Abstract: These Monolayer and multilayer coatings of CrN and
AlCrN deposited on 100Cr6 (AISI 52100) substrate by PVD
magnetron sputtering system. The microstructures of the coatings
were characterized using atomic force microscopy (AFM). The AFM
analysis revealed the presence of domes and craters that are
uniformly distributed over all surfaces of the various layers.
Nanoindentation measurement of CrN coating showed maximum
hardness (H) and modulus (E) of 14 GPa and 190 GPa, respectively.
The measured H and E values of AlCrN coatings were found to be 30
GPa and 382 GPa, respectively. The improved hardness in both the
coatings was attributed mainly to a reduction in crystallite size and
decrease in surface roughness. The incorporation of Al into the CrN
coatings has improved both hardness and Young’s modulus.
Abstract: The main parameters affecting the workability are the
water content, particle size, and the total surface of the grains, as long
as the mixing water begins by wetting the surface of the grains and
then fills the voids between the grains to form entrapped water, the
quantity of water remaining is called free water. The aim of this study is to undertake a fractal approach through
the relationship between the concrete formulation parameters and
workability. To develop this approach a series of concrete taken from
the literature was investigated by varying formulation parameters
such as G/S, the quantity of cement C and the quantity of water W. We also call another model as the model of water layer thickness
and model of paste layer thickness to judge their relevance, hence the
following results: the relevance of the water layer thickness model is
considered as a relevant when there is a variation in the water
quantity. The model of the paste layer thickness is only applicable if
we considered that the paste is made with the grain value Dmax =
2.85: value from which we see a stability of the model.
Abstract: This paper describes a new approach which can be
used to interpret the experimental creep deformation data obtained
from miniaturized thin plate bending specimen test to the
corresponding uniaxial data based on an inversed application of the
reference stress method. The geometry of the thin plate is fully
defined by the span of the support, l, the width, b, and the thickness,
d. Firstly, analytical solutions for the steady-state, load-line creep
deformation rate of the thin plates for a Norton’s power law under
plane stress (b→0) and plane strain (b→∞) conditions were obtained,
from which it can be seen that the load-line deformation rate of the
thin plate under plane-stress conditions is much higher than that
under the plane-strain conditions. Since analytical solution is not
available for the plates with random b-values, finite element (FE)
analyses are used to obtain the solutions. Based on the FE results
obtained for various b/l ratios and creep exponent, n, as well as the
analytical solutions under plane stress and plane strain conditions, an
approximate, numerical solutions for the deformation rate are
obtained by curve fitting. Using these solutions, a reference stress
method is utilised to establish the conversion relationships between
the applied load and the equivalent uniaxial stress and between the
creep deformations of thin plate and the equivalent uniaxial creep
strains. Finally, the accuracy of the empirical solution was assessed
by using a set of “theoretical” experimental data.
Abstract: This paper investigates the parametric stability of an
axially moving web subjected to non-uniform in-plane edge
excitations on two opposite, simply-supported edges. The web is
modeled as a viscoelastic plate whose constitutive relation obeys the
Kelvin-Voigt model, and the in-plane edge excitations are expressed
as the sum of a static tension and a periodical perturbation. Due to the
in-plane edge excitations, the moving plate may bring about
parametric instability under certain situations. First, the in-plane
stresses of the plate due to the non-uniform edge excitations are
determined by solving the in-plane forced vibration problem. Then,
the dependence on the spatial coordinates in the equation of transverse
motion is eliminated by the generalized Galerkin method, which
results in a set of discretized system equations in time. Finally, the
method of multiple scales is utilized to solve the set of system
equations analytically if the periodical perturbation of the in-plane
edge excitations is much smaller as compared with the static tension of
the plate, from which the stability boundaries of the moving plate are
obtained. Numerical results reveal that only combination resonances
of the summed-type appear under the in-plane edge excitations
considered in this work.
