Abstract: A kind of singularly perturbed boundary value problems is under consideration. In order to obtain its approximation, simple upwind difference discretization is applied. We use a moving mesh iterative algorithm based on equi-distributing of the arc-length function of the current computed piecewise linear solution. First, a maximum norm a posteriori error estimate on an arbitrary mesh is derived using a different method from the one carried out by Chen [Advances in Computational Mathematics, 24(1-4) (2006), 197-212.]. Then, basing on the properties of discrete Green-s function and the presented posteriori error estimate, we theoretically prove that the discrete solutions computed by the algorithm are first-order uniformly convergent with respect to the perturbation parameter ε.
Abstract: In this work, simulation algorithms for contact drying
of agitated particulate materials under vacuum and at atmospheric
pressure were developed. The implementation of algorithms gives a
predictive estimation of drying rate curves and bulk bed temperature
during contact drying. The calculations are based on the penetration
model to describe the drying process, where all process parameters
such as heat and mass transfer coefficients, effective bed properties,
gas and liquid phase properties are estimated with proper
correlations. Simulation results were compared with experimental
data from the literature. In both cases, simulation results were in good
agreement with experimental data. Few deviations were identified
and the limitations of the predictive capabilities of the models are
discussed. The programs give a good insight of the drying behaviour
of the analysed powders.
Abstract: This paper discusses the utilization of marine biomass as an energy resource in Japan. A marine biomass energy system in Japan was proposed consisting of seaweed cultivation (Laminaria japonica) at offshore marine farms, biogas production via methane fermentation of the seaweeds, and fuel cell power generation driven by the generated biogas. We estimated energy output, energy supply potential, and CO2 mitigation in Japan on the basis of the proposed system. As a result, annual energy production was estimated to be 1.02-109 kWh/yr at nine available sites. Total CO2 mitigation was estimated to be 1.04-106 tonnes per annum at the nine sites. However, the CO2 emission for the construction of relevant facilities is not taken into account in this paper. The estimated CO2 mitigation is equivalent to about 0.9% of the required CO2 mitigation for Japan per annum under the Kyoto Protocol framework.
Abstract: In this paper we propose a Multiple Description Image Coding(MDIC) scheme to generate two compressed and balanced rates descriptions in the wavelet domain (Daubechies biorthogonal (9, 7) wavelet) using pairwise correlating transform optimal and application method for Generalized Multiple Description Coding (GMDC) to image coding in the wavelet domain. The GMDC produces statistically correlated streams such that lost streams can be estimated from the received data. Our performance test shown that the proposed method gives more improvement and good quality of the reconstructed image when the wavelet coefficients are normalized by Gaussian Scale Mixture (GSM) model then the Gaussian one ,.
Abstract: To determine the length of engagement threads of a bolt installed in a tapped part in order to avoid the threads stripping remains a very current problem in the design of the thread assemblies. It does not exist a calculation method formalized for the cases where the bolt is screwed directly in a ductile material. In this article, we study the behavior of the threads stripping of a loaded assembly by using a modelling by finite elements and a rupture criterion by damage. This modelling enables us to study the different parameters likely to influence the behavior of this bolted connection. We study in particular, the influence of couple of materials constituting the connection, of the bolt-s diameter and the geometrical characteristics of the tapped part, like the external diameter and the length of engagement threads. We established an experiments design to know the most significant parameters. That enables us to propose a simple expression making possible to calculate the resistance of the threads whatever the metallic materials of the bolt and the tapped part. We carried out stripping tests in order to validate our model. The estimated results are very close to those obtained by the tests.
Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: Nowadays, the increase of human population every
year results in increasing of water usage and demand. Saen Saep
canal is important canal in Bangkok. The main objective of this study
is using Artificial Neural Network (ANN) model to estimate the
Chemical Oxygen Demand (COD) on data from 11 sampling sites.
The data is obtained from the Department of Drainage and Sewerage,
Bangkok Metropolitan Administration, during 2007-2011. The
twelve parameters of water quality are used as the input of the
models. These water quality indices affect the COD. The
experimental results indicate that the ANN model provides a high
correlation coefficient (R=0.89).
