Abstract: Evapotranspiration is one of the most important
components of the hydrological cycle. Evapotranspiration (ETo) is an
important variable in water and energy balances on the earth’s
surface, and knowledge of the distribution of ET is a key factor in
hydrology, climatology, agronomy and ecology studies. Many
researchers have a valid relationship, which is a function of climate
factors, to estimate the potential evapotranspiration presented to the
plant water stress or water loss, prevent. The FAO-Penman method
(PM) had been recommended as a standard method. This method
requires many data and these data are not available in every area of
world. So, other methods should be evaluated for these conditions.
When sufficient or reliable data to solve the PM equation are not
available then Hargreaves equation can be used. The Hargreaves
equation (HG) requires only daily mean, maximum and minimum air
temperature extraterrestrial radiation .In this study, Hargreaves
method (HG) were evaluated in 12 stations in the North West region
of Iran. Results of HG and M.HG methods were compared with
results of PM method. Statistical analysis of this comparison showed
that calibration process has had significant effect on efficiency of
Hargreaves method.
Abstract: In recent years, multi-antenna techniques are being considered as a potential solution to increase the flow of future wireless communication systems. The objective of this article is to study the emission and reception system MIMO (Multiple Input Multiple Output), and present the different reception decoding techniques. First we will present the least complex technical, linear receivers such as the zero forcing equalizer (ZF) and minimum mean squared error (MMSE). Then a nonlinear technique called ordered successive cancellation of interferences (OSIC) and the optimal detector based on the maximum likelihood criterion (ML), finally, we simulate the associated decoding algorithms for MIMO system such as ZF, MMSE, OSIC and ML, thus a comparison of performance of these algorithms in MIMO context.
Abstract: The sea waves carry thousands of GWs of power
globally. Although there are a number of different approaches to
harness offshore energy, they are likely to be expensive, practically
challenging, and vulnerable to storms. Therefore, this paper considers
using the near shore waves for generating mechanical and electrical
power. It introduces two new approaches, the wave manipulation and
using a variable duct turbine, for intercepting very wide wave fronts
and coping with the fluctuations of the wave height and the sea level,
respectively. The first approach effectively allows capturing much
more energy yet with a much narrower turbine rotor. The second
approach allows using a rotor with a smaller radius but captures
energy of higher wave fronts at higher sea levels yet preventing it
from totally submerging. To illustrate the effectiveness of the first
approach, the paper contains a description and the simulation results
of a scale model of a wave manipulator. Then, it includes the results
of testing a physical model of the manipulator and a single duct, axial
flow turbine in a wave flume in the laboratory. The paper also
includes comparisons of theoretical predictions, simulation results,
and wave flume tests with respect to the incident energy, loss in wave
manipulation, minimal loss, brake torque, and the angular velocity.
Abstract: In recent years a new method of combination
treatment for cancer has been developed and studied that has led to
significant advancements in the field of cancer therapy. Hyperthermia
is a traditional therapy that, along with a creation of a medically
approved level of heat with the help of an alternating magnetic AC
current, results in the destruction of cancer cells by heat. This paper
gives details regarding the production of the spherical nanocomposite
PVA/γ-Fe2O3 in order to be used for medical purposes such as tumor
treatment by hyperthermia. To reach a suitable and evenly distributed
temperature, the nanocomposite with core-shell morphology and
spherical form within a 100 to 200 nanometer size was created using
phase separation emulsion, in which the magnetic nano-particles γ-
Fe2O3 with an average particle size of 20 nano-meters and with
different percentages of 0.2, 0.4, 0.5 and 0.6 were covered by
polyvinyl alcohol. The main concern in hyperthermia and heat
treatment is achieving desirable specific absorption rate (SAR) and
one of the most critical factors in SAR is particle size. In this project
all attempts has been done to reach minimal size and consequently
maximum SAR. The morphological analysis of the spherical
structure of the nanocomposite PVA/γ-Fe2O3 was achieved by SEM
analyses and the study of the chemical bonds created was made
possible by FTIR analysis. To investigate the manner of magnetic
nanocomposite particle size distribution a DLS experiment was
conducted. Moreover, to determine the magnetic behavior of the γ-
Fe2O3 particle and the nanocomposite PVA/γ-Fe2O3 in different
concentrations a VSM test was conducted. To sum up, creating
magnetic nanocomposites with a spherical morphology that would be
employed for drug loading opens doors to new approaches in
developing nanocomposites that provide efficient heat and a
controlled release of drug simultaneously inside the magnetic field,
which are among their positive characteristics that could significantly
improve the recovery process in patients.
