Abstract: This paper presents two simplified models to
determine nodal voltages in power distribution networks. These
models allow estimating the impact of the installation of reactive
power compensations equipments like fixed or switched capacitor
banks. The procedure used to develop the models is similar to the
procedure used to develop linear power flow models of transmission
lines, which have been widely used in optimization problems of
operation planning and system expansion. The steady state non-linear
load flow equations are approximated by linear equations relating the
voltage amplitude and currents. The approximations of the linear
equations are based on the high relationship between line resistance
and line reactance (ratio R/X), which is valid for power distribution
networks. The performance and accuracy of the models are evaluated
through comparisons with the exact results obtained from the
solution of the load flow using two test networks: a hypothetical
network with 23 nodes and a real network with 217 nodes.
Abstract: As a result of urbanization, the unpredictable growth of industry and transport, production of chemicals, military activities, etc. the concentration of anthropogenic toxicants spread in nature exceeds all the permissible standards. Most dangerous among these contaminants are organic compounds having great persistence, bioaccumulation, and toxicity along with our awareness of their prominent occurrence in the environment and food chain. Among natural ecological tools, plants still occupying above 40% of the world land, until recently, were considered as organisms having only a limited ecological potential, accumulating in plant biomass and partially volatilizing contaminants of different structure. However, analysis of experimental data of the last two decades revealed the essential role of plants in environment remediation due to ability to carry out intracellular degradation processes leading to partial or complete decomposition of carbon skeleton of different structure contaminants. Though, phytoremediation technologies still are in research and development, their various applications have been successfully used. The paper aims to analyze mechanisms of organic contaminants uptake and detoxification in plants, being the less studied issue in evaluation and exploration of plants potential for environment remediation.
Abstract: In some real applications of Statistical Process Control
it is necessary to design a control chart to not detect small process
shifts, but keeping a good performance to detect moderate and large
shifts in the quality. In this work we develop a new quality control
chart, the synthetic T2 control chart, that can be designed to cope with
this objective. A multi-objective optimization is carried out employing
Genetic Algorithms, finding the Pareto-optimal front of
non-dominated solutions for this optimization problem.
Abstract: A 10bit, 40 MSps, sample and hold, implemented in 0.18-μm CMOS technology with 3.3V supply, is presented for application in the front-end stage of an analog-to-digital converter. Topology selection, biasing, compensation and common mode feedback are discussed. Cascode technique has been used to increase the dc gain. The proposed opamp provides 149MHz unity-gain bandwidth (wu), 80 degree phase margin and a differential peak to peak output swing more than 2.5v. The circuit has 55db Total Harmonic Distortion (THD), using the improved fully differential two stage operational amplifier of 91.7dB gain. The power dissipation of the designed sample and hold is 4.7mw. The designed system demonstrates relatively suitable response in different process, temperature and supply corners (PVT corners).
Abstract: This paper describes a CMOS four-quadrant
multiplier intended for use in the front-end receiver by utilizing the
square-law characteristic of the MOS transistor in the saturation
region. The circuit is based on 0.35 um CMOS technology simulated
using HSPICE software. The mixer has a third-order inter the power
consumption is 271uW from a single 1.2V power supply. One of the
features of the proposed design is using two MOS transistors
limitation to reduce the supply voltage, which leads to reduce the
power consumption. This technique provides a GHz bandwidth
response and low power consumption.
Abstract: Nowadays, engineering ceramics have significant
applications in different industries such as; automotive, aerospace,
electrical, electronics and even martial industries due to their
attractive physical and mechanical properties like very high hardness
and strength at elevated temperatures, chemical stability, low friction
and high wear resistance. However, these interesting properties plus
low heat conductivity make their machining processes too hard,
costly and time consuming. Many attempts have been made in order
to make the grinding process of engineering ceramics easier and
many scientists have tried to find proper techniques to economize
ceramics' machining processes. This paper proposes a new diamond
plunge grinding technique using ultrasonic vibration for grinding
Alumina ceramic (Al2O3). For this purpose, a set of laboratory
equipments have been designed and simulated using Finite Element
Method (FEM) and constructed in order to be used in various
measurements. The results obtained have been compared with the
conventional plunge grinding process without ultrasonic vibration
and indicated that the surface roughness and fracture strength
improved and the grinding forces decreased.
