Abstract: The rate of production of main products of the Fischer-Tropsch reactions over Fe/HZSM5 bifunctional catalyst in a fixed bed reactor is investigated at a broad range of temperature, pressure, space velocity, H2/CO feed molar ratio and CO2, CH4 and water flow rates. Model discrimination and parameter estimation were performed according to the integral method of kinetic analysis. Due to lack of mechanism development for Fisher – Tropsch Synthesis on bifunctional catalysts, 26 different models were tested and the best model is selected. Comprehensive one and two dimensional heterogeneous reactor models are developed to simulate the performance of fixed-bed Fischer – Tropsch reactors. To reduce computational time for optimization purposes, an Artificial Feed Forward Neural Network (AFFNN) has been used to describe intra particle mass and heat transfer diffusion in the catalyst pellet. It is seen that products' reaction rates have direct relation with H2 partial pressure and reverse relation with CO partial pressure. The results show that the hybrid model has good agreement with rigorous mechanistic model, favoring that the hybrid model is about 25-30 times faster.
Abstract: A self-association model has been used to understand
the concentration dependence of free energy of mixing (GM), heat of
mixing (HM), entropy of mixing (SM), activity (a) and microscopic
structures, such as concentration fluctuation in long wavelength limit
(Scc(0)) and Warren-Cowley short range order parameter ( 1
α )for Cu-
Tl molten alloys at 1573K. A comparative study of surface tension of
the alloys in the liquid state at that temperature has also been carried
out theoretically as function of composition in the light of Butler-s
model, Prasad-s model and quasi-chemical approach. Most of the
computed thermodynamic properties have been found in agreement
with the experimental values. The analysis reveals that the Cu-Tl
molten alloys at 1573K represent a segregating system at all
concentrations with moderate interaction. Surface tensions computed
from different approaches have been found to be comparable to each
other showing increment with the composition of copper.
Abstract: Computer-based decision support (CDSS) systems can
deliver real patient care and increase chances of long-term survival in
areas of chronic disease management prone to poor control. One such
CDSS, for the management of warfarin, is described in this paper and
the outcomes shown. Data is derived from the running system and
show a performance consistently around 20% better than the
applicable guidelines.
Abstract: In this study, the conversion of n-pentane to aromatics is investigated on HZSM-5 zeolites modified by Ga ion-exchange and silylation using tetraethyl orthosilicate (TEOS) via chemical liquid deposition (CLD). The effect of SiO2/Al2O3 ratios of HZSM-5 was also studied. Parameters in preparing catalysts i.e. TEOS loading and cycles of deposition were varied to obtain the optimal condition for enhancing p-xylene selectivity. The highest p-xylene selectivity 99.7% was achieved when the amount of TEOS was 20 vol.%.The catalysts were characterized by TPD, TPO, XRF, and BET. Results show that the conversion of n-pentane was influenced remarkably by the SiO2/Al2O3 ratios of HZSM-5. The highest p-xylene selectivity 99.7% was achieved when the amount of TEOS was 20 vol.%. And cycles of deposition greatly improves HZSM-5 shape-selectivity.
Abstract: Sol-gel method has been used to fabricate
nanocomposite films on glass substrates composed halloysite clay
mineral and nanocrystalline TiO2. The methodology for the synthesis
involves a simple chemistry method utilized nonionic surfactant
molecule as pore directing agent along with the acetic acid-based solgel
route with the absence of water molecules. The thermal treatment
of composite films at 450oC ensures elimination of organic material
and lead to the formation of TiO2 nanoparticles onto the surface of
the halloysite nanotubes. Microscopy techniques and porosimetry
methods used in order to delineate the structural characteristics of the
materials. The nanocomposite films produced have no cracks and
active anatase crystal phase with small crystallite size were deposited
on halloysite nanotubes. The photocatalytic properties for the new
materials were examined for the decomposition of the Basic Blue 41
azo dye in solution. These, nanotechnology based composite films
show high efficiency for dye’s discoloration in spite of different
halloysite quantities and small amount of halloysite/TiO2 catalyst
immobilized onto glass substrates. Moreover, we examined the
modification of the halloysite/TiO2 films with silver particles in order
to improve the photocatalytic properties of the films. Indeed, the
presence of silver nanoparticles enhances the discoloration rate of the
Basic Blue 41 compared to the efficiencies obtained for unmodified
films.
Abstract: A novel interpolation scheme to extend usable spectrum
and upconvert in high performance D/A converters is addressed in this
paper. By adjusting the pulse width of cycle and the production circuit
of code, the expansion code is a null code or complementary code that
is interpolation process. What the times and codes of interpolation
decide DAC works in one of a normal mode or multi-mixer mode
so that convert the input digital data signal into normal signal or a
mixed analog signal having a mixer frequency that is higher than the
data frequency. Simulation results show that the novel scheme and
apparatus most extend the usable frequency spectrum into fifth to
sixth Nyquist zone beyond conventional DACs.
