Abstract: Laser soldering is based on applying some soldering material (albumin) onto the approximated edges of the cut and heating the solder (and the underlying tissues) by a laser beam. Endogenous and exogenous materials such as indocyanine green (ICG) are often added to solders to enhance light absorption. Gold nanoshells are new materials which have an optical response dictated by the plasmon resonance. The wavelength at which the resonance occurs depends on the core and shell sizes, allowing nanoshells to be tailored for particular applications. The purposes of this study was use combination of ICG and different concentration of gold nanoshells for skin tissue soldering and also to examine the effect of laser soldering parameters on the properties of repaired skin. Two mixtures of albumin solder and different combinations of ICG and gold nanoshells were prepared. A full thickness incision of 2×20 mm2 was made on the surface and after addition of mixtures it was irradiated by an 810nm diode laser at different power densities. The changes of tensile strength σt due to temperature rise, number of scan (Ns), and scan velocity (Vs) were investigated. The results showed at constant laser power density (I), σt of repaired incisions increases by increasing the concentration of gold nanoshells in solder, Ns and decreasing Vs. It is therefore important to consider the tradeoff between the scan velocity and the surface temperature for achieving an optimum operating condition. In our case this corresponds to σt =1800 gr/cm2 at I~ 47 Wcm-2, T ~ 85ºC, Ns =10 and Vs=0.3mms-1.
Abstract: Data on 657 lactation from 163 Maltese goat,
collected over a 5-year period were analyzed by a mixed model to
estimate the variance components for heritability. The considered
lactation traits were: milk yield (MY) and lactation length (LL). Year,
parity and type of birth (single or twin) were significant sources of
variation for lactation length; on the other hand milk yield was
significantly influenced only by the year. The average MY was
352.34 kg and the average LL was 230 days. Estimates of heritability
were 0.21 and 0.15 for MY and LL respectively. These values
suggest there is low correlation between genotype and phenotype so
it may be difficult to evaluate animals directly on phenotype. So, the
genetic improvement of this breed may be quite slow without the
support of progeny test aimed to select Maltese breeders.
Abstract: Self-propelled forage harvesters in the 850
horsepower range were tested over three years for fuel consumption,
throughput and quality of chop for corn silage. Cut length had a
significant effect on fuel consumption, throughput and some aspects
of chop quality. Measure cut length was often different than
theoretical length of cut. Where cut length was equivalent fuel
consumption and throughput were equivalent across brands.
Shortening cut length from 17 to 11mm increases fuel consumption
53 percent measured as Mg of silage harvested per gallon of fuel used
and a 42 percent decrease in capacity as tons of fresh material per
hour run time.
Abstract: The importance of machining process in today-s
industry requires the establishment of more practical approaches to
clearly represent the intimate and severe contact on the tool-chipworkpiece
interfaces. Mathematical models are developed using the
measured force signals to relate each of the tool-chip friction
components on the rake face to the operating cutting parameters in
rough turning operation using multilayers coated carbide inserts.
Nonlinear modeling proved to have high capability to detect the
nonlinear functional variability embedded in the experimental data.
While feedrate is found to be the most influential parameter on the
friction coefficient and its related force components, both cutting
speed and depth of cut are found to have slight influence. Greater
deformed chip thickness is found to lower the value of friction
coefficient as the sliding length on the tool-chip interface is reduced.
Abstract: We theoretically demonstrate modulation of light
polarization by a crossed rectangular hole array with asymmetric arm
lengths. There are two waveguide modes that can modulate the x- and
y- polarized incident waves independently. A specific structure is
proposed to convert a left-hand incident wave to a right-hand outgoing
wave by transmission.
