Abstract: In this work, sorption of nickel from aqueous solution on hypnea valentiae, red macro algae, was investigated. Batch experiments have been carried out to find the effect of various parameters such as pH, temperature, sorbent dosage, metal concentration and contact time on the sorption of nickel using hypnea valentiae. Response surface methodology (RSM) is employed to optimize the process parameters. Based on the central composite design, quadratic model was developed to correlate the process variables to the response. The most influential factor on each experimental design response was identified from the analysis of variance (ANOVA). The optimum conditions for the sorption of nickel were found to be: pH – 5.1, temperature – 36.8oC, sorbent dosage – 5.1 g/L, metal concentration – 100 mg/L and contact time – 30 min. At these optimized conditions the maximum removal of nickel was found to be 91.97%. A coefficient of determination R2 value 0.9548 shows the fitness of response surface methodology in this work.
Abstract: The stop watch is used to measure the time required
for a certain event. This is different from normal clocks in many
ways, one of which is the accuracy of time. The stop watch requires
much more accuracy than the normal clocks. In this paper, an
ATmega8535 microcontroller was used to control the stop watch, by
which perfect accuracy can be ensured. For compiling the C code and
for loading the compiled .hex file into the microcontroller, AVR
studio and PonyProg were used respectively. The stop watch is also
different from traditional stop watches, as it contains two different
timing modes namely 'Split timing' and 'Lap timing'.
Abstract: In recent years there has been a continuous increase of
axle loads, tonnage, train speed and train length which has increased
both the productivity in the rail sector and the risk of rail breaks and
derailments. On the other hand, the environmental requirements (e.g.
noise reduction) for railway operations will become tighter in the
future. In our research we developed a new composite material which
does not change braking properties, is capable of taking extremely
high pressure loads, reduces noise and is environmentally friendly.
Part of our research was also the development of technology which
will be able to apply this material to the rail. The result of our
research was the system which reduces the wear out significantly and
almost completely eliminates the squealing noise at the same time,
and by using only one special material.
Abstract: RFID system, in which we give identification number to each item and detect it with radio frequency, supports more variable service than barcode system can do. For example, a refrigerator with RFID reader and internet connection will automatically notify expiration of food validity to us. But, in spite of its convenience, RFID system has some security threats, because anybody can get ID information of item easily. One of most critical threats is privacy invasion. Existing privacy protection schemes or systems have been proposed, and these schemes or systems defend normal users from attempts that any attacker tries to get information using RFID tag value. But, these systems still have weakness that attacker can get information using analogous value instead of original tag value. In this paper, we mention this type of attack more precisely and suggest 'Tag Broker Model', which can defend it. Tag broker in this model translates original tag value to random value, and user can only get random value. Attacker can not use analogous tag value, because he/she is not able to know original one from it.
Abstract: Collaborative planning, forecasting and
replenishment (CPFR) coordinates the various supply chain
management activities including production and purchase planning,
demand forecasting and inventory replenishment between supply
chain trading partners. This study proposes a systematic way of
analyzing CPFR supporting factors using fuzzy cognitive map
(FCM) approach. FCMs have proven particularly useful for solving
problems in which a number of decision variables and
uncontrollable variables are causally interrelated. Hence the FCMs
of CPFR are created to show the relationships between the factors
that influence on effective implementation of CPFR in the supply
chain.
Abstract: This paper is concerned with calculating boiler
efficiency as one of the most important types of performance
measurements in any steam power plant. That has a key role in
determining the overall effectiveness of the whole system within the
power station. For this calculation, a Visual-Basic program was
developed, and a steam power plant known as El-Khmus power
plant, Libya was selected as a case study. The calculation of the
boiler efficiency was applied by using heating balance method. The
findings showed how the maximum heat energy which produced
from the boiler increases the boiler efficiency through increasing the
temperature of the feed water, and decreasing the exhaust
temperature along with humidity levels of the of fuel used within the
boiler.
Abstract: Recently, the Field Programmable Gate Array (FPGA) technology offers the potential of designing high performance systems at low cost. The discrete wavelet transform has gained the reputation of being a very effective signal analysis tool for many practical applications. However, due to its computation-intensive nature, current implementation of the transform falls short of meeting real-time processing requirements of most application. The objectives of this paper are implement the Haar and Daubechies wavelets using FPGA technology. In addition, the Bit Error Rate (BER) between the input audio signal and the reconstructed output signal for each wavelet is calculated. From the BER, it is seen that the implementations execute the operation of the wavelet transform correctly and satisfying the perfect reconstruction conditions. The design procedure has been explained and designed using the stat-ofart Electronic Design Automation (EDA) tools for system design on FPGA. Simulation, synthesis and implementation on the FPGA target technology has been carried out.
