Abstract: This paper describes the design of a voltage based maximum power point tracker (MPPT) for photovoltaic (PV) applications. Of the various MPPT methods, the voltage based method is considered to be the simplest and cost effective. The major disadvantage of this method is that the PV array is disconnected from the load for the sampling of its open circuit voltage, which inevitably results in power loss. Another disadvantage, in case of rapid irradiance variation, is that if the duration between two successive samplings, called the sampling period, is too long there is a considerable loss. This is because the output voltage of the PV array follows the unchanged reference during one sampling period. Once a maximum power point (MPP) is tracked and a change in irradiation occurs between two successive samplings, then the new MPP is not tracked until the next sampling of the PV array voltage. This paper proposes an MPPT circuit in which the sampling interval of the PV array voltage, and the sampling period have been shortened. The sample and hold circuit has also been simplified. The proposed circuit does not utilize a microcontroller or a digital signal processor and is thus suitable for low cost and low power applications.
Abstract: The robot is a repeated task plant. The control of such
a plant under parameter variations and load disturbances is one of the
important problems. The aim of this work is to design Geno-Fuzzy
controller suitable for online applications to control single link rigid
robot arm plant. The genetic-fuzzy online controller (indirect
controller) has two genetic-fuzzy blocks, the first as controller, the
second as identifier. The identification method is based on inverse
identification technique. The proposed controller it tested in normal
and load disturbance conditions.
Abstract: A study has been carried out to determine the effect of
coating two commercial glass-ionomer cements in either petroleum
jelly or wax. After coating, specimens were stored in water for 24 or
168 hours, then the coating removed and the surface examined.
Coating in wax was found to increase the surface hardness
significantly compared with the uncoated control, whereas coating
the specimens in petroleum jelly led to only a slight increase in
surface hardness. Coating in wax led to no detectable ion release
after either 24 or 168 hours, though there was some ion release after
the coating had been removed and the specimens exposed to water
for a further 24 hours. This shows that soluble species remained in
these specimens. Overall, this study confirms the idea that immature
glass-ionomers should be protected from early exposure to moisture,
and that the protection offered by petroleum jelly is only modest.
Abstract: The demand for new telecommunication services requiring higher capacities, data rates and different operating modes have motivated the development of new generation multi-standard wireless transceivers. A multi-standard design often involves extensive system level analysis and architectural partitioning, typically requiring extensive calculations. In this research, a decimation filter design tool for wireless communication standards consisting of GSM, WCDMA, WLANa, WLANb, WLANg and WiMAX is developed in MATLAB® using GUIDE environment for visual analysis. The user can select a required wireless communication standard, and obtain the corresponding multistage decimation filter implementation using this toolbox. The toolbox helps the user or design engineer to perform a quick design and analysis of decimation filter for multiple standards without doing extensive calculation of the underlying methods.
Abstract: In this paper we present a novel design of a wearable
electronic textile. After defining a special application, we used the
specifications of some low power, tiny elements including sensors,
microcontrollers, transceivers, and a fault tolerant special topology to
have the most reliability as well as low power consumption and
longer lifetime. We have considered two different conditions as
normal and bodily critical conditions and set priorities for using
different sensors in various conditions to have a longer effective
lifetime.
Abstract: Ground-level tropospheric ozone is one of the air
pollutants of most concern. It is mainly produced by photochemical
processes involving nitrogen oxides and volatile organic compounds
in the lower parts of the atmosphere. Ozone levels become
particularly high in regions close to high ozone precursor emissions
and during summer, when stagnant meteorological conditions with
high insolation and high temperatures are common.
In this work, some results of a study about urban ozone
distribution patterns in the city of Badajoz, which is the largest and
most industrialized city in Extremadura region (southwest Spain) are
shown. Fourteen sampling campaigns, at least one per month, were
carried out to measure ambient air ozone concentrations, during
periods that were selected according to favourable conditions to
ozone production, using an automatic portable analyzer.
