Abstract: The recent growth of using multimedia transmission
over wireless communication systems, have challenges to protect the
data from lost due to wireless channel effect. Images are corrupted
due to the noise and fading when transmitted over wireless channel,
in wireless channel the image is transmitted block by block, Due to
severe fading, entire image blocks can be damaged. The aim of this
paper comes out from need to enhance the digital images at the
wireless receiver side. Proposed Boundary Interpolation (BI)
Algorithm using wavelet, have been adapted here used to
reconstruction the lost block in the image at the receiver depend on
the correlation between the lost block and its neighbors. New
Proposed technique by using Boundary Interpolation (BI) Algorithm
using wavelet with Pixel interleaver has been implemented. Pixel
interleaver work on distribute the pixel to new pixel position of
original image before transmitting the image. The block lost through
wireless channel is only effects individual pixel. The lost pixels at the
receiver side can be recovered by using Boundary Interpolation (BI)
Algorithm using wavelet. The results showed that the New proposed
algorithm boundary interpolation (BI) using wavelet with pixel
interleaver is better in term of MSE and PSNR.
Abstract: The objectives of this study are to determine the
effects of soil cover type on characteristics of leachates generated
from landfill lysimeters. Four lysimeters with diameter and height
of 0.15 and 3.00 m, respectively, were prepared. Three lysimeters
were filled with municipal waste and three different cover soil types
i.e. sandy loam soil, silty loam soil and clay soil while another
lysimeter was filled solely with municipal waste. The study was
conducted in the rainy season. Leachate quantities were measured
every day and leachate characteristics were determined once a week.
The cumulative leachate quantity from the lysimeter filled solely
with municipal waste was found to be around 27% higher than the
lysimeters using cover soils. There were no any differences of the
cumulative leachate amounts generated from the lysimeters using
three types of soils. The comparison of the total mass of pollutants
generated from all lysimeters showed that the lysimeter filled solely
with municipal waste generated the maximum quantities of
pollutants. Among the lysimeters using different types of soils, the
lysimeter using sandy loam soil generated the lowest amount of most
of pollutants, compared with the lysimeters using silty loam and clay
soils. It can be concluded that in term of pollutant attenuation in the
leachate, a sandy loam is the most suitable soil to be used as a cover
soil in the landfill.
Abstract: This contribution deals with the relationship between
communication effectiveness and the extent of communication
among organizational units. To facilitate communication between
employees and to increase the level of understanding, the knowledge
of communication tools is necessary. Recent experience has shown
that personal communication is critical for smooth running of
companies and cannot be fully replaced by any form of technical
communication devices.
Below are presented the outcomes of the research on the
relationship between the extent of communication among
organisational units and its efficiency.
Abstract: Due to the fast development of technology, the
competition of technological products is turbulent; therefore, it is
important to understand the market trend, consumers- demand and
preferences. As the smartphones are prevalent, the main purpose of
this paper is to utilize Analytic Hierarchy Process (AHP) to analyze
consumer-s purchase evaluation factors of smartphones. Through the
AHP expert questionnaire, the smartphones- main functions are
classified as “user interface", “mobile commerce functions",
“hardware and software specifications", “entertainment functions" and
“appearance and design", five aspects to analyze the weights. Then
four evaluation criteria are evaluated under each aspect to rank the
weights. Based on an analysis of data shows that consumers consider
when purchase factors are “hardware and software specifications",
“user interface", “appearance and design", “mobile commerce
functions" and “entertainment functions" in sequence. The “hardware
and software specifications" aspect obtains the weight of 33.18%; it is
the most important factor that consumers are taken into account. In
addition, the most important evaluation criteria are central processing
unit, operating system, touch screen, and battery function in sequence.
The results of the study can be adopted as reference data for mobile
phone manufacturers in the future on the design and marketing
strategy to satisfy the voice of customer.
Abstract: Successful public-private-partnership (PPP)
implementation can not be achieved without the active participation of
private sector companies. This paper examines the decision-making of
private sector companies in public works delivered by the PPP model
on the basis of social responsibility theory. It proposes that private
sector companies should indentify objectives of entering into PPP
projects, and shoulder relevant social responsibilities, while a
minimum return should also be guaranteed in their favor, so as to
compensate for their assumed risk and support them to take on
responsibilities in the future. The paper also gives a calculation
regarding the appropriate scale and reasonable degree of private sector
involvement in PPP projects through the cost-benefit analysis in a
specific case study, with the purpose to guide the private sector
companies to create a cooperation environment resembling
“symbiosis" and facilitate the smooth implementation of public works
delivered by the PPP model.