Abstract: This report aims to utilize existing and future Multiple-Input Multiple-Output Orthogonal Frequency Division Multiplexing Wireless Local Area Network (MIMO-OFDM WLAN) systems characteristics–such as multiple subcarriers, multiple antennas, and channel estimation characteristics–for indoor location estimation systems based on the Direction of Arrival (DOA) and Radio Signal Strength Indication (RSSI) methods. Hybrid of DOA-RSSI methods also evaluated. In the experimental data result, we show that location estimation accuracy performances can be increased by minimizing the multipath fading effect. This is done using multiple subcarrier frequencies over wideband frequencies to estimate one location. The proposed methods are analyzed in both a wide indoor environment and a typical room-sized office. In the experiments, WLAN terminal locations are estimated by measuring multiple subcarriers from arrays of three dipole antennas of access points (AP). This research demonstrates highly accurate, robust and hardware-free add-on software for indoor location estimations based on a MIMO-OFDM WLAN system.
Abstract: The present work analyses different parameters of pressure die casting to minimize the casting defects. Pressure diecasting is usually applied for casting of aluminium alloys. Good surface finish with required tolerances and dimensional accuracy can be achieved by optimization of controllable process parameters such as solidification time, molten temperature, filling time, injection pressure and plunger velocity. Moreover, by selection of optimum process parameters the pressure die casting defects such as porosity, insufficient spread of molten material, flash etc. are also minimized. Therefore, a pressure die casting component, carburetor housing of aluminium alloy (Al2Si2O5) has been considered. The effects of selected process parameters on casting defects and subsequent setting of parameters with the levels have been accomplished by Taguchi-s parameter design approach. The experiments have been performed as per the combination of levels of different process parameters suggested by L18 orthogonal array. Analyses of variance have been performed for mean and signal-to-noise ratio to estimate the percent contribution of different process parameters. Confidence interval has also been estimated for 95% consistency level and three conformational experiments have been performed to validate the optimum level of different parameters. Overall 2.352% reduction in defects has been observed with the help of suggested optimum process parameters.
Abstract: Wireless location is to determine the mobile station (MS) location in a wireless cellular communications system. When fewer base stations (BSs) may be available for location purposes or the measurements with large errors in non-line-of-sight (NLOS) environments, it is necessary to integrate all available heterogeneous measurements to achieve high location accuracy. This paper illustrates a hybrid proposed schemes that combine time of arrival (TOA) at three BSs and angle of arrival (AOA) information at the serving BS to give a location estimate of the MS. The proposed schemes mitigate the NLOS effect simply by the weighted sum of the intersections between three TOA circles and the AOA line without requiring a priori information about the NLOS error. Simulation results show that the proposed methods can achieve better accuracy when compare with Taylor series algorithm (TSA) and the hybrid lines of position algorithm (HLOP).
Abstract: As a simple to method estimate the plant heating energy
capacity of an apartment complex, a new load calculation method has
been proposed. The method which can be called as unit building
method, predicts the heating load of the entire complex instead of
summing up that of each apartment belonging to complex.
Comparison of the unit heating load for various floor sizes between the
present method and conventional approach shows a close agreement
with dynamic load calculation code. Some additional calculations are
performed to demonstrate it-s application examples.
Abstract: The objective of this research was to find the diffusion properties of vehicles on the road by using the V-Sphere Code. The diffusion coefficient and the size of the height of the wake were estimated with the LES option and the third order MUSCL scheme. We evaluated the code with the changes in the moments of Reynolds Stress along the mean streamline. The results show that at the leading part of a bluff body the LES has some advantages over the RNS since the changes in the strain rates are larger for the leading part. We estimated that the diffusion coefficient with the computed Reynolds stress (non-dimensional) was about 0.96 times the mean velocity.
Abstract: An automatic speech recognition system for the
formal Arabic language is needed. The Quran is the most formal
spoken book in Arabic, it is spoken all over the world. In this
research, an automatic speech recognizer for Quranic based speakerindependent
was developed and tested. The system was developed
based on the tri-phone Hidden Markov Model and Maximum
Likelihood Linear Regression (MLLR). The MLLR computes a set
of transformations which reduces the mismatch between an initial
model set and the adaptation data. It uses the regression class tree, as
well as, estimates a set of linear transformations for the mean and
variance parameters of a Gaussian mixture HMM system. The 30th
Chapter of the Quran, with five of the most famous readers of the
Quran, was used for the training and testing of the data. The chapter
includes about 2000 distinct words. The advantages of using the
Quranic verses as the database in this developed recognizer are the
uniqueness of the words and the high level of orderliness between
verses. The level of accuracy from the tested data ranged 68 to 85%.