Later, to evaluate the ozone distribution at the city, the measured
ozone data were analyzed using geostatistical techniques. Thus, first,
during the exploratory analysis of data, it was revealed that they were
distributed normally, which is a desirable property for the subsequent
stages of the geostatistical study. Secondly, during the structural
analysis of data, theoretical spherical models provided the best fit for
all monthly experimental variograms. The parameters of these
variograms (sill, range and nugget) revealed that the maximum
distance of spatial dependence is between 302-790 m and the
variable, air ozone concentration, is not evenly distributed in reduced
distances. Finally, predictive ozone maps were derived for all points
of the experimental study area, by use of geostatistical algorithms
(kriging). High prediction accuracy was obtained in all cases as
cross-validation showed. Useful information for hazard assessment
was also provided when probability maps, based on kriging
interpolation and kriging standard deviation, were produced.
Abstract: This paper presents the approach to design the Auto-
Tuning PID controller for interactive Water Level Process using
integral step response. The Integral Step Response (ISR) is the
method to model a dynamic process which can be done easily,
conveniently and very efficiently. Therefore this method is advantage
for design the auto tune PID controller. Our scheme uses the root
locus technique to design PID controller. In this paper MATLAB is
used for modeling and testing of the control system. The
experimental results of the interacting water level process can be
satisfyingly illustrated the transient response and the steady state
response.
Abstract: Software testability is proposed to address the problem of increasing cost of test and the quality of software. Testability measure provides a quantified way to denote the testability of software. Since 1990s, many testability measure models are proposed to address the problem. By discussing the contradiction between domain testability and domain range ratio (DRR), a new testability measure, semantic fault distance, is proposed. Its validity is discussed.
Abstract: In this paper optimization of routing in ad-hoc
networks is surveyed and a new method for reducing the complexity
of routing algorithms is suggested. Using binary matrices for each
node in the network and updating it once the routing is done, helps
nodes to stop repeating the routing protocols in each data transfer.
The algorithm suggested can reduce the complexity of routing to the
least amount possible.
Abstract: Simulation of occlusal function during laboratory
material-s testing becomes essential in predicting long-term
performance before clinical usage. The aim of the study was to assess
the influence of chamfer preparation depth on failure risk of heat
pressed ceramic crowns with and without zirconia framework by
means of finite element analysis. 3D models of maxillary central
incisor, prepared for full ceramic crowns with different depths of the
chamfer margin (between 0.8 and 1.2 mm) and 6-degree tapered
walls together with the overlying crowns were generated using
literature data (Fig. 1, 2). The crowns were designed with and
without a zirconia framework with a thickness of 0.4 mm. For all
preparations and crowns, stresses in the pressed ceramic crown,
zirconia framework, pressed ceramic veneer, and dentin were
evaluated separately. The highest stresses were registered in the
dentin. The depth of the preparations had no significant influence on
the stress values of the teeth and pressed ceramics for the studied
cases, only for the zirconia framework. The zirconia framework
decreases the stress values in the veneer.
Abstract: In this paper, a fractional-order FIR differentiator
design method using the differential evolution (DE) algorithm is
presented. In the proposed method, the FIR digital filter is designed to
meet the frequency response of a desired fractal-order differentiator,
which is evaluated in the frequency domain. To verify the design
performance, another design method considered in the time-domain is
also provided. Simulation results reveal the efficiency of the proposed
method.
Abstract: This paper proposes an architectural and graphical
user interface (GUI) design of a traditional Thai musical instrument
application for tablet computers for practicing “Ranaad Ek" which is
a trough-resonated keyboard percussion instrument. The application
provides percussion methods for a player as real as a physical
instrument. The application consists of two playing modes. The first
mode is free playing, a player can freely multi touches on wooden bar
to produce instrument sounds. The second mode is practicing mode
that guilds the player to follow percussions and rhythms of practice
songs. The application has achieved requirements and specifications.
Abstract: In this paper, the use of beam search and look-ahead strategies for solving the strip packing problem (SPP) is investigated. Given a strip of fixed width W, unlimited length L, and a set of n circular pieces of known radii, the objective is to determine the minimum length of the initial strip that packs all the pieces. An augmented algorithm which combines beam search and a look-ahead strategies is proposed. The look-ahead is used in order to evaluate the nodes at each level of the tree search. The best nodes are then retained for branching. The computational investigation showed that the proposed augmented algorithm is able to improve the best known solutions of the literature on most instances used.