Abstract: High speed networks provide realtime variable bit rate
service with diversified traffic flow characteristics and quality
requirements. The variable bit rate traffic has stringent delay and
packet loss requirements. The burstiness of the correlated traffic
makes dynamic buffer management highly desirable to satisfy the
Quality of Service (QoS) requirements. This paper presents an
algorithm for optimization of adaptive buffer allocation scheme for
traffic based on loss of consecutive packets in data-stream and buffer
occupancy level. Buffer is designed to allow the input traffic to be
partitioned into different priority classes and based on the input
traffic behavior it controls the threshold dynamically. This algorithm
allows input packets to enter into buffer if its occupancy level is less
than the threshold value for priority of that packet. The threshold is
dynamically varied in runtime based on packet loss behavior. The
simulation is run for two priority classes of the input traffic –
realtime and non-realtime classes. The simulation results show that
Adaptive Partial Buffer Sharing (ADPBS) has better performance
than Static Partial Buffer Sharing (SPBS) and First In First Out
(FIFO) queue under the same traffic conditions.
Abstract: Network layer multicast, i.e. IP multicast, even after
many years of research, development and standardization, is not
deployed in large scale due to both technical (e.g. upgrading of
routers) and political (e.g. policy making and negotiation) issues.
Researchers looked for alternatives and proposed application/overlay
multicast where multicast functions are handled by end hosts, not
network layer routers. Member hosts wishing to receive multicast
data form a multicast delivery tree. The intermediate hosts in the tree
act as routers also, i.e. they forward data to the lower hosts in the
tree. Unlike IP multicast, where a router cannot leave the tree until all
members below it leave, in overlay multicast any member can leave
the tree at any time thus disjoining the tree and disrupting the data
dissemination. All the disrupted hosts have to rejoin the tree. This
characteristic of the overlay multicast causes multicast tree unstable,
data loss and rejoin overhead. In this paper, we propose that each node
sets its leaving time from the tree and sends join request to a number
of nodes in the tree. The nodes in the tree will reject the request if
their leaving time is earlier than the requesting node otherwise they
will accept the request. The node can join at one of the accepting
nodes. This makes the tree more stable as the nodes will join the tree
according to their leaving time, earliest leaving time node being at the
leaf of the tree. Some intermediate nodes may not follow their leaving
time and leave earlier than their leaving time thus disrupting the tree.
For this, we propose a proactive recovery mechanism so that disrupted
nodes can rejoin the tree at predetermined nodes immediately. We
have shown by simulation that there is less overhead when joining
the multicast tree and the recovery time of the disrupted nodes is
much less than the previous works. Keywords
Abstract: This paper presents the significant factor and give
some suggestion that should know before design. The main objective of this paper is guide the first step for someone who attends to design of grounding system before study in details later. The overview of
grounding system can protect damage from fault such as can save a human life and power system equipment. The unsafe conditions have
three cases. Case 1) maximum touch voltage exceeds the safety
criteria. In this case, the conductor compression ratio of the ground gird should be first adjusted to have optimal spacing of ground grid
conductors. If it still over limit, earth resistivity should be consider afterward. Case 2) maximum step voltage exceeds the safety criteria.
In this case, increasing the number of ground grid conductors around
the boundary can solve this problem. Case 3) both of maximum touch
and step voltage exceed the safety criteria. In this case, follow the solutions explained in case 1 and case 2. Another suggestion, vary depth of ground grid until maximum step and touch voltage do not
exceed the safety criteria.
Abstract: In this paper, a tooth shape optimization method for
cogging torque reduction in Permanent Magnet (PM) motors is
developed by using the Reduced Basis Technique (RBT) coupled by
Finite Element Analysis (FEA) and Design of Experiments (DOE)
methods. The primary objective of the method is to reduce the
enormous number of design variables required to define the tooth
shape. RBT is a weighted combination of several basis shapes. The
aim of the method is to find the best combination using the weights
for each tooth shape as the design variables. A multi-level design
process is developed to find suitable basis shapes or trial shapes at
each level that can be used in the reduced basis technique. Each level
is treated as a separated optimization problem until the required
objective – minimum cogging torque – is achieved. The process is
started with geometrically simple basis shapes that are defined by
their shape co-ordinates. The experimental design of Taguchi method
is used to build the approximation model and to perform
optimization. This method is demonstrated on the tooth shape
optimization of a 8-poles/12-slots PM motor.