Abstract: Recent evidences on liquidity and valuation of securities in the capital markets clearly show the importance of stock market liquidity and valuation of firms. In this paper, relationship between transparency, liquidity, and valuation is studied by using data obtained from 70 companies listed in Tehran Stock Exchange during2003-2012. In this study, discriminatory earnings management, as a sign of lack of transparency and Tobin's Q, was used as the criteria of valuation. The results indicate that there is a significant and reversed relationship between earnings management and liquidity. On the other hand, there is a relationship between liquidity and transparency.The results also indicate a significant relationship between transparency and valuation. Transparency has an indirect effect on firm valuation alone or through the liquidity channel. Although the effect of transparency on the value of a firm was reduced by adding the variable of liquidity, the cumulative effect of transparency and liquidity increased.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: A study has been carried out to determine the effect of
coating two commercial glass-ionomer cements in either petroleum
jelly or wax. After coating, specimens were stored in water for 24 or
168 hours, then the coating removed and the surface examined.
Coating in wax was found to increase the surface hardness
significantly compared with the uncoated control, whereas coating
the specimens in petroleum jelly led to only a slight increase in
surface hardness. Coating in wax led to no detectable ion release
after either 24 or 168 hours, though there was some ion release after
the coating had been removed and the specimens exposed to water
for a further 24 hours. This shows that soluble species remained in
these specimens. Overall, this study confirms the idea that immature
glass-ionomers should be protected from early exposure to moisture,
and that the protection offered by petroleum jelly is only modest.
Abstract: The demand for new telecommunication services requiring higher capacities, data rates and different operating modes have motivated the development of new generation multi-standard wireless transceivers. A multi-standard design often involves extensive system level analysis and architectural partitioning, typically requiring extensive calculations. In this research, a decimation filter design tool for wireless communication standards consisting of GSM, WCDMA, WLANa, WLANb, WLANg and WiMAX is developed in MATLAB® using GUIDE environment for visual analysis. The user can select a required wireless communication standard, and obtain the corresponding multistage decimation filter implementation using this toolbox. The toolbox helps the user or design engineer to perform a quick design and analysis of decimation filter for multiple standards without doing extensive calculation of the underlying methods.
Abstract: Small signal stability causes small perturbations in the
generator that can cause instability in the power network. It is
generally known that small signal stability are directly related to the
generator and load properties. This paper examines the effects of
generator input variations on power system oscillations for a small
signal stability study. Eigenvaules and eigenvectors are used to
examine the stability of the power system. The dynamic power
system's mathematical model is constructed and thus calculated using
load flow and small signal stability toolbox on MATLAB. The power
system model is based on a 3-machine 9-bus system that was
modified to suit this study. In this paper, Participation Factors are a
means to gauge the effects of variation in generation with other
parameters on the network are also incorporated.
Abstract: The mixing behaviors of dry and wet granular
materials in gas fluidized bed systems were investigated
computationally using the combined Computational Fluid Dynamics
and Discrete Element Method (CFD-DEM). Dry particles were
observed to mix fairly rapidly during the fluidization process due to
vigorous relative motions between particles induced by the flow of
gas. In contrast, due to the presence of strong cohesive forces arising
from capillary liquid bridges between wet particles, the mixing
efficiencies of wet granular materials under similar operating
conditions were observed to be reduced significantly.
Abstract: This paper presents the approach to design the Auto-
Tuning PID controller for interactive Water Level Process using
integral step response. The Integral Step Response (ISR) is the
method to model a dynamic process which can be done easily,
conveniently and very efficiently. Therefore this method is advantage
for design the auto tune PID controller. Our scheme uses the root
locus technique to design PID controller. In this paper MATLAB is
used for modeling and testing of the control system. The
experimental results of the interacting water level process can be
satisfyingly illustrated the transient response and the steady state
response.
Abstract: In this paper optimization of routing in ad-hoc
networks is surveyed and a new method for reducing the complexity
of routing algorithms is suggested. Using binary matrices for each
node in the network and updating it once the routing is done, helps
nodes to stop repeating the routing protocols in each data transfer.
The algorithm suggested can reduce the complexity of routing to the
least amount possible.
Abstract: Simulation of occlusal function during laboratory
material-s testing becomes essential in predicting long-term
performance before clinical usage. The aim of the study was to assess
the influence of chamfer preparation depth on failure risk of heat
pressed ceramic crowns with and without zirconia framework by
means of finite element analysis. 3D models of maxillary central
incisor, prepared for full ceramic crowns with different depths of the
chamfer margin (between 0.8 and 1.2 mm) and 6-degree tapered
walls together with the overlying crowns were generated using
literature data (Fig. 1, 2). The crowns were designed with and
without a zirconia framework with a thickness of 0.4 mm. For all
preparations and crowns, stresses in the pressed ceramic crown,
zirconia framework, pressed ceramic veneer, and dentin were
evaluated separately. The highest stresses were registered in the
dentin. The depth of the preparations had no significant influence on
the stress values of the teeth and pressed ceramics for the studied
cases, only for the zirconia framework. The zirconia framework
decreases the stress values in the veneer.
