Abstract: The Kowsar dam supply water for different usages
such as drinking, industrial, agricultural and aquaculture farms
usages and located next to the city of Dehdashat in Kohgiluye and
Boyerahmad province in southern Iran. There are some towns and
villages on the Kowsar dam watersheds, which Dehdasht and
Choram are the most important and populated cities in this area. The
study was undertaken to assess the status of water quality in the
urban areas of the Kowsar dam. A total of 28 water samples were
collected from 6 stations on surface water and 1 station from
groundwater on the watershed of the Kowsar dam. All the samples
were analyzed for Cd concentration using standard procedures. The
results were compared with other national and international
standards. Among the analyzed samples, as the maximum value of
cadmium (1.131 μg/L) was observed on the station 2 at the winter
2009, all the samples analyzed were within the maximum admissible
limits by the United States Environmental Protection Agency, EU,
WHO, New Zealand , Australian, Iranian, and the Indian standards.
In general results of the present study have shown that Cd mean
values of stations No. 4, 1 and 2 with 0.5135, 0.0.4733 and 0.4573
μg/L respectively are higher than the other stations . Although Cd
level of all samples and stations have had normal values but this is
an indication of pollution potential and hazards because of human
activity and waste water of towns in the areas, which can effect on
human health implications in future. This research, therefore,
recommends the government and other responsible authorities to take
suitable improving measures in the Kowsar dam watershed-s.
Abstract: Data stream analysis is the process of computing
various summaries and derived values from large amounts of data
which are continuously generated at a rapid rate. The nature of a
stream does not allow a revisit on each data element. Furthermore,
data processing must be fast to produce timely analysis results. These
requirements impose constraints on the design of the algorithms to
balance correctness against timely responses. Several techniques
have been proposed over the past few years to address these
challenges. These techniques can be categorized as either dataoriented
or task-oriented. The data-oriented approach analyzes a
subset of data or a smaller transformed representation, whereas taskoriented
scheme solves the problem directly via approximation
techniques. We propose a hybrid approach to tackle the data stream
analysis problem. The data stream has been both statistically
transformed to a smaller size and computationally approximated its
characteristics. We adopt a Monte Carlo method in the approximation
step. The data reduction has been performed horizontally and
vertically through our EMR sampling method. The proposed method
is analyzed by a series of experiments. We apply our algorithm on
clustering and classification tasks to evaluate the utility of our
approach.
Abstract: Sorting appears the most attention among all computational tasks over the past years because sorted data is at the heart of many computations. Sorting is of additional importance to parallel computing because of its close relation to the task of routing data among processes, which is an essential part of many parallel algorithms. Many parallel sorting algorithms have been investigated for a variety of parallel computer architectures. In this paper, three parallel sorting algorithms have been implemented and compared in terms of their overall execution time. The algorithms implemented are the odd-even transposition sort, parallel merge sort and parallel rank sort. Cluster of Workstations or Windows Compute Cluster has been used to compare the algorithms implemented. The C# programming language is used to develop the sorting algorithms. The MPI (Message Passing Interface) library has been selected to establish the communication and synchronization between processors. The time complexity for each parallel sorting algorithm will also be mentioned and analyzed.
Abstract: A Rotary Disc Contactor with inner diameter of
9.1cm and maximum operating height of 40cm has been used to
investigate break up phenomenon. Water-Toluene, Water as
continuous phase and Toluene as dispersed phase, was selected as
chemical system in the experiments. The mentioned chemical system
has high interfacial tension so it was possible to form big drops
which permit accurate investigation on break up phenomenon as well
as the first and second critical rotor speeds.
In this study, Break up phenomenon has been studied as a function
of mother drop size, rotor speed and continuous phase height. Further
more; the effects of mother drop size and continuous phase height on
the first and second critical rotor speeds were investigated. Finally,
two modified correlations were proposed to estimate the first and
second critical speeds.
Abstract: Over the past years, the EMCCD has had a profound
influence on photon starved imaging applications relying on its unique
multiplication register based on the impact ionization effect in the
silicon. High signal-to-noise ratio (SNR) means high image quality.
