Abstract: Ice cover County has a significant impact on rivers as it affects with the ice melting capacity which results in flooding, restrict navigation, modify the ecosystem and microclimate. River ices are made up of different ice types with varying ice thickness, so surveillance of river ice plays an important role. River ice types are captured using infrared imaging camera which captures the images even during the night times. In this paper the river ice infrared texture images are analysed using first-order statistical methods and secondorder statistical methods. The second order statistical methods considered are spatial gray level dependence method, gray level run length method and gray level difference method. The performance of the feature extraction methods are evaluated by using Probabilistic Neural Network classifier and it is found that the first-order statistical method and second-order statistical method yields low accuracy. So the features extracted from the first-order statistical method and second-order statistical method are combined and it is observed that the result of these combined features (First order statistical method + gray level run length method) provides higher accuracy when compared with the features from the first-order statistical method and second-order statistical method alone.
Abstract: This paper describes Nano-particle based Planar Laser
Scattering (NPLS) flow visualization of angled supersonic jets into a
supersonic cross flow based on the HYpersonic Low TEmperature
(HYLTE) nozzle which was widely used in DF chemical laser. In
order to investigate the non-reacting flowfield in the HYLTE nozzle, a
testing section with windows was designed and manufactured. The
impact of secondary fluids orifice separation on mixing was examined.
For narrow separation of orifices, the secondary fuel penetration
increased obviously compared to diluent injection, which means
smaller separation of diluent and fuel orifices would enhance the
mixing of fuel and oxidant. Secondary injections with angles of 30, 40
and 50 degrees were studied. It was found that the injectant
penetration increased as the injection angle increased, while the
interfacial surface area to entrain the freestream fluid is largest when
the injection angle is 40 degree.
Abstract: Photo-BJMOSFET (Bipolar Junction Metal-Oxide-
Semiconductor Field Effect Transistor) fabricated on SOI film was proposed. ITO film is adopted in the device as gate electrode to reduce
light absorption. Depletion region but not inversion region is formed
in film by applying gate voltage (but low reverse voltage) to achieve
high photo-to-dark-current ratio. Comparisons of photoelectriccharacteristics
executed among VGK=0V, 0.3V, 0.6V, 0.9V and 1.0V
(reverse voltage VAK is equal to 1.0V for total area of 10×10μm2). The
results indicate that the greatest improvement in photo-to-dark-current
ratio is achieved up to 2.38 at VGK=0.6V. In addition,
photo-BJMOSFET is compatible with CMOS integration due to big
input resistance
Abstract: Anti-money laundering is commonly recognized as a
set of procedures, laws or regulations designed to reduce the practice
of generating income through illegal actions. In Malaysia, the
government and law enforcement agencies have stepped up their
capacities and efforts to curb money laundering since 2001. One of
these measures was the enactment of the Anti-Money Laundering
Act (AMLA) in 2001. The implementation costs on anti-money
laundering requirements (AMLR) can be burdensome to those who
are involved in enforcing them. The objective of this paper is to
explore the perceived effectiveness of AMLR from the enforcement
agencies- perspective. This is a preliminary study whose findings
will help to give direction for further AML research in Malaysia. In
addition, the results of this study provide empirical evidences on the
perceived effectiveness of AMLR prior to further investigations on
barriers and improvements of the implementation of the anti-money
laundering regime in Malaysia.
Abstract: The major source of allergy in home is the house dust
mite (Dematophagoides farina, Dermatophagoides pteronyssinus)
causing allergic symptom include atopic dermatitis, asthma, perennial
rhinitis and even infant death syndrome.
Control of this mite species is dependent on the use of chemical
methods such as fumigation treatments with methylene bromide,
spraying with organophosphates such as pirimiphos-methyl, or
treatments with repellents such as DEET and benzyl benzoate.
