Abstract: In this paper, the torsion capacity of ultimate point on rectangular beams with spiral reinforcements in the torsion direction and its anti-direction are investigated. Therefore, models of above-mentioned beams have been numerically analyzed under various loads using ANSYS software. It was observed that, spirallyreinforced prismatic beam and beam with spiral links, show lower torsion capacity than beam with normal links also in anti-direction. The result is that the concrete regulations are violated in this case.
Abstract: This study applied the Gaussian trajectory
transfer-coefficient model (GTx) to simulate the particulate matter
concentrations and the source apportionments at Nanzih Air Quality
Monitoring Station in southern Taiwan from November 2007 to
February 2008. The correlation coefficient between the observed and
the calculated daily PM10 concentrations is 0.5 and the absolute bias of
the PM10 concentrations is 24%. The simulated PM10 concentrations
matched well with the observed data. Although the emission rate of
PM10 was dominated by area sources (58%), the results of source
apportionments indicated that the primary sources for PM10 at Nanzih
Station were point sources (42%), area sources (20%) and then upwind
boundary concentration (14%). The obvious difference of PM10 source
apportionment between episode and non-episode days was upwind
boundary concentrations which contributed to 20% and 11% PM10
sources, respectively. The gas-particle conversion of secondary
aerosol and long range transport played crucial roles on the PM10
contribution to a receptor.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: This paper addresses the problem of forbidden states in
non safe Petri Nets. In the system, for preventing it from entering the
forbidden states, some linear constraints can be assigned to them.
Then these constraints can be enforced on the system using control
places. But when the number of constraints in the system is large, a
large number of control places must be added to the model of system.
This concept complicates the model of system. There are some
methods for reducing the number of constraints in safe Petri Nets.
But there is no a systematic method for non safe Petri Nets. In this
paper we propose a method for reducing the number of constraints in
non safe Petri Nets which is based on solving an integer linear
programming problem.
Abstract: This article deals with the conceptual modeling under uncertainty. First, the division of information systems with their definition will be described, focusing on those where the construction of a conceptual model is suitable for the design of future information system database. Furthermore, the disadvantages of the traditional approach in creating a conceptual model and database design will be analyzed. A comprehensive methodology for the creation of a conceptual model based on analysis of client requirements and the selection of a suitable domain model is proposed here. This article presents the expert system used for the construction of a conceptual model and is a suitable tool for database designers to create a conceptual model.
Abstract: Nowadays, the pace of business change is such that,
increasingly, new functionality has to be realized and reliably
installed in a matter of days, or even hours. Consequently, more and
more business processes are prone to a continuous change. The
objective of the research in progress is to use the MAP model, in a
conceptual modeling method for flexible and adaptive business
process. This method can be used to capture the flexibility
dimensions of a business process; it takes inspiration from
modularity concept in the object oriented paradigm to establish a
hierarchical construction of the BP modeling. Its intent is to provide
a flexible modeling that allows companies to quickly adapt their
business processes.
Abstract: In order to study of hydropriming and halopriming on
germination and early growth stage of wheat (Triticum aestivum) an
experiment was carried out in laboratory of the Department of
Agronomy and Plant breeding, Shahrood University of Technology.
Seed treatments consisted of T1: control (untreated seeds), T2:
soaking in distilled water for 18 h (hydropriming). T3: soaking in -
1.2 MPa solution of CaSO4 for 36 h (halopriming). Germination and
early seedling growth were studied using distilled water (control) and
under osmotic potentials of -0.4, -0.8 and -1.2 MPa for NaCl and
polyethylene glycol (PEG 6000), respectively. Results showed that
Hydroprimed seeds achieved maximum germination seedling dry
weight, especially during the higher osmotic potentials. Minimum
germination was recorded at untreated seeds (control) followed by
osmopriming. Under high osmotic potentials, hydroprimed seeds had
higher GI (germination index) as compared to haloprimed or
untreated seeds. Interaction effect of seed treatment and osmotic
potential significantly affected the seedling vigour index (SVI).
Abstract: This research aims to study the preferable tourism and
the elements of choosing tourist destination from domestic tourist in
Bangkok and the nearby areas in Thailand.The data were collected by
using 1249 set of questionnaires, in mid-August 2012. The result
illustrates that religious destinations are the most preferable places
for the tourist. The average expense per travel is approximately 47
USD a time. Travellers travel based on the advertisement in the
television and internet and their decisions is based on the reputation
of the destinations.
The result on a place dimension demonstrates the neatness and
well managed location play a crucial role on tourist destination.
