Abstract: This paper describes a prototype aircraft that can fly
slowly, safely and transmit wireless video for tasks like reconnaissance,
surveillance and target acquisition. The aircraft is designed to
fly in closed quarters like forests, buildings, caves and tunnels which
are often spacious but GPS reception is poor. Envisioned is that a
small, safe and slow flying vehicle can assist in performing dull,
dangerous and dirty tasks like disaster mitigation, search-and-rescue
and structural damage assessment.
Abstract: Streaming Applications usually run in parallel or in
series that incrementally transform a stream of input data. It poses a
design challenge to break such an application into distinguishable
blocks and then to map them into independent hardware processing
elements. For this, there is required a generic controller that
automatically maps such a stream of data into independent processing
elements without any dependencies and manual considerations. In
this paper, Kahn Process Networks (KPN) for such streaming
applications is designed and developed that will be mapped on
MPSoC. This is designed in such a way that there is a generic Cbased
compiler that will take the mapping specifications as an input
from the user and then it will automate these design constraints and
automatically generate the synthesized RTL optimized code for
specified application.
Abstract: This paper examines and compares several of the most common real time methods. These methods are CORE, YSM, MASCOT, JSD, DARTS, RTSAD, ADARTS, CODARTS, HOOD, HRT-HOOD, ROOM, UML, UML-RT. The methods are compared using attributes like i) usability, ii) compositionality and iii) proper RT notations available. Finally some comparison results are given and discussed.
Abstract: This paper presents the optimal design and development
of an axial flux motor for blood pump application. With the design
objective of maximizing the motor efficiency and torque, different
topologies of AFPM machine has been examined. Selection of
optimal magnet fraction, Halbach arrangement of rotor magnets and
the use of Soft Magnetic Composite (SMC) material for the stator
core results in a novel motor with improved efficiency and torque
profile. The results of the 3D Finite element analysis for the novel
motor have been shown.
Abstract: Market based models are frequently used in the resource
allocation on the computational grid. However, as the size of
the grid grows, it becomes difficult for the customer to negotiate
directly with all the providers. Middle agents are introduced to
mediate between the providers and customers and facilitate the
resource allocation process. The most frequently deployed middle
agents are the matchmakers and the brokers. The matchmaking agent
finds possible candidate providers who can satisfy the requirements
of the consumers, after which the customer directly negotiates with
the candidates. The broker agents are mediating the negotiation with
the providers in real time.
In this paper we present a new type of middle agent, the marketmaker.
Its operation is based on two parallel operations - through
the investment process the marketmaker is acquiring resources and
resource reservations in large quantities, while through the resale process
it sells them to the customers. The operation of the marketmaker
is based on the fact that through its global view of the grid it can
perform a more efficient resource allocation than the one possible in
one-to-one negotiations between the customers and providers.
We present the operation and algorithms governing the operation
of the marketmaker agent, contrasting it with the matchmaker and
broker agents. Through a series of simulations in the task oriented
domain we compare the operation of the three agents types. We find
that the use of marketmaker agent leads to a better performance in the
allocation of large tasks and a significant reduction of the messaging
overhead.
Abstract: In this paper, genetic algorithm (GA) is proposed for
the design of an optimization algorithm to achieve the bandwidth
allocation of ATM network. In Broadband ISDN, the ATM is a highbandwidth;
fast packet switching and multiplexing technique. Using
ATM it can be flexibly reconfigure the network and reassign the
bandwidth to meet the requirements of all types of services. By
dynamically routing the traffic and adjusting the bandwidth
assignment, the average packet delay of the whole network can be
reduced to a minimum. M/M/1 model can be used to analyze the
performance.
Abstract: Attachment of the circulating monocytes to the
endothelium is the earliest detectable events during formation of
atherosclerosis. The adhesion molecules, chemokines and matrix
proteases genes were identified to be expressed in atherogenesis.
Expressions of these genes may influence structural integrity of the
luminal endothelium. The aim of this study is to relate changes in the
ultrastructural morphology of the aortic luminal surface and gene
expressions of the endothelial surface, chemokine and MMP-12 in
normal and hypercholesterolemic rabbits. Luminal endothelial
surface from rabbit aortic tissue was examined by scanning electron
microscopy (SEM) using low vacuum mode to ascertain
ultrastructural changes in development of atherosclerotic lesion. Gene
expression of adhesion molecules, MCP-1 and MMP-12 were studied
by Real-time PCR. Ultrastructural observations of the aortic luminal
surface exhibited changes from normal regular smooth intact
endothelium to irregular luminal surface including marked globular
appearance and ruptures of the membrane layer. Real-time PCR
demonstrated differentially expressed of studied genes in
atherosclerotic tissues. The appearance of ultrastructural changes in
aortic tissue of hypercholesterolemic rabbits is suggested to have
relation with underlying changes of endothelial surface molecules,
chemokine and MMP-12 gene expressions.