Abstract: Radial profiles of particle velocities were investigated
in a 6.1m high methanol-to-olefins cold model experimental device
using a TSI laser Doppler velocimeter. The effect of axial height on
flow development was not obvious in fully developed region under the
same operating condition. Superficial gas velocity and solid
circulating rate had significant influence on particle velocity in the
center region of the riser. Besides, comparisons among rising,
descending and average particle velocity were conducted. The particle
average velocity was similar to the rising particle velocity and higher
than the descending particle velocity in radial locations except the wall
region of riser.
Abstract: Riveting process is one of the important ways to keep
fastening the lap joints in aircraft structures. Failure of aircraft lap
joints directly depends on the stress field in the joint. An important
application of riveting process is in the construction of aircraft
fuselage structures. In this paper, a 3D finite element method is
carried out in order to optimize residual stress field in a riveted lap
joint and also to estimate its fatigue life. In continue, a number of
experiments are designed and analyzed using design of experiments
(DOE). Then, Taguchi method is used to select an optimized case
between different levels of each factor. Besides that, the factor which
affects the most on residual stress field is investigated. Such
optimized case provides the maximum residual stress field. Fatigue
life of the optimized joint is estimated by Paris-Erdogan law. Stress
intensity factors (SIFs) are calculated using both finite element
analysis and experimental formula. In addition, the effect of residual
stress field, geometry and secondary bending are considered in SIF
calculation. A good agreement is found between results of such
methods. Comparison between optimized fatigue life and fatigue life
of other joints has shown an improvement in the joint’s life.
Abstract: This paper represents the results of experimental work to investigate the suitability of a waste material (WM) for soft soil stabilisation. In addition, the effect of particle size distribution (PSD) of the waste material on its performance as a soil stabiliser was investigated. The WM used in this study is produced from the incineration processes in domestic energy power plant and it is available in two different grades of fineness (coarse waste material (CWM) and fine waste material (FWM)). An intermediate plasticity silty clayey soil with medium organic matter content has been used in this study. The suitability of the CWM and FWM to improve the physical and engineering properties of the selected soil was evaluated dependant on the results obtained from the consistency limits, compaction characteristics (optimum moisture content (OMC) and maximum dry density (MDD)); along with the unconfined compressive strength test (UCS). Different percentages of CWM were added to the soft soil (3, 6, 9, 12 and 15%) to produce various admixtures. Then the UCS test was carried out on specimens under different curing periods (zero, 7, 14, and 28 days) to find the optimum percentage of CWM. The optimum and other two percentages (either side of the optimum content) were used for FWM to evaluate the effect of the fineness of the WM on UCS of the stabilised soil. Results indicated that both types of the WM used in this study improved the physical properties of the soft soil where the index of plasticity (IP) was decreased significantly. IP was decreased from 21 to 13.64 and 13.10 with 12% of CWM and 15% of FWM respectively. The results of the unconfined compressive strength test indicated that 12% of CWM was the optimum and this percentage developed the UCS value from 202kPa to 500kPa for 28 days cured samples, which is equal, approximately 2.5 times the UCS value for untreated soil. Moreover, this percentage provided 1.4 times the value of UCS for stabilized soil-CWA by using FWM which recorded just under 700kPa after 28 days curing.
Abstract: Experimental investigations of the DC electric field effect on thermal decomposition of biomass, formation of the axial flow of volatiles (CO, H2, CxHy), mixing of volatiles with swirling airflow at low swirl intensity (S ≈ 0.2-0.35), their ignition and on formation of combustion dynamics are carried out with the aim to understand the mechanism of electric field influence on biomass gasification, combustion of volatiles and heat energy production. The DC electric field effect on combustion dynamics was studied by varying the positive bias voltage of the central electrode from 0.6 kV to 3 kV, whereas the ion current was limited to 2 mA. The results of experimental investigations confirm the field-enhanced biomass gasification with enhanced release of volatiles and the development of endothermic processes at the primary stage of thermochemical conversion of biomass determining the field-enhanced heat energy consumption with the correlating decrease of the flame temperature and heat energy production at this stage of flame formation. Further, the field-enhanced radial expansion of the flame reaction zone correlates with a more complete combustion of volatiles increasing the combustion efficiency by 3% and decreasing the mass fraction of CO, H2 and CxHy in the products, whereas by 10% increases the average volume fraction of CO2 and the heat energy production downstream the combustor increases by 5-10%
Abstract: This research aims to develop an algorithm to
generate a schedule of multiple cranes that will maximize load
throughputs in anodizing operation. The algorithm proposed utilizes
an enumerative strategy to search for constant time between
successive loads and crane covering range over baths. The computer
program developed is able to generate a near-optimal crane schedule
within reasonable times, i.e. within 10 minutes. Its results are
compared with existing solutions from an aluminum extrusion
industry. The program can be used to generate crane schedules for
mixed products, thus allowing mixed-model line balancing to
improve overall cycle times.
