Abstract: This paper aims to select the optimal location and
setting parameters of TCSC (Thyristor Controlled Series
Compensator) controller using Particle Swarm Optimization (PSO)
and Genetic Algorithm (GA) to mitigate small signal oscillations in a
multimachine power system. Though Power System Stabilizers
(PSSs) are prime choice in this issue, installation of FACTS device
has been suggested here in order to achieve appreciable damping of
system oscillations. However, performance of any FACTS devices
highly depends upon its parameters and suitable location in the
power network. In this paper PSO as well as GA based techniques are
used separately and compared their performances to investigate this
problem. The results of small signal stability analysis have been
represented employing eigenvalue as well as time domain response in
face of two common power system disturbances e.g., varying load
and transmission line outage. It has been revealed that the PSO based
TCSC controller is more effective than GA based controller even
during critical loading condition.
Abstract: A generalization of the concepts of Feistel Networks (FN), known as Extended Feistel Network (EFN) is examined. EFN splits the input blocks into n > 2 sub-blocks. Like conventional FN, EFN consists of a series of rounds whereby at least one sub-block is subjected to an F function. The function plays a key role in the diffusion process due to its completeness property. It is also important to note that in EFN the F-function is the most computationally expensive operation in a round. The aim of this paper is to determine a suitable type of EFN for a scalable cipher. This is done by analyzing the threshold number of rounds for different types of EFN to achieve the completeness property as well as the number of F-function required in the network. The work focuses on EFN-Type I, Type II and Type III only. In the analysis it is found that EFN-Type II and Type III diffuses at the same rate and both are faster than Type-I EFN. Since EFN-Type-II uses less F functions as compared to EFN-Type III, therefore Type II is the most suitable EFN for use in a scalable cipher.
Abstract: The aim of this study was to estimate the frequency of
EBV infection in Hodgkin's lymphoma (HL) and non-Hodgkin's
lymphoma (NHL) occurring in Jordanian patients. A total of 55
patients with lymphoma were examined in this study. Of 55 patients,
30 and 25 were diagnosed as HL and NHL, respectively. The four
HL subtypes were observed with the majority of the cases exhibited
the mixed cellularity (MC) subtype followed by the nodular sclerosis
(NS). The high grade was found to be the commonest subtype of
NHL in our sample, followed by the low grade. The presence of EBV
virus was detected by immunostating for expression of latent
membrane protein-1 (LMP-1). The frequency of LMP-1 expression
occurred more frequent in patients with HL (60.0%) than in patients
with NHL (32.0%). The frequency of LMP-1 expression was also
higher in patients with MC subtype (61.11%) than those patients with
NS (28.57%). No age or gender difference in occurrence of EBV
infection was observed among patient with HL. By contrast, the
prevalence of EBV infection in NHL patients aged below 50 was
lower (16.66%) than in NHL patients aged 50 or above (46.15%). In
addition, EBV infection was more frequent in females with NHL
(38.46%) than in male with NHL (25%). In NHL cases, the
frequency of EBV infection in intermediate grade (60.0%) was high
when compared with frequency of low (25%) or high grades (25%).
In conclusion, analysis of LMP-1 expression indicates an important
role for this viral oncogene in the pathogenesis of EBV-associated
malignant lymphomas. These data also support the previous findings
that people with EBV may develop lymphoma and that efforts to
maintain low lymphoma should be considered for people with EBV
infection.
Abstract: Advances in technology (e.g. the internet,
telecommunication) and political changes (fewer trade barriers and an
enlarged European Union, ASEAN, NAFTA and other organizations)
have led to develop international competition and expand into new
markets. Companies in Thailand, Asia and around the globe are
increasingly being pressured on price and for faster time to enter the
market. At the same time, new markets are appearing and many
companies are looking for changes and shifts in their domestic
markets. These factors have enabled the rapid growth for companies
and globalizing many different business activities during the product
development process from research and development (R&D) to
production.
This research will show and clarify methods how to develop
global product. Also, it will show how important is a global product
impact into Thai Economy development.
