Abstract: Cogeneration may be defined as a system which
contains electricity production and regain of the thermo value of
exhaust gases simultaneously. The examination is based on the data-s
of an active cogeneration plant. This study, it is aimed to determine
which component of the system should be revised first to raise the
efficiency and decrease the loss of exergy. For this purpose, second
law analysis of thermodynamics is applied to each component due to
consider the effects of environmental conditions and take the quality
of energy into consideration as well as the quantity of it. The exergy
balance equations are produced and exergy loss is calculated for each
component. 44,44 % loss of exergy in heat exchanger, 29,59 % in
combustion chamber, 18,68 % in steam boiler, 5,25 % in gas turbine
and 2,03 % in compressor is calculated.
Abstract: The paper investigates parallel channel instabilities of
natural circulation boiling water reactor. A thermal-hydraulic model
is developed to simulate two-phase flow behavior in the natural circulation boiling water reactor (NCBWR) with the incorporation of
ex-core components and recirculation loop such as steam separator, down-comer, lower-horizontal section and upper-horizontal section
and then, numerical analysis is carried out for parallel channel
instabilities of the reactor undergoing both in-phase and out-of-phase
modes of oscillations. To analyze the relative effect on stability of the reactor due to inclusion of various ex-core components and
recirculation loop, marginal stable point is obtained at a particular inlet enthalpy of the reactor core without the inclusion of ex-core
components and recirculation loop and then with the inclusion of the
same. Numerical simulations are also conducted to determine the
relative dominance between two modes of oscillations i.e. in-phase and out-of-phase. Simulations are also carried out when the channels
are subjected to asymmetric power distribution keeping the inlet enthalpy same.
Abstract: Thermal-driven refrigeration systems have attracted increasing research and development interest in recent years. These systems do not cause ozone depletion and can reduce demand on electricity. The main objective of this work is to perform theoretical analyses of a thermal-driven refrigeration system using a new sorbent-sorptive pair as the working pair. The active component of sorbent is sodium thiocyanate (NaSCN). Ammonia (NH3) is chosen as sorptive. Based on the thermodynamic properties of the working solution, a mathematical model is introduced to analyze the system characteristics and performance. The results are used to compare with other thermal-driven refrigeration systems. It is shown that the advantages provided by this system over other absorption units include lower generator and evaporator temperatures, a higher coefficient of performance (COP). The COP is about 10 percent higher than the ones for the NH3-H2O system working at the same conditions.
Abstract: Building inspection is one of the key components of building maintenance. The primary purpose of performing a building inspection is to evaluate the building-s condition. Without inspection, it is difficult to determine a built asset-s current condition, so failure to inspect can contribute to the asset-s future failure. Traditionally, a longhand survey description has been widely used for property condition reports. Surveys that employ ratings instead of descriptions are gaining wide acceptance in the industry because they cater to the need for numerical analysis output. These kinds of surveys are also in keeping with the new RICS HomeBuyer Report 2009. In this paper, we propose a new assessment method, derived from the current rating systems, for assessing the specifically smart school building-s condition and rating the seriousness of each defect identified. These two assessment criteria are then multiplied to find the building-s score, which we called the Condition Survey Protocol (CSP) 1 Matrix. Instead of a longhand description of a building-s defects, this matrix requires concise explanations about the defects identified, thus saving on-site time during a smart school building inspection. The full score is used to give the building an overall rating: Good, Fair or Dilapidated.
Abstract: Wheat germ has a balanced amino acid composition of the protein, which is well digested by enzymes in the gastrointestinal tract of humans, a high content of vitamins, minerals and unsaturated acids. Introduction components grain food products will enrich their biologically important substances, giving these products a number of valuable properties and reducing their caloric.
A complex natural system of substances in foods will help replenish the body's need of essential nutrients, increasing its resistance to the harmful effects of the environment, prolong life. In this regard, there was a need for the development of production technology of protein complexes from wheat germ and then applying them in food, particularly in the dairy industry. Experimental studies were conducted to determine the number of herbal supplements on the sensory characteristics of the product. Studies have been conducted to determine the optimal process parameters of water activity and moisture content of the investigational product.