Abstract: This paper presents a computational study of steady
state three dimensional very high turbulent flow and heat transfer
characteristics in a constant temperature-surfaced circular duct fitted
with 900 hemispherical inline baffles. The computations are based on
realizable k-ɛ model with standard wall function considering the
finite volume method, and the SIMPLE algorithm has been
implemented. Computational Study are carried out for Reynolds
number, Re ranging from 80000 to 120000, Prandtl Number, Pr of
0.73, Pitch Ratios, PR of 1,2,3,4,5 based on the hydraulic diameter of
the channel, hydrodynamic entry length, thermal entry length and the
test section. Ansys Fluent 15.0 software has been used to solve the
flow field. Study reveals that circular pipe having baffles has a higher
Nusselt number and friction factor compared to the smooth circular
pipe without baffles. Maximum Nusselt number and friction factor
are obtained for the PR=5 and PR=1 respectively. Nusselt number
increases while pitch ratio increases in the range of study; however,
friction factor also decreases up to PR 3 and after which it becomes
almost constant up to PR 5. Thermal enhancement factor increases
with increasing pitch ratio but with slightly decreasing Reynolds
number in the range of study and becomes almost constant at higher
Reynolds number. The computational results reveal that optimum
thermal enhancement factor of 900 inline hemispherical baffle is
about 1.23 for pitch ratio 5 at Reynolds number 120000.It also shows
that the optimum pitch ratio for which the baffles can be installed in
such very high turbulent flows should be 5. Results show that pitch
ratio and Reynolds number play an important role on both fluid flow
and heat transfer characteristics.
Abstract: Experts, enterprises and operators expect that the
bandwidth request will increase up to rates of 100 to 1,000 Mbps
within several years. Therefore the most important question is which
technology shall satisfy the future consumer broadband demands.
Currently the consensus is, that the fiber technology has the best
technical characteristics to achieve such the high bandwidth rates.
But fiber technology is so far very cost-intensive and resource
consuming. To avoid these investments, operators are concentrating
to upgrade the existing copper and hybrid fiber coax infrastructures.
This work presents a comparison of the copper and fiber
technologies including an overview about the current German
broadband market. Both technologies are reviewed in the terms of
demand, willingness to pay and economic efficiency in connection
with the technical characteristics.
Abstract: The aim of this investigation is to elaborate nearinfrared
methods for testing and recognition of chemical components
and quality in “Pannon wheat” allied (i.e. true to variety or variety
identified) milling fractions as well as to develop spectroscopic
methods following the milling processes and evaluate the stability of
the milling technology by different types of milling products and
according to sampling times, respectively. These wheat categories
produced under industrial conditions where samples were collected
versus sampling time and maximum or minimum yields. The changes
of the main chemical components (such as starch, protein, lipid) and
physical properties of fractions (particle size) were analysed by
dispersive spectrophotometers using visible (VIS) and near-infrared
(NIR) regions of the electromagnetic radiation. Close correlation
were obtained between the data of spectroscopic measurement
techniques processed by various chemometric methods (e.g. principal
component analysis [PCA], cluster analysis [CA]) and operation
condition of milling technology. It is obvious that NIR methods are
able to detect the deviation of the yield parameters and differences of
the sampling times by a wide variety of fractions, respectively. NIR
technology can be used in the sensitive monitoring of milling
technology.
