Abstract: In this paper, the influencing parameters of a novel
purely mechanical wireless in-mould injection moulding sensor
were investigated. The sensor is capable of detecting the melt
front at predefined locations inside the mould. The sensor comprises
a movable pin which acts as the sensor element generating
structure-borne sound triggered by the passing melt front. Due to
the sensor design, melt pressure is the driving force. For pressure
level measurement during pin movement a pressure transducer
located at the same position as the movable pin. By deriving
a mathematical model for the mechanical movement, dominant
process parameters could be investigated towards their impact
on the melt front detection characteristic. It was found that the
sensor is not affected by the investigated parameters enabling it
for reliable melt front detection. In addition, it could be proved
that the novel sensor is in comparable range to conventional melt
front detection sensors.
Abstract: Wireless Sensor Networks (WSNs) are used to monitor/observe vast inaccessible regions through deployment of large number of sensor nodes in the sensing area. For majority of WSN applications, the collected data needs to be combined with geographic information of its origin to make it useful for the user; information received from remote Sensor Nodes (SNs) that are several hops away from base station/sink is meaningless without knowledge of its source. In addition to this, location information of SNs can also be used to propose/develop new network protocols for WSNs to improve their energy efficiency and lifetime. In this paper, range free localization protocols for WSNs have been proposed. The proposed protocols are based on weighted centroid localization technique, where the edge weights of SNs are decided by utilizing fuzzy logic inference for received signal strength and link quality between the nodes. The fuzzification is carried out using (i) Mamdani, (ii) Sugeno, and (iii) Combined Mamdani Sugeno fuzzy logic inference. Simulation results demonstrate that proposed protocols provide better accuracy in node localization compared to conventional centroid based localization protocols despite presence of unintentional radio frequency interference from radio frequency (RF) sources operating in same frequency band.
Abstract: The charge-pump circuit is an important component in a phase-locked loop (PLL). The charge-pump converts Up and Down signals from the phase/frequency detector (PFD) into current. A conventional CMOS charge-pump circuit consists of two switched current sources that pump charge into or out of the loop filter according to two logical inputs. The mismatch between the charging current and the discharging current causes phase offset and reference spurs in a PLL. We propose a new charge-pump circuit to reduce the current mismatch by using a regulated cascode circuit. The proposed charge-pump circuit is designed and simulated by spectre with TSMC 0.18-μm 1.8-V CMOS technology.
Abstract: Deaminated lesions were produced via nitrosative oxidation of natural nucleobases; uracul (Ura, U) from cytosine (Cyt, C), hypoxanthine (Hyp, H) from adenine (Ade, A), and xanthine (Xan, X) and oxanine (Oxa, O) from guanine (Gua, G). Such damaged nucleobases may induce mutagenic problems, so that much attentions and efforts have been poured on the revealing of their mechanisms in vivo or in vitro. In this study, we employed these deaminated lesions as useful probes for analysis of DNA-binding/recognizing proteins or enzymes. Since the pyrimidine lesions such as Hyp, Oxa and Xan are employed as analogues of guanine, their comparative uses are informative for analyzing the role of Gua in DNA sequence in DNA-protein interaction. Several DNA oligomers containing such Hyp, Oxa or Xan substituted for Gua were designed to reveal the molecular interaction between DNA and protein. From this approach, we have got useful information to understand the molecular mechanisms of the DNA-recognizing enzymes, which have not ever been observed using conventional DNA oligomer composed of just natural nucleobases.