Abstract: Online discussions are an important component of
both blended and online courses. This paper examines the varieties of
online discussions and the perils, pitfalls and possibilities of this
rather new technological tool for enhanced learning. The discussion
begins with possible perils and pitfalls inherent in this educational
tool and moves to a consideration of the advantages of the varieties
of online discussions feasible for use in teacher education programs.
Abstract: This paper proposes rough set models with three
different level knowledge granules in incomplete information system
under tolerance relation by similarity between objects according to
their attribute values. Through introducing dominance relation on the
discourse to decompose similarity classes into three subclasses: little
better subclass, little worse subclass and vague subclass, it dismantles
lower and upper approximations into three components. By using
these components, retrieving information to find naturally hierarchical
expansions to queries and constructing answers to elaborative queries
can be effective. It illustrates the approach in applying rough set
models in the design of information retrieval system to access different
granular expanded documents. The proposed method enhances rough
set model application in the flexibility of expansions and elaborative
queries in information retrieval.
Abstract: The flow field within the combustor of scramjet
engine is very complex and poses a considerable challenge in the
design and development of a supersonic combustor with an optimized
geometry. In this paper comprehensive numerical studies on flow
field characteristics of different cavity based scramjet combustors
with transverse injection of hydrogen have been carried out for both
non-reacting and reacting flows. The numerical studies have been
carried out using a validated 2D unsteady, density based 1st-order
implicit k-omega turbulence model with multi-component finite rate
reacting species. The results show a wide variety of flow features
resulting from the interactions between the injector flows, shock
waves, boundary layers, and cavity flows. We conjectured that an
optimized cavity is a good choice to stabilize the flame in the
hypersonic flow, and it generates a recirculation zone in the scramjet
combustor. We comprehended that the cavity based scramjet
combustors having a bearing on the source of disturbance for the
transverse jet oscillation, fuel/air mixing enhancement, and flameholding
improvement. We concluded that cavity shape with
backward facing step and 45o forward ramp is a good choice to get
higher temperatures at the exit compared to other four models of
scramjet combustors considered in this study.
Abstract: Fuzzy Cognitive Maps (FCMs) is a causal graph, which shows the relations between essential components in complex systems. Experts who are familiar with the system components and their relations can generate a related FCM. There is a big gap when human experts cannot produce FCM or even there is no expert to produce the related FCM. Therefore, a new mechanism must be used to bridge this gap. In this paper, a novel learning method is proposed to construct causal graph based on historical data and by using metaheuristic such Tabu Search (TS). The efficiency of the proposed method is shown via comparison of its results of some numerical examples with those of some other methods.
Abstract: A multimedia presentation system refers to the integration of a multimedia database with a presentation manager which has the functionality of content selection, organization and playout of multimedia presentations. It requires high performance of involved system components. Starting from multimedia information capture until the presentation delivery, high performance tools are required for accessing, manipulating, storing and retrieving these segments, for transferring and delivering them in a presentation terminal according to a playout order. The organization of presentations is a complex task in that the display order of presentation contents (in time and space) must be specified. A multimedia presentation contains audio, video, images and text media types. The critical decisions for presentation construction include what the contents are, how the contents are organized, and once the decision is made on the organization of the contents of the presentation, it must be conveyed to the end user in the correct organizational order and in a timely fashion. This paper introduces a framework for specification of multimedia presentations and describes the design of sample presentations using this framework from a multimedia database.
Abstract: Numerical analysis of flow characteristics and
separation efficiency in a high-efficiency cyclone has been performed.
