Abstract: An effort for the detection of damages in the
reinforcement bars of reinforced concrete members using PZTs is
presented. The damage can be the result of excessive elongation of
the steel bar due to steel yielding or due to local steel corrosion. In
both cases the damage is simulated by considering reduced diameter
of the rebar along the damaged part of its length. An integration
approach based on both electromechanical admittance methodology
and guided wave propagation technique is used to evaluate the
artificial damage on the examined longitudinal steel bar. Two
actuator PZTs and a sensor PZT are considered to be bonded on the
examined steel bar. The admittance of the Sensor PZT is calculated
using COMSOL 3.4a. Fast Furrier Transformation for a better
evaluation of the results is employed. An effort for the quantification
of the damage detection using the root mean square deviation
(RMSD) between the healthy condition and damage state of the
sensor PZT is attempted. The numerical value of the RSMD yields a
level for the difference between the healthy and the damaged
admittance computation indicating this way the presence of damage
in the structure. Experimental measurements are also presented.
Abstract: Determination of optimal parameters of a passive
control system device is the primary objective of this study.
Expanding upon the use of control devices in wind and earthquake
hazard reduction has led to development of various control systems.
The advantage of non-linearity characteristics in a passive control
device and the optimal control method using LQR algorithm are
explained in this study. Finally, this paper introduces a simple
approach to determine optimum parameters of a nonlinear viscous
damper for vibration control of structures. A MATLAB program is
used to produce the dynamic motion of the structure considering the
stiffness matrix of the SDOF frame and the non-linear damping
effect. This study concluded that the proposed system (variable
damping system) has better performance in system response control
than a linear damping system. Also, according to the energy
dissipation graph, the total energy loss is greater in non-linear
damping system than other systems.
Abstract: Asymmetric incremental sheet forming (AISF) could significantly reduce costs incurred by the fabrication of complex industrial components with a minimal environmental impact. The AISF experiments were carried out on commercially pure titanium (Ti-Gr2), Timetal (15-3-3-3) alloy, and Ti-6Al-4V (Ti-Gr5) alloy. A special testing geometry was used to characterize the titanium alloys properties from the point of view of the forming zone and titanium structure effect. The structure and properties of the materials were assessed by means of metallographic analyses and microhardness measurements.The highest differences in the parameters assessed as a function of the sampling zone were observed in the case of alpha-phase Ti-Gr2at the expense of the most substantial sheet thinning occurrence. A springback causes a smaller stored deformation in Timetal (β alloy) resulting in less pronounced microstructure refinement and microhardness increase. Ti-6Al-4V alloy exhibited early failure due to its poor formability at ambient temperature.
Abstract: This article is concerned with the determination of the static interaction of a vertically loaded rigid circular disc embedded at the interface of a horizontal layer sandwiched in between two different transversely isotropic half-spaces called as tri-material full-space. The axes of symmetry of different regions are assumed to be normal to the horizontal interfaces and parallel to the movement direction. With the use of a potential function method, and by implementing Hankel integral transforms in the radial direction, the government partial differential equation for the solely scalar potential function is transformed to an ordinary 4th order differential equation, and the mixed boundary conditions are transformed into a pair of integral equations called dual integral equations, which can be reduced to a Fredholm integral equation of the second kind, which is solved analytically. Then, the displacements and stresses are given in the form of improper line integrals, which is due to inverse Hankel integral transforms. It is shown that the present solutions are in exact agreement with the existing solutions for a homogeneous full-space with transversely isotropic material. To confirm the accuracy of the numerical evaluation of the integrals involved, the numerical results are compared with the solutions exists for the homogeneous full-space. Then, some different cases with different degrees of material anisotropy are compared to portray the effect of degree of anisotropy.
Abstract: Rogowski coils are increasingly used for measurement
of AC and transient electric currents. Mostly used Rogowski coils
now are with circular or rectangular cores. In order to increase the
sensitivity of the measurement of Rogowski coil and perform smooth
wire winding, this paper studies the effect of increasing the mutual
inductance in order to increase the coil sensitivity by presenting the
calculation and simulation of a Rogowski coil with equilateral
hexagonal shaped core and comparing the resulted mutual inductance
with commonly used core shapes.