Abstract: An experiment was performed with a 24.5 MeV 14N
beam on a 12C target in the cyclotron DC-60 located in Astana,
Kazakhstan, to study the elastic scattering of 14N on 12C; the
scattering was also analyzed at different energies for tracking the
phenomenon of remarkable structure at large angles. Its aims were to
extend the measurements to very large angles, and attempt to
uniquely identify the elastic scattering potential. Good agreement
between the theoretical and experimental data has been obtained with
suitable optical potential parameters. Optical model calculations with
l -dependent imaginary potentials were also applied to the data and
relatively good agreement was found.
Abstract: The effect of Alumina nanoparticle size on thermophysical
properties, heat transfer performance and pressure loss characteristics of
Aviation Turbine Fuel (ATF)-Al2O3 nanofluids is studied experimentally for
the proposed application of regenerative cooling of semi-cryogenic rocket
engine thrust chambers. Al2O3 particles with mean diameters of 50 nm or 150
nm are dispersed in ATF. At 500C and 0.3% particle volume concentration,
the bigger particles show increases of 17% in thermal conductivity and 55% in
viscosity, whereas the smaller particles show corresponding increases of 21%
and 22% for thermal conductivity and viscosity respectively. Contrary to these
results, experiments to study the heat transfer performance and pressure loss
characteristics show that at the same pumping power, the maximum
enhancement in heat transfer coefficient at 500C and 0.3% concentration is
approximately 47% using bigger particles, whereas it is only 36% using
smaller particles.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: This paper is concerned with the design and implementation of MICOSim, an event-driven simulator written in Java for evaluating the performance of Grid entities (users, brokers and resources) under different scenarios such as varying the numbers of users, resources and brokers and varying their specifications and employed strategies.
Abstract: In this paper, 3X3 routing nodes are proposed to
provide speedup and parallel processing capability in Data Vortex
network architectures. The new design not only significantly
improves network throughput and latency, but also eliminates the
need for distributive traffic control mechanism originally embedded
among nodes and the need for nodal buffering. The cost effectiveness
is studied by a comparison study with the previously proposed 2-
input buffered networks, and considerable performance enhancement
can be achieved with similar or lower cost of hardware. Unlike
previous implementation, the network leaves small probability of
contention, therefore, the packet drop rate must be kept low for such
implementation to be feasible and attractive, and it can be achieved
with proper choice of operation conditions.
Abstract: Today-s Voltage Regulator Modules (VRMs) face increasing design challenges as the number of transistors in microprocessors increases per Moore-s Law. These challenges have recently become even more demanding as microprocessors operate at sub voltage range at significantly high current. This paper presents a new multiphase topology with cell configuration for improved performance in low voltage and high current applications. A lab scale hardware prototype of the new topology was design and constructed. Laboratory tests were performed on the proposed converter and compared with a commercially available VRM. Results from the proposed topology exhibit improved performance compared to the commercially available counterpart.
Abstract: The majority of existing predictors for time series are
model-dependent and therefore require some prior knowledge for the
identification of complex systems, usually involving system
identification, extensive training, or online adaptation in the case of
time-varying systems. Additionally, since a time series is usually
generated by complex processes such as the stock market or other
chaotic systems, identification, modeling or the online updating of
parameters can be problematic. In this paper a model-free predictor
(MFP) for a time series produced by an unknown nonlinear system or
process is derived using tracking theory. An identical derivation of the
MFP using the property of the Newton form of the interpolating
polynomial is also presented. The MFP is able to accurately predict
future values of a time series, is stable, has few tuning parameters and
is desirable for engineering applications due to its simplicity, fast
prediction speed and extremely low computational load. The
performance of the proposed MFP is demonstrated using the
prediction of the Dow Jones Industrial Average stock index.
Abstract: Nanomaterials have attracted considerable attention
during the last two decades, due to their unusual electrical, mechanical
and other physical properties as compared with their bulky
counterparts. The mechanical properties of nanostructured materials
show strong size dependency, which has been explained within the
framework of continuum mechanics by including the effects of surface
stress. The size-dependent deformations of two-dimensional
nanosized structures with surface effects are investigated in the paper
by the finite element method. Truss element is used to evaluate the
contribution of surface stress to the total potential energy and the
Gurtin and Murdoch surface stress model is implemented with
ANSYS through its user programmable features. The proposed
approach is used to investigate size-dependent stress concentration
around a nanosized circular hole and the size-dependent effective
moduli of nanoporous materials. Numerical results are compared with
available analytical results to validate the proposed modeling
approach.