Abstract: In this study, the signal of brain electrical activities of
the sixteen students selected from the Department of Electrical and
Energy at Usak University have been recorded during a lecturer
performed happiness emotions for the first group and anger emotions
for the second group in different time while the groups were in the
classroom separately. The attention and meditation data extracted
from the recorded signals have been analyzed and evaluated toward
the teacher’s specific emotion states simultaneously. Attention levels
of students who are under influence of happiness emotions of the
lecturer have a positive trend and attention levels of students who are
under influence of anger emotions of the lecturer have a negative
trend. The meditation or mental relaxation levels of students who are
under influence of happiness emotions of the lecturer are 34.3%
higher comparing with the mental relaxation levels of students who
are under influence of anger emotions of the lecturer.
Abstract: Numerical studies have been carried out using a
validated two-dimensional standard k-omega turbulence model for
the design optimization of a thrust vector control system using shock
induced self-impinging supersonic secondary double jet. Parametric
analytical studies have been carried out at different secondary
injection locations to identifying the highest unsymmetrical
distribution of the main gas flow due to shock waves, which produces
a desirable side force more lucratively for vectoring. The results from
the parametric studies of the case on hand reveal that the shock
induced self-impinging supersonic secondary double jet is more
efficient in certain locations at the divergent region of a CD nozzle
than a case with supersonic single jet with same mass flow rate. We
observed that the best axial location of the self-impinging supersonic
secondary double jet nozzle with a given jet interaction angle, built-in
to a CD nozzle having area ratio 1.797, is 0.991 times the primary
nozzle throat diameter from the throat location. We also observed
that the flexible steering is possible after invoking ON/OFF facility to
the secondary nozzles for meeting the onboard mission requirements.
Through our case studies we concluded that the supersonic self-impinging
secondary double jet at predesigned jet interaction angle
and location can provide more flexible steering options facilitating
with 8.81% higher thrust vectoring efficiency than the conventional
supersonic single secondary jet without compromising the payload
capability of any supersonic aerospace vehicle.
Abstract: In this study, lipid-deprived residuals of microalgae
were hydrolyzed for the production of reducing sugars by using the
recombinant Bacillus cellulosome, carrying eight genes from the
Clostridium thermocellum ATCC27405. The obtained cellulosome
was found to exist mostly in the broth supernatant with a cellulosome
activity of 2.4 U/mL. Furthermore, the Michaelis-Menten constant
(Km) and Vmax of cellulosome were found to be 14.832 g/L and 3.522
U/mL. The activation energy of the cellulosome to hydrolyze
microalgae LDRs was calculated as 32.804 kJ/mol.
Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: This study conducts simulation analyses to find the
optimal debt ceiling of Taiwan, while factoring in welfare
maximization under a dynamic stochastic general equilibrium
framework. The simulation is based on Taiwan's 2001 to 2011
economic data and shows that welfare is maximized at a debt/GDP
ratio of 0.2, increases in the debt/GDP ratio leads to increases in both
tax and interest rates and decreases in the consumption ratio and
working hours. The study results indicate that the optimal debt ceiling
of Taiwan is 20% of GDP, where if the debt/GDP ratio is greater than
40%, the welfare will be negative and result in welfare loss.
Abstract: The main objective of this study was to determine the
effects of Nitrogen fixing bacteria and manure application on the seed
yield and yield components in black cumin (Nigella sativa L.). The
experiment was carried out at the RAN Research Station in
Firouzkouh in 2012. A 4×4 factorial experiment, arranged in a
randomized complete blocks designed with three replications.
Nitrogen fixing bacteria at 4 levels (control, Azotobacter,
Azospirillum and Azotobacter + Azospirillum) and manure
application at 4 levels (0, 2.5, 5 and 7.5 ton ha-1) were used at this
investigation. The present results have shown that the highest height,
1000 seeds weight, seed number per follicle, follicle yield, seed yield
and harvest index were obtained after using Azotobacter and
Azospirillum, simultaneously. Manure application only effects on
follicle yield and by 5ton manure ha-1 the highest follicle yield
obtained. Results of this investigation showed that the maximum seed
yield obtained when Aotobacter+Azospirillum inoculated with black
cumin seeds and 5 ton manure ha-1 applied. According to the results
of this investigation the integrated management of Azotobacter and
Azospirillum with manure application is the best treatment for
achieving the maximum quantitative charactersitics of Black cumin.