Several models based on the experimental observation for a design
purpose were proposed. However, the model is only estimated the
cyclone's performance under the limited environments; it is difficult to
obtain a general model for all types of cyclones. The purpose of this
study is to find out the flow characteristics and separation efficiency
numerically. The Reynolds stress model (RSM) was employed instead
of a standard k-ε or a k-ω model which was suitable for isotropic
turbulence and it could predict the pressure drop and the Rankine
vortex very well. For small particles, there were three significant
components (entrance of vortex finder, cone, and dust collector) for
the particle separation. In the present work, the particle re-entraining
phenomenon from the dust collector to the cyclone body was observed
after considerable time. This re-entrainment degraded the separation
efficiency and was one of the significant factors for the separation
efficiency of the cyclone.
Abstract: Advertising today has already become an integral part
of human life as a building block of the consumer community. A
component of the value chain of the media, advertising sector is
struggling increasingly harder to find new methods to reach
consumers. The tendency towards experimental marketing practices
is increasing day by day, especially to divert consumers from the idea
“They are selling something to me.” It is therefore considered a good
idea to investigate the trust in ad media of consumers, who are today
exposed to a great bulk of information from advertising sector.
In this study, the current value of ad media for the young
consumer will be investigated. Data on various ad media reliability
will be comparatively analyzed and young consumers will be traced
by including university students in the study. In this research, which
will be performed on students studying at the Selçuk University
(Turkey) by random sampling method, data will be obtained by
survey technique and evaluated by a statistical analysis.
Abstract: Al-Murabahah is an Islamic financing facility used in
asset financing, the profit rate of the contract is determined by
components which are also being used in the conventional banking.
Such are cost of fund, overhead cost, risk premium cost and bank-s
profit margin. At the same time, the profit rate determined by Islamic
banking system also refers to Inter-Bank Offered Rate (LIBOR) in
London as a benchmark. This practice has risen arguments among
Muslim scholars in term of its validity of the contract; whether the
contract maintains the Shariah compliance or not. This paper aims to
explore the view of Shariah towards the above components practiced
by Islamic Banking in determining the profit rate of al-murabahah
asset financing in Malaysia. This is a comparative research which
applied the views of Muslim scholars from all major mazahibs in
Islamic jurisprudence and examined the practices by Islamic banks in
Malaysia for the above components. The study found that the shariah
accepts all the components with conditions. The cost of fund is
accepted as a portion of al-mudarabah-s profit, the overhead cost is
accepted as a cost of product, risk premium cost consist of business
risk and mitigation risk are accepted through the concept of alta-awun
and bank-s profit margin is accepted as a right of bank after
venturing in risky investment.
Abstract: Sowing date and density are two important factors in
produce of coriander. A field experiment was conducted with
treatments: sowing time (5 May, 20 May, 4 June and 19 June 2009)
and plant density (10, 30, 50 and 70 plants m-2). The experimental
plots were laid out in a factorial according to a RCBD with three
replications. Results showed that the effect of sowing dates and
densities were significant on grain yield and yield components, but
interaction effects between sowing time and density were non
significant for all of traits in this trial. At sowing times 5 May, 20
May, 4 June and 19 June, grain yield obtained 736.9, 837.8, 1003.1
and 1299.6 kg ha-1, respectively. At 10, 30, 50 and 70 plants m-2,
grain yield were 794.9, 1031.0, 1092.3 and 959.3 kg ha-1,
respectively. In this experiment, sowing at 19 June and 50 and 30
plants m-2 had the most grain yield.
Abstract: In the context of spectrum surveillance, a new method
to recover the code of spread spectrum signal is presented, while the
receiver has no knowledge of the transmitter-s spreading sequence. In
our previous paper, we used Genetic algorithm (GA), to recover
spreading code. Although genetic algorithms (GAs) are well known
for their robustness in solving complex optimization problems, but
nonetheless, by increasing the length of the code, we will often lead
to an unacceptable slow convergence speed. To solve this problem we
introduce Particle Swarm Optimization (PSO) into code estimation in
spread spectrum communication system. In searching process for
code estimation, the PSO algorithm has the merits of rapid
convergence to the global optimum, without being trapped in local
suboptimum, and good robustness to noise. In this paper we describe
how to implement PSO as a component of a searching algorithm in
code estimation. Swarm intelligence boasts a number of advantages
due to the use of mobile agents. Some of them are: Scalability, Fault
tolerance, Adaptation, Speed, Modularity, Autonomy, and
Parallelism. These properties make swarm intelligence very attractive
for spread spectrum code estimation. They also make swarm
intelligence suitable for a variety of other kinds of channels. Our
results compare between swarm-based algorithms and Genetic
algorithms, and also show PSO algorithm performance in code
estimation process.
