Abstract: This paper presents the development of a software
application for Off-line robot task programming and simulation. Such
application is designed to assist in robot task planning and to direct
manipulator motion on sensor based programmed motion. The
concept of the designed programming application is to use the power
of the knowledge base for task accumulation. In support of the
programming means, an interactive graphical simulation for
manipulator kinematics was also developed and integrated into the
application as the complimentary factor to the robot programming
media. The simulation provides the designer with useful,
inexpensive, off-line tools for retain and testing robotics work cells
and automated assembly lines for various industrial applications.
Abstract: This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc-motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc-motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600, 2340 L/d respectively. The hourly global solar radiation during the day is an average of 506 W/m2. This study also presents the I-V characteristics of the panel at global radiations 200, 400, 600, 800 and 1000 W/m2 matched with the operation of the pump at the above lifting heads. It proves that the only solar radiations 800 and 1000 W/m2 could provide lifting head from 1m to 7m. The analysis shows the best efficiency point of the performance of solar cell panel system occurs at the pumping head 2.89 m.
Abstract: Full adders are important components in applications
such as digital signal processors (DSP) architectures and
microprocessors. In addition to its main task, which is adding two
numbers, it participates in many other useful operations such as
subtraction, multiplication, division,, address calculation,..etc. In
most of these systems the adder lies in the critical path that
determines the overall speed of the system. So enhancing the
performance of the 1-bit full adder cell (the building block of the
adder) is a significant goal.Demands for the low power VLSI have
been pushing the development of aggressive design methodologies to
reduce the power consumption drastically. To meet the growing
demand, we propose a new low power adder cell by sacrificing the
MOS Transistor count that reduces the serious threshold loss
problem, considerably increases the speed and decreases the power
when compared to the static energy recovery full (SERF) adder. So a
new improved 14T CMOS l-bit full adder cell is presented in this
paper. Results show 50% improvement in threshold loss problem,
45% improvement in speed and considerable power consumption
over the SERF adder and other different types of adders with
comparable performance.
Abstract: This paper deals about four items assembly process of
linear drive. This assembly will be realized in flexible assembly cell
on Institute of Manufacturing Systems and Applied Mechanics. There
is defined manufacturing cell, individual actuators created our
flexible cell. Next chapter is about control type, detailed describe a
sequence control type, which will be used in mentioned flexible
assembly cell. All cell control is divided in individual steps
instructions. There instructions illustrate table number III.
Abstract: Since 1992, year where Hugo de Garis has published
the first paper on Evolvable Hardware (EHW), a period of intense
creativity has followed. It has been actively researched, developed
and applied to various problems. Different approaches have been
proposed that created three main classifications: extrinsic, mixtrinsic
and intrinsic EHW. Each of these solutions has a real interest.
Nevertheless, although the extrinsic evolution generates some
excellent results, the intrinsic systems are not so advanced. This
paper suggests 3 possible solutions to implement the run-time
configuration intrinsic EHW system: FPGA-based Run-Time
Configuration system, JBits-based Run-Time Configuration system
and Multi-board functional-level Run-Time Configuration system.
The main characteristic of the proposed architectures is that they are
implemented on Field Programmable Gate Array. A comparison of
proposed solutions demonstrates that multi-board functional-level
run-time configuration is superior in terms of scalability, flexibility
and the implementation easiness.
Abstract: In this paper, by using Mawhin-s continuation theorem of coincidence degree and a method based on delay differential inequality, some sufficient conditions are obtained for the existence and global exponential stability of periodic solutions of cellular neural networks with distributed delays and impulses on time scales. The results of this paper generalized previously known results.
Abstract: The potential of economically cheaper cellulose
containing natural materials like rice husk was assessed for nickel
adsorption from aqueous solutions. The effects of pH, contact time,
sorbent dose, initial metal ion concentration and temperature on the
uptake of nickel were studied in batch process. The removal of nickel
was dependent on the physico-chemical characteristics of the
adsorbent, adsorbate concentration and other studied process
parameters. The sorption data has been correlated with Langmuir,
Freundlich and Dubinin-Radush kevich (D-R) adsorption models. It
was found that Freundlich and Langmuir isotherms fitted well to the
data. Maximum nickel removal was observed at pH 6.0. The
efficiency of rice husk for nickel removal was 51.8% for dilute
solutions at 20 g L-1 adsorbent dose. FTIR, SEM and EDAX were
recorded before and after adsorption to explore the number and
position of the functional groups available for nickel binding on to
the studied adsorbent and changes in surface morphology and
elemental constitution of the adsorbent. Pseudo-second order model
explains the nickel kinetics more effectively. Reusability of the
adsorbent was examined by desorption in which HCl eluted 78.93%
nickel. The results revealed that nickel is considerably adsorbed on
rice husk and it could be and economic method for the removal of
nickel from aqueous solutions.