Abstract: This paper presents the results of an experimental
study on the effects of elevated temperature on compressive and
flexural strength of Normal Strength Concrete (NSC), High Strength
Concrete (HSC) and High Performance Concrete (HPC). In addition,
the specimen mass and volume were measured before and after
heating in order to determine the loss of mass and volume during the
test. In terms of non-destructive measurement, ultrasonic pulse
velocity test was proposed as a promising initial inspection method
for fire damaged concrete structure. 100 Cube specimens for three
grades of concrete were prepared and heated at a rate of 3°C/min up
to different temperatures (150, 250, 400, 600, and 900°C). The results
show a loss of compressive and flexural strength for all the concretes
heated to temperature exceeding 400°C. The results also revealed that
mass and density of the specimen significantly reduced with an
increase in temperature.
Abstract: Numerical study of heat transfer and fluid flow over vertical double forward facing step were presented. The k-w model with finite volume method was employed to solve continuity, momentum, and energy equations. Different step heights were adopted for range of Reynolds number varied from 10000 to 40000, and range of temperature varied from 310K to 340 K. The straight side of duct is insulated while the side of double forward facing step is heated. The result shows augmentation of heat transfer due to the recirculation region created after and before steps. Effect of step length and Reynolds number observed on increase of local Nusselt number particularly at recirculation regions. Contour of streamline velocity is plotted to show recirculation regions after and before steps. Numerical simulation in this paper done by used ANSYS FLUENT 14.
Abstract: Heat transfer and laminar fluid flow over backward facing step with and without obstacle numerically studied in this paper. The finite volume method adopted to solve continuity, momentum and energy equations in two dimensions. Backward facing step without obstacle and with different dimension of obstacle were presented. The step height and expansion ratio of channel were 4.8mm and 2 respectively, the range of Reynolds number varied from 75 to 225, constant heat flux subjected on downstream of wall was 2000W/m2, and length of obstacle was 1.5, 3, and 4.5mm with width 1.5mm. The separation length noticed increase with increase Reynolds number and height of obstacle. The result shows increase of heat transfer coefficient for backward facing step with obstacle in compared to those without obstacle. The maximum enhancement of heat transfer observed at 4.5mm of height obstacle due to increase recirculation flow after the obstacle in addition that at backward. Streamline of velocity showing the increase of recirculation region with used obstacle in compared without obstacle and highest recirculation region observed at obstacle height 4.5mm. The amount of enhancement heat transfer was varied between 3-5% compared to backward without obstacle.
Abstract: Analyzing classroom assessments is one of the responsibilities of the teacher. It aims improving teacher’s instruction and assessment as well as student learning. The present study investigated factors that might explain variation in teachers’ practices regarding analysis of classroom assessments. The factors considered in the investigation included gender, in-service assessment training, teaching load, teaching experience, knowledge in assessment, attitude towards quantitative aspects of assessment, and self-perceived competence in analyzing assessments. Participants were 246 in-service teachers in Oman. Results of a stepwise multiple linear regression analysis revealed that self-perceived competence was the only significant factor explaining the variance in teachers’ analysis of assessments. Implications for research and practice are discussed.
Abstract: The results of the study on the project evaluation to
develop the competencies, capabilities, and skills in repairing
computers of people in Jompluak Local Municipality, Bang Khonthi
District, Samut Songkram Province showed that the overall result
was good (4.33). When considering on each aspect, it was found that
the highest one was on process evaluation (4.60) followed by product
evaluation (4.50) and the least one was on feeding factor (3.97).
When considering in details, it was found that: 1) the context aspect
was high (4.23) with the highest item on the arrangement of the
training situation (4.67) followed by the appropriateness of the target
(4.30) and the least aspect was on the project cooperation (3.73). 2)
The evaluation of average overall primary factor or feeding factor
showed high value (4.23) while the highest aspect was on the
capability of the trainers (4.47) followed by the suitable venue (4.33)
while the least aspect was on the insufficient budget (3.47). 3) The
average result of process evaluation was very high (4.60). The
highest aspect was on the follow-op supervision (4.70) followed by
responsibility of each project staffs (4.50) while the least aspect was
on the present situation and the problems of the community (4.40). 4)
The overall result of the product evaluation was very high (4.50). The
highest aspect was on the diversity of the activities and the
community integration (4.67) followed by project target achievement
(4.63) while the least aspect was on continuation and regularity of the
activities (4.33). The trainees reported high satisfaction on the project
management at very high level (43.33%) while 40% reported high
level and 16.67% reported moderate level. Suggestions for the project
were on the additional number of the computer sets (37.78%)
followed by longer training period especially on computer skills
(43.48%).