Abstract: The paper deals with the effect of ion nitriding and
carbonitriding on fatigue strength of steel parts under the fretting
conditions. Instrumented fatigue tests were carried out on surface
treated flat bars from EA1N and EA4T steels with different strength.
The chosen surfacing decrease importantly an unfavorable fretting
effect. Nitridation suppressed the unfavorable effect of fretting
almost entirely, while the influence of carbonitridation was less
striking. The results were compared with those ones obtained on bars
without surfacing. The causes of favorable influence of surfacing are
discussed.
Abstract: Solar shading designs are important for reduction of building energy consumption and improvement of indoor thermal environment. This paper carried out a number of building simulations for evaluation of the energy performance of different shading devices based on incremental costs. The results show that movable shading devices lower incremental costs by up to 50% compared with fixed ones for the same building energy efficiency for residential buildings, and wing panel shadings are much more suitable in commercial buildings than baring screen ones and overhangs for commercial buildings.
Abstract: This paper proposes an architectural and graphical
user interface (GUI) design of a traditional Thai musical instrument
application for tablet computers for practicing “Ranaad Ek" which is
a trough-resonated keyboard percussion instrument. The application
provides percussion methods for a player as real as a physical
instrument. The application consists of two playing modes. The first
mode is free playing, a player can freely multi touches on wooden bar
to produce instrument sounds. The second mode is practicing mode
that guilds the player to follow percussions and rhythms of practice
songs. The application has achieved requirements and specifications.
Abstract: In this paper we canvass three case studies of unique
research partnerships between universities and schools in the wider
community. In doing so, we consider those areas of indeterminate
zones of professional practice explored by academics in their
research activities within the wider community. We discuss three
cases: an artist-in-residence program designed to engage primary
school children with new understandings about local Indigenous
Australian issues in their pedagogical and physical landscapes; an
assessment of pedagogical concerns in relation to the use of physical
space in classrooms; and the pedagogical underpinnings of a
costumed museum school program. In doing so, we engage issues of
research as playing an integral part in the development,
implementation and maintenance of academic engagements with
wider community issues.
Abstract: The goal of admission control is to support the Quality
of Service demands of real-time applications via resource reservation
in IP networks. In this paper we introduce a novel Dynamic
Admission Control (DAC) mechanism for IP networks. The DAC
dynamically allocates network resources using the previous network
pattern for each path and uses the dynamic admission algorithm to
improve bandwidth utilization using bandwidth brokers. We evaluate
the performance of the proposed mechanism through trace-driven
simulation experiments in view point of blocking probability,
throughput and normalized utilization.
Abstract: In this paper a novel algorithm is proposed to merit
the accuracy of finger vein recognition. The performances of
Principal Component Analysis (PCA), Kernel Principal Component
Analysis (KPCA), and Kernel Entropy Component Analysis (KECA)
in this algorithm are validated and compared with each other in order
to determine which one is the most appropriate one in terms of finger
vein recognition.
Abstract: Measurements of capacitance C and dissipation
factor tand of the stator insulation system provide useful information
about internal defects within the insulation. The index k is defined as
the proportionality constant between the changes at high voltage of
capacitance DC and of the dissipation factor Dtand . DC and
Dtand values were highly correlated when small flat defects were
within the insulation and that correlation was lost in the presence of
large narrow defects like electrical treeing. The discrimination
between small and large defects is made resorting to partial discharge
PD phase angle analysis. For the validation of the results, C and tand
measurements were carried out in a 15MVA 4160V steam turbine
turbogenerator placed in a sugar mill. In addition, laboratory test
results obtained by other authors were analyzed jointly. In such
laboratory tests, model coil bars subjected to thermal cycling resulted
highly degraded and DC and Dtand values were not correlated. Thus,
the index k could not be calculated.
Abstract: After the development of the Internet a suitable
discipline for trading goods electronically has been emerged.
However, this type of markets is not still mature enough in order to
become independent and get closer to seller/buyer-s needs.