Abstract: This paper presents an exact analytical model for
optimizing stability of thin-walled, composite, functionally graded
pipes conveying fluid. The critical flow velocity at which divergence
occurs is maximized for a specified total structural mass in order to
ensure the economic feasibility of the attained optimum designs. The
composition of the material of construction is optimized by defining
the spatial distribution of volume fractions of the material
constituents using piecewise variations along the pipe length. The
major aim is to tailor the material distribution in the axial direction so
as to avoid the occurrence of divergence instability without the
penalty of increasing structural mass. Three types of boundary
conditions have been examined; namely, Hinged-Hinged, Clamped-
Hinged and Clamped-Clamped pipelines. The resulting optimization
problem has been formulated as a nonlinear mathematical
programming problem solved by invoking the MatLab optimization
toolbox routines, which implement constrained function
minimization routine named “fmincon" interacting with the
associated eigenvalue problem routines. In fact, the proposed
mathematical models have succeeded in maximizing the critical flow
velocity without mass penalty and producing efficient and economic
designs having enhanced stability characteristics as compared with
the baseline designs.
Abstract: The paper provides an in-depth tutorial of mathematical
construction of maximal length sequences (m-sequences) via primitive
polynomials and how to map the same when implemented in
shift registers. It is equally important to check whether a polynomial
is primitive or not so as to get proper m-sequences. A fast method to
identify primitive polynomials over binary fields is proposed where
the complexity is considerably less in comparison with the standard
procedures for the same purpose.
Abstract: The ITE Project is a project that has 1800 km length
and across the Turkey's land through east to west. The project of
pipeline enters geographically from Iran to Doğubayazit (Turkey) in
the east, exits to Greece from Ipsala province of Turkey in the west.
This project is the one of the international projects in such scale that
provides the natural gas of Iran and Caspian Sea through the
European continent. In this investigation, some information will be
given about the methods used to verify the direction of the pipeline
and the technical properties of the results obtained. The cost of
project itself entirely depends on the direction of the pipeline which
would be as short as possible and the specifications of the land cover.
Production standards of 1/2000 scaled digital orthophoto and vectoral
maps as a results of the use of map production materials and methods
(such as high resolution satellite images, and digital aerial images
captured from digital aerial cameras), will also be given in this report.
According to Turkish national map production standards, TM
((Transversal Mercator, 3 degree) projection is used for large scale
map and UTM (Universal Transversal Mercator, 6 degree) is used for
small scale map production standards. Some information is also given
about the projection used in the ITE natural gas pipeline project.
Abstract: This paper presents the results of the experimental
tests of the cooling performance of a 12,000-Btu/h modified air
conditioner (referred to as M-AC) that use the ground as a heat sink
of a condenser. In the tests, cooling capacity of M-AC with an
optimal length of a condensing coil as well as life expectancy of
copper coil buried underground were investigated. The lengths of
copper coil fabricated and used as condenser coil of M-AC were set
at 67, 50, 40 and 30 m whereas that of a 12,000-Btu/h conventional
split-type air conditioner (referred to as C-AC) was about 22 m. The
results showed that the ground can absorb heat rejected from a
condenser of M-AC. The coefficient of performance (COP) of C-AC
was about 2.5 whereas those of M-AC were found to be higher. It
was found that the values of COP of M-AC with condensing coils of
67, 50 and 40 m long were about 6.9, 5.5 and 3.3, respectively, while
that of 30-m-long one was found to be about 2.1. The electrical
consumptions of M-AC were found lower than that of C-AC in the
range of 11.5 – 15.5%. Additionally, life expectancy of underground
condensing coil of M-AC was found to be over 7 years.
Abstract: The temporal nature of negative selection is an under exploited area. In a negative selection system, newly generated antibodies go through a maturing phase, and the survivors of the phase then wait to be activated by the incoming antigens after certain number of matches. These without having enough matches will age and die, while these with enough matches (i.e., being activated) will become active detectors. A currently active detector may also age and die if it cannot find any match in a pre-defined (lengthy) period of time. Therefore, what matters in a negative selection system is the dynamics of the involved parties in the current time window, not the whole time duration, which may be up to eternity. This property has the potential to define the uniqueness of negative selection in comparison with the other approaches. On the other hand, a negative selection system is only trained with “normal" data samples. It has to learn and discover unknown “abnormal" data patterns on the fly by itself. Consequently, it is more appreciate to utilize negation selection as a system for pattern discovery and recognition rather than just pattern recognition. In this paper, we study the potential of using negative selection in discovering unknown temporal patterns.
