arsenate [As(V)] removal from drinking water by coagulation process was investigated. Ferric chloride (FeCl3.6H2O) and ferrous sulfate (FeSO4.7H2O) were used as coagulant. The effects of major operating variables such as coagulant dose (1–30 mg/L) and pH (5.5–9.5) were investigated. Ferric chloride and ferrous sulfate were found as effective and reliable coagulant due to required dose, residual arsenate and coagulant concentration. Optimum pH values for maximum arsenate removal for ferrous sulfate and ferric chloride were found as 8 and 7.5. The arsenate removal efficiency decreased at neutral and acidic pH values for Fe(II) and at the high acidic and high alkaline pH for Fe(III). It was found that the increase of coagulant dose caused a substantial increase in the arsenate removal. But above a certain ferric chloride and ferrous sulfate dosage, the increase in arsenate removal was not significant. Ferric chloride and ferrous sulfate dose above 8 mg/L slightly increased arsenate removal.
Abstract: Architecture as a form of art, whilst actively
developing, finds new methods and conceptions. Currently,
architectural animation is actively developing as a step, successive to
architectural visualization. Interesting vistas of architectural ideas
were discovered by artists of Japanese animation, in which there are
traditional spirits, kami, and imaginary spaces relating to them.
Anime art should be considered abstract painting, another kind of an
architectural workshop, where new architectural ideas are generated.
Abstract: The effect of concentration of reduction agent of
sodium borohydrate (NaBH4) on the properties of silicon
nanoparticles synthesized via microemulsion route is reported. In
this work, the concentration of the silicon tetrachloride (SiCl4) that
served as silicon source with sodium hydroxide (NaOH) and
polyethylene glycol (PEG) as stabilizer and surfactant, respectively,
are keep fixed. Four samples with varied concentration of NaBH4
from 0.05 M to 0.20 M were synthesized. It was found that the lowest
concentration of NaBH4 gave better formation of silicon
nanoparticles.
Abstract: Despite the internet, which is one of the mass media
that has become quite common in recent years, the relationship of
Advertisement with Television and Cinema, which have always
drawn attention of researchers as basic media and where visual use is
in the foreground, have also become the subject of various studies.
Based on the assumption that the known fundamental effects of
advertisements on consumers are closely related to the creative
process of advertisements as well as the nature and characteristics of
the medium where they are used, these basic mass media (Television
and Cinema) and the consumer motivations of the advertisements
they broadcast have become a focus of study.
Given that the viewers of the mass media in question have shifted
from a passive position to a more active one especially in recent years
and approach contents of advertisements, as they do all contents, in a
more critical and “pitiless" manner, it is possible to say that
individuals make more use of advertisements than in the past and
combine their individual goals with the goals of the advertisements.
This study, which aims at finding out what the goals of these new
individual advertisement use are, how they are shaped by the distinct
characteristics of Television and Cinema, where visuality takes
precedence as basic mass media, and what kind of places they occupy
in the minds of consumers, has determined consumers- motivations
as: “Entertainment", “Escapism", “Play", “Monitoring/Discovery",
“Opposite Sex" and “Aspirations and Role Models".
This study intends to reveal the differences or similarities among
the needs and hence the gratifications of viewers who consume
advertisements on Television or at the Cinema, which are two basic
media where visuality is prioritized.
Abstract: In this article, by means of examination of Bolshevists
Turkistanskie Vedomosti" newspaper and “Erikti Oylar Organi" and
“Turkistanskyi Vestnik" newspapers which had been published
during 1917-1918, the fact that “Turkistan Governorship" established
in city of Kokand in November of 1917, within the framework of
former tsarist Russia Turkistan general-governorship, was the legal
government formed as a requisition of people of Turkistan was
proved. An examination of these two newspapers providing
information regarding history of “Turkistan Autonomy" but having
opposite to each other views makes it possible to obtain valuable data
concerning history of autonomy which was inappropriately
misrepresented during Soviet period.