Abstract: A pilot field study was conducted at the Jagjeetpur
Municipal Sewage treatment plant situated in the Haridwar town in
Uttarakhand state, India. The objectives of the present study were to
study the effect of treated wastewater on the production of various
paddy varieties (Sharbati, PR-114, PB-1, Menaka, PB1121 and PB
1509) and the emission of GHG gases (CO2, CH4 and N2O) as
compared to the same varieties grown in the control plots irrigated
with fresh water. Of late, the concept of water footprint assessment
has emerged, which explains enumeration of various types of water
footprints of an agricultural entity from its production to processing
stages. Paddy, the most water demanding staple crop of Uttarakhand
state, displayed a high green water footprint value of 2474.12 m3/
Ton. Most of the wastewater irrigated varieties displayed up to 6%
increase in production, except Menaka and PB-1121, which showed a
reduction in production (6% and 3% respectively), due to pest and
insect infestation. The treated wastewater was observed to be rich in
Nitrogen (55.94 mg/ml Nitrate), Phosphorus (54.24 mg/ml) and
Potassium (9.78 mg/ml), thus rejuvenating the soil quality and not
requiring any external nutritional supplements. A Percentage increase
of GHG gases of irrigation with treated municipal wastewater as
compared to control plots was observed as 0.4% - 8.6% (CH4), 1.1%
- 9.2% (CO2), and 0.07% - 5.8% (N2O). The variety, Sharbati,
displayed maximum production (5.5 ton/ha) and emerged as the most
resistant variety against pests and insects. The emission values of
CH4, CO2 and N2O were 729.31 mg/m2/d, 322.10 mg/m2/d and
400.21 mg/m2/d in water stagnant condition.
This study highlighted a successful possibility of reuse of
wastewater for non-potable purposes offering the potential for
exploiting this resource that can replace or reduce the existing use of
fresh water sources in agriculture sector.
Abstract: Any signal transmitted over a channel is corrupted by noise and interference. A host of channel coding techniques has been proposed to alleviate the effect of such noise and interference. Among these Turbo codes are recommended, because of increased capacity at higher transmission rates and superior performance over convolutional codes. The multimedia elements which are associated with ample amount of data are best protected by Turbo codes. Turbo decoder employs Maximum A-posteriori Probability (MAP) and Soft Output Viterbi Decoding (SOVA) algorithms. Conventional Turbo coded systems employ Equal Error Protection (EEP) in which the protection of all the data in an information message is uniform. Some applications involve Unequal Error Protection (UEP) in which the level of protection is higher for important information bits than that of other bits. In this work, enhancement to the traditional Log MAP decoding algorithm is being done by using optimized scaling factors for both the decoders. The error correcting performance in presence of UEP in Additive White Gaussian Noise channel (AWGN) and Rayleigh fading are analyzed for the transmission of image with Discrete Cosine Transform (DCT) as source coding technique. This paper compares the performance of log MAP, Modified log MAP (MlogMAP) and Enhanced log MAP (ElogMAP) algorithms used for image transmission. The MlogMAP algorithm is found to be best for lower Eb/N0 values but for higher Eb/N0 ElogMAP performs better with optimized scaling factors. The performance comparison of AWGN with fading channel indicates the robustness of the proposed algorithm. According to the performance of three different message classes, class3 would be more protected than other two classes. From the performance analysis, it is observed that ElogMAP algorithm with UEP is best for transmission of an image compared to Log MAP and MlogMAP decoding algorithms.
Abstract: In order to determine the impact of thermo priming on germination of soybean seeds, an experiment was conducted as a completely randomized design with three replications. The factors of studied included different time thermo priming (control, 5 and 10 minutes) through the placing seeds were exposed to oven. The results showed that the effect of thermo priming was significant on germination percentage, seedling dry weight and seedling vigour in P ≤ 0.05. Mean comparison showed that the highest germination percentage (77%), seedling dry weight (1.39 g) and seedling vigour (107.03) were achieved by 10 minutes thermo priming.
Abstract: Complex lifting entry was selected for precise landing
performance during the Mars Science Laboratory entry. This study
aims to develop the three-dimensional numerical method for precise
computation and the surface panel method for rapid engineering
prediction. Detailed flow field analysis for Mars exploration mission
was performed by carrying on a series of fully three-dimensional
Navier-Stokes computations. The static aerodynamic performance was
then discussed, including the surface pressure, lift and drag coefficient,
lift-to-drag ratio with the numerical and engineering method.
Computation results shown that the shock layer is thin because of
lower effective specific heat ratio, and that calculated results from both
methods agree well with each other, and is consistent with the
reference data. Aerodynamic performance analysis shows that CG
location determines trim characteristics and pitch stability, and certain
radially and axially shift of the CG location can alter the capsule lifting
entry performance, which is of vital significance for the aerodynamic
configuration design and inner instrument layout of the Mars entry
capsule.