Gender, age, marriage status and their origins are affecting their
spending and travelling behaviour. The researcher reckon that
providing the area of arcade, selling the souvenir and promoting
tourism among a young professional group would be an important
key follow the income distribution policy, including managing the
destination to welcome the family group, which the result is to
identified as the highest spending.
Abstract: The purpose of this study is to suggest energy efficient
routing for ad hoc networks which are composed of nodes with limited
energy. There are diverse problems including limitation of energy
supply of node, and the node energy management problem has been
presented. And a number of protocols have been proposed for energy
conservation and energy efficiency. In this study, the critical point of
the EA-MPDSR, that is the type of energy efficient routing using only
two paths, is improved and developed. The proposed TP-MESR uses
multi-path routing technique and traffic prediction function to increase
number of path more than 2. It also verifies its efficiency compared to
EA-MPDSR using network simulator (NS-2). Also, To give a
academic value and explain protocol systematically, research
guidelines which the Hevner(2004) suggests are applied. This
proposed TP-MESR solved the existing multi-path routing problem
related to overhead, radio interference, packet reassembly and it
confirmed its contribution to effective use of energy in ad hoc
networks.
Abstract: In this paper, we study FPGA implementation of a
novel supra-optimal receiver diversity combining technique,
generalized maximal ratio combining (GMRC), for wireless
transmission over fading channels in SIMO systems. Prior
published results using ML-detected GMRC diversity signal
driven by BPSK showed superior bit error rate performance to
the widely used MRC combining scheme in an imperfect
channel estimation (ICE) environment. Under perfect channel
estimation conditions, the performance of GMRC and MRC
were identical. The main drawback of the GMRC study was
that it was theoretical, thus successful FPGA implementation
of it using pipeline techniques is needed as a wireless
communication test-bed for practical real-life situations.
Simulation results showed that the hardware implementation
was efficient both in terms of speed and area. Since diversity
combining is especially effective in small femto- and picocells,
internet-associated wireless peripheral systems are to
benefit most from GMRC. As a result, many spinoff
applications can be made to the hardware of IP-based 4th
generation networks.
Abstract: Having considered tactile sensing and palpation of a
surgeon in order to detect kidney stone during open surgery; we
present the 2D model of nephrolithiasis (two dimensional model of
kidney containing a simulated stone). The effects of stone existence
that appear on the surface of kidney (because of exerting mechanical
load) are determined. Using Finite element method, it is illustrated
that the created stress patterns on the surface of kidney and stress
graphs not only show existence of stone inside kidney, but also show
its exact location.
Abstract: The most common type of controller being used in
the industry is PI(D) controller which has been used since 1945 and
is still being widely used due to its efficiency and simplicity. In
most cases, the PI(D) controller was tuned without taking into
consideration of the effect of actuator saturation. In real processes,
the most common actuator which is valve will act as constraint and
restrict the controller output. Since the controller is not designed to
encounter saturation, the process may windup and consequently
resulted in large oscillation or may become unstable. Usually, an
antiwindup compensator is added to the feedback control loop to
reduce the deterioration effect of integral windup. This research
aims to specifically control processes with constraints. The
proposed method was applied to two different types of food
processes, which are blending and spray drying. Simulations were
done using MATLAB and the performances of the proposed
method were compared with other conventional methods. The
proposed technique was able to control the processes and avoid
saturation such that no anti windup compensator is needed.
Abstract: Composite steel-concrete slabs using thin-walled
corrugated steel sheets with embossments represent a modern and
effective combination of steel and concrete. However, the design
of new types of sheeting is conditional on the execution of expensive
and time-consuming laboratory testing. The effort to develop
a cheaper and faster method has lead to many investigations all over
the world. In our paper we compare the results from our experiments
involving vacuum loading, four-point bending and small-scale shear
tests.
Abstract: The experimental and theoretical results of a ZVS
(Zero Voltage Switching) isolated flyback DC-DC converter using
multilayered coreless PCB step down 2:1 transformer are presented.
The performance characteristics of the transformer are shown which
are useful for the parameters extraction. The measured energy
efficiency of the transformer is found to be more than 94% with the
sinusoidal input voltage excitation. The designed flyback converter
has been tested successfully upto the output power level of 10W,
with a switching frequency in the range of 2.7MHz-4.3MHz. The
input voltage of the converter is varied from 25V-40V DC.
Frequency modulation technique is employed by maintaining
constant off time to regulate the output voltage of the converter. The
energy efficiency of the isolated flyback converter circuit under ZVS
condition in the MHz frequency region is found to be approximately
in the range of 72-84%. This paper gives the comparative results in
terms of the energy efficiency of the hard switched and soft switched
flyback converter in the MHz frequency region.