Abstract: We propose a downlink multiple-input multipleoutput
(MIMO) multi-carrier code division multiple access (MCCDMA)
system with adaptive beamforming algorithm for smart
antennas. The algorithm used in this paper is based on the Least
Mean Square (LMS), with pilot channel estimation (PCE) and the
zero forcing equalizer (ZFE) in the receiver, requiring reference
signal and no knowledge channel. MC-CDMA is studied in a
multiple antenna context in order to efficiently exploit robustness
against multipath effects and multi-user flexibility of MC-CDMA and
channel diversity offered by MIMO systems for radio mobile
channels. Computer simulations, considering multi-path Rayleigh
Fading Channel, interference inter symbol and interference are
presented to verify the performance. Simulation results show that the
scheme achieves good performance in a multi-user system.
Abstract: A concern that researchers usually face in different
applications of Artificial Neural Network (ANN) is determination of
the size of effective domain in time series. In this paper, trial and
error method was used on groundwater depth time series to determine
the size of effective domain in the series in an observation well in
Union County, New Jersey, U.S. different domains of 20, 40, 60, 80,
100, and 120 preceding day were examined and the 80 days was
considered as effective length of the domain. Data sets in different
domains were fed to a Feed Forward Back Propagation ANN with
one hidden layer and the groundwater depths were forecasted. Root
Mean Square Error (RMSE) and the correlation factor (R2) of
estimated and observed groundwater depths for all domains were
determined. In general, groundwater depth forecast improved, as
evidenced by lower RMSEs and higher R2s, when the domain length
increased from 20 to 120. However, 80 days was selected as the
effective domain because the improvement was less than 1% beyond
that. Forecasted ground water depths utilizing measured daily data
(set #1) and data averaged over the effective domain (set #2) were
compared. It was postulated that more accurate nature of measured
daily data was the reason for a better forecast with lower RMSE
(0.1027 m compared to 0.255 m) in set #1. However, the size of input
data in this set was 80 times the size of input data in set #2; a factor
that may increase the computational effort unpredictably. It was
concluded that 80 daily data may be successfully utilized to lower the
size of input data sets considerably, while maintaining the effective
information in the data set.
Abstract: The presence of toxic heavy metals in industrial
effluents is one of the serious threats to the environment. Heavy
metals such as Cadmium, Chromium, Lead, Nickel, Zinc, Mercury,
Copper, Arsenic are found in the effluents of industries such as
foundries, electroplating, petrochemical, battery manufacturing,
tanneries, fertilizer, dying, textiles, metallurgical and metal finishing.
Tremendous increase of industrial copper usage and its presence in
industrial effluents has lead to a growing concern about the fate and
effects of Copper in the environment. Percolation of industrial
effluents through soils leads to contamination of ground water and
soils. The transport of heavy metals and their diffusion into the soils
has therefore, drawn the attention of the researchers.
In this study, an attempt has been made to delineate the
mechanisms of transport and fate of copper in terrestrial
environment. Column studies were conducted using perplex glass
square column of dimension side 15 cm and 1.35 m long. The soil
samples were collected from a natural drain near Mohali (India). The
soil was characterized to be poorly graded sandy loam. The soil was
compacted to the field dry density level of about 1.6 g/cm3. Break
through curves for different depths of the column were plotted. The
results of the column study indicated that the copper has high
tendency to flow in the soils and fewer tendencies to get absorbed on
the soil particles. The t1/2 estimates obtained from the studies can be
used for design copper laden wastewater disposal systems.