Abstract: We address the problem of joint beamforming and multipath channel parameters estimation in Wideband Code Division Multiple Access (WCDMA) communication systems that employ Multiple-Access Interference (MAI) suppression techniques in the uplink (from mobile to base station). Most of the existing schemes rely on time multiplex a training sequence with the user data. In WCDMA, the channel parameters can also be estimated from a code multiplexed common pilot channel (CPICH) that could be corrupted by strong interference resulting in a bad estimate. In this paper, we present new methods to combine interference suppression together with channel estimation when using multiple receiving antennas by using adaptive signal processing techniques. Computer simulation is used to compare between the proposed methods and the existing conventional estimation techniques.
Abstract: Serial Analysis of Gene Expression is a powerful
quantification technique for generating cell or tissue gene expression
data. The profile of the gene expression of cell or tissue in several
different states is difficult for biologists to analyze because of the large
number of genes typically involved. However, feature selection in
machine learning can successfully reduce this problem. The method
allows reducing the features (genes) in specific SAGE data, and
determines only relevant genes. In this study, we used a genetic
algorithm to implement feature selection, and evaluate the
classification accuracy of the selected features with the K-nearest
neighbor method. In order to validate the proposed method, we used
two SAGE data sets for testing. The results of this study conclusively
prove that the number of features of the original SAGE data set can be
significantly reduced and higher classification accuracy can be
achieved.
Abstract: Acute disseminated encephalomyelitis (ADEM) has
been reported to develop after a hymenoptera sting, but its
pathogenesis is not known in detail. Myelin basic protein (MBP)-
specific T cells have been detected in the blood of patients with
ADEM, and a proportion of these patients develop multiple sclerosis
(MS). In an attempt to understand the mechanisms underlying
ADEM, molecular mimicry between hymenoptera venom peptides
and the human immunodominant MBP peptide was scrutinized,
based on the sequence and structural similarities, whether it was the
root of the disease. The results suggest that the three wasp venom
peptides have low sequence homology with the human
immunodominant MBP residues 85-99. Structural similarity analysis
among the three venom peptides and the MS-related HLA-DR2b
(DRA, DRB1*1501)-associated immunodominant MHC
binding/TCR contact residues 88-93, VVHFFK showed that
hyaluronidase residues 7-12, phospholipase A1 residues 98-103, and
antigen 5 residues 109-114 showed a high degree of similarity
83.3%, 100%, and 83.3% respectively. In conclusion, some wasp
venom peptides, particularly phospholipase A1, may potentially act
as the molecular motifs of the human 3HLA-DR2b-associated
immunodominant MBP88-93, and possibly present a mechanism for
induction of wasp sting-associated ADEM.
Abstract: It has been shown that pH 7,3 and 37 0C are the optimal condition for the growth of E. coli “ASAP". The cells grow well on Glucose, Lactose, D-Mannitol, D-Sorbitol, (+)-Xylose, L- (+)-Arabinose and Dulcitol. No growth has been observed on Sucrose, Inositol, Phenylalanine, and Tryptophan. The strain is sensitive to a range of antibiotics. The present study has demonstrated that E. coli “ASAP" inhibit the growth of S. enterica ATCC #700931 in vitro. The studies on conjugating activity has revealed no conjugant of E. coli “ASAP" with plasmid strains E. coli G35#59 and S. enterica ATCC #700931. On the other hand, the conjugants with low frequencies were obtained from E. coli “ASAP" with E. coli G35#61, and E. coli “ASAP" with randomly chosen isolate from healthy human gut microflora: E. coli E6. The results of present study have demonstrated improvements in gut microflora condition of patients with different diseases after the administration of “ASAP"
Abstract: In this study acoustic emission (AE) signals obtained during deformation and fracture of two types of ferrite-martensite dual phase steels (DPS) specimens have been analyzed in frequency domain. For this reason two low carbon steels with various amounts of carbon were chosen, and intercritically heat treated. In the introduced method, identifying the mechanisms of failure in the various phases of DPS is done. For this aim, AE monitoring has been used during tensile test of several DPS with various volume fraction of the martensite (VM) and attempted to relate the AE signals and failure mechanisms in these steels. Different signals, which referred to 2-3 micro-mechanisms of failure due to amount of carbon and also VM have been seen. By Fast Fourier Transformation (FFT) of signals in distinct locations, an excellent relationship between peak frequencies in these areas and micro-mechanisms of failure were seen. The results were verified by microscopic observations (SEM).