Abstract: This paper presents an architecture to assist in the
development of tools to perform experimental analysis. Existing
implementations of tools based on this architecture are also described
in this paper. These tools are applied to the real world problem of
fault attack emulation and detection in cryptographic algorithms.
Abstract: This paper presents an integrated case based and rule
based reasoning method for car faulty diagnosis. The reasoning
method is done through extracting the past cases from the Proton
Service Center while comparing with the preset rules to deduce a
diagnosis/solution to a car service case. New cases will be stored to
the knowledge base. The test cases examples illustrate the
effectiveness of the proposed integrated reasoning. It has proven
accuracy of similar reasoning if carried out by a service advisor from
the service center.
Abstract: This paper focuses on a critical component of the situational awareness (SA), the neural control of autonomous constant depth flight of an autonomous underwater vehicle (AUV). Autonomous constant depth flight is a challenging but important task for AUVs to achieve high level of autonomy under adverse conditions. The fundamental requirement for constant depth flight is the knowledge of the depth, and a properly designed controller to govern the process. The AUV, named VORAM, is used as a model for the verification of the proposed hybrid control algorithm. Three neural network controllers, named NARMA-L2 controllers, are designed for fast and stable diving maneuvers of chosen AUV model. This hybrid control strategy for chosen AUV model has been verified by simulation of diving maneuvers using software package Simulink and demonstrated good performance for fast SA in real-time searchand- rescue operations.
Abstract: Recently, Denial of Service(DoS) attacks and Distributed DoS(DDoS) attacks which are stronger form of DoS attacks from plural hosts have become security threats on the Internet. It is important to identify the attack source and to block attack traffic as one of the measures against these attacks. In general, it is difficult to identify them because information about the attack source is falsified. Therefore a method of identifying the attack source by tracing the route of the attack traffic is necessary. A traceback method which uses traffic patterns, using changes in the number of packets over time as criteria for the attack traceback has been proposed. The traceback method using the traffic patterns can trace the attack by matching the shapes of input traffic patterns and the shape of output traffic pattern observed at a network branch point such as a router. The traffic pattern is a shapes of traffic and unfalsifiable information. The proposed trace methods proposed till date cannot obtain enough tracing accuracy, because they directly use traffic patterns which are influenced by non-attack traffics. In this paper, a new traffic pattern matching method using Independent Component Analysis(ICA) is proposed.
Abstract: The main aims in this research are to study the solid
waste generation in the Faculty of Engineering and Built
Environment in the UKM and at the same time to determine
composition and some of the waste characteristics likewise: moisture
content, density, pH and C/N ratio. For this purpose multiple
campaigns were conducted to collect the wastes produced in all
hostels, faculties, offices and so on, during 24th of February till 2nd
of March 2009, measure and investigate them with regard to both
physical and chemical characteristics leading to highlight the
necessary management policies. Research locations are Faculty of
Engineering and the Canteen nearby that. From the result gained, the
most suitable solid waste management solution will be proposed to
UKM. The average solid waste generation rate in UKM is 203.38
kg/day. The composition of solid waste generated are glass, plastic,
metal, aluminum, organic and inorganic waste and others waste.
From the laboratory result, the average moisture content, density, pH
and C/N ratio values from the solid waste generated are 49.74%,
165.1 kg/m3, 5.3, and 7:1 respectively. Since, the food waste (organic
waste) were the most dominant component, around 62% from the
total waste generated hence, the most suitable solid waste
management solution is composting.