Abstract: This research is aimed at studying the nature of
problems and demands of the training for community leaders in the
upper northeastern region of Thailand. Population and group
samplings are based on 360 community leaders in the region who
have experienced prior training from the Udonthani Rajabhat
University. Stratified random samplings have been drawn upon 186
participants. The research tools is questionnaires. The frequency,
percentage and standard deviation are employed in data analysis. The
findings indicate that most of community leaders are males and
senior adults. The problems in training are associated with the
inconveniences of long-distance travelling to training locations,
inadequacy of learning centers and training sites and high training
costs. The demand of training is basically motivated by a desire for
self-development in modern knowledge in keeping up-to-date with
the changing world and the need for technological application and
facilitation in shortening the distance to training locations and in
limiting expensive training costs.
Abstract: Public procurement is one of the most
important areas in the public sector that introduces a possibility for a
corruption. Due to the volume of the funds that are
allocated through this institution (in the EU countries it is between 10
– 15% of GDP), it has very serious implications for the efficiency of
public expenditures and the overall economic efficiency as
well. Indicators that are usually used for the measurement of the
corruption (such as Corruption Perceptions Index - CPI) show that
the worst situation is in the post-communist countries
and Mediterranean countries.
The presented paper uses the Czech Republic as an example of a
post-communist country and analyses the factors which influence
the scope of corruption in public procurement. Moreover, the
paper discusses indicators that could point at the public procurement
market inefficiency. The presented results show that post-communist
states use the institute of public contracts significantly more than the
old member countries of the continental Europe. It has a very
important implication because it gives more space for corruption.
Furthermore, it appears that the inefficient functioning of public
procurement market is clearly manifested in the low number of bids,
low level of market transparency and an ineffective control
system. Some of the observed indicators are statistically significantly
correlated with the CPI.
Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: This article is presented an experimental and modeling
study of a four-bed pressure swing adsorption process using
zeolite13X to provide oxygen-enriched air. The binary mixture N2/O2
(79/21 vol %) was used as a feed stream. The effects of purge/feed
ratio (P/F), adsorption pressure, cyclic time and product flow rate on
product purity and recovery under nonisothermal condition were
studied. The adsorption dynamics of process were determined using
a mathematical model incorporated mass and energy balances. A
Mathlab code using finite difference method was developed to solve
the set of coupled differential-algebraic equations, and the simulation
results are agreed well with experimental results.
Abstract: This paper examines the available experiment data for a copper bromide vapor laser (CuBr laser), emitting at two wavelengths - 510.6 and 578.2nm. Laser output power is estimated based on 10 independent input physical parameters. A classification and regression tree (CART) model is obtained which describes 97% of data. The resulting binary CART tree specifies which input parameters influence considerably each of the classification groups. This allows for a technical assessment that indicates which of these are the most significant for the manufacture and operation of the type of laser under consideration. The predicted values of the laser output power are also obtained depending on classification. This aids the design and development processes considerably.
Abstract: Total weighted tardiness is a measure of customer
satisfaction. Minimizing it represents satisfying the general
requirement of on-time delivery. In this research, we consider an ant
colony optimization (ACO) algorithm to solve the problem of
scheduling unrelated parallel machines to minimize total weighted
tardiness. The problem is NP-hard in the strong sense. Computational
results show that the proposed ACO algorithm is giving promising
results compared to other existing algorithms.
Abstract: Mammalian genomes contain large number of
retroelements (SINEs, LINEs and LTRs) which could affect
expression of protein coding genes through associated transcription
factor binding sites (TFBS). Activity of the retroelement-associated
TFBS in many genes is confirmed experimentally but their global
functional impact remains unclear. Human SINEs (Alu repeats) and
mouse SINEs (B1 and B2 repeats) are known to be clustered in GCrich
gene rich genome segments consistent with the view that they
can contribute to regulation of gene expression. We have shown
earlier that Alu are involved in formation of cis-regulatory modules
(clusters of TFBS) in human promoters, and other authors reported
that Alu located near promoter CpG islands have an increased
frequency of CpG dinucleotides suggesting that these Alu are
undermethylated. Human Alu and mouse B1/B2 elements have an
internal bipartite promoter for RNA polymerase III containing
conserved sequence motif called B-box which can bind basal
transcription complex TFIIIC. It has been recently shown that TFIIIC
binding to B-box leads to formation of a boundary which limits
spread of repressive chromatin modifications in S. pombe. SINEassociated
B-boxes may have similar function but conservation of
TFIIIC binding sites in SINEs located near mammalian promoters
has not been studied earlier. Here we analysed abundance and
distribution of retroelements (SINEs, LINEs and LTRs) in annotated
sequences of the Database of mammalian transcription start sites
(DBTSS). Fractions of SINEs in human and mouse promoters are
slightly lower than in all genome but >40% of human and mouse
promoters contain Alu or B1/B2 elements within -1000 to +200 bp
interval relative to transcription start site (TSS). Most of these SINEs
is associated with distal segments of promoters (-1000 to -200 bp
relative to TSS) indicating that their insertion at distances >200 bp
upstream of TSS is tolerated during evolution. Distribution of SINEs
in promoters correlates negatively with the distribution of CpG
sequences. Using analysis of abundance of 12-mer motifs from the
B1 and Alu consensus sequences in genome and DBTSS it has been
confirmed that some subsegments of Alu and B1 elements are poorly
conserved which depends in part on the presence of CpG
dinucleotides. One of these CpG-containing subsegments in B1
elements overlaps with SINE-associated B-box and it shows better
conservation in DBTSS compared to genomic sequences. It has been
also studied conservation in DBTSS and genome of the B-box
containing segments of old (AluJ, AluS) and young (AluY) Alu
repeats and found that CpG sequence of the B-box of old Alu is
better conserved in DBTSS than in genome. This indicates that Bbox-
associated CpGs in promoters are better protected from
methylation and mutation than B-box-associated CpGs in genomic
SINEs. These results are consistent with the view that potential
TFIIIC binding motifs in SINEs associated with human and mouse
promoters may be functionally important. These motifs may protect
promoters from repressive histone modifications which spread from
adjacent sequences. This can potentially explain well known
clustering of SINEs in GC-rich gene rich genome compartments and
existence of unmethylated CpG islands.