Abstract: This paper presents a method for determining the
uniaxial tensile properties such as Young-s modulus, yield strength
and the flow behaviour of a material in a virtually non-destructive
manner. To achieve this, a new dumb-bell shaped miniature
specimen has been designed. This helps in avoiding the removal of
large size material samples from the in-service component for the
evaluation of current material properties. The proposed miniature
specimen has an advantage in finite element modelling with respect
to computational time and memory space. Test fixtures have been
developed to enable the tension tests on the miniature specimen in a
testing machine. The studies have been conducted in a chromium
(H11) steel and an aluminum alloy (AR66). The output from the
miniature test viz. load-elongation diagram is obtained and the finite
element simulation of the test is carried out using a 2D plane stress
analysis. The results are compared with the experimental results. It is
observed that the results from the finite element simulation
corroborate well with the miniature test results. The approach seems
to have potential to predict the mechanical properties of the
materials, which could be used in remaining life estimation of the
various in-service structures.
Abstract: This paper describes new computer vision algorithms
that have been developed to track moving objects as part of a
long-term study into the design of (semi-)autonomous vehicles. We
present the results of a study to exploit variable kernels for tracking in
video sequences. The basis of our work is the mean shift
object-tracking algorithm; for a moving target, it is usual to define a
rectangular target window in an initial frame, and then process the data
within that window to separate the tracked object from the background
by the mean shift segmentation algorithm. Rather than use the
standard, Epanechnikov kernel, we have used a kernel weighted by the
Chamfer distance transform to improve the accuracy of target
representation and localization, minimising the distance between the
two distributions in RGB color space using the Bhattacharyya
coefficient. Experimental results show the improved tracking
capability and versatility of the algorithm in comparison with results
using the standard kernel. These algorithms are incorporated as part of
a robot test-bed architecture which has been used to demonstrate their
effectiveness.
Abstract: In this paper, a multi-agent robot system is presented. The system consists of four robots. The developed robots are able to automatically enter and patrol a harmful environment, such as the building infected with virus or the factory with leaking hazardous gas. Further, every robot is able to perform obstacle avoidance and search for the victims. Several operation modes are designed: remote control, obstacle avoidance, automatic searching, and so on.
Abstract: The paper proposes the novel design of a 3T XOR gate combining complementary CMOS with pass transistor logic. The design has been compared with earlier proposed 4T and 6T XOR gates and a significant improvement in silicon area and power-delay product has been obtained. An eight transistor full adder has been designed using the proposed three-transistor XOR gate and its performance has been investigated using 0.15um and 0.35um technologies. Compared to the earlier designed 10 transistor full adder, the proposed adder shows a significant improvement in silicon area and power delay product. The whole simulation has been carried out using HSPICE.
Abstract: The paper describes the evaluation of quality of
control for cases of controlled non-minimal phase plants. Control
circuits containing non-minimal phase plants have different
properties, they manifest reversed reaction at the beginning of unit
step response. For these types of plants are developed special
criterion of quality of control, which considers the difference and can
be helpful for synthesis of optimal controller tuning. All results are
clearly presented using Matlab/Simulink models.
Abstract: In a bi-fuel diesel engine, the carburetor plays a vital
role in switching from fuel gas to petrol mode operation and viceversa.
The carburetor is the most important part of the fuel system of
a diesel engine. All diesel engines carry variable venturi mixer
carburetors. The basic operation of the carburetor mainly depends on
the restriction barrel called the venturi. When air flows through the
venturi, its speed increases and its pressure decreases. The main
challenge focuses on designing a mixing device which mixes the
supplied gas is the incoming air at an optimum ratio. In order to
surmount the identified problems, the way fuel gas and air flow in
the mixer have to be analyzed. In this case, the Computational Fluid
Dynamics or CFD approach is applied in design of the prototype
mixer. The present work is aimed at further understanding of the air
and fuel flow structure by performing CFD studies using a software
code. In this study for mixing air and gas in the condition that has
been mentioned in continuance, some mixers have been designed.
Then using of computational fluid dynamics, the optimum mixer has
been selected. The results indicated that mixer with 12 holes can
produce a homogenous mixture than those of 8-holes and 6-holes
mixer. Also the result showed that if inlet convergency was smoother
than outlet divergency, the mixture get more homogenous, the reason
of that is in increasing turbulence in outlet divergency.
Abstract: This article describes design of the 8-bit asynchronous
microcontroller simulation model in VHDL. The model is created in
ISE Foundation design tool and simulated in Modelsim tool. This
model is a simple application example of asynchronous systems
designed in synchronous design tools. The design process of creating
asynchronous system with 4-phase bundled-data protocol and with
matching delays is described in the article. The model is described in
gate-level abstraction.
