Abstract: Cogeneration may be defined as a system which
contains electricity production and regain of the thermo value of
exhaust gases simultaneously. The examination is based on the data-s
of an active cogeneration plant. This study, it is aimed to determine
which component of the system should be revised first to raise the
efficiency and decrease the loss of exergy. For this purpose, second
law analysis of thermodynamics is applied to each component due to
consider the effects of environmental conditions and take the quality
of energy into consideration as well as the quantity of it. The exergy
balance equations are produced and exergy loss is calculated for each
component. 44,44 % loss of exergy in heat exchanger, 29,59 % in
combustion chamber, 18,68 % in steam boiler, 5,25 % in gas turbine
and 2,03 % in compressor is calculated.
Abstract: Combining energy efficiency with renewable energy
sources constitutes a key strategy for a sustainable future. The wind
power sector stands out as a fundamental element for the
achievement of the European renewable objectives and Portugal is no
exception to the increase of the wind energy for the electricity
generation. This work proposes an optimization model for the long
range electricity power planning in a system similar to the
Portuguese one, where the expected impacts of the increasing
installed wind power on the operating performance of thermal power
plants are taken into account. The main results indicate that the
increasing penetration of wind power in the electricity system will
have significant effects on the combined cycle gas power plants
operation and on the theoretically expected cost reduction and
environmental gains. This research demonstrated the need to address
the impact that energy sources with variable output may have, not
only on the short-term operational planning, but especially on the
medium to long range planning activities, in order to meet the
strategic objectives for the energy sector.
Abstract: Addis Ababa is a seat of African Union (AU), United
Nations Economic Commission for Africa (UN-ECA) and hundreds of
embassies and consular representatives. Addis Ababa is one of the
highest capitals in the world with an average 2400 meters above sea
level. It is dichotomous city with a blend of modern high-rise and
deteriorating slum quarters. Water supply and sanitation, waste
management and housing are continuing to be serious problems.
Forest wood based domestic energy use as well as uncontrolled
emissions from mobile and fixed sources has endangered the state of
the urban environment. Analysis based on satellite imagery has
revealed the deteriorating urban environment within the last three
decades. The recently restructured city administration has brought
improvements in the condition of the urban environment. However,
the overwhelming size of the challenges faced by the city dwarfed
their fairly good results.
Abstract: The direct sewage sludge application is a relative
cheap method for their liquidation. In the past heavy metal contents
increase in soils treated with sewage sludge was observed. In 2003
there was acceptance on act n.188/2003 about sewage sludge
application on soils. The basic philosophy of act is a safety of the
environmental proof of sludge application on soils. The samples of
soils from wastewater treatment plant (WTP) Poprad (35) and WTP
Michalovce (33 samples) were analyzed which were chosen for
sludge application on soils. According to the results only 14 areas for
Poprad and 25 areas for Michalovce are suitable for sludge
application according to act No. 188/2003. The application dose of
sludge was calculated 50 t.ha-1 or 75 t. ha-1 once in 5 years to ensure
that heavy metal contents in treated soils will be kept.
Abstract: Citizens are increasingly are provided with choice and
customization in public services and this has now also become a key
feature of higher education in terms of policy roll-outs on personal
development planning (PDP) and more generally as part of the
employability agenda. The goal here is to transform people, in this
case graduates, into active, responsible citizen-workers. A key part of
this rhetoric and logic is the inculcation of graduate attributes within
students. However, there has also been a concern with the issue of
student lack of engagement and perseverance with their studies. This
paper sets out to explore some of these conceptions that link graduate
attributes with citizenship as well as the notion of how identity is
forged through the higher education process. Examples are drawn
from a quality enhancement project that is being operated within the
context of the Scottish higher education system. This is further
framed within the wider context of competing and conflicting
demands on higher education, exacerbated by the current worldwide
economic climate. There are now pressures on students to develop
their employability skills as well as their capacity to engage with
global issues such as behavioural change in the light of
environmental concerns. It is argued that these pressures, in effect,
lead to a form of personalization that is concerned with how
graduates develop their sense of identity as something that is
engineered and re-engineered to meet these demands.