Abstract: The power consumption of an Optical Packet Switch
equipped with SOA technology based Spanke switching fabric is
evaluated. Sophisticated analytical models are introduced to evaluate
the power consumption versus the offered traffic, the main
switch parameters, and the used device characteristics. The impact
of Amplifier Spontaneous Emission (ASE) noise generated by a
transmission system on the power consumption is investigated. As
a matter of example for 32×32 switches supporting 64 wavelengths
and offered traffic equal to 0,8, the average energy consumption per
bit is 5, 07 · 10-2 nJ/bit and increases if ASE noise introduced by
the transmission systems is increased.
Abstract: The purpose of this study is mainly to predict collision
frequency on the horizontal tangents combined with vertical curves
using artificial neural network methods. The proposed ANN models
are compared with existing regression models. First, the variables
that affect collision frequency were investigated. It was found that
only the annual average daily traffic, section length, access density,
the rate of vertical curvature, smaller curve radius before and after
the tangent were statistically significant according to related
combinations. Second, three statistical models (negative binomial,
zero inflated Poisson and zero inflated negative binomial) were
developed using the significant variables for three alignment
combinations. Third, ANN models are developed by applying the
same variables for each combination. The results clearly show that
the ANN models have the lowest mean square error value than those
of the statistical models. Similarly, the AIC values of the ANN
models are smaller to those of the regression models for all the
combinations. Consequently, the ANN models have better statistical
performances than statistical models for estimating collision
frequency. The ANN models presented in this paper are
recommended for evaluating the safety impacts 3D alignment
elements on horizontal tangents.
Abstract: Optical network uses a tool for routing which is called
Latin router. These routers use particular algorithms for routing. In this paper, we present algorithm for configuration of optical network that is optimized regarding previous algorithm. We show that by decreasing the number of hops for source-destination in lightpath number of satisfied request is less. Also we had shown that more than
single-hop lightpath relating single-hop lightpath is better.
Abstract: In the present work, an attempt is made to understand
electromagnetic field confinement in a subwavelength waveguide
structure using concepts of quantum mechanics. Evanescent field in
the waveguide is looked as inability of the photon to get confined in
the waveguide core and uncertainty of position is assigned to it. The
momentum uncertainty is calculated from position uncertainty.
Schrödinger wave equation for the photon is written by incorporating
position-momentum uncertainty. The equation is solved and field
distribution in the waveguide is obtained. The field distribution and
power confinement is compared with conventional waveguide theory.
They were found in good agreement with each other.
Abstract: Stocking density is considered one of the important
factors affecting fish growth. But, information related to impact of
stocking density on growth performance of monosex tilapia population
under the ecological conditions of Gangetic plains in West Bengal,
India is limited. The aim of our study was to compare the growth
potential of monosex tilapia at various stocking densities and to
determine an ideal stocking density for culture of all-male monosex
fish. The males were isolated by examination of genital papilla region
and were stocked separately in 0.01 ha earthen ponds at different
stocking densities (5000, 10000, 15000, 20000, 25000 and 30000
fingerlings/ha). It was found that the highest weight, length, daily
weight gain, growth rate and protein content were observed for the
20000 fish/ha density class. Thus, culture of monosex tilapia at a
density of 20000 fish/ha can be considered ideal for augmented
production of the fish under Indian context.
Abstract: In the present study, 49 Hybrid (Catla catla ♂ x
Labeo rohita ♀) were sampled from Al-Raheem Fish Hatchery,
Village Ali Pure Shamali, Jhang Road, 18 Km from Muzaffar Garh
using a cast net and Live fishes were transported to research
laboratory. Mean percentage for water found 79.13 %, ash 6.58 %, fat
2.22 % and protein content 12.06 % in whole wet body weight. It was
observed that body constituents were found increasing in the same
proportion with an increase in body weight while significant
proportional increase was observed with total length. However,
condition factor remained insignificant (P>0.05) with body
constituents.