Abstract: Public awareness towards green energy are on the rise and this can be prove by many product being manufactured or prerequired to be made as energy saving devices mainly to save consumer from spending more on utility billing. These schemes are popular nowadays and many homemade appliances are turned into energy saving gadget which attracts the attention of consumers. Knowing the public demands and pattern towards purchasing home appliances thus the idea of “energy saving suction hood (ESSH)" is proposed. The ESSH can be used in many places that require smoke ventilation or even to reduce the room temperature as many conventional suction hoods (CSH) do, but this device works automatically by the usage of sensors that detects the smoke/temperature and automatically spins the exhaust fan. As it turns, the mechanical rotation rotates the AC generator which is coupled together with the fan and then charges the battery. The innovation of this product is, it does not rely on the utility supply as it is also hook up with a solar panel which also charges the battery, Secondly, it generates energy as the exhaust fan mechanically rotates. Thirdly, an energy loop back feature is introduced to this system which will supply for the ventilator fan. Another major innovation is towards interfacing this device with an in house production of generator. This generator is produced by proper design on stator as well as rotor to reduce the losses. A comparison is made between the ESSH and the CSH and result shows that the ESSH saves 172.8kWh/year of utility supply which is used by CSH. This amount of energy can save RM 3.14 from monthly utility bill and a total of RM 37.67 per year. In fact this product can generate 175 Watt of power from generator(75W) and solar panel(100W) that can be used either to supply other household appliances and/or to loop back to supply the fans motor. The innovation of this system is essential for future production of other equipment by using the loopback power method and turning most equipment into a standalone system.
Abstract: The article deals with the relation between rainfall in selected months and subsequent weed infestation of spring barley. The field experiment was performed at Mendel University agricultural enterprise in Žabčice, Czech Republic. Weed infestation was measured in spring barley vegetation in years 2004 to 2012. Barley was grown in three tillage variants: conventional tillage technology (CT), minimization tillage technology (MT), and no tillage (NT). Precipitation was recorded in one-day intervals. Monthly precipitation was calculated from the measured values in the months of October through to April. The technique of canonical correspondence analysis was applied for further statistical processing. 41 different species of weeds were found in the course of the 9-year monitoring period. The results clearly show that precipitation affects the incidence of most weed species in the selected months, but acts differently in the monitored variants of tillage technologies.
Abstract: In this paper, a low noise microwave bandpass filter
(BPF) is presented. This filter is fabricated by modifying the
conventional cross-coupled structure. The spurious response is
improved by using the end open coupled lines, and the influence of the
noise is minimized. Impedance matrix of the open end coupled circuit
clarifies the characteristic of the suppression of the spurious response.
The rejection of spurious suppression region of the proposed filter is
greater than 20 dB from 3-13 GHz. The measured results of the
fabricated filter confirm the concepts of the proposed design and
exhibits high performance.
Abstract: The use of a Bayesian Hierarchical Model (BHM) to interpret breath measurements obtained during a 13C Octanoic Breath Test (13COBT) is demonstrated. The statistical analysis was implemented using WinBUGS, a commercially available computer package for Bayesian inference. A hierarchical setting was adopted where poorly defined parameters associated with a delayed Gastric Emptying (GE) were able to "borrow" strength from global distributions. This is proved to be a sufficient tool to correct model's failures and data inconsistencies apparent in conventional analyses employing a Non-linear least squares technique (NLS). Direct comparison of two parameters describing gastric emptying ng ( tlag -lag phase, t1/ 2 -half emptying time) revealed a strong correlation between the two methods. Despite our large dataset ( n = 164 ), Bayesian modeling was fast and provided a successful fitting for all subjects. On the contrary, NLS failed to return acceptable estimates in cases where GE was delayed.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.
Abstract: This research work takes a different approach in
the discussion of urban form impacts on transport planning and
auto dependency. Concentrated density represented by effective
density explains auto dependency better than the conventional
density and it is proved to be a realistic density representative for
the urban transportation analysis. Model analysis reveals that
effective density is influenced by the shopping accessibility
index as well as job density factor. It is also combined with the
job access variable to classify four levels of Transport Activity
Centers (TACs) in Okinawa, Japan. Trip attraction capacity and
levels of the newly classified TACs was found agreeable with the
amount of daily trips attracted to each center. The trip attraction
data set was drawn from a 2007 Okinawa personal trip survey.
This research suggests a planning methodology which guides
logical transport supply routes and concentrated local
development schemes.