Abstract: In this paper we consider a nonlinear feedback control called augmented automatic choosing control (AACC) for nonlinear systems with constrained input. Constant terms which arise from section wise linearization of a given nonlinear system are treated as coefficients of a stable zero dynamics.Parameters included in the control are suboptimally selectedby extremizing a combination of Hamiltonian and Lyapunov functions with the aid of the genetic algorithm. This approach is applied to a field excitation control problem of power system to demonstrate the splendidness of the AACC. Simulation results show that the new controller can improve performance remarkably well.
Abstract: In this paper we study numerical methods for solving Sylvester matrix equations of the form AX +XBT +CDT = 0. A new projection method is proposed. The union of Krylov subspaces in A and its inverse and the union of Krylov subspaces in B and its inverse are used as the right and left projection subspaces, respectively. The Arnoldi-like process for constructing the orthonormal basis of the projection subspaces is outlined. We show that the approximate solution is an exact solution of a perturbed Sylvester matrix equation. Moreover, exact expression for the norm of residual is derived and results on finite termination and convergence are presented. Some numerical examples are presented to illustrate the effectiveness of the proposed method.
Abstract: In this paper, we validate crater detection in moon surface image using FLDA. This proposal assumes that it is applied to SLIM (Smart Lander for Investigating Moon) project aiming at the pin-point landing to the moon surface. The point where the lander should land is judged by the position relations of the craters obtained via camera, so the real-time image processing becomes important element. Besides, in the SLIM project, 400kg-class lander is assumed, therefore, high-performance computers for image processing cannot be equipped. We are studying various crater detection methods such as Haar-Like features, LBP, and PCA. And we think these methods are appropriate to the project, however, to identify the unlearned images obtained by actual is insufficient. In this paper, we examine the crater detection using FLDA, and compare with the conventional methods.
Abstract: This paper features the trajectory planning design of a indigenously developed 4-Axis SCARA robot which is used for doing successful robotic manipulation task in the laboratory. Once, a trajectory is being designed and given as input to the robot, the robot's gripper tip moves along that specified trajectory. Trajectories have to be designed in the work space only. The main idea of this paper is to design a continuous path trajectory model for the indigenously developed SCARA robot arm during its maneuvering from one point to another point (during pick and place operations) in a workspace avoiding all the obstacles in its path of motion.
Abstract: This paper proposes an adaptive sliding mode
controller which combines adaptive control and sliding
mode control to control a nonlinear robotic manipulator
with uncertain parameters. We use an adaptive algorithm
based on the concept of sliding mode control to alleviate the
chattering phenomenon of control input. Adaptive laws are
developed to obtain the gain of switching input and the
boundary layer parameters. The stability and convergence
of the robotic manipulator control system are guaranteed
by applying the Lyapunov theorem. Simulation results
demonstrate that the chattering of control input can be
alleviated effectively. The proposed controller scheme can
assure robustness against a large class of uncertainties and
achieve good trajectory tracking performance.
Abstract: A graph G is fractional k-covered if for each edge e of
G, there exists a fractional k-factor h, such that h(e) = 1. If k = 2,
then a fractional k-covered graph is called a fractional 2-covered
graph. The binding number bind(G) is defined as follows,
bind(G) = min{|NG(X)|
|X|
: ├ÿ = X Ôèå V (G),NG(X) = V (G)}.
In this paper, it is proved that G is fractional 2-covered if δ(G) ≥ 4
and bind(G) > 5
3 .