Abstract: Recent developments in information and
communication technologies (ICT) have created excellent conditions
for profoundly enhancing the traditional learning and teaching
practices. New modes of teaching in higher education subjects can
profoundly enhance ones ability to proactively constructing his or her
personal learning universe. These developments have contributed to
digital learning environments becoming widely available and
accessible. In addition, there is a trend towards enlargement and
specialization in higher education in Europe. With as a result that
existing Master of Science (MSc) programmes are merged or new
programmes have been established that are offered as joint MSc
programmes to students. In these joint MSc programmes, the need for
(common) digital learning environments capable of surmounting the
barriers of time and location has become evident. This paper
discusses the past and ongoing efforts to establish such common
digital learning environments in two joint MSc programmes in
Europe and discusses the way technology-based learning
environments affect the traditional way of learning.
Abstract: Size based filtration is one of the common methods
employed to isolate circulating tumor cells (CTCs) from whole
blood. It is well known that this method suffers from isolation
efficiency to purity tradeoff. However, this tradeoff is poorly
understood. In this paper, we present the design and manufacturing
of a special rectangular slit filter. The filter was designed to retain
maximal amounts of nucleated cells, while minimizing the pressure
on cells, thereby preserving their morphology. The key parameter,
namely, input pressure, was optimized to retain the maximal number
of tumor cells, whilst maximizing the depletion of normal blood cells
(red and white blood cells and platelets). Our results indicate that for
a slit geometry of 5 × 40 μm on a 13 mm circular membrane with a
fill factor of 21%, a pressure of 6.9 mBar yields the optimum for
maximizing isolation of MCF-7 and depletion of normal blood cells.
Abstract: The proof of concept experiments were conducted to
determine the feasibility of using small amounts of Dissolved
Sulphur (DS) from the gaseous phase to precipitate platinum ions in
chloride media. Two sets of precipitation experiments were
performed in which the source of sulphur atoms was either a
thiosulphate solution (Na2S2O3) or a sulphur dioxide gas (SO2). In
liquid-liquid (L-L) system, complete precipitation of Pt was achieved
at small dosages of Na2S2O3 (0.01 – 1.0 M) in a time interval of 3-5
minutes. On the basis of this result, gas absorption tests were carried
out mainly to achieve sulphur solubility equivalent to 0.018 M. The
idea that huge amounts of precious metals could be recovered
selectively from their dilute solutions by utilizing the waste SO2
streams at low pressure seemed attractive from the economic and
environmental point of views. Therefore, mass transfer characteristics
of SO2 gas associated with reactive absorption across the gas-liquid
(G-L) interface were evaluated under different conditions of pressure
(0.5 – 2 bar), solution temperature ranges from 20 – 50 oC and acid
strength (1 – 4 M, HCl). This paper concludes with information about
selective precipitation of Pt in the presence of cations (Fe2+, Co2+,
and Cr3+) in a CSTR and recommendation to scale up laboratory data
to industrial pilot scale operations.
Abstract: In this article a bibliography research takes place to
track down and introduce the barriers and opportunities for the
adoption of e-Governance services mainly from the side of citizen,
that is to say, the demand side. Although governments invest
continuously in producing of e-Governance services, citizens face
difficulties to adopt these services. Barriers derive and prevent them
from using e-Governance services. Barrier is anything preventing
citizens from the adoption of e-Governance services. Barriers impede
or do not allow the adoption of e-Governance services by the
citizens. If the barriers are pinpointed, it will be possible to take them
into consideration while designing e-Governance services which the
citizens are likely to use, if the obstacles are raised. The barriers will
thus be converted in opportunities that will facilitate the adoption.
Abstract: Background Contact lens (CL) wear can cause
changes in blinking and corneal staining. Aims and Objectives To
determine the effects of CL materials (HEMA and SiHy) on
spontaneous blink rate, blinking patterns and corneal staining after 2
months of wear. Methods Ninety subjects in 3 groups (control,
HEMA and SiHy) were assessed at baseline and 2-months. Blink rate
was recorded using a video camera. Blinking patterns were assessed
with digital camera and slit lamp biomicroscope. Corneal staining
was graded using IER grading scale Results There were no significant
differences in all parameters at baseline. At 2 months, CL wearers
showed significant increment in average blink rate (F1.626, 47.141 =
7.250, p = 0.003; F2,58 = 6.240, p = 0.004) and corneal staining (χ2
2,
n=30 = 31.921, p < 0.001; χ2
2, n=30 = 26.909, p < 0.001). Conclusion
Blinking characteristics and corneal staining were not influence by
soft CL materials.
Abstract: Practices of food sharing as part of the brotherhood and hospitality interpretation have been essential part of the Kazakh ethnic culture since early times. Dialogue in time and space between Kazakhs through differences in food interpretation among the ethnic repatriates may become a link connecting them and platform for stable relations with the host society or serious barrier on the way of their integration in the Kazakhstani society. The article elucidates by the field materials how some aspects of food culture differences among ethnic Kazakhs living abroad (XUAR of China) and ethnic repatriates in Kazakhstan may influence their integration path.