Abstract: In this paper, a new cooling system using a nacelle duct
is proposed for the mechanical room in the household refrigerator. The
conventional mechanical room consists of a condenser, a compressor
and an axial fan. The axial fan is mainly responsible for cooling the
condenser and the compressor. The new cooling system is developed
by replacing the axial fan with the nacelle duct including the small
centrifugal fan. The parametric study is carried out to find the optimum
designs of the nacelle duct in terms of performance and efficiency.
Through this study, it is revealed that the new system can reduce the
space, electrical power and noise compared with the conventional
system
Abstract: The neurogenic potential of many herbal extracts used
in Indian medicine is hitherto unknown. Extracts derived from
Clitoria ternatea Linn have been used in Indian Ayurvedic system of
medicine as an ingredient of “Medhya rasayana", consumed for
improving memory and longevity in humans and also in treatment of
various neurological disorders. Our earlier experimental studies with
oral intubation of Clitoria ternatea aqueous root extract (CTR) had
shown significant enhancement of learning and memory in postnatal
and young adult Wistar rats. The present study was designed to
elucidate the in vitro effects of 200ng/ml of CTR on proliferation,
differentiation and growth of anterior subventricular zone neural
stem cells (aSVZ NSC-s) derived from prenatal and postnatal rat
pups. Results show significant increase in proliferation and growth of
neurospheres and increase in the yield of differentiated neurons of
aSVZ neural precursor cells (aSVZNPC-s) at 7 days in vitro when
treated with 200ng/ml of CTR as compared to age matched control.
Results indicate that CTR has growth promoting neurogenic effect on
aSVZ neural stem cells and their survival similar to neurotrophic
factors like Survivin, Neuregulin 1, FGF-2, BDNF possibly the basis
for enhanced learning and memory.
Abstract: In this paper we compare the accuracy of data mining
methods to classifying students in order to predicting student-s class
grade. These predictions are more useful for identifying weak
students and assisting management to take remedial measures at early
stages to produce excellent graduate that will graduate at least with
second class upper. Firstly we examine single classifiers accuracy on
our data set and choose the best one and then ensembles it with a
weak classifier to produce simple voting method. We present results
show that combining different classifiers outperformed other single
classifiers for predicting student performance.
Abstract: Landfill gas, particularly methane is one of the
greenhouse gases which contributes to global warming. This paper presents the findings of a study on methane gas production from
simulated landfill reactor under saturated conditions. A reactor was constructed to represent a landfill cell of 2.5 m thickness on sandy
soil. The reactor was 0.2 m in diameter and 4 m in height. One meter of sand and pebble layer was packed at the bottom of the reactor
followed by 2.5 m of solid waste layer and 0.4 m of sand layer as the cover soil. Degradation of waste in the solid waste layer was at
acidification stage as indicated by the leachate quality with COD as
high as 55,511 mg/L and pH as low as 5.1. However, methanogenic
environment was established at the bottom sand layer after one year of operation indicated by pH of 7.2 and methane gas generation.
Leachate degradation took place as the leachate moved through the
sand layer at an infiltration of rate 0.7 cm/day. This resulted in landfill gas production of 77 mL/day/kg containing 55 to 65% methane. The application of sand layer contributed to the gas
production from landfill by an in-situ degradation of leachate in the
sand at the bottom of the landfill.