Although effective, their repeated use for decades has sometimes
resulted in development of resistance and fostered environmental and
human health concerns. Both decomposing animal parts and the
protein that surrounds mite fecal pellets cause mite allergy. So it is
more effective to repel than to kill them because allergen is not living
house dust mite but dead body or fecal particles of house dust mite.
It is important to find out natural repellent material against house
dust mite to control them and reduce the allergic reactions. Plants may
be an alternative source for dust mite control because they contain a
range of bioactive chemicals.
The research objectives of this paper were to verify the acaricidal
and repellent effects of cinnamon essential oil and to find out it-s most
effective concentrations. We could find that cinnamon bark essential
oil was very effective material to control the house dust mite.
Furthermore, it could reduce chemical resistance and danger for
human health.
Abstract: Contact centres have been exemplars of scientific management in the discipline of operations management for more than a decade now. With the movement of industries from a resource based economy to knowledge based economy businesses have started to realize the customer eccentricity being the key to sustainability amidst high velocity of the market. However, as technologies have converged and advanced, so have the contact centres. Contact Centres have redirected the supply chains and the concept of retailing is highly diminished due to over exaggeration of cost reduction strategies. In conditions of high environmental velocity together with services featuring considerable information intensity contact centres will require up to date and enlightened agents to satisfy the demands placed upon them by those requesting their services. In this paper we examine salient factors such as Power Distance, Knowledge structures and the dynamics of job specialisation and enlargement to suggest critical success factors in the domain of contact centres.
Abstract: Single crystals of Magnesium alloys such as pure Mg,
Mg-1Zn-0.5Y, Mg-0.1Y, and Mg-0.1Ce alloys were successfully
fabricated in this study by employing the modified Bridgman method.
To determine the exact orientation of crystals, pole figure
measurement using X-ray diffraction were carried out on each single
crystal. Hardness and compression tests were conducted followed by
subsequent recrysatllization annealing. Recrystallization kinetics of
Mg alloy single crystals has been investigated. Fabricated single
crystals were cut into rectangular shaped specimen and solution
treated at 400oC for 24 hrs, and then deformed in compression mode
by 30% reduction. Annealing treatment for recrystallization has been
conducted on these cold-rolled plates at temperatures of 300oC for
various times from 1 to 20 mins. The microstructure observation and
hardness measurement conducted on the recrystallized specimens
revealed that static recrystallization of ternary alloy single crystal was
very slow, while recrystallization behavior of binary alloy single
crystals appeared to be very fast.
Abstract: In this paper the application of rule mining in order to
review the effective factors on supplier selection is reviewed in the
following three sections 1) criteria selecting and information
gathering 2) performing association rule mining 3) validation and
constituting rule base. Afterwards a few of applications of rule base
is explained. Then, a numerical example is presented and analyzed
by Clementine software. Some of extracted rules as well as the
results are presented at the end.
Abstract: As data to be stored in storage subsystems
tremendously increases, data protection techniques have become more
important than ever, to provide data availability and reliability. In this
paper, we present the file system-based data protection (WOWSnap)
that has been implemented using WORM (Write-Once-Read-Many)
scheme. In the WOWSnap, once WORM files have been created, only
the privileged read requests to them are allowed to protect data against
any intentional/accidental intrusions. Furthermore, all WORM files
are related to their protection cycle that is a time period during which
WORM files should securely be protected. Once their protection cycle
is expired, the WORM files are automatically moved to the
general-purpose data section without any user interference. This
prevents the WORM data section from being consumed by
unnecessary files. We evaluated the performance of WOWSnap on
Linux cluster.
Abstract: This paper aims at numerically analysing the effect
of an active flow control (AFC) by a vortex generator jet (VGJ)
submerged in a boundary layer via Chimera Grids and Detached-
Eddy Simulation (DES). The performance of DES results are
judged against Reynolds-Averaged Navier-Stokes (RANS) and
compared with the experiments that showed an unsteady vortex
motion downstream of VGJ. Experimental results showed that
the mechanism of embedding logitudinal vortex structure in the
main stream flow is quite effective in increasing the near wall
momentum of separated aircraft wing. In order to simulate such
a flow configuration together with the VGJ, an efficient numerical
approach is required. This requirement is fulfilled by performing
the DES simulation over the flat plate using the DLR TAU Code.