Abstract: This paper presents results of compressive strength,
capillary water absorption, and density tests conducted on concrete
containing recycled aggregate (RCA) which is obtained from
structural waste generated by the construction industry in Turkey. In
the experiments, 0%, 15%, 30%, 45% and 60% of the normal
(natural) coarse aggregate was replaced by the recycled aggregate.
Maximum aggregate particle sizes were selected as 16 mm, 22,4 mm
and 31,5 mm; and 0,06%, 0,13% and 0,20% of air-entraining agent
(AEA) were used in mixtures. Fly ash and superplasticizer were used
as a mineral and chemical admixture, respectively. The same type
(CEM I 42.5) and constant dosage of cement were used in the study.
Water/cement ratio was kept constant as 0.53 for all mixture. It was
concluded that capillary water absorption, compressive strength, and
density of concrete decreased with increasing RCA ratio. Increasing
in maximum aggregate particle size and amount of AEA also affect
the properties of concrete significantly.
Abstract: Based on Business and Consumer Survey (BCS) data,
the European Commission (EC) regularly publishes the monthly
Economic Sentiment Indicator (ESI) for each EU member state. ESI
is conceptualized as a leading indicator, aimed ad tracking the overall
economic activity. In calculating ESI, the EC employs arbitrarily
chosen weights on 15 BCS response balances. This paper raises the
predictive quality of ESI by applying nonlinear programming to find
such weights that maximize the correlation coefficient of ESI and
year-on-year GDP growth. The obtained results show that the highest
weights are assigned to the response balances of industrial sector
questions, followed by questions from the retail trade sector. This
comes as no surprise since the existing literature shows that the
industrial production is a plausible proxy for the overall Croatian
economic activity and since Croatian GDP is largely influenced by
the aggregate personal consumption.
Abstract: Waste Load Allocation (WLA) strategies usually
intend to find economic policies for water resource management.
Water quality trading (WQT) is an approach that uses discharge
permit market to reduce total environmental protection costs. This
primarily requires assigning discharge limits known as total
maximum daily loads (TMDLs). These are determined by monitoring
organizations with respect to the receiving water quality and
remediation capabilities. The purpose of this study is to compare two
approaches of TMDL assignment for WQT policy in small catchment
area of Haraz River, in north of Iran. At first, TMDLs are assigned
uniformly for the whole point sources to keep the concentrations of
BOD and dissolved oxygen (DO) at the standard level at checkpoint
(terminus point). This was simply simulated and controlled by
Qual2kw software. In the second scenario, TMDLs are assigned
using multi objective particle swarm optimization (MOPSO) method
in which the environmental violation at river basin and total treatment
costs are minimized simultaneously. In both scenarios, the equity
index and the WLA based on trading discharge permits (TDP) are
calculated. The comparative results showed that using economically
optimized TMDLs (2nd scenario) has slightly more cost savings rather
than uniform TMDL approach (1st scenario). The former annually
costs about 1 M$ while the latter is 1.15 M$. WQT can decrease
these annual costs to 0.9 and 1.1 M$, respectively. In other word,
these approaches may save 35 and 45% economically in comparison
with command and control policy. It means that using multi objective
decision support systems (DSS) may find more economical WLA,
however its outcome is not necessarily significant in comparison with
uniform TMDLs. This may be due to the similar impact factors of
dischargers in small catchments. Conversely, using uniform TMDLs
for WQT brings more equity that makes stakeholders not feel that
much envious of difference between TMDL and WQT allocation. In
addition, for this case, determination of TMDLs uniformly would be
much easier for monitoring. Consequently, uniform TMDL for TDP
market is recommended as a sustainable approach. However,
economical TMDLs can be used for larger watersheds.