Abstract: In this paper a novel method for the detection of
clipping in speech signals is described. It is shown that the new
method has better performance than known clipping detection
methods, is easy to implement, and is robust to changes in signal
amplitude, size of data, etc. Statistical simulation results are
presented.
Abstract: A thin gold metal layer was deposited on the top of
silicon oxide films containing embedded Si nanocrystals (Si-nc). The
sample was annealed in a gas containing nitrogen, and subsequently
characterized by photoluminescence. We obtained 3-fold
enhancement of photon emission from the Si-nc embedded in silicon
dioxide covered with a Gold layer as compared with an uncovered
sample. We attribute this enhancement to the increase of the
spontaneous emission rate caused by the coupling of the Si-nc
emitters with the surface plasmons (SP). The evolution of PL
emission with laser irradiated time was also collected from covered
samples, and compared to that from uncovered samples. In an
uncovered sample, the PL intensity decreases with time,
approximately with two decay constants. Although the decrease of
the initial PL intensity associated with the increase of sample
temperature under CW pumping is still observed in samples covered
with a gold layer, this film significantly contributes to reduce the
permanent deterioration of the PL intensity. The resistance to
degradation of light-emitting silicon nanocrystals can be increased by
SP coupling to suppress the permanent deterioration. Controlling the
permanent photodeterioration can allow to perform a reliable optical
gain measurement.
Abstract: The outstanding mechanical properties of Carbon
nanotubes (CNTs) have generated great interest for their potential as
reinforcements in high performance cementitious composites. The
main challenge in research is the proper dispersion of carbon
nanotubes in the cement matrix. The present work discusses the role
of dispersion of multiwalled carbon nanotubes (MWCNTs) on the
compressive strength characteristics of hydrated Portland IS 1489
cement paste. Cement-MWCNT composites with different mixing
techniques were prepared by adding 0.2% (by weight) of MWCNTs
to Portland IS 1489 cement. Rectangle specimens of size
approximately 40mm × 40mm ×160mm were prepared and curing of
samples was done for 7, 14, 28 and 35days. An appreciable increase
in compressive strength with both techniques; mixture of MWCNTs
with cement in powder form and mixture of MWCNTs with cement
in hydrated form 7 to 28 days of curing time for all the samples was
observed.
Abstract: The objectives of this research were to study the management of local towns and to develop a better model of town management according to the Philosophy of Sufficiency Economy. This study utilized qualitative research, field research, as well as documentary research at the same time. A total of 10 local towns or Tambons of Supanburi province, Thailand were selected for an in-depth interview. The findings revealed that the model of local town management according to Philosophy of Sufficient Economy was in a level of “good” and the model of management has the five basic guidelines: 1) ability to manage budget information and keep it up-to-date, 2) ability to decision making according to democracy rules, 3) ability to use check and balance system, 4) ability to control, follow, and evaluation, and 5) ability to allow the general public to participate. In addition, the findings also revealed that the human resource management according to Philosophy of Sufficient Economy includes obeying laws, using proper knowledge, and having integrity in five areas: plan, recruit, select, train, and maintain human resources.
Abstract: The two primary objectives of this research were (1)
to examine the current knowledge and actual circumstance of
agricultural workers about mangosteen product processing; and (2) to
analyze and evaluate ways to develop capacity of mangosteen
product processing. The population of this study was 15,125 people
who work in the agricultural sector, in this context, mangosteen
production, in the eastern part of Thailand that included Chantaburi
Province, Rayong Province, Trad Province and Pracheenburi
Province. The sample size based on Yamane’s calculation with 95%
reliability was therefore 392 samples. Mixed method was employed
included questionnaire and focus group discussion with
Connoisseurship Model used in order to collect quantitative and
qualitative data. Key informants were used in the focus group
including agricultural business owners, academic people in agro food
processing, local academics, local community development staff,
OTOP subcommittee, and representatives of agro processing
industry professional organizations. The study found that the
majority of the respondents agreed with a high level (in five- rating
scale) towards most of variables of knowledge management in agro
food processing. The result of the current knowledge and actual
circumstance of agricultural human resource in an arena of
mangosteen product processing revealed that mostly, the respondents
agreed at a high level to establish 7 variables. The guideline to
developing the body of knowledge in order to enhance the capacity
of the agricultural workers in mangosteen product processing was
delivered in the focus group discussion. The discussion finally
contributed to an idea to produce manuals for mangosteen product
processing methods, with 4 products chosen: (1) mangosteen soap;
(2) mangosteen juice; (3) mangosteen toffee; and (4) mangosteen
preserves or jam.