Abstract: Recent scientific investigations indicate that
multimodal biometrics overcome the technical limitations of
unimodal biometrics, making them ideally suited for everyday life
applications that require a reliable authentication system. However,
for a successful adoption of multimodal biometrics, such systems
would require large heterogeneous datasets with complex multimodal
fusion and privacy schemes spanning various distributed
environments. From experimental investigations of current
multimodal systems, this paper reports the various issues related to
speed, error-recovery and privacy that impede the diffusion of such
systems in real-life. This calls for a robust mechanism that caters to
the desired real-time performance, robust fusion schemes,
interoperability and adaptable privacy policies.
The main objective of this paper is to present a framework that
addresses the abovementioned issues by leveraging on the
heterogeneous resource sharing capacities of Grid services and the
efficient machine learning capabilities of artificial neural networks
(ANN). Hence, this paper proposes a Grid-based neural network
framework for adopting multimodal biometrics with the view of
overcoming the barriers of performance, privacy and risk issues that
are associated with shared heterogeneous multimodal data centres.
The framework combines the concept of Grid services for reliable
brokering and privacy policy management of shared biometric
resources along with a momentum back propagation ANN (MBPANN)
model of machine learning for efficient multimodal fusion and
authentication schemes. Real-life applications would be able to adopt
the proposed framework to cater to the varying business requirements
and user privacies for a successful diffusion of multimodal
biometrics in various day-to-day transactions.
Abstract: Gluconic acid is one of interesting chemical products
in industries such as detergents, leather, photographic, textile, and
especially in food and pharmaceutical industries. Fermentation is an
advantageous process to produce gluconic acid. Mathematical
modeling is important in the design and operation of fermentation
process. In fact, kinetic data must be available for modeling. The
kinetic parameters of gluconic acid production by Aspergillus niger
in batch culture was studied in this research at initial substrate
concentration of 150, 200 and 250 g/l. The kinetic models used were
logistic equation for growth, Luedeking-Piret equation for gluconic
acid formation, and Luedeking-Piret-like equation for glucose
consumption. The Kinetic parameters in the model were obtained by
minimizing non linear least squares curve fitting.
Abstract: Measurements of radioactivity in the environment is of great importance to monitor and control the levels of radiation to which man is exposed directly or indirectly. It is necessary to show that regardless of working or being close to nuclear power plants, people are daily in contact with some amount of radiation from the actual environment and food that are ingested, contradicting the view of most of them. The aim of this study was to analyze the rate of natural and artificial radiation from radionuclides present in cement, soil and fertilizers used in Sergipe State – Brazil. The radionuclide activitiesmeasured all samples arebelow the Brazilian limit of the exclusion and exemption criteria from the requirement of radiation protection.It was detected Be-7 in organic fertilizers that means a short interval between the brewing processes for use in agriculture. It was also detected an unexpected Cs-137 in some samples; however its activities does not represent risk for the population. Th-231 was also found in samples of soil and cement in the state of Sergipe that is an unprecedented result.
Abstract: In this paper, a novel method for a biometric system based on the ECG signal is proposed, using spectral coefficients computed through linear predictive coding (LPC). ECG biometric systems have traditionally incorporated characteristics of fiducial points of the ECG signal as the feature set. These systems have been shown to contain loopholes and thus a non-fiducial system allows for tighter security. In the proposed system, incorporating non-fiducial features from the LPC spectrum produced a segment and subject recognition rate of 99.52% and 100% respectively. The recognition rates outperformed the biometric system that is based on the wavelet packet decomposition (WPD) algorithm in terms of recognition rates and computation time. This allows for LPC to be used in a practical ECG biometric system that requires fast, stringent and accurate recognition.
Abstract: A code has been developed in Mathematica using
Direct Simulation Monte Carlo (DSMC) technique. The code was
tested for 2-D air flow around a circular cylinder. Same geometry
and flow properties were used in FLUENT 6.2 for comparison. The
results obtained from Mathematica simulation indicated significant
agreement with FLUENT calculations, hence providing insight into
particle nature of fluid flows.
Abstract: Some theoretical and experimental aspects related to
the conceptual analyses concerning the direct correspondence
identification between the shape, area and orientation of plantar
pressure and obtaining adequate corrective insoles by rapid
prototyping are presented in this paper. In the first part of the paper
there is the theoretical-correlative concept, which is the fundament of
correspondence deduction between plantar surface characteristics and
respectively corrective insoles. In the second part of the paper the
experimental equipment used to analyze and perform the
correspondence stages and then the integral ones between the
analyzed foot shapes and the ones with corrective insoles is
presented. In the final parte the results used to adapt the insoles
obtained by rapid prototyping but also some specific aspects and
conclusions of the conceptual analysis of direct and rapid
correspondence are shown.