Furthermore, the buyable and sellable goods in these markets still
don-t have essential standards for being well-defined. In this paper,
we will present a model for development of a market which can
contain goods with variable definitions and we will also investigate
its characteristics. Besides, by noticing the fact that people have
different discriminations, it-s figured out that the significance of each
attribute of a specific product may vary from different people-s view
points. Consequently we-ll present a model for weighting and
accordingly different people-s view points could be satisfied. These
two aspects will be discussed completely throughout this paper.
Abstract: Heating systems are a necessity for regions which
brace extreme cold weather throughout the year. To maintain a comfortable temperature inside a given place, heating systems
making use of- Hydronic boilers- are used. The principle of a single
pipe system serves as a base for their working. It is mandatory for these heating systems to control the room temperature, thus
maintaining a warm environment. In this paper, the concept of regulation of the room temperature over a wide range is established
by using an Adaptive Fuzzy Controller (AFC). This fuzzy controller automatically detects the changes in the outside temperatures and
correspondingly maintains the inside temperature to a palatial value. Two separate AFC's are put to use to carry out this function: one to
determine the quantity of heat needed to reach the prospective temperature required and to set the desired temperature; the other to control the position of the valve, which is directly proportional to the
error between the present room temperature and the user desired temperature. The fuzzy logic controls the position of the valve as per
the requirement of the heat. The amount by which the valve opens or closes is controlled by 5 knob positions, which vary from minimum to maximum, thereby regulating the amount of heat flowing through the valve. For the given test system data, different de-fuzzifier
methods have been implemented and the results are compared. In order to validate the effectiveness of the proposed approach, a fuzzy controller has been designed by obtaining a test data from a real time
system. The simulations are performed in MATLAB and are verified with standard system data. The proposed approach can be implemented for real time applications.
Abstract: This paper starts with a critical view of beautiful female images in the mass media being frequently generated by a stereotypical Korean concept of beauty. Several female beauty myths have evolved in Korea during the present decade. Nearly all of them have formed due to a deeply-ingrained androcentric ideology which objectifies women. Mass media causes the public to hold a distorted concept about female beauty. There is a huge gap between women in reality and representative women in the mass media. It is essential to have an unbiased perception of female images presented in the mass media. Due to cosmetic advertisements projecting contemporary images of female beauty to promote products, cosmetics images will be examined in regard to female beauty myths portrayed by the mass media. This paper will analyze features of female beauty myths in Korea and their intrinsic characteristics.
Abstract: Many water supply systems in Australia are currently
undergoing significant reconfiguration due to reductions in long term
average rainfall and resulting low inflows to water supply reservoirs
since the second half of the 20th century. When water supply systems
undergo change, it is necessary to develop new operating rules,
which should consider climate, because the climate change is likely
to further reduce inflows. In addition, water resource systems are
increasingly intended to be operated to meet complex and multiple
objectives representing social, economic, environmental and
sustainability criteria. This is further complicated by conflicting
preferences on these objectives from diverse stakeholders. This paper
describes a methodology to develop optimum operating rules for
complex multi-reservoir systems undergoing significant change,
considering all of the above issues. The methodology is demonstrated
using the Grampians water supply system in northwest Victoria,
Australia. Initial work conducted on the project is also presented in
this paper.
Abstract: Heart sound is an acoustic signal and many techniques
used nowadays for human recognition tasks borrow speech recognition
techniques. One popular choice for feature extraction of accoustic
signals is the Mel Frequency Cepstral Coefficients (MFCC) which
maps the signal onto a non-linear Mel-Scale that mimics the human
hearing. However the Mel-Scale is almost linear in the frequency
region of heart sounds and thus should produce similar results with
the standard cepstral coefficients (CC). In this paper, MFCC is
investigated to see if it produces superior results for PCG based
human identification system compared to CC. Results show that the
MFCC system is still superior to CC despite linear filter-banks in
the lower frequency range, giving up to 95% correct recognition rate
for MFCC and 90% for CC. Further experiments show that the high
recognition rate is due to the implementation of filter-banks and not
from Mel-Scaling.