Abstract: Due to the high percentage of induction motors in industrial market, there exist a large opportunity for energy savings. Replacement of working induction motors with more efficient ones can be an important resource for energy savings. A calculation of energy savings and payback periods, as a result of such a replacement, based on nameplate motor efficiency or manufacture-s data can lead to large errors [1]. Efficiency of induction motors (IMs) can be extracted using some procedures that use the no-load test results. In the cases that we must estimate the efficiency on-line, some of these procedures can-t be efficient. In some cases the efficiency estimates using the rating values of the motor, but these procedures can have errors due to the different working condition of the motor. In this paper the efficiency of an IM estimated by using the genetic algorithm. The results are compared with the measured values of the torque and power. The results show smaller errors for this procedure compared with the conventional classical procedures, hence the cost of the equipments is reduced and on-line estimation of the efficiency can be made.
Abstract: The recent global financial problem urges government
to play role in stimulating the economy due to the fact that private
sector has little ability to purchase during the recession. A concerned
question is whether the increased government spending crowds out
private consumption and whether it helps stimulate the economy. If
the government spending policy is effective; the private consumption
is expected to increase and can compensate the recent extra
government expense. In this study, the government spending is
categorized into government consumption spending and government
capital spending. The study firstly examines consumer consumption
along the line with the demand function in microeconomic theory.
Three categories of private consumption are used in the study. Those
are food consumption, non food consumption, and services
consumption. The dynamic Almost Ideal Demand System of the three
categories of the private consumption is estimated using the Vector
Error Correction Mechanism model. The estimated model indicates
the substituting effects (negative impacts) of the government
consumption spending on budget shares of private non food
consumption and of the government capital spending on budget share
of private food consumption, respectively. Nevertheless the result
does not necessarily indicate whether the negative effects of changes
in the budget shares of the non food and the food consumption means
fallen total private consumption. Microeconomic consumer demand
analysis clearly indicates changes in component structure of
aggregate expenditure in the economy as a result of the government
spending policy. The macroeconomic concept of aggregate demand
comprising consumption, investment, government spending (the
government consumption spending and the government capital
spending), export, and import are used to estimate for their
relationship using the Vector Error Correction Mechanism model.
The macroeconomic study found no effect of the government capital
spending on either the private consumption or the growth of GDP
while the government consumption spending has negative effect on
the growth of GDP. Therefore no crowding out effect of the
government spending is found on the private consumption but it is
ineffective and even inefficient expenditure as found reducing growth
of the GDP in the context of Thailand.
Abstract: Power Spectral Density (PSD) of quasi-stationary processes can be efficiently estimated using the short time Fourier series (STFT). In this paper, an algorithm has been proposed that computes the PSD of quasi-stationary process efficiently using offline autoregressive model order estimation algorithm, recursive parameter estimation technique and modified sliding window discrete Fourier Transform algorithm. The main difference in this algorithm and STFT is that the sliding window (SW) and window for spectral estimation (WSA) are separately defined. WSA is updated and its PSD is computed only when change in statistics is detected in the SW. The computational complexity of the proposed algorithm is found to be lesser than that for standard STFT technique.
Abstract: This study investigated a strategy of blending lead-laden sludge and Al-rich precursors to reduce the release of metals from the stabilized products. Using PbO as the simulated lead-laden sludge to sinter with γ-Al2O3 by Pb:Al molar ratios of 1:2 and 1:12, PbAl2O4 and PbAl12O19 were formed as final products during the sintering process, respectively. By firing the PbO + γ-Al2O3 mixtures with different Pb/Al molar ratios at 600 to 1000 °C, the lead transformation was determined through X-ray diffraction (XRD) data. In Pb/Al molar ratio of 1/2 system, the formation of PbAl2O4 is initiated at 700 °C, but an effective formation was observed above 750 °C. An intermediate phase, Pb9Al8O21, was detected in the temperature range of 800-900 °C. However, different incorporation behavior for sintering PbO with Al-rich precursors at a Pb/Al molar ratio of 1/12 was observed during the formation of PbAl12O19 in this system. In the sintering process, both temperature and time effect on the formation of PbAl2O4 and PbAl12O19 phases were estimated. Finally, a prolonged leaching test modified from the U.S. Environmental Protection Agency-s toxicity characteristic leaching procedure (TCLP) was used to evaluate the durability of PbO, Pb9Al8O21, PbAl2O4 and PbAl12O19 phases. Comparison for the leaching results of the four phases demonstrated the higher intrinsic resistance of PbAl12O19 against acid attack.