The DES predictions identify the vortex region via smooth hybrid
length scale and predict the unsteady vortex motion observed in
the experiments. The DES results also showed that the sufficient
grid refinement in the vortex region resolves the turbulent scales
downstream of the VGJ, the spatial vortex core postion and nondimensional
momentum coefficient RVx .
Abstract: The aerodynamic stall control of a baseline 13-percent
thick NASA GA(W)-2 airfoil using a synthetic jet actuator (SJA) is
presented in this paper. Unsteady Reynolds-averaged Navier-Stokes
equations are solved on a hybrid grid using a commercial software to
simulate the effects of a synthetic jet actuator located at 13% of the
chord from the leading edge at a Reynolds number Re = 2.1x106 and
incidence angles from 16 to 22 degrees. The experimental data for the
pressure distribution at Re = 3x106 and aerodynamic coefficients at
Re = 2.1x106 (angle of attack varied from -16 to 22 degrees) without
SJA is compared with the computational fluid dynamic (CFD)
simulation as a baseline validation. A good agreement of the CFD
simulations is obtained for aerodynamic coefficients and pressure
distribution.
A working SJA has been integrated with the baseline airfoil and
initial focus is on the aerodynamic stall control at angles of attack
from 16 to 22 degrees. The results show a noticeable improvement in
the aerodynamic performance with increase in lift and decrease in
drag at these post stall regimes.
Abstract: Providing authentication for the messages exchanged
between group members in addition to confidentiality is an important
issue in Secure Group communication. We develop a protocol for
Secure Authentic Communication where we address authentication
for the group communication scheme proposed by Blundo et al.
which only provides confidentiality. Authentication scheme used is a
multiparty authentication scheme which allows all the users in the
system to send and receive messages simultaneously. Our scheme is
secure against colluding malicious parties numbering fewer than k.
Abstract: The aim of this study was to test whether the Attention
Networks Test (ANT) showed temporal decrements in performance.
Vigilance tasks typically show such decrements, which may reflect
impairments in executive control resulting from cognitive fatigue.
The ANT assesses executive control, as well as alerting and
orienting. Thus, it was hypothesized that ANT executive control
would deteriorate over time. Manipulations including task condition
(trial composition) and masking were included in the experimental
design in an attempt to increase performance decrements. However,
results showed that there is no temporal decrement on the ANT. The
roles of task demands, cognitive fatigue and participant motivation in
producing this result are discussed. The ANT may not be an effective
tool for investigating temporal decrement in attention.
Abstract: Agropyron cristatum L. Gaertn. is a native grass of
semiarid region in Iran which is quit resistant to cool and drought
climate and withstand heavy grazing. This species has close
phylogenetic relationship with Triticum and Hordeum. In this
research, the effect of seven different concentrations of growth
regulator 2,4-D on callus production and somatic embryogenesis of
A. cristatum was investigated on Murashige and Skoog medium. The
results showed that the rate of callus, embryo and neomorph were
highest in 1 mg L-1 2,4-D. Callus production was increased in 1 mg
L-1 2,4-D but dramatically decreased at 5.5 and 9 mg L-1 2,4-D. The
somatic embryos were observed at 1 and 4 mg L-1 2,4-D but matured
embryos and plantlet were only occurred at 1 mg L-1 2,4-D. There
were significant differences between 1 mg L-1 2,4-D and other
treatments for producing globular and torpedo embryos, plantlet,
rooted callus and number of roots (p
Abstract: It is well known that metallic particles reduce the
reliability of Gas-Insulated Substation (GIS) equipments by initiating
partial discharge (PDs) that can lead to breakdown and complete
failure of GIS. This paper investigates the characteristics of PDs
caused by metallic particle adhering to the solid spacer. The PD
detection and measurement were carried out by using IEC 60270
method with particles of different sizes and at different positions on
the spacer surface. The results show that a particle of certain size at
certain position possesses a unique PD characteristic as compared to
those caused by particles of different sizes and/or at different
positions. Therefore PD characteristics may be useful for the particle
size and position identification.