The simulation waveform of the functional construction is the
result of this article. Described construction covers only the
simulation model. The next step would be creating synthesizable
model to FPGA.
Abstract: Most paddy rice fields in East Asia are small parcels,
and the weather conditions during the growing season are usually
cloudy. FORMOSAT-2 multi-spectral images have an 8-meter
resolution and one-day recurrence, ideal for mapping paddy rice fields
in East Asia. To map rice fields, this study first determined the
transplanting and the most active tillering stages of paddy rice and
then used multi-temporal images to distinguish different growing
characteristics between paddy rice and other ground covers. The
unsupervised ISODATA (iterative self-organizing data analysis
techniques) and supervised maximum likelihood were both used to
discriminate paddy rice fields, with training areas automatically
derived from ten-year cultivation parcels in Taiwan. Besides original
bands in multi-spectral images, we also generated normalized
difference vegetation index and experimented with object-based
pre-classification and post-classification. This paper discusses results
of different image classification methods in an attempt to find a
precise and automatic solution to mapping paddy rice in Taiwan.
Abstract: Purpose of this work is to develop an automatic classification system that could be useful for radiologists in the breast cancer investigation. The software has been designed in the framework of the MAGIC-5 collaboration. In an automatic classification system the suspicious regions with high probability to include a lesion are extracted from the image as regions of interest (ROIs). Each ROI is characterized by some features based generally on morphological lesion differences. A study in the space features representation is made and some classifiers are tested to distinguish the pathological regions from the healthy ones. The results provided in terms of sensitivity and specificity will be presented through the ROC (Receiver Operating Characteristic) curves. In particular the best performances are obtained with the Neural Networks in comparison with the K-Nearest Neighbours and the Support Vector Machine: The Radial Basis Function supply the best results with 0.89 ± 0.01 of area under ROC curve but similar results are obtained with the Probabilistic Neural Network and a Multi Layer Perceptron.
Abstract: TiO2 supported nano-ZnO catalyst was prepared by
deposition-precipitation and tested for the trans-esterification
reaction of soybean oil to biodiesel. The TiO2 support stabilized the
nano-ZnO in a dispersed form with limited crystallite size compared
to the unsupported ZnO. The final ZnO dispersion and crystallite size
and the material transfer resistance in the catalyst significantly
influenced the supported nano-ZnO catalyst performance.
Abstract: This paper presents the fundamentals of Origami engineering and its application in nowadays as well as future industry. Several main cores of mathematical approaches such as Huzita- Hatori axioms, Maekawa and Kawasaki-s theorems are introduced briefly. Meanwhile flaps and circle packing by Robert Lang is explained to make understood the underlying principles in designing crease pattern. Rigid origami and its corrugation patterns which are potentially applicable for creating transformable or temporary spaces is discussed to show the transition of origami from paper to thick material. Moreover, some innovative applications of origami such as eyeglass, origami stent and high tech origami based on mentioned theories and principles are showcased in section III; while some updated origami technology such as Vacuumatics, self-folding of polymer sheets and programmable matter folding which could greatlyenhance origami structureare demonstrated in Section IV to offer more insight in future origami.
Abstract: This paper describes vibration analysis using the finite
element method for a small earphone, especially for the diaphragm
shape with a low-rigidity. The viscoelastic diaphragm is supported by
multiple nonlinear concentrated springs with linear hysteresis
damping. The restoring forces of the nonlinear springs have cubic
nonlinearity. The finite elements for the nonlinear springs with
hysteresis are expressed and are connected to the diaphragm that is
modeled by linear solid finite elements in consideration of a complex
modulus of elasticity. Further, the discretized equations in physical
coordinates are transformed into the nonlinear ordinary coupled
equations using normal coordinates corresponding to the linear natural
modes. We computed the nonlinear stationary and non-stationary
responses due to the internal resonance between modes with large
amplitude in the nonlinear springs and elastic modes in the diaphragm.
The non-stationary motions are confirmed as the chaos due to the
maximum Lyapunov exponents with a positive number. From the time
histories of the deformation distribution in the chaotic vibration, we
identified nonlinear modal couplings.
Abstract: This paper presented a proposed design for
transcutaneous inductive powering links. The design used to transfer
power and data to the implanted devices such as implanted
Microsystems to stimulate and monitoring the nerves and muscles.
The system operated with low band frequency 13.56 MHZ according
to industrial- scientific – medical (ISM) band to avoid the tissue
heating. For external part, the modulation index is 13 % and the
modulation rate 7.3% with data rate 1 Mbit/s assuming Tbit=1us. The
system has been designed using 0.35-μm fabricated CMOS
technology. The mathematical model is given and the design is
simulated using OrCAD P Spice 16.2 software tool and for real-time
simulation the electronic workbench MULISIM 11 has been used.
The novel circular plane (pancake) coils was simulated using
ANSOFT- HFss software.