Abstract: Bacterial magnetic nanoparticles have great useful potential in biotechnological and biomedical applications. In this study, a liquid growth medium was modified for cultivation a fastidious magnetotactic bacterium that has been isolated from Anzali
lagoon, Iran in our previous research. These modifications include
change in vitamin, mineral, carbon sources and etcetera. In our
experience, the serum bottles and designed air-tight laboratory bottles
were used to create microaerobic conditions in order to development
of a method for scale-up experiment. This information may serve as a
guide to green chemistry based biological protocols for the synthesis
of magnetic nanoparticles with control over the chemical
composition, morphology and size.
Abstract: In this paper we canvass three case studies of unique
research partnerships between universities and schools in the wider
community. In doing so, we consider those areas of indeterminate
zones of professional practice explored by academics in their
research activities within the wider community. We discuss three
cases: an artist-in-residence program designed to engage primary
school children with new understandings about local Indigenous
Australian issues in their pedagogical and physical landscapes; an
assessment of pedagogical concerns in relation to the use of physical
space in classrooms; and the pedagogical underpinnings of a
costumed museum school program. In doing so, we engage issues of
research as playing an integral part in the development,
implementation and maintenance of academic engagements with
wider community issues.
Abstract: This paper presents a studyof the impact of reference
node locations on the accuracy of the indoor positioning systems. In
particular, we analyze the localization accuracy of the RSSI database
mapping techniques, deploying on the IEEE 802.15.4 wireless
networks. The results show that the locations of the reference nodes
used in the positioning systems affect the signal propagation
characteristics in the service area. Thisin turn affects the accuracy of the wireless indoor positioning system. We found that suitable
location of reference nodes could reduce the positioning error upto 35 %.
Abstract: In this paper we intend to ascertain the state of the art on multifingered end-effectors, also known as robotic hands or dexterous robot hands, and propose an experimental setup for an innovative task based design approach, involving cutting edge technologies in motion capture. After an initial description of the capabilities and complexity of a human hand when grasping objects, in order to point out the importance of replicating it, we analyze the mechanical and kinematical structure of some important works carried out all around the world in the last three decades and also review the actuators and sensing technologies used. Finally we describe a new design philosophy proposing an experimental setup for the first stage using recent developments in human body motion capture systems that might lead to lighter and always more dexterous robotic hands.
Abstract: One part of the total employee-s reward is apart from basic wages or salary, employee-s benefits and intangible elements also so called contingent (variable) pay. Contingent pay is connected to performance, contribution, capcompetency or skills of individual employees, and to team-s or company-wide performance or to combination of few of the mentioned possibilities. Main aim of this article is to define, based on available information, contingent pay, describe reasons for its implementation and arguments for and against this type of remuneration, but also bring information not only about its extent and level of utilization by organizations of the Czech Republic operating in the field of environmental protection, but also mention their practical experience with this type of remuneration.
Abstract: The design of high-rise building is more often dictated
by its serviceability rather than strength. Structural Engineers are
always striving to overcome challenge of controlling lateral
deflection and storey drifts as well as self weight of structure
imposed on foundation.
One of the most effective techniques is the use of outrigger and
belt truss system in Composite structures that can astutely solve the
above two issues in High-rise constructions.
This paper investigates deflection control by effective utilisation
of belt truss and outrigger system on a 60-storey composite building
subjected to wind loads. A three dimensional Finite Element Analysis
is performed with one, two and three outrigger levels. The reductions
in lateral deflection are 34%, 42% and 51% respectively as compared
to a model without any outrigger system. There is an appreciable
decline in the storey drifts with the introduction of these stiffer
arrangements.
Abstract: Recently, the design is becoming important in product development. The technology which is a strong point of Japan is immediately caught up by the foreign countries, and the price competition begins. Therefore companies tend to plan differentiation of products by the design or a color. The purpose of my work was to consider the optimal color for using by product development. We needed to clarify the thing leading to color preference for this purpose. Two kinds of investigations were made. By the first investigation, we found out that a geographical factor difference existed in color preference. Then, investigation which regarded the difference as latitude was conducted. However, the result expected from the difference in latitude was not obtained. It seems that it is necessary to set up difference of latitude a little more greatly, or to reexamine by other geographical factors.