Abstract: Although, it is a long time that human know about
the importance of environment in life, but at the last decade of 20
century, the space that was full of hot scientific, collegial and
political were made in environmental challenge, So much that, this
problem not only disarrange the peace and security of life, but also it
has threatened human existence. One of the problems in last years
that are significant for authorities is unsatisfactory achieved results
against of using huge cost for magnificent environmental projects.
This subject leads thinker to this thought that for solving the
environmental problems it is needed new methods include of
sociology, ethics and philosophic, etc. methods apart of technical
affairs. Environment ethics is a new branch of philosophic ethics
discussion that discusses about the ethics relationship between
humans and universe that is around them. By notifying to the above
considered affairs, in today world, necessity of environmental ethics
for environment management is reduplicated. In the following the
article has been focused on environmental ethics role and
environmental management methods and techniques for developing
it.
Abstract: The quality improvements of the environmental
elements could increase the recreational opportunities in a certain
area (destination). The technique of the need for recreation focuses
on choosing certain destinations for recreational purposes. The basic
exchange taken into consideration is the one between the satisfaction
gained after staying in that area and the value expressed in money
and time allocated. The number of tourists in the respective area, the
duration of staying and the money spent including transportation
provide information on how individuals rank the place or certain
aspects of the area (such as the quality of the environmental
elements).
For the statistical analysis of the environmental benefits offered by
an area through the need of recreation technique, the following stages
are suggested:
- characterization of the reference area based on the
statistical variables considered;
- estimation of the environmental benefit through
comparing the reference area with other similar areas
(having the same environmental characteristics), from
the perspective of the statistical variables considered.
The model compared in recreation technique faced with a series of
difficulties which refers to the reference area and correct
transformation of time in money.
Abstract: The use of sewage sludge and effluents from
wastewater treatment plants for irrigation of agricultural lands is on
the rise particularly in peri-urban areas of developing countries.
The reuse of nutrients and organic matter in treated wastewater
and sewage sludge via land application is a desirable goal. However,
trace or heavy metals present in sludge pose the risk of human or
phytotoxicity from land application. Long-term use of sewage
sludge, heavy metals can accumulate to phytotoxic levels and results
in reduced plants growth and/or enhanced metal concentrations in
plants, which consumed by animals then enter the food chain. In this
research, the amount of heavy metals was measured in plants
irrigated with wastewater and sludge application. For this purpose,
three pilots were made in a Shush treatment plant in south of Tehran.
Three plants species, spinach, lettuce and radish were selected and
planted in the pilots.First pilot was irrigated just with wastewater of
treatment plant and second pilot was irrigated with wastewater and
sludge application .Third pilot was irrigated with simulated heavy
metals solution equal 50 years of irrigation. The results indicate that
the average of amount of heavy metals Pb, Cd in three plant species
in first pilot were lower than permissible limits .In second pilot,
Cadmium accumulations are high in three species plants and more
than the standard limits. Concentration of Cd , Pb have exceed their
permitted limits in plants in third pilot . It was concluded that the use
of wastewater and sludge application in agricultural lands enriched
soils with heavy metals to concentrations that may pose potential
environmental and health risks in the long-term.
Abstract: This paper reports a new application of material accounting techniques to characterise and quantify material stocks and flows at the “neighbourhood" scale. The study area is the main campus of the University of New South Wales in Sydney, Australia. The system boundary is defined by the urban structural unit (USU), a typological construct devised to facilitate assessment of the metabolism of urban systems. A streamlined material flow analysis (MFA) was applied to quantify the stocks and flows of key construction materials within the campus USU over time, drawing on empirical data from a major campus development project. The results are reviewed to assess the efficacy of the method in supporting urban environmental evaluation and design practice, for example to facilitate estimation of significant impacts such as greenhouse gas emissions. It is concluded that linking a service (in this case, teaching students) enabled by a given product (university buildings) to the amount of materials used in creating that product offers a potential way to reduce the environmental impact of that service, through more efficient use of materials.