Abstract: Behavior of turbulent jet is relying on jet parameters,
environmental and geometric parameters. In this research, it has
attempt to Study effect of jet parameters of internal angle on
maximum effective length and velocity on centerline from nozzle
experimentally. Toward this end, four internal angles 30, 45, 60 and
90-degree are considered for this study in a flume with 600cm as
long, 100cm as high and 150cm in width. Various discharges were
used to evaluate effective length for a wide range of densimetric
Froude numbers F0, from 17.9 to 39.4 that is defined at the nozzle. As
a result, It is revealed that both velocity on centerline and effective
length decreases when nozzle angle decreased from 90° to 30°. The
results show that, for all range of Fr0 the Um/U0 ratio for nozzle with
α=90° on centerline increases 20% - 27% than nozzle with α=30° that
has lowest velocity on centerline than other nozzle.
Abstract: Modern manufacturing facilities are large scale,
highly complex, and operate with large number of variables under
closed loop control. Early and accurate fault detection and diagnosis
for these plants can minimise down time, increase the safety of plant
operations, and reduce manufacturing costs. Fault detection and
isolation is more complex particularly in the case of the faulty analog
control systems. Analog control systems are not equipped with
monitoring function where the process parameters are continually
visualised. In this situation, It is very difficult to find the relationship
between the fault importance and its consequences on the product
failure. We consider in this paper an approach to fault detection and
analysis of its effect on the production quality using an adaptive
centring and scaling in the pickling process in cold rolling. The fault
appeared on one of the power unit driving a rotary machine, this
machine can not track a reference speed given by another machine.
The length of metal loop is then in continuous oscillation, this affects
the product quality. Using a computerised data acquisition system,
the main machine parameters have been monitored. The fault has
been detected and isolated on basis of analysis of monitored data.
Normal and faulty situation have been obtained by an artificial neural
network (ANN) model which is implemented to simulate the normal
and faulty status of rotary machine. Correlation between the product
quality defined by an index and the residual is used to quality
classification.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. Several cellular materials are widely used
as core of the sandwich structures and their properties influence
the response of the entire element under impact load. To optimize
their performance requires the characterisation of the core material
behaviour at high strain rates and identification of the underlying
mechanism. This work presents the study of high strain-rate
characteristics of a specific porous lightweight blast energy absorbing
foam using a Split Hopkinson Pressure Bar (SHPB) technique
adapted to perform tests on low strength materials. Two different
velocities, 15 and 30 m.s-1 were used to determine the strain
sensitivity of the material. Foams were designed using two types of
porous lightweight spherical raw materials with diameters of 30-
100 *m, combined with polymer matrix. Cylindrical specimens with
diameter of 15 mm and length of 7 mm were prepared and loaded
using a Split Hopkinson Pressure Bar apparatus to assess the relation
between the composition of the material and its shock wave
attenuation capacity.
Abstract: METIS is the Multi Element Telescope for Imaging
and Spectroscopy, a Coronagraph aboard the European Space
Agency-s Solar Orbiter Mission aimed at the observation of the solar
corona via both VIS and UV/EUV narrow-band imaging and spectroscopy. METIS, with its multi-wavelength capabilities, will
study in detail the physical processes responsible for the corona heating and the origin and properties of the slow and fast solar wind.
METIS electronics will collect and process scientific data thanks to its detectors proximity electronics, the digital front-end subsystem
electronics and the MPPU, the Main Power and Processing Unit,
hosting a space-qualified processor, memories and some rad-hard
FPGAs acting as digital controllers.This paper reports on the overall
METIS electronics architecture and data processing capabilities
conceived to address all the scientific issues as a trade-off solution between requirements and allocated resources, just before the
Preliminary Design Review as an ESA milestone in April 2012.