Abstract: The present work is motivated by the idea that the
layer deformation in anisotropic elasticity can be estimated from the
theory of interfacial dislocations. In effect, this work which is an
extension of a previous approach given by one of the authors
determines the anisotropic displacement fields and the critical
thickness due to a complex biperiodic network of MDs lying just
below the free surface in view of the arrangement of dislocations.
The elastic fields of such arrangements observed along interfaces
play a crucial part in the improvement of the physical properties of
epitaxial systems. New results are proposed in anisotropic elasticity
for hexagonal networks of MDs which contain intrinsic and extrinsic
stacking faults. We developed, using a previous approach based on
the relative interfacial displacement and a Fourier series formulation
of the displacement fields, the expressions of elastic fields when
there is a possible dissociation of MDs. The numerical investigations
in the case of the observed system Si/(111)Si with low twist angles
show clearly the effect of the anisotropy and thickness when the
misfit networks are dissociated.
Abstract: This paper investigates the structure and content of the
wine lists in upscale restaurants in Portugal (N=61). The respondents
considered that a wine list should be easy to use and to modify, welldesigned,
modern and varied. Respondents also stated that they
perform on average 6 revisions to the wine list per year. The
restaurant owner, the restaurant manager and the sommelier were the
main persons in charge of the wine list design. One of the most
important reasons for selecting wines across most restaurants was to
‘complement the menu’ and ‘pairing food with wine’. Restaurants
also reported to be relatively independent from suppliers and
magazine evaluations. Moreover, this work revealed that the
restaurant wine list is considered by restaurateurs as a strategic tool to
sell wine as a complement to the menu, to improve customer
satisfaction and loyalty, to increase restaurant value and to enhance a
successful positioning.
Abstract: Molecular dynamics simulation of annular flow
boiling in a nanochannel with 70000 particles is numerically
investigated. In this research, an annular flow model is developed to
predict the superheated flow boiling heat transfer characteristics in a
nanochannel. To characterize the forced annular boiling flow in a
nanochannel, an external driving force F ext ranging from 1to12PN
(PN= Pico Newton) is applied along the flow direction to inlet fluid
particles during the simulation. Based on an annular flow model
analysis, it is found that saturation condition and superheat degree
have great influences on the liquid-vapor interface. Also, the results
show that due to the relatively strong influence of surface tension in
small channel, the interface between the liquid film and vapor core is
fairly smooth, and the mean velocity along the stream-wise direction
does not change anymore.
Abstract: The present experimental investigation brings about
a comparative study of lactic acid production by pure strains of
Lactobacilli (1) L. delbreuckii (NCIM2025), (2) L. pentosus (NCIM
2912), (3) Lactobacillus sp.(NCIM 2734, (4) Lactobacillus sp.
(NCIM2084) and coculture of strain-1 and Stain-2 in solid bed of
wheat bran, under the influence of different nitrogen sources such as
baker-s yeast, meat extract and proteose peptone. Among the pure
cultures, strain-3 attained lowest pH value of 3.44, hence highest acid
formation 46.41 g/L, while the coculture attained an overall
maximum value 47.56 g/L lactic acid (pH 3.38) at 15 g/L and 20 g/L
level of baker-s yeast, respectively.
Abstract: The current methods of predictive controllers are
utilized for those processes in which the rate of output variations is
not high. For such processes, therefore, stability can be achieved by
implementing the constrained predictive controller or applying
infinite prediction horizon. When the rate of the output growth is
high (e.g. for unstable nonminimum phase process) the stabilization
seems to be problematic. In order to avoid this, it is suggested to
change the method in the way that: first, the prediction error growth
should be decreased at the early stage of the prediction horizon, and
second, the rate of the error variation should be penalized. The
growth of the error is decreased through adjusting its weighting
coefficients in the cost function. Reduction in the error variation is
possible by adding the first order derivate of the error into the cost
function. By studying different examples it is shown that using these
two remedies together, the closed-loop stability of unstable
nonminimum phase process can be achieved.