Abstract: Slab sliding system (SSS) with Coulomb friction
interface between slab and supporting frame is a passive structural
vibration control technology. The system can significantly reduce the
slab acceleration and accompanied lateral force of the frame. At the
same time it is expected to cause the slab displacement magnification
by sliding movement. To obtain the general comprehensive seismic
response of a single story structure, inelastic response spectra were
computed for a large ensemble of ground motions and a practical range
of structural periods and friction coefficient values. It was shown that
long period structures have no trade-off relation between force
reduction and displacement magnification with respect to elastic
response, unlike short period structures. For structures with the
majority of mass in the slab, the displacement magnification value can
be predicted according to simple inelastic displacement relation for
inelastically responding SDOF structures because the system behaves
elastically to a SDOF structure.
Abstract: In the age of globalization, higher education
institutions attempt to equip students with global competence. In
response, most universities have been developing and running various
international programs. However, teacher education has been a
neglected area in this trend. Therefore, in this study, we suggest a
program that offers a dual bachelor’s degree from both universities
located on different countries, focusing on teacher education
institutions with different policies and regulations of teacher education
programs that may become obstacles to designing a dual degree
program. We discuss a possible way to get a dual degree including a
teaching certificate at a specialized college, college of secondary
education. To be specific, this research presents a way to attain two
diplomas from Jeju National University (JNU) in Korea and Boise
State University (BSU) in the U.S. It attempts to build an effective
plan for students to declare simultaneous degrees at both universities.
From the study, we find that it takes about 5 years to fulfill
requirements for the dual degree at the undergraduate level.
Abstract: Recently, ‘play of learning’ becomes important and is
emphasized as a useful learning tool. Therefore, interest in
edutainment contents is growing. Storytelling is considered first as a
method that improves the transmission of information and learner's
interest when planning edutainment contents. In this study, we
designed edutainment contents in the form of an adventure game that
applies the storytelling method. This content provides questions and
items constituted dynamically and reorganized learning contents
through analysis of test results. It allows learners to solve various
questions through effective iterative learning. As a result, the learners
can reach mastery learning.
Abstract: Patients under health treatments that involve long
stays at a hospital or health center (e.g. cancer, organ transplants and
severe burns), tend to get bored or depressed because of the lack of
social interaction with family and friends. Such a situation also
affects the evolution and effectiveness of their treatments. In many
cases, the solution to this problem involves extra challenges, since
many patients need to rest quietly (or remain in bed) to their being
contagious. Considering the weak health condition in which usually
are these kinds, keeping them motivated and quiet represents an
important challenge for nurses and caregivers. This article presents a
mobile ubiquitous game called MagicRace, which allows hospitalized
kinds to interact socially with one another without putting to risk
their sensitive health conditions. The game does not require a
communication infrastructure at the hospital, but instead, it uses a
mobile ad hoc network composed of the handheld devices used by
the kids to play. The usability and performance of this application
was tested in two different sessions. The preliminary results show
that users experienced positive feelings from this experience.
Abstract: This paper gave an attempt in prioritizing information
technologies that organizations should give concentration. The case
study was organizations in the automotive assembly industry in
Thailand. Data were first collected to gather all information
technologies known and used in the automotive assembly industry in
Thailand. Five experts from the industries were surveyed based on
the concept of fuzzy DEMATEL. The information technologies were
categorized into six groups, which were communication, transaction,
planning, organization management, warehouse management, and
transportation. The cause groups of information technologies for each
group were analyzed and presented. Moreover, the relationship
between the used and the significant information technologies was
given. Discussions based on the used information technologies and
the research results are given.