Abstract: A phenomenological model for species spreading which incorporates the Allee effect, a species- maximum attainable growth rate, collective dispersal rate and dispersal adaptability is presented. This builds on a well-established reaction-diffusion model for spatial spreading of invading organisms. The model is phrased in terms of the “hostility" (which quantifies the Allee threshold in relation to environmental sustainability) and dispersal adaptability (which measures how a species is able to adapt its migratory response to environmental conditions). The species- invading/retreating speed and the sharpness of the invading boundary are explicitly characterised in terms of the fundamental parameters, and analysed in detail.
Abstract: The environmental performance of rapeseed oil (RO)
and rapeseed methyl ester(RME) from winter rape as fuels produced
in Romanian agroclimate is analyzed in this paper. The proposed
methodology is life cycle assessment (LCA) and takes into
consideration the influence of grain production and agroclimatic
conditions. This study shows favorable results first for RO and then
for RME. When compared to diesel fuel, both studied biofuels show
better results in the following impact categories: Abiotic depletion
potential (ADP), Ozone layer depletion (ODP) and Photochemical
ozone creation potential (POCP).Furthermore, the environmental
performance of the two biofuels studied can be improved by
changing the type of fertilizer used and also by using biofuels instead
of diesel in the field works.
Abstract: The use of contour strips of perennial vegetation with
bio-fuel potential can improve surface water quality by reducing
NO3-N and sediment outflow from cropland to surface water-bodies.
It also has economic benefits of producing ethanol. In this study,
The Soil and Water Assessment Tool (SWAT) model was applied to
a watershed in Iowa, USA to examine the effectiveness of contour
strips of switch grass in reducing the NO3-N outflows from crop
fields to rivers or lakes. Numerical experiments were conducted to
identify potential subbasins in the watershed that have high water
quality impact, and to examine the effects of strip size on NO3-N
reduction under various meteorological conditions, i.e. dry, average
and wet years. Useful information was obtained for the evaluation of
economic feasibility of growing switch grass for bio-fuel in contour
strips. The results can assist in cost-benefit analysis and decisionmaking
in best management practices for environmental protection.
Abstract: Tritium activity concentration in Danube river water
in Serbia has been determinate using a liquid scintillation counter
Quantulus 1220. During December 2010, water samples were taken
along the entire course of Danube through Serbia, from Hungarian-
Serbian to Romanian-Serbian border. This investigation is very
important because of the nearness of nuclear reactor Paks in
Hungary. Sample preparation was performed by standard test method
using Optiphase HiSafe 3 scintillation cocktail. We used a rapid
method for the preparation of environmental samples, without
electrolytic enrichment.
Abstract: Environmental studies have expanded dramatically all
over the world in the past few years. Nowadays businesses interact
with society and the environment in ways that put their mark on both
sides. Efforts improving human standard living, through the control
of nature and the development of new products, have also resulted in
contamination of the environment. Consequently companies play an
important role in environmental sustainability of a region or country.
Therefore we can say that a company's sustainable development is
strictly dependent on the environment. This article presents a fuzzy
model to evaluate a company's environmental impact. Article
illustrates an example of the automotive industry in order to prove the
usefulness of using such a model.
Abstract: The river flow forecasting represents a crucial point to employ for improving a management policy addressed to the right use of water resources as well as for conjugating prevention and defense actions against environmental degradation. The difficulties occurring during the field activities encourage the development and implementation of operative computation and measuring methods addressed to time reduction for data acquisition and processing maintaining a good level of accuracy. Therefore, the aim of the present work is to test a new entropy based expeditive methodology for the evaluation of the rating curves on three gauged sections with different geometric and morphological characteristics. The methodology requires the choice of only three verticals along the measure section and the sampling of only the maximum velocity. The results underline how in most conditions the rating curves drawn can replace those built with classic methodologies, simplifying thus the procedures of data monitoring and calculation.