Abstract: Knowledge of bone mechanical properties is important
for bone substitutes design and fabrication, and more efficient
prostheses development. The aim of this study is to characterize the
viscoelastic behavior of bone specimens, through stress relaxation
and fatigue tests performed to trabecular bone samples from bovine
femoral heads. Relaxation tests consisted on preloading the samples
at five different magnitudes and evaluate them for 1020 seconds,
adjusting the results to a KWW mathematical model. Fatigue tests
consisted of 700 load cycles and analyze their status at the end of the
tests. As a conclusion we have that between relaxation stress and
each preload there is linear relation and for samples with initial
Young´s modulus greater than 1.5 GPa showed no effects due fatigue
test loading cycles.
Abstract: Biomass briquette gasification is regarded as a
promising route for efficient briquette use in energy generation, fuels
and other useful chemicals. However, previous research has been
focused on briquette gasification in fixed bed gasifiers such as
updraft and downdraft gasifiers. Fluidised bed gasifier has the
potential to be effectively sized to medium or large scale. This study
investigated the use of fuel briquettes produced from blends of rice
husks and corn cobs biomass, in a bubbling fluidised bed gasifier.
The study adopted a combination of numerical equations and Aspen
Plus simulation software, to predict the product gas (syngas)
composition base on briquette density and biomass composition
(blend ratio of rice husks to corn cobs). The Aspen Plus model was
based on an experimentally validated model from the literature. The
results based on a briquette size 32 mm diameter and relaxed density
range of 500 to 650kg/m3, indicated that fluidisation air required in
the gasifier increased with increase in briquette density, and the
fluidisation air showed to be the controlling factor compared with the
actual air required for gasification of the biomass briquettes. The
mass flowrate of CO2 in the predicted syngas composition increased
with an increase in air flow, in the gasifier, while CO decreased and
H2 was almost constant. The ratio of H2 to CO for various blends of
rice husks and corn cobs did not significantly change at the designed
process air, but a significant difference of 1.0 was observed between
10/90 and 90/10 % blend of rice husks and corn cobs.
Abstract: The research was conducted in order to determine the
organizational socialization levels of nurses working in hospitals in
the form of a descriptive study.
The research population was composed of nurses employed in
public and private sector hospitals in the province of Konya with 0-3
years of professional experience in the hospitals (N=1200); and the
sample was composed of 495 nurses that accepted to take part in the
study voluntarily. Statistical evaluation of data was conducted in
SPSS.16 software.
The results of the study revealed that the total score taken by
nurses at the organizational socialization scale was 262.95; and this
was close to the maximum score. Particularly the departmental
socialization sub-dimension proved to be higher in comparison to the
other two dimensions (organization socialization and task
socialization). Statistically meaningful differences were found in the
levels of organization socialization in relation to the status of
organizational orientation training, level of education and age group.
Abstract: Whey is the lactose rich by-product of the dairy
industry, having good amount of nutrient reservoir. Most abundant
nutrients are lactose, soluble proteins, lipids and mineral salts.
Disposing of whey by most of milk plants which do not have proper
pre-treatment system is the major issue. As a result of which, there
can be significant loss of potential food and energy source. Thus,
whey has been explored as the substrate for the synthesis of different
value added products such as enzymes. β-galactosidase is one of the
important enzymes and has become the major focus of research due
to its ability to catalyze both hydrolytic as well as
transgalactosylation reaction simultaneously. The enzyme is widely
used in dairy industry as it catalyzes the transformation of lactose to
glucose and galactose, making it suitable for the lactose intolerant
people. The enzyme is intracellular in both bacteria and yeast,
whereas for molds, it has an extracellular location. The present work
was carried to utilize the whey for the production of β-galactosidase
enzyme using both yeast and fungal cultures. The yeast isolate
Kluyveromyces marxianus WIG2 and various fungal strains have
been used in the present study. Different disruption techniques have
also been investigated for the extraction of the enzyme produced
intracellularly from yeast cells. Among the different methods tested
for the disruption of yeast cells, SDS-chloroform showed the
maximum β-galactosidase activity. In case of the tested fungal
cultures, Aureobasidium pullulans NCIM 1050 was observed to be
the maximum extracellular enzyme producer.