Abstract: To compress, improve bit error performance and also enhance 2D images, a new scheme, called Iterative Cellular-Turbo System (IC-TS) is introduced. In IC-TS, the original image is partitioned into 2N quantization levels, where N is denoted as bit planes. Then each of the N-bit-plane is coded by Turbo encoder and transmitted over Additive White Gaussian Noise (AWGN) channel. At the receiver side, bit-planes are re-assembled taking into consideration of neighborhood relationship of pixels in 2-D images. Each of the noisy bit-plane values of the image is evaluated iteratively using IC-TS structure, which is composed of equalization block; Iterative Cellular Image Processing Algorithm (ICIPA) and Turbo decoder. In IC-TS, there is an iterative feedback link between ICIPA and Turbo decoder. ICIPA uses mean and standard deviation of estimated values of each pixel neighborhood. It has extra-ordinary satisfactory results of both Bit Error Rate (BER) and image enhancement performance for less than -1 dB Signal-to-Noise Ratio (SNR) values, compared to traditional turbo coding scheme and 2-D filtering, applied separately. Also, compression can be achieved by using IC-TS systems. In compression, less memory storage is used and data rate is increased up to N-1 times by simply choosing any number of bit slices, sacrificing resolution. Hence, it is concluded that IC-TS system will be a compromising approach in 2-D image transmission, recovery of noisy signals and image compression.
Abstract: Protective coatings that resist oxide scale growth and
decrease chromium evaporation are necessary to make stainless steel
interconnect materials for long-term durable operation of solid oxide
fuel cells (SOFCs). In this study a layer of cobalt was electroplated
on the surface of AISI 441 ferritic stainless steel which is used in
solid oxide fuel cells for interconnect applications. The oxidation
behavior of coated substrates was studied as a function of time at
operating conditions of SOFCs. Cyclic oxidation has been also tested
at 800ºC for 100 cycles. Cobalt coating during isothermal oxidation
caused to the oxide growth resistance by limiting the outward
diffusion of Cr cation and the inward diffusion of oxygen anion.
Results of cyclic oxidation exhibited that coated substrates
demonstrate an excellent resistance against the spallation and
cracking.
Abstract: The agriculture lignocellulosic by-products are receiving increased attention, namely in the search for filter materials that retain contaminants from water. These by-products, specifically almond and hazelnut shells are abundant in Portugal once almond and hazelnuts production is a local important activity. Hazelnut and almond shells have as main constituents lignin, cellulose and hemicelluloses, water soluble extractives and tannins. Along the adsorption of heavy metals from contaminated waters, water soluble compounds can leach from shells and have a negative impact in the environment. Usually, the chemical characterization of treated water by itself may not show environmental impact caused by the discharges when parameters obey to legal quality standards for water. Only biological systems can detect the toxic effects of the water constituents. Therefore, the evaluation of toxicity by biological tests is very important when deciding the suitability for safe water discharge or for irrigation applications.
The main purpose of the present work was to assess the potential impacts of waters after been treated for heavy metal removal by hazelnut and almond shells adsorption systems, with short term acute toxicity tests.
To conduct the study, water at pH 6 with 25 mg.L-1 of lead, was treated with 10 g of shell per litre of wastewater, for 24 hours. This procedure was followed for each bark. Afterwards the water was collected for toxicological assays; namely bacterial resistance, seed germination, Lemna minor L. test and plant grow. The effect in isolated bacteria strains was determined by disc diffusion method and the germination index of seed was evaluated using lettuce, with temperature and humidity germination control for 7 days. For aquatic higher organism, Lemnas were used with 4 days contact time with shell solutions, in controlled light and temperature. For terrestrial higher plants, biomass production was evaluated after 14 days of tomato germination had occurred in soil, with controlled humidity, light and temperature.
Toxicity tests of water treated with shells revealed in some extent effects in the tested organisms, with the test assays showing a close behaviour as the control, leading to the conclusion that its further utilization may not be considered to create a serious risk to the environment.
Abstract: Maximal Ratio Combining (MRC) is considered the most complex combining technique as it requires channel coefficients estimation. It results in the lowest bit error rate (BER) compared to all other combining techniques. However the BER starts to deteriorate as errors are introduced in the channel coefficients estimation. A novel combining technique, termed Generalized Maximal Ratio Combining (GMRC) with a polynomial kernel, yields an identical BER as MRC with perfect channel estimation and a lower BER in the presence of channel estimation errors. We show that GMRC outperforms the optimal MRC scheme in general and we hereinafter introduce it to the scientific community as a new “supraoptimal" algorithm. Since diversity combining is especially effective in small femto- and pico-cells, internet-associated wireless peripheral systems are to benefit most from GMRC. As a result, many spinoff applications can be made to IP-based 4th generation networks.