Abstract: Haynes 25 alloy (also known as L-605 alloy) is cobalt
based super alloy which has widely applications such as aerospace
industry, turbine and furnace parts, power generators and heat
exchangers and petroleum refining components due to its excellent
characteristics. However, the workability of this alloy is more
difficult compared to normal steels or even stainless. In present work,
an experimental investigation was performed under cryogenic
cooling to determine cutting tool wear patterns and obtain optimal
cutting parameters in turning of cobalt based superalloy Haynes 25.
In experiments, uncoated carbide tool was used and cutting speed (V)
and feed rate (f) were considered as test parameters. Tool wear
(VBmax) were measured for process performance indicators.
Analysis of variance (ANOVA) was performed to determine the
importance of machining parameters.
Abstract: This paper presents a rheological model for producing
shape-memory thermoplastic polymers. Shape-memory occurs as a
result of internal rearrangement of the structural elements of a
polymer. A non-linear viscoelastic model was developed that allows
qualitative and quantitative prediction of the stress-strain behavior of
shape-memory polymers during heating. This research was done to
develop a technique to determine the maximum possible change in
size of shape-memory products during heating. The rheological
model used in this work was particularly suitable for defining process
parameters and constructive parameters of the processing equipment.
Abstract: Background: Delayed onset muscle soreness (DOMS)
is the most common symptom when ordinary individuals and athletes
are exposed to unaccustomed physical activity, especially eccentric
contraction which impairs athletic performance, ordinary people
work ability and physical functioning. Multitudes of methods have
been investigated to reduce DOMS. One of the valuable methods to
control DOMS is repeated bout effect (RBE) as a prophylactic
method. Purpose: To compare the repeated bout effect of
submaximal eccentric with maximal isometric contraction on induced
DOMS. Methods: Sixty normal male volunteers were assigned
randomly into three equal groups: Group A (first study group): 20
subjects received submaximal eccentric contraction on non-dominant
elbow flexors as a prophylactic exercise. Group B (second study
group): 20 subjects received maximal isometric contraction on nondominant
elbow flexors as a prophylactic exercise. Group C (control
group): 20 subjects did not receive any prophylactic exercises.
Maximal isometric peak torque of elbow flexors and patient related
elbow evaluation (PREE) scale were measured for each subject 3
times before, immediately after, and 48 hours after induction of
DOMS. Results: Post-hoc test for maximal isometric peak torque and
PREE scale immediately and 48 hours after induction of DOMS
revealed that group (A) and group (B) resulted in significant decrease
in maximal isometric strength loss and elbow pain and disability
rather than control group (C), but submaximal eccentric group (A)
was more effective than maximal isometric group (B) as it showed
more rapid recovery of functional strength and less degrees of elbow
pain and disability. Conclusion: Both submaximal eccentric
contraction and maximal isometric contraction were effective in
prevention of DOMS but submaximal eccentric contraction produced
a greater protective effect against muscle damage induced by
maximal eccentric exercise performed 2 days later.
Abstract: One of the functions of the commercial heavy vehicle
is to safely and efficiently transport goods and people. Due to its size
and carrying capacity, it is important to study the vehicle dynamic
stability during cornering. Study has shown that there are a number of
overloaded heavy vehicles or permissible Gross Vehicle Weight
(GVW) violations recorded at selected areas in Malaysia assigned by
its type and category. Thus, the objective of this study is to
investigate the correlation and effect of the GVW on heavy vehicle
stability during cornering event using simulation. Various selected
heavy vehicle types and category are simulated using IPG/Truck
Maker® with different GVW and road condition (coefficient of
friction of road surface), while the speed, driver characteristic, center
of gravity of load and road geometry are constant. Based on the
analysis, the relationship between GVW and lateral acceleration were
established. As expected, on the same value of coefficient of friction,
the maximum lateral acceleration would be increased as the GVW
increases.