Abstract: Restructured electricity markets may provide
opportunities for producers to exercise market power maintaining
prices in excess of competitive levels. In this paper an oligopolistic
market is presented that all Generation Companies (GenCos) bid in a
Cournot model. Genetic algorithm (GA) is applied to obtain
generation scheduling of each GenCo as well as hourly market
clearing prices (MCP). In order to consider network constraints a
multiperiod framework is presented to simulate market clearing
mechanism in which the behaviors of market participants are
modelled through piecewise block curves. A mixed integer linear
programming (MILP) is employed to solve the problem. Impacts of
market clearing process on participants- characteristic and final
market prices are presented. Consequently, a novel multi-objective
model is addressed for security constrained optimal bidding strategy
of GenCos. The capability of price-maker GenCos to alter MCP is
evaluated through introducing an effective-supply curve. In addition,
the impact of exercising market power on the variation of market
characteristics as well as GenCos scheduling is studied.
Abstract: A comparative evaluation of acute toxicity of
synthesized nano silvers using two different procedures (biological
and chemical reduction methods) and silver ions on bacteria
Vibrio fischeri was investigated. The bacterial light inhibition test as
a toxicological endpoint was used by applying of a homemade
luminometer. To compare the toxicity effects as a quantitative
parameter, a nominal effective concentrations (EC) of chemicals and
a susceptibility constant (Z-value) of bacteria, after 5 min and 30 min
exposure times, were calculated. After 5 and 30 min contact times,
the EC50 values of two silver nanoparticles and the EC20 values were
about similar. It demonstrates that toxicity of silvers was independent
of their procedure. The EC values of nanoparticles were larger than
those of the silver ions. The susceptibilities(Z- Values) of V.fischeri
(L/mg) to the silver ions were greater than those of the nano silvers.
According to the EC and Z values, the toxicity of silvers decreased in
the following order: Silver ions >> silver nanoparticles from
chemical reduction method ~ silver nanoparticles from biological
method.
Abstract: In this paper a PID control strategy using neural
network adaptive RASP1 wavelet for WECS-s control is proposed.
It is based on single layer feedforward neural networks with hidden
nodes of adaptive RASP1 wavelet functions controller and an infinite
impulse response (IIR) recurrent structure. The IIR is combined by
cascading to the network to provide double local structure resulting
in improving speed of learning. This particular neuro PID controller
assumes a certain model structure to approximately identify the
system dynamics of the unknown plant (WECS-s) and generate the
control signal. The results are applied to a typical turbine/generator
pair, showing the feasibility of the proposed solution.
Abstract: In this paper, a novel method using Bees Algorithm is proposed to determine the optimal allocation of FACTS devices for maximizing the Available Transfer Capability (ATC) of power transactions between source and sink areas in the deregulated power system. The algorithm simultaneously searches the FACTS location, FACTS parameters and FACTS types. Two types of FACTS are simulated in this study namely Thyristor Controlled Series Compensator (TCSC) and Static Var Compensator (SVC). A Repeated Power Flow with FACTS devices including ATC is used to evaluate the feasible ATC value within real and reactive power generation limits, line thermal limits, voltage limits and FACTS operation limits. An IEEE30 bus system is used to demonstrate the effectiveness of the algorithm as an optimization tool to enhance ATC. A Genetic Algorithm technique is used for validation purposes. The results clearly indicate that the introduction of FACTS devices in a right combination of location and parameters could enhance ATC and Bees Algorithm can be efficiently used for this kind of nonlinear integer optimization.
Abstract: In this paper we present the algorithm which allows
us to have an object tracking close to real time in Full HD videos.
The frame rate (FR) of a video stream is considered to be between
5 and 30 frames per second. The real time track building will be
achieved if the algorithm can follow 5 or more frames per second. The
principle idea is to use fast algorithms when doing preprocessing to
obtain the key points and track them after. The procedure of matching
points during assignment is hardly dependent on the number of points.
Because of this we have to limit pointed number of points using the
most informative of them.
Abstract: Bone material is treated as heterogeneous and hierarchical in nature therefore appropriate size of bone specimen is required to analyze its tensile properties at a particular hierarchical level. Tensile properties of cortical bone are important to investigate the effect of drug treatment, disease and aging as well as for development of computational and analytical models. In the present study tensile properties of buffalo as well as goat femoral and tibiae cortical bone are analyzed using sub-size tensile specimens. Femoral cortical bone was found to be stronger in tension as compared to the tibiae cortical bone and the tensile properties obtained using sub-size specimens show close resemblance with the tensile properties of full-size cortical specimens. A two dimensional finite element (FE) modal was also applied to simulate the tensile behavior of sub-size specimens. Good agreement between experimental and FE model was obtained for sub-size tensile specimens of cortical bone.