Abstract: The objective of the present study was to evaluate the
potential of hollow microneedles for enhancing the transdermal
delivery of Bovine Serum Albumin (MW~66,000 Da)-Fluorescein
Isothiocyanate (BSA-FITC) conjugate, a hydrophilic large molecular
compound. Moreover, the effect of different formulations was
evaluated. The series of binary mixtures composed of propylene
glycol (PG) and pH 7.4 phosphate buffer solution (PBS) was
prepared and used as a medium for BSA-FITC. The results showed
that there was no permeation of BSA-FITC solution across the
neonatal porcine skin without using hollow microneedles, whereas
the cumulative amount of BSA-FITC released at 8 h through the
neonatal porcine skin was about 60-70% when using hollow
microneedles. Furthermore, the results demonstrated that the higher
volume of PG in binary mixtures injected, the lower cumulative
amount of BSA-FITC released and release rate of BSA-FITC from
skin. These release profiles of BSA-FITC in binary mixtures were
expressed by Fick-s law of diffusion. These results suggest the
utilization of hollow microneedle to enhance transdermal delivery of
protein and provide useful information for designing an effective
hollow microneedle system.
Abstract: We propose that Virtual Learning Environments (VLEs) should be designed by taking into account the characteristics, the special needs and the specific operating rules of the academic institutions in which they are employed. In this context, we describe a VLE module that extends the support of the organization and delivery of course material by including administration activities related to the various stages of teaching. These include the co-ordination, collaboration and monitoring of the course material development process and institution-specific course material delivery modes. Our specialized module, which enhances VLE capabilities by Helping Educators and Learners through a Laboratory Assistance System, is willing to assist the Greek tertiary technological sector, which includes Technological Educational Institutes (T.E.I.).
Abstract: In this paper a new approach to face recognition is
presented that achieves double dimension reduction, making the
system computationally efficient with better recognition results and
out perform common DCT technique of face recognition. In pattern
recognition techniques, discriminative information of image
increases with increase in resolution to a certain extent, consequently
face recognition results change with change in face image resolution
and provide optimal results when arriving at a certain resolution
level. In the proposed model of face recognition, initially image
decimation algorithm is applied on face image for dimension
reduction to a certain resolution level which provides best
recognition results. Due to increased computational speed and feature
extraction potential of Discrete Cosine Transform (DCT), it is
applied on face image. A subset of coefficients of DCT from low to
mid frequencies that represent the face adequately and provides best
recognition results is retained. A tradeoff between decimation factor,
number of DCT coefficients retained and recognition rate with
minimum computation is obtained. Preprocessing of the image is
carried out to increase its robustness against variations in poses and
illumination level. This new model has been tested on different
databases which include ORL , Yale and EME color database.
Abstract: Supply chain networks are frequently hit by
unplanned events which lead to disruptions and cause operational and
financial consequences. It is neither possible to avoid disruption risk
entirely, nor are network members able to prepare for every possible
disruptive event. Therefore a continuity planning should be set up
which supports effective operational responses in supply chain
networks in times of emergencies. In this research network related
degrees of freedom which determine the options for responsive
actions are derived from interview data. The findings are further
embedded into a common risk management process. The paper
provides support for researchers and practitioners to identify the
network related options for responsive actions and to determine the
need for improving the reaction capabilities.
Abstract: Finite impulse response (FIR) filters have the advantage of linear phase, guaranteed stability, fewer finite precision errors, and efficient implementation. In contrast, they have a major disadvantage of high order need (more coefficients) than IIR counterpart with comparable performance. The high order demand imposes more hardware requirements, arithmetic operations, area usage, and power consumption when designing and fabricating the filter. Therefore, minimizing or reducing these parameters, is a major goal or target in digital filter design task. This paper presents an algorithm proposed for modifying values and the number of non-zero coefficients used to represent the FIR digital pulse shaping filter response. With this algorithm, the FIR filter frequency and phase response can be represented with a minimum number of non-zero coefficients. Therefore, reducing the arithmetic complexity needed to get the filter output. Consequently, the system characteristic i.e. power consumption, area usage, and processing time are also reduced. The proposed algorithm is more powerful when integrated with multiplierless algorithms such as distributed arithmetic (DA) in designing high order digital FIR filters. Here the DA usage eliminates the need for multipliers when implementing the multiply and accumulate unit (MAC) and the proposed algorithm will reduce the number of adders and addition operations needed through the minimization of the non-zero values coefficients to get the filter output.