Abstract: This research is part of a broad program aimed at
advancing the science and technology involved in the rescue and
rehabilitation of oiled wildlife. One aspect of this research involves
the use of oil-sequestering magnetic particles for the removal of
contaminants from plumage – so-called “magnetic cleansing". This
treatment offers a number of advantages over conventional
detergent-based methods including portability - which offers the
possibility of providing a “quick clean" to the animal upon first
encounter in the field. This could be particularly advantageous
when the contaminant is toxic and/or corrosive and/or where there
is a delay in transporting the victim to a treatment centre. The
method could also be useful as part of a stabilization protocol when
large numbers of affected animals are awaiting treatment. This
presentation describes the design, development and testing of a
prototype field kit for providing a “quick clean" to contaminated
wildlife in the field.
Abstract: One of the most common practices for strengthening
the reinforced concrete structures is the application of FRP (Fiber
Reinforce Plastic) sheets to increase the flexural and shear strengths
of the member. The elastic modulus of FRP is considerably higher
than that of concrete. This will result in debonding between the FRP
sheets and concrete surface. With conventional surface preparation of
concrete, the ultimate capacity of the FRP sheets can hardly be
achieved. New methods for preparation of the bonding surface have
shown improvements in reducing the premature debonding of FRP
sheets from concrete surface. The present experimental study focuses
on the application of grooving method to postpone debonding of the
FRP sheets attached to the side faces of concrete beams for shear
strengthening. Comparison has also been made with conventional
surface preparation method. This study clearly shows the efficiency
of grooving method compared to surface preparation method, in
preventing the debonding phenomenon and in increasing the load
carrying capacity of FRP.
Abstract: An enhanced particle swarm optimization algorithm
(PSO) is presented in this work to solve the non-convex OPF
problem that has both discrete and continuous optimization variables.
The objective functions considered are the conventional quadratic
function and the augmented quadratic function. The latter model
presents non-differentiable and non-convex regions that challenge
most gradient-based optimization algorithms. The optimization
variables to be optimized are the generator real power outputs and
voltage magnitudes, discrete transformer tap settings, and discrete
reactive power injections due to capacitor banks. The set of equality
constraints taken into account are the power flow equations while the
inequality ones are the limits of the real and reactive power of the
generators, voltage magnitude at each bus, transformer tap settings,
and capacitor banks reactive power injections. The proposed
algorithm combines PSO with Newton-Raphson algorithm to
minimize the fuel cost function. The IEEE 30-bus system with six
generating units is used to test the proposed algorithm. Several cases
were investigated to test and validate the consistency of detecting
optimal or near optimal solution for each objective. Results are
compared to solutions obtained using sequential quadratic
programming and Genetic Algorithms.
Abstract: Development of artificial neural network (ANN) for
prediction of aluminum workpieces' surface roughness in ultrasonicvibration
assisted turning (UAT) has been the subject of the present
study. Tool wear as the main cause of surface roughness was also
investigated. ANN was trained through experimental data obtained
on the basis of full factorial design of experiments. Various
influential machining parameters were taken into consideration. It
was illustrated that a multilayer perceptron neural network could
efficiently model the surface roughness as the response of the
network, with an error less than ten percent. The performance of the
trained network was verified by further experiments. The results of
UAT were compared with the results of conventional turning
experiments carried out with similar machining parameters except for
the vibration amplitude whence considerable reduction was observed
in the built-up edge and the surface roughness.
Abstract: In this study a neural network (NN) was proposed to
predict the sorption of binary mixture of copper-cobalt ions into
clinoptilolite as ion-exchanger. The configuration of the
backpropagation neural network giving the smallest mean square
error was three-layer NN with tangent sigmoid transfer function at
hidden layer with 10 neurons, linear transfer function at output layer
and Levenberg-Marquardt backpropagation training algorithm.
Experiments have been carried out in the batch reactor to obtain
equilibrium data of the individual sorption and the mixture of coppercobalt
ions. The obtained modeling results have shown that the used
of neural network has better adjusted the equilibrium data of the
binary system when compared with the conventional sorption
isotherm models.