Abstract: This paper presents a microstrip meandered open
circuited stub with bandstop characteristic. The proposed structure is
designed on a high frequency laminate with dielectric constant of 4.0
and board thickness of 0.508 millimeters. The scattering parameters
and electromagnetic field distributions at various frequencies are
investigated by modeling the structure with three dimensional
electromagnetic simulation tool. In order to describe the resonant
and bandstop characteristic of the meandered open circuited stub, a
Smith chart as well as electric field at various frequencies and phases
is illustrated accordingly. The structure can be an alternative method
in suppressing the harmonic response of a bandpass filter.
Abstract: The development of the power electronics has allowed
increasing the precision and reliability of the electrical devices, thanks
to the adjustable inverters, as the Pulse Wide Modulation (PWM)
applied to the three level inverters, which is the object of this study.
The authors treat the relation between the law order adopted for a
given system and the oscillations of the electrical and mechanical
parameters of which the tolerance depends on the process with which
they are integrated (paper factory, lifting of the heavy loads,
etc.).Thus, the best choice of the regulation indexes allows us to
achieve stability and safety training without investment (management
of existing equipment). The optimal behavior of any electric device
can be achieved by the minimization of the stored electrical and
mechanical energy.
Abstract: Hardness of the widely used structural steel is of vital
importance since it may help in the determination of many
mechanical properties of a material under loading situations. In order
to obtain reliable information for design, properties homogeneity
should be validated. In the current study the hardness variation over
the different diameters of the same AISI 4140 bar is investigated.
Measurements were taken on the two faces of the stock at equally
spaced eight sectors and fifteen layers. Statistical and graphical
analysis are performed to asses the distribution of hardness
measurements over the specified area. Hardness measurements
showed some degree of dispersion with about ± 10% of its nominal
value provided by manufacturer. Hardness value is found to have a
slight decrease trend as the diameter is reduced. However, an
opposite behavior is noticed regarding the sequence of the sector
indicating a nonuniform distribution over the same area either on the
same face or considering the corresponding sector on the other face
(cross section) of the same material bar.
Abstract: Travelling salesman problem (TSP) is a combinational
optimization problem and solution approaches have been applied
many real world problems. Pure TSP assumes the cities to visit are
fixed in time and thus solutions are created to find shortest path
according to these point. But some of the points are canceled to visit
in time. If the problem is not time crucial it is not important to
determine new routing plan but if the points are changing rapidly and
time is necessary do decide a new route plan a new approach should
be applied in such cases. We developed a route plan transfer method
based on transfer learning and we achieved high performance against
determining a new model from scratch in every change.
Abstract: Waste management is now a global concern due to its
high environmental impact on climate change. Because of generating
huge amount of waste through our daily activities, managing waste in
an efficient way has become more important than ever. Alternative
Waste Technology (AWT), a new category of waste treatment
technology has been developed for energy recovery in recent years to
address this issue. AWT describes a technology that redirects waste
away from landfill, recovers more useable resources from the waste
flow and reduces the impact on the surroundings. Australia is one of
the largest producers of waste per-capita. A number of AWTs are
using in Australia to produce energy from waste. Presently, it is vital
to identify an appropriate AWT to establish a sustainable waste
management system in Australia. Identification of an appropriate
AWT through Multi-criteria analysis (MCA) of four AWTs by using
five key decision making criteria is presented and discussed in this
paper.
Abstract: –In this paper the damage in clamped-free, clampedclamped and free-free beam are analyzed considering samples
without and with structural modifications. The damage location is
investigated by the use of the bispectrum and wavelet analysis. The
mathematical models are obtained using 2D elasticity theory and the
Finite Element Method (FEM). The numerical and experimental data
are approximated using the Particle Swarm Optimizer (PSO) method
and this way is possible to adjust the localization and the severity of
the damage. The experimental data are obtained through
accelerometers placed along the sample. The system is excited using
impact hammer.
Abstract: Wall-surface jet induced by the dielectric barrier
discharge (DBD) has been proposed as an actuator for active flow
control in aerodynamic applications. Discharge plasma evolution of
the DBD plasma actuator was simulated based on a simple fluid model,
in which the electron, one type of positive ion and negative ion were
taken into account. Two-dimensional simulation was conducted, and
the results are in agreement with the insights obtained from
experimental studies. The simulation results indicate that the discharge
mode changes depending on applied voltage slope; when the applied
voltage is positive-going with high applied voltage slope, the
corona-type discharge mode turns into the streamer-type discharge
mode and the threshold voltage slope is around 300 kV/ms in this
simulation. The characteristics of the electrohydrodynamic (EHD)
force, which is the source of the wall-surface jet, also change
depending on the discharge mode; the tentative peak value of the EHD
force during the positive-going voltage phase is saturated by the
periodical formation of the streamer-type discharge.
Abstract: In studying the possibility of using plants as
rhizoremediators, barley and grass mixture which showed resistance
to various concentrations of oil were selected. The minimum
inhibitory effect of oil on these plants by morphological parameters
such as survival of plants, length and biomass of shoot and root
compared with the control was showed. In determining physiological
parameters, a slight decrease in the number of chlorophyll a and b in
the leaves of plants was noted. The differences in the ratio of the total
surface of the roots to the work surface with the growth of plants in
soil with oil in the study of adsorption of the root surface were
showed.