Thus, SNR improvement is important for the EMCCD. This work
analyzes the SNR performance of an EMCCD with gain off and on. In
each mode, simplified SNR models are established for different
integration times. The SNR curves are divided into readout noise (or
CIC) region and shot noise region by integration time. Theoretical
SNR values comparing long frame integration and frame adding in
each region are presented and discussed to figure out which method is
more effective. In order to further improve the SNR performance,
pixel binning is introduced into the EMCCD. The results show that
pixel binning does obviously improve the SNR performance, but at the
expensive of the spatial resolution.
Abstract: The regional innovative competitiveness is an integrating characteristic of the innovative sphere of the region. It depends on a big variety of different parameters connected with all kinds of economic entities- activities. But management parameters shouldn't be irregular, so in order to avoid it, an institutional system should be formed. This system should carry out strategic management of factors having the greatest influence on the region's innovative development. This article is devoted to different aspects of organization of the region's development institutional mechanism, which is based on management of regional innovative competitiveness parameters. The base of the analysis is innovatively-active Russian regions which were compared according to the level of the innovative competitiveness. After that the most important parameters of successful innovative development of the region were revealed with the help of the correlation-regression analysis. The results of the research could be used for investigation of the region's innovative policy.
Abstract: This paper aims to argue that religion and Faith-based
Organizations (FBOs) contribute to building democratic process
through the provision of education in Sierra Leone. Sierra Leone
experienced a civil war from 1991 to 2002 and about 70 percent of the
population lives in poverty. While the government has been in the
process of rebuilding the nation, many forms of Civil Society
Organizations (CSOs), including FBOs, have played a significant role
in promoting social development. Education plays an important role in
supporting people-s democratic movements through knowledge
acquisition, spiritual enlightenment and empowerment. This paper
discusses religious tolerance in Sierra Leone and how FBOs have
contributed to the provision of primary education in Sierra Leone. This
study is based on the author-s field research, which involved
interviews with teachers and development stakeholders, notably
government officials, Non-governmental Organizations (NGOs) and
FBOs, as well as questionnaires completed by pupils, parents and
teachers.
Abstract: The draw solute separation process in Forward
Osmosis desalination was simulated in Aspen Plus chemical process
modeling software, to estimate the energy consumption and compare
it with other desalination processes, mainly the Reverse Osmosis
process which is currently most prevalent. The electrolytic chemistry
for the system was retrieved using the Elec – NRTL property method
in the Aspen Plus database. Electrical equivalent of energy required
in the Forward Osmosis desalination technique was estimated and
compared with the prevalent desalination techniques.
Abstract: In this paper the vibration behaviors of a structure equipped with a tuned liquid column damper (TLCD) under a harmonic type of earthquake loading are studied. However, due to inherent nonlinear liquid damping, it is no doubt that a great deal of computational effort is required to search the optimum parameters of the TLCD, numerically. Therefore by linearization the equation of motion of the single degree of freedom structure equipped with the TLCD, the closed form solutions of the TLCD-structure system are derived. To find the reliability of the analytical method, the results have been compared with other researcher and have good agreement. Further, the effects of optimal design parameters such as length ratio and mass ratio on the performance of the TLCD for controlling the responses of a structure are investigated by using the harmonic type of earthquake excitation. Finally, the Citicorp Center which has a very flexible structure is used as an example to illustrate the design procedure for the TLCD under the earthquake excitation.
Abstract: Wavelet transform provides several important
characteristics which can be used in a texture analysis and
classification. In this work, an efficient texture classification method,
which combines concepts from wavelet and co-occurrence matrices,
is presented. An Euclidian distance classifier is used to evaluate the
various methods of classification. A comparative study is essential to
determine the ideal method. Using this conjecture, we developed a
novel feature set for texture classification and demonstrate its
effectiveness
Abstract: This paper deals with the design, development & implementation of a temperature sensor using zigbee. The main aim of the work undertaken in this paper is to sense the temperature and to display the result on the LCD using the zigbee technology. ZigBee operates in the industrial, scientific and medical (ISM) radio bands; 868 MHz in Europe, 915 MHz in the USA and 2.4 GHz in most jurisdictions worldwide. The technology is intended to be simpler and cheaper than other WPANs such as Bluetooth. The most capable ZigBee node type is said to require only about 10 % of the software of a typical Bluetooth or Wireless Internet node, while the simplest nodes are about 2 %. However, actual code sizes are much higher, more like 50 % of the Bluetooth code size. ZigBee chip vendors have announced 128-kilobyte devices. In this work undertaken in the design & development of the temperature sensor, it senses the temperature and after amplification is then fed to the micro controller, this is then connected to the zigbee module, which transmits the data and at the other end the zigbee reads the data and displays on to the LCD. The software developed is highly accurate and works at a very high speed. The method developed shows the effectiveness of the scheme employed.