Abstract: This paper presents a numerical approach for the static
and dynamic analysis of hydrodynamic radial journal bearings. In the
first part, the effect of shaft and housing deformability on pressure
distribution within oil film is investigated. An iterative algorithm that
couples Reynolds equation with a plane finite elements (FE)
structural model is solved. Viscosity-to-pressure dependency (Vogel-
Barus equation) is also included. The deformed lubrication gap and
the overall stress state are obtained. Numerical results are presented
with reference to a typical journal bearing configuration at two
different inlet oil temperatures. Obtained results show the great
influence of bearing components structural deformation on oil
pressure distribution, compared with results for ideally rigid
components. In the second part, a numerical approach based on
perturbation method is used to compute stiffness and damping
matrices, which characterize the journal bearing dynamic behavior.
Abstract: In this paper three different approaches for person
verification and identification, i.e. by means of fingerprints, face and
voice recognition, are studied. Face recognition uses parts-based
representation methods and a manifold learning approach. The
assessment criterion is recognition accuracy. The techniques under
investigation are: a) Local Non-negative Matrix Factorization
(LNMF); b) Independent Components Analysis (ICA); c) NMF with
sparse constraints (NMFsc); d) Locality Preserving Projections
(Laplacianfaces). Fingerprint detection was approached by classical
minutiae (small graphical patterns) matching through image
segmentation by using a structural approach and a neural network as
decision block. As to voice / speaker recognition, melodic cepstral
and delta delta mel cepstral analysis were used as main methods, in
order to construct a supervised speaker-dependent voice recognition
system. The final decision (e.g. “accept-reject" for a verification
task) is taken by using a majority voting technique applied to the
three biometrics. The preliminary results, obtained for medium
databases of fingerprints, faces and voice recordings, indicate the
feasibility of our study and an overall recognition precision (about
92%) permitting the utilization of our system for a future complex
biometric card.
Abstract: Wireless Sensor Networks (WSNs) have attracted the attention of many researchers. This has resulted in their rapid integration in very different areas such as precision agriculture,environmental monitoring, object and event detection and military surveillance. Due to the current WSN characteristics this technology is specifically useful in industrial areas where security, reliability and autonomy are basic, such as nuclear power plants, chemical plants, and others. In this paper we present a system based on WSNs to monitor environmental conditions around and inside a nuclear power plant, specifically, radiation levels. Sensor nodes, equipped with radiation sensors, are deployed in fixed positions throughout the plant. In addition, plant staff are also equipped with mobile devices with higher capabilities than sensors such as for example PDAs able to monitor radiation levels and other conditions around them. The system enables communication between PDAs, which form a Mobile Ad-hoc Wireless Network (MANET), and allows workers to monitor remote conditions in the plant. It is particularly useful during stoppage periods for inspection or in the event of an accident to prevent risk situations.
Abstract: This paper investigates the relationship between state and business in the context of structural and institutional transformations in Indonesia following the collapse of the New Order regime in 1998. Since 1998, Indonesia has embarked on a shift from an authoritarian to democratic polity and from a centralised to a decentralised system of governance, transforming the country into the third largest democracy and one of the most decentralised states in the world. This paper examines whether the transformation of the Indonesian state has altered the pattern of state and business relations with focus on clientism and corruption as the key dependent variable, and probes how/to what extent this has changed as a result of the transformation and the ensuring shifts in business and state relations. Based on interviews with key government and business actors as well as prominent scholars in Indonesia, it is found that since the demise of the New Order, business associations in Indonesia have become more independent of state control and more influential in public decision-making whereas the government has become more responsive of business concerns and more committed to combat corruption and clientism. However, these changes have not necessarily rendered business people completely leave individualclientelistic relationship with the government, and simply pursue wider sectoral and business-wide collectivism as an alternative way of channelling their aspirations, which is expected to help reduce corruption and clientism in Indonesia. This paper concludes that democratisation and a more open politics may have helped reduce corruption and clientism in Indonesia through changes in government. However, it is still difficult to imply that such political transformation has fostered business collective action and a broader, more encompassing pattern of business lobbying and activism, which is expected to help reduce corruption and clientism.