Abstract: This paper presents an application of Artificial Neural
Network (ANN) algorithm for improving power system voltage
stability. The training data is obtained by solving several normal and
abnormal conditions using the Linear Programming technique. The
selected objective function gives minimum deviation of the reactive
power control variables, which leads to the maximization of
minimum Eigen value of load flow Jacobian. The considered reactive
power control variables are switchable VAR compensators, OLTC
transformers and excitation of generators. The method has been
implemented on a modified IEEE 30-bus test system. The results
obtain from the test clearly show that the trained neural network is
capable of improving the voltage stability in power system with a
high level of precision and speed.
Abstract: Land Use Land Cover (LULC) changes due to human
activities and natural causes have become a major environmental
concern. Assessment of temporal remote sensing data provides
information about LULC impacts on environment. Land Surface
Temperature (LST) is one of the important components for modeling
environmental changes in climatological, hydrological, and
agricultural studies. In this study, LULC changes (September 7, 1984
and July 8, 2014) especially in agricultural lands together with
population changes (1985-2014) and LST status were investigated
using remotely sensed and census data in South Marmara Watershed,
Turkey. LULC changes were determined using Landsat TM and
Landsat OLI data acquired in 1984 and 2014 summers. Six-band TM
and OLI images were classified using supervised classification
method to prepare LULC map including five classes including Forest
(F), Grazing Land (G), Agricultural Land (A), Water Surface (W),
Residential Area-Bare Soil (R-B) classes. The LST image was also
derived from thermal bands of the same dates.
LULC classification results showed that forest areas, agricultural
lands, water surfaces and residential area-bare soils were increased as
65751 ha, 20163 ha, 1924 ha and 20462 ha respectively. In
comparison, a dramatic decrement occurred in grazing land (107985
ha) within three decades. The population increased 29% between
years 1984-2014 in whole study area. Along with the natural causes,
migration also caused this increase since the study area has an
important employment potential. LULC was transformed among the
classes due to the expansion in residential, commercial and industrial
areas as well as political decisions. In the study, results showed that
agricultural lands around the settlement areas transformed to
residential areas in 30 years.
The LST images showed that mean temperatures were ranged
between 26-32°C in 1984 and 27-33°C in 2014. Minimum
temperature of agricultural lands was increased 3°C and reached to
23°C. In contrast, maximum temperature of A class decreased to
41°C from 44°C. Considering temperatures of the 2014 R-B class and
1984 status of same areas, it was seen that mean, min and max
temperatures increased by 2°C.
As a result, the dynamism of population, LULC and LST resulted
in increasing mean and maximum surface temperatures, living
spaces/industrial areas and agricultural lands.
Abstract: It is an established fact that polymers have several
physical limitations such as low stiffness and low resistance to
impact on loading. Hence, polymers do not usually have requisite
mechanical strength for application in various fields. The
reinforcement by high strength fibers provides the polymer
substantially enhanced mechanical properties and makes them more
suitable for a large number of diverse applications. This research
evaluates the effects of particulate Cow bone and Groundnut shell
additions on the mechanical properties and microstructure of cow
bone and groundnut shell reinforced epoxy composite in order to
assess the possibility of using it as a material for engineering
applications. Cow bone and groundnut shell particles reinforced with
epoxy (CBRPC and GSRPC) was prepared by varying the cow bone
and groundnut shell particles from 0-25 wt% with 5 wt% intervals. A
Hybrid of the Cow bone and Groundnut shell (HGSCB) reinforce
with epoxy was also prepared. The mechanical properties of the
developed composites were investigated. Optical microscopy was
used to examine the microstructure of the composites. The results
revealed that mechanical properties did not increase uniformly with
additions in filler but exhibited maximum properties at specific
percentages of filler additions. From the Microscopic evaluation, it
was discovered that homogeneity decreases with increase in % filler,
this could be due to poor interfacial bonding.