Abstract: This paper compares planning results of the electricity and water generation inventory up to year 2030 in the State of
Kuwait. Currently, the generation inventory consists of oil and gas fired technologies only. The planning study considers two main cases. The first case, Reference case, examines a generation inventory based on oil and gas fired generation technologies only.
The second case examines the inclusion of renewables as part of the generation inventory under two scenarios. In the first scenario, Ref-RE, renewable build-out is based on optimum economic performance
of overall generation system. Result shows that the optimum installed
renewable capacity with electric energy generation of 11% . In the second scenario, Ref-RE20, the renewable capacity build-out is
forced to provide 20% of electric energy by 2030. The respective energy systems costs of Reference, Ref-RE and Ref-RE20 case
scenarios reach US dollar 24, 10 and 14 billion annually in 2030.
Abstract: The need of high frame-rate imaging has been triggered by the new applications of ultrasound imaging to transient elastography and real-time 3D ultrasound. Using plane wave excitation (PWE) is one of the methods to achieve very high frame-rate imaging since an image can be formed with a single insonification. However, due to the lack of transmit focusing, the image quality with PWE is lower compared with those using conventional focused transmission. To solve this problem, we propose a filter-retrieved transmit focusing (FRF) technique combined with cross-correlation weighting (FRF+CC weighting) for high frame-rate imaging with PWE. A restrospective focusing filter is designed to simultaneously minimize the predefined sidelobe energy associated with single PWE and the filter energy related to the signal-to-noise-ratio (SNR). This filter attempts to maintain the mainlobe signals and to reduce the sidelobe ones, which gives similar mainlobe signals and different sidelobes between the original PWE and the FRF baseband data. Normalized cross-correlation coefficient at zero lag is calculated to quantify the degree of similarity at each imaging point and used as a weighting matrix to the FRF baseband data to further suppress sidelobes, thus improving the filter-retrieved focusing quality.
Abstract: Knowledge capabilities are increasingly important for
the innovative technology enterprises to enhance the business
performance in terms of product competitiveness, innovation and
sales. Recognition of the company capability by auditing allows them
to further pursue advancement, strategic planning and hence gain
competitive advantages. This paper attempts to develop an
Organizations- Knowledge Capabilities Assessment (OKCA) method
to assess the knowledge capabilities of technology companies. The
OKCA is a questionnaire-based assessment tool which has been
developed to uncover the impact of various knowledge capabilities on
different organizational performance. The collected data is then
analyzed to find out the crucial elements for different technological
companies. Based on the results, innovative technology enterprises are
able to recognize the direction for further improvement on business
performance and future development plan. External environmental
factors affecting organization performance can be found through the
further analysis of some selected reference companies.
Abstract: Components of a software system may be related in a
wide variety of ways. These relationships need to be represented in
software architecture in order develop quality software. In practice, software architecture is immensely challenging, strikingly
multifaceted, extravagantly domain based, perpetually changing,
rarely cost-effective, and deceptively ambiguous. This paper analyses
relations among the major components of software systems and
argues for using several broad categories for software architecture for
assessment purposes: strongly adequate, weakly adequate and
functionally adequate software architectures among other categories.
These categories are intended for formative assessments of
architectural designs.
Abstract: In this paper, we proposed the effects of Mo thickness
on the properties of AZO/Mo/AZO multilayer thin films for
opto-electronics applications. The structural, optical and electrical
properties of AZO/Mo/AZO thin films were investigated.
Optimization of the thin films coatings resulted with low resistivity of
9.98 × 10-5 )-cm, mobility of 12.75 cm2/V-s, carrier concentration of
1.05 × 1022 cm-3, maximum transmittance of 79.13% over visible
spectrum of 380 – 780 nm and Haacke figure of merit (FOM) are 5.95
× 10-2 )-1 under Mo layer thickness of 15 nm. These results indicate an
alternative candidate for use as a transparent electrode in solar cells
and various displays applications.
Abstract: A study was conducted to determine the effect of
feeding glycerol on dairy cows performance. Twenty four Holstein
Friesian crossbred (>87.5% Holstein Friesian) lactating dairy cows in
early lactation; averaging 13+2.4 kg of milk, 64+45 days in milk,
55+16 months old and 325+26 kg live weight, were stratified for
milk yield, days in milk, age, stage of lactation and body weight, and
then randomly allocated to three treatment groups. All cows were fed
approximate 8 kg of concentrate together with ad libitum corn silage
and freely access to clean water. Nil or 150 and 300g of glycerol
were supplemented to the cows according to treatment groups. All
cows consumed similar concentrate, corn silage and total DM and
NELP. There were no significant differences in DM intake, CP intake,
NELP intake, milk and milk composition yields. All cows had similar
fat, protein, lactose, solid not fat and total solid percentage. All cows
gain similar live weight. The present study indicated that,
supplementation of glycerol did not enhance milk yield, milk
composition and live weight change.