Abstract: As networking has become popular, Web-learning
tends to be a trend while designing a tool. Moreover, five-axis
machining has been widely used in industry recently; however, it has
potential axial table colliding problems. Thus this paper aims at
proposing an efficient web-learning collision detection tool on
five-axis machining. However, collision detection consumes heavy
resource that few devices can support, thus this research uses a
systematic approach based on web knowledge to detect collision. The
methodologies include the kinematics analyses for five-axis motions,
separating axis method for collision detection, and computer
simulation for verification. The machine structure is modeled as STL
format in CAD software. The input to the detection system is the
g-code part program, which describes the tool motions to produce the
part surface. This research produced a simulation program with C
programming language and demonstrated a five-axis machining
example with collision detection on web site. The system simulates the
five-axis CNC motion for tool trajectory and detects for any collisions
according to the input g-codes and also supports high-performance
web service benefiting from C. The result shows that our method
improves 4.5 time of computational efficiency, comparing to the
conventional detection method.
Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Abstract: In this paper, we propose a face recognition algorithm
using AAM and Gabor features. Gabor feature vectors which are well
known to be robust with respect to small variations of shape, scaling,
rotation, distortion, illumination and poses in images are popularly
employed for feature vectors for many object detection and
recognition algorithms. EBGM, which is prominent among face
recognition algorithms employing Gabor feature vectors, requires
localization of facial feature points where Gabor feature vectors are
extracted. However, localization method employed in EBGM is based
on Gabor jet similarity and is sensitive to initial values. Wrong
localization of facial feature points affects face recognition rate. AAM
is known to be successfully applied to localization of facial feature
points. In this paper, we devise a facial feature point localization
method which first roughly estimate facial feature points using AAM
and refine facial feature points using Gabor jet similarity-based facial
feature localization method with initial points set by the rough facial
feature points obtained from AAM, and propose a face recognition
algorithm using the devised localization method for facial feature
localization and Gabor feature vectors. It is observed through
experiments that such a cascaded localization method based on both
AAM and Gabor jet similarity is more robust than the localization
method based on only Gabor jet similarity. Also, it is shown that the
proposed face recognition algorithm using this devised localization
method and Gabor feature vectors performs better than the
conventional face recognition algorithm using Gabor jet
similarity-based localization method and Gabor feature vectors like
EBGM.
Abstract: The purpose of this study is to present a non invasive
method for the marginal adaptation evaluation in class V composite
restorations. Standardized class V cavities, prepared in human
extracted teeth, were filled with Premise (Kerr) composite. The
specimens were thermo cycled. The interfaces were examined by
Optical Coherence Tomography method (OCT) combined with the
confocal microscopy and fluorescence. The optical configuration
uses two single mode directional couplers with a superluminiscent
diode as the source at 1300 nm. The scanning procedure is similar to
that used in any confocal microscope, where the fast scanning is enface
(line rate) and the depth scanning is much slower (at the frame
rate). Gaps at the interfaces as well as inside the composite resin
materials were identified. OCT has numerous advantages which
justify its use in vivo as well as in vitro in comparison with
conventional techniques.
Abstract: Corporate credit rating prediction using statistical and
artificial intelligence (AI) techniques has been one of the attractive
research topics in the literature. In recent years, multiclass
classification models such as artificial neural network (ANN) or
multiclass support vector machine (MSVM) have become a very
appealing machine learning approaches due to their good
performance. However, most of them have only focused on classifying
samples into nominal categories, thus the unique characteristic of the
credit rating - ordinality - has been seldom considered in their
approaches. This study proposes new types of ANN and MSVM
classifiers, which are named OMANN and OMSVM respectively.
OMANN and OMSVM are designed to extend binary ANN or SVM
classifiers by applying ordinal pairwise partitioning (OPP) strategy.
These models can handle ordinal multiple classes efficiently and
effectively. To validate the usefulness of these two models, we applied
them to the real-world bond rating case. We compared the results of
our models to those of conventional approaches. The experimental
results showed that our proposed models improve classification
accuracy in comparison to typical multiclass classification techniques
with the reduced computation resource.