Abstract: An Advance Driver Assistance System (ADAS) is a computer system on board a vehicle which is used to reduce the risk of vehicular accidents by monitoring factors relating to the driver, vehicle and environment and taking some action when a risk is identified. Much work has been done on assessing vehicle and environmental state but there is still comparatively little published work that tackles the problem of driver state. Visual attention is one such driver state. In fact, some researchers claim that lack of attention is the main cause of accidents as factors such as fatigue, alcohol or drug use, distraction and speeding all impair the driver-s capacity to pay attention to the vehicle and road conditions [1]. This seems to imply that the main cause of accidents is inappropriate driver behaviour in cases where the driver is not giving full attention while driving. The work presented in this paper proposes an ADAS system which uses an image based template matching algorithm to detect if a driver is failing to observe particular windscreen cells. This is achieved by dividing the windscreen into 24 uniform cells (4 rows of 6 columns) and matching video images of the driver-s left eye with eye-gesture templates drawn from images of the driver looking at the centre of each windscreen cell. The main contribution of this paper is to assess the accuracy of this approach using Receiver Operating Characteristic analysis. The results of our evaluation give a sensitivity value of 84.3% and a specificity value of 85.0% for the eye-gesture template approach indicating that it may be useful for driver point of regard determinations.
Abstract: This paper presents a cold chain monitoring system which focuses on assessment of quality and dynamic pricing information about food in cold chain. Cold chain is composed of many actors and stages; however it can be seen as a single entity since a breakdown in temperature control at any stage can impact the final quality of the product. In a cold chain, the shelf life, quality, and safety of perishable food throughout the supply chain is greatly impacted by environmental factors especially temperature. In this paper, a prototype application is implemented to retrieve timetemperature history, the current quality and the dynamic price setting according to changing quality impacted by temperature fluctuations in real-time.
Abstract: The fixed partial dentures are mainly used in the frontal
part of the dental arch because of their great esthetics. There are
several factors that are associated with the stress state created in
ceramic restorations, including: thickness of ceramic layers,
mechanical properties of the materials, elastic modulus of the
supporting substrate material, direction, magnitude and frequency of
applied load, size and location of occlusal contact areas, residual
stresses induced by processing or pores, restoration-cement
interfacial defects and environmental defects. The purpose of this
study is to evaluate the capability of Polarization Sensitive Optical
Coherence Tomography (PSOCT) in detection and analysis of
possible material defects in metal-ceramic and integral ceramic fixed
partial dentures. As a conclusion, it is important to have a non
invasive method to investigate fixed partial prostheses before their
insertion in the oral cavity in order to satisfy the high stress
requirements and the esthetic function.
Abstract: Discrimination between different classes of environmental
sounds is the goal of our work. The use of a sound recognition
system can offer concrete potentialities for surveillance and
security applications. The first paper contribution to this research
field is represented by a thorough investigation of the applicability
of state-of-the-art audio features in the domain of environmental
sound recognition. Additionally, a set of novel features obtained by
combining the basic parameters is introduced. The quality of the
features investigated is evaluated by a HMM-based classifier to which
a great interest was done. In fact, we propose to use a Multi-Style
training system based on HMMs: one recognizer is trained on a
database including different levels of background noises and is used
as a universal recognizer for every environment. In order to enhance
the system robustness by reducing the environmental variability, we
explore different adaptation algorithms including Maximum Likelihood
Linear Regression (MLLR), Maximum A Posteriori (MAP)
and the MAP/MLLR algorithm that combines MAP and MLLR.
Experimental evaluation shows that a rather good recognition rate
can be reached, even under important noise degradation conditions
when the system is fed by the convenient set of features.
Abstract: The problem of delay-range-dependent exponential synchronization is investigated for Lur-e master-slave systems with delay feedback control and Markovian switching. Using Lyapunov- Krasovskii functional and nonsingular M-matrix method, novel delayrange- dependent exponential synchronization in mean square criterions are established. The systems discussed in this paper is advanced system, and takes all the features of interval systems, Itˆo equations, Markovian switching, time-varying delay, as well as the environmental noise, into account. Finally, an example is given to show the validity of the main result.