Abstract: The bit error rate (BER) performance for ultra-wide
band (UWB) indoor communication with impact of metallic furniture
is investigated. The impulse responses of different indoor
environments for any transmitter and receiver location are computed
by shooting and bouncing ray/image and inverse Fourier transform
techniques. By using the impulse responses of these multipath
channels, the BER performance for binary pulse amplitude
modulation (BPAM) impulse radio UWB communication system are
calculated. Numerical results have shown that the multi-path effect
by the metallic cabinets is an important factor for BER performance.
Also the outage probability for the UWB multipath environment with
metallic cabinets is more serious (about 18%) than with wooden
cabinets. Finally, it is worth noting that in these cases the present
work provides not only comparative information but also quantitative
information on the performance reduction.
Abstract: In order to perform on-line measuring and detection
of PD signals, a total solution composing of an HFCT, A/D
converter and a complete software package is proposed. The
software package includes compensation of HFCT contribution,
filtering and noise reduction using wavelet transform and soft
calibration routines. The results have shown good performance and
high accuracy.
Abstract: A satured liquid is warmed until boiling in a parallelepipedic boiler. The heat is supplied in a liquid through the horizontal bottom of the boiler, the other walls being adiabatic. During the process of boiling, the liquid evaporates through its free surface by deforming it. This surface which subdivides the boiler into two regions occupied on both sides by the boiled liquid (broth) and its vapor which surmounts it. The broth occupying the region and its vapor the superior region. A two- fluids model is used to describe the dynamics of the broth, its vapor and their interface. In this model, the broth is treated as a monophasic fluid (homogeneous model) and form with its vapor adiphasic pseudo fluid (two-fluid model). Furthermore, the interface is treated as a zone of mixture characterized by superficial void fraction noted α* . The aim of this article is to describe the dynamics of the interface between the boiled fluid and its vapor within a boiler. The resolution of the problem allowed us to show the evolution of the broth and the level of the liquid.
Abstract: Influence of octane and benzene on plant cell
ultrastructure and enzymes of basic metabolism, such as nitrogen
assimilation and energy generation have been studied. Different
plants: perennial ryegrass (Lolium perenne) and alfalfa (Medicago
sativa); crops- maize (Zea mays L.) and bean (Phaseolus vulgaris);
shrubs – privet (Ligustrum sempervirens) and trifoliate orange
(Poncirus trifoliate); trees - poplar (Populus deltoides) and white
mulberry (Morus alba L.) were exposed to hydrocarbons of different
concentrations (1, 10 and 100 mM). Destructive changes in bean and
maize leaves cells ultrastructure under the influence of benzene
vapour were revealed at the level of photosynthetic and energy
generation subcellular organells. Different deviations at the level of
subcellular organelles structure and distribution were observed in
alfalfa and ryegrass root cells under the influence of benzene and
octane, absorbed through roots. The level of destructive changes is
concentration dependent. Benzene at low 1 and 10 mM concentration
caused the increase in glutamate dehydrogenase (GDH) activity in
maize roots and leaves and in poplar and mulberry shoots, though to
higher extent in case of lower, 1mM concentration. The induction
was more intensive in plant roots. The highest tested 100mM
concentration of benzene was inhibitory to the enzyme in all plants.
Octane caused induction of GDH in all grassy plants at all tested
concentrations; however the rate of induction decreased parallel to
increase of the hydrocarbon concentration. Octane at concentration 1
mM caused induction of GDH in privet, trifoliate and white mulberry
shoots. The highest, 100mM octane was characterized by inhibitory
effect to GDH activity in all plants. Octane had inductive effect on
malate dehydrogenase in almost all plants and tested concentrations,
indicating the intensification of Trycarboxylic Acid Cycle.
The data could be suggested for elaboration of criteria for plant
selection for phytoremediation of oil hydrocarbons contaminated
soils.
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production