Abstract: In wireless sensor network (WSN) the use of mobile
sink has been attracting more attention in recent times. Mobile sinks
are more effective means of balancing load, reducing hotspot
problem and elongating network lifetime. The sensor nodes in WSN
have limited power supply, computational capability and storage and
therefore for continuous data delivery reliability becomes high
priority in these networks. In this paper, we propose a Reliable
Energy-efficient Data Dissemination (REDD) scheme for WSNs with
multiple mobile sinks. In this strategy, sink first determines the
location of source and then directly communicates with the source
using geographical forwarding. Every forwarding node (FN) creates a
local zone comprising some sensor nodes that can act as
representative of FN when it fails. Analytical and simulation study
reveals significant improvement in energy conservation and reliable
data delivery in comparison to existing schemes.
Abstract: In this paper, supply policy and procurement of
shared resources in some kinds of concurrent construction projects
are investigated. This could be oriented to the problems of holding
construction companies who involve in different projects
concurrently and they have to supply limited resources to several
projects as well as prevent delays to any project. Limits on
transportation vehicles and storage facilities for potential
construction materials and also the available resources (such as cash
or manpower) are some of the examples which affect considerably on
management of all projects over all. The research includes
investigation of some real multi-storey buildings during their
execution periods and surveying the history of the activities. It is
shown that the common resource demand variation curve of the
projects may be expanded or displaced to achieve an optimum
distribution scheme. Of course, it may cause some delay to some
projects, but it has minimum influence on whole execution period of
all projects and its influence on procurement cost of the projects is
considerable. These observations on investigation of some
multistorey building which are built in Iran will be presented in this
paper.
Abstract: Real-time 3D applications have to guarantee
interactive rendering speed. There is a restriction for the number of
polygons which is rendered due to performance of a graphics hardware
or graphics algorithms. Generally, the rendering performance will be
drastically increased when handling only the dynamic 3d models,
which is much fewer than the static ones. Since shapes and colors of
the static objects don-t change when the viewing direction is fixed, the
information can be reused. We render huge amounts of polygon those
cannot handled by conventional rendering techniques in real-time by
using a static object image and merging it with rendering result of the
dynamic objects. The performance must be decreased as a
consequence of updating the static object image including removing
an static object that starts to move, re-rending the other static objects
being overlapped by the moving ones. Based on visibility of the object
beginning to move, we can skip the updating process. As a result, we
enhance rendering performance and reduce differences of rendering
speed between each frame. Proposed method renders total
200,000,000 polygons that consist of 500,000 dynamic polygons and
the rest are static polygons in about 100 frames per second.
Abstract: The dome with ribs and rings, which covers the
ROMEXPO pavilion from Bucharest, was designed after the collapse
of the single layer reticulated dome. In this paper, it was made the
checking of the structure, under the dynamic loads with three
recorded accelerograms calibrated according to Romanian seismic
design code P100-1/2006. Under the action the dynamic loadings, it
was made a time-history analysis to determine the zones where the
plastic hinges appear, at what accelerations and their position on the
structure. The studied dome is formed by 32 spatial semi arches and
three rings: one circular ring located at the top of the dome and
another two rings, design as trusses, the first near the supports and the
second as an intermediate rings above the skylights. Above the
skylights up to the top, the dome is tight together with purlins and
bracings.
Abstract: In this paper, the modelling and design of artificial neural network architecture for load forecasting purposes is investigated. The primary pre-requisite for power system planning is to arrive at realistic estimates of future demand of power, which is known as Load Forecasting. Short Term Load Forecasting (STLF) helps in determining the economic, reliable and secure operating strategies for power system. The dependence of load on several factors makes the load forecasting a very challenging job. An over estimation of the load may cause premature investment and unnecessary blocking of the capital where as under estimation of load may result in shortage of equipment and circuits. It is always better to plan the system for the load slightly higher than expected one so that no exigency may arise. In this paper, a load-forecasting model is proposed using a multilayer neural network with an appropriately modified back propagation learning algorithm. Once the neural network model is designed and trained, it can forecast the load of the power system 24 hours ahead on daily basis and can also forecast the cumulative load on daily basis. The real load data that is used for the Artificial Neural Network training was taken from LDC, Gujarat Electricity Board, Jambuva, Gujarat, India. The results show that the load forecasting of the ANN model follows the actual load pattern more accurately throughout the forecasted period.