Abstract: This paper proposes an architectural and graphical
user interface (GUI) design of a traditional Thai musical instrument
application for tablet computers for practicing “Ranaad Ek" which is
a trough-resonated keyboard percussion instrument. The application
provides percussion methods for a player as real as a physical
instrument. The application consists of two playing modes. The first
mode is free playing, a player can freely multi touches on wooden bar
to produce instrument sounds. The second mode is practicing mode
that guilds the player to follow percussions and rhythms of practice
songs. The application has achieved requirements and specifications.
Abstract: In this paper we canvass three case studies of unique
research partnerships between universities and schools in the wider
community. In doing so, we consider those areas of indeterminate
zones of professional practice explored by academics in their
research activities within the wider community. We discuss three
cases: an artist-in-residence program designed to engage primary
school children with new understandings about local Indigenous
Australian issues in their pedagogical and physical landscapes; an
assessment of pedagogical concerns in relation to the use of physical
space in classrooms; and the pedagogical underpinnings of a
costumed museum school program. In doing so, we engage issues of
research as playing an integral part in the development,
implementation and maintenance of academic engagements with
wider community issues.
Abstract: The aim of this paper is to discuss a low-cost methodology that can predict traffic flow conflicts and quantitatively rank crash expectancies (based on relative probability) for various traffic facilities. This paper focuses on the application of statistical distributions to model traffic flow and Monte Carlo techniques to simulate traffic and discusses how to create a tool in order to predict the possibility of a traffic crash. A low-cost data collection methodology has been discussed for the heterogeneous traffic flow that exists and a GIS platform has been proposed to thematically represent traffic flow from simulations and the probability of a crash. Furthermore, discussions have been made to reflect the dynamism of the model in reference to its adaptability, adequacy, economy, and efficiency to ensure adoption.
Abstract: The design of high-rise building is more often dictated
by its serviceability rather than strength. Structural Engineers are
always striving to overcome challenge of controlling lateral
deflection and storey drifts as well as self weight of structure
imposed on foundation.
One of the most effective techniques is the use of outrigger and
belt truss system in Composite structures that can astutely solve the
above two issues in High-rise constructions.
This paper investigates deflection control by effective utilisation
of belt truss and outrigger system on a 60-storey composite building
subjected to wind loads. A three dimensional Finite Element Analysis
is performed with one, two and three outrigger levels. The reductions
in lateral deflection are 34%, 42% and 51% respectively as compared
to a model without any outrigger system. There is an appreciable
decline in the storey drifts with the introduction of these stiffer
arrangements.
Abstract: In hypersonic environments, the aerothermal effect
makes it difficult for the optical side windows of optical guided
missiles to withstand high heat. This produces cracking or breaking,
resulting in an inability to function. This study used computational
fluid mechanics to investigate the external cooling jet conditions of
optical side windows. The turbulent models k-ε and k-ω were
simulated. To be in better accord with actual aerothermal
environments, a thermal radiation model was added to examine
suitable amounts of external coolants and the optical window
problems of aero-thermodynamics. The simulation results indicate that
when there are no external cooling jets, because airflow on the optical
window and the tail groove produce vortices, the temperatures in these
two locations reach a peak of approximately 1600 K. When the
external cooling jets worked at 0.15 kg/s, the surface temperature of
the optical windows dropped to approximately 280 K. When adding
thermal radiation conditions, because heat flux dissipation was faster,
the surface temperature of the optical windows fell from 280 K to
approximately 260 K. The difference in influence of the different
turbulence models k-ε and k-ω on optical window surface temperature
was not significant.
Abstract: Expression and secretion of inflammation markers are
disturbed in obesity. Interleukin-6 reduces body fat mass. The
common G-174C polymorphism in the promoter of IL-6 gene has
been reported that effects on transcriptional regulation. The objective
was to investigate association of the common polymorphism G-174C
with obesity in Iranian population. The present study is cross
sectional association study that included 242 individuals (110 men
and 132 women). Serum IL-6 levels, C-reactive protein, fasting
blood glucose and blood lipids profile were measured .BMI and
WHR were calculated. Genotyping is carried out by PCR and RFLP.
The frequencies of G and C allele were 64.5% and 35.5%,
respectively. The G-174C polymorphism was not associated with
BMI and WHR. However in obese individual, fasting blood glucose
was significantly higher in carrier of C allele compared with the noncarrier.
The IL-6 G-174C polymorphism is not a risk factor for
obesity in Iranian population.