Abstract: In this paper, we propose a novel adaptive voltage control strategy for boost converter via Inverse LQ Servo-Control. Our presented strategy is based on an analytical formula of Inverse Linear Quadratic (ILQ) design method, which is not necessary to solve Riccati’s equation directly. The optimal and adaptive controller of the voltage control system is designed. The stability and the robust control are analyzed. Whereas, we can get the analytical solution for the optimal and robust voltage control is achieved through the natural angular velocity within a single parameter and we can change the responses easily via the ILQ control theory. Our method provides effective results as the stable responses and the response times are not drifted even if the condition is changed widely.
Abstract: A geothermal power plant multiple simulator for
operators training is presented. The simulator is designed to be
installed in a wireless local area network and has a capacity to train
one to six operators simultaneously, each one with an independent
simulation session. The sessions must be supervised only by one
instructor. The main parts of this multiple simulator are: instructor
and operator-s stations. On the instructor station, the instructor
controls the simulation sessions, establishes training exercises and
supervises each power plant operator in individual way. This station
is hosted in a Main Personal Computer (NS) and its main functions
are: to set initial conditions, snapshots, malfunctions or faults,
monitoring trends, and process and soft-panel diagrams. On the other
hand the operators carry out their actions over the power plant
simulated on the operator-s stations; each one is also hosted in a PC.
The main software of instructor and operator-s stations are executed
on the same NS and displayed in PCs through graphical Interactive
Process Diagrams (IDP). The geothermal multiple simulator has been
installed in the Geothermal Simulation Training Center (GSTC) of
the Comisi├│n Federal de Electricidad, (Federal Commission of
Electricity, CFE), Mexico, and is being utilized as a part of the
training courses for geothermal power plant operators.
Abstract: The inability to implement the principles of good
corporate governance (GCG) as demonstrated in the surveys is due to
a number of constraints which can be classified into three; namely internal constraints, external constraints, and constraints coming
from the structure of ownership. The issues in the internal constraints
mentioned are related to the function of several elements of the company. As a business organization, corporation is unable to
achieve its goal to successfully implement GCG principles since it is
not support by its internal elements- functions. Two of several numbers of internal elements of a company are ethical work climate
and leadership style of the top management.
To prove the correlation between internal function of organization
(in this case ethical work climate and transformational leadership)
and the successful implementation of GCG principles, this study
proposes two hypotheses to be empirically tested on thirty surveyed organizations; eleven of which are state-owned companies and
nineteen are private companies. These thirty corporations are listed in
the Jakarta Stock Exchange. All state-owned companies in the
samples are those which have been privatized.
The research showed that internal function of organization give
support to the successful implementation of GCG principle. In this
research we can prove that : (i) ethical work climate has positive
significance of correlation with the successful implementation of
social awareness principle (one of principles on GCG) and, (ii) only
at the state-owned companies, transformational leadership have
positive significance effect to forming the ethical work climate.
Abstract: The evaluation of non-conventional water resources
on seed germination and seedling growth performance at early
growth stages is still in progress especially in forage crops. This
study was designed to test the effect of four types of water qualities
(treated wastewater (TWW), industrial water (IW), grey water (GW),
and Distilled water (DW)) on germination and early seedling vigor of
Leucaena leucocephala. The results showed that the germination
was not significantly affected by the different water qualities. Seed
germination reached maximum after 17, 14, 14, and 21 days under
GW, IW, TWW, and DW treatments, respectively. The highest mean
of shoot length was scored under the GW treatment. And, the highest
mean of root length was scored under DW which was not significant
from GW treatment. The means of shoot fresh was the highest under
the TWW. The means of root fresh weight was not significantly
different from each other's under different treatments. The growth
performance was in progress with no mortality during 21 days of
growth. Thus, the best non-conventional water qualities alternatives
based on the cleanness, nutrients, and toxicity are the GW, TWW and
IW, respectively.