Abstract: Today technological process makes possible surface
control of producing parts which is needful for product quality
guarantee. Geometrical structure of part surface includes form,
proportion, accuracy to shape, accuracy to size, alignment and
surface topography (roughness, waviness, etc.). All these parameters
are dependence at technology, production machine parameters,
material properties, but also at human, etc. Every parameters
approves at total part accuracy, it is means at accuracy to shape. One
of the most important accuracy to shape element is roundness. This
paper will be deals by comparison of roughness deviations at
coordination measuring machines and at special single purpose
machines. Will describing measuring by discreet method
(discontinuous) and scanning method (continuous) at coordination
measuring machines and confrontation with reference method using
at single purpose machines.
Abstract: We introduce an extended resource leveling model that abstracts real life projects that consider specific work ranges for each resource. Contrary to traditional resource leveling problems this model considers scarce resources and multiple objectives: the minimization of the project makespan and the leveling of each resource usage over time. We formulate this model as a multiobjective optimization problem and we propose a multiobjective genetic algorithm-based solver to optimize it. This solver consists in a two-stage process: a main stage where we obtain non-dominated solutions for all the objectives, and a postprocessing stage where we seek to specifically improve the resource leveling of these solutions. We propose an intelligent encoding for the solver that allows including domain specific knowledge in the solving mechanism. The chosen encoding proves to be effective to solve leveling problems with scarce resources and multiple objectives. The outcome of the proposed solvers represent optimized trade-offs (alternatives) that can be later evaluated by a decision maker, this multi-solution approach represents an advantage over the traditional single solution approach. We compare the proposed solver with state-of-art resource leveling methods and we report competitive and performing results.
Abstract: Cooling with sound is a physical phenomenon allowed by Thermo-Acoustics in which acoustic energy is transformed into a negative heat transfer, in other words: into cooling! Without needing any harmful gas, the transformation is environmentally friendly and can respond to many needs in terms of air conditioning, food refrigeration for domestic use, and cooling medical samples for example. To explore the possibilities of this cooling solution on a small scale, the TACS prototype has been designed, consisting of a low cost thermoacoustic refrigerant “pipe” able to lower the temperature by a few degrees. The obtained results are providing an interesting element for possible future of thermo-acoustic refrigeration.
Abstract: This paper presents an automated inspection algorithm
for a thick plate. Thick plates typically have various types of surface
defects, such as scabs, scratches, and roller marks. These defects have
individual characteristics including brightness and shape. Therefore, it
is not simple to detect all the defects. In order to solve these problems
and to detect defects more effectively, we propose a dual light
switching lighting method and a defect detection algorithm based on
Gabor filters.
Abstract: Development of a Robust Supply Chain for Dynamic
Operating Environment as we move further into the twenty first
century, organisations are under increasing pressure to deliver a high
product variation at a reasonable cost without compromise in quality.
In a number of cases this will take the form of a customised or high
variety low volume manufacturing system that requires prudent
management of resources, among a number of functions, to achieve
competitive advantage. Purchasing and Supply Chain management is
one of such function and due to the substantial interaction with
external elements needs to be strategically managed. This requires a
number of primary and supporting tools that will enable the
appropriate decisions to be made rapidly. This capability is
especially vital in a dynamic environment as it provides a pivotal role
in increasing the profit margin of the product. The management of
this function can be challenging by itself and even more for Small
and Medium Enterprises (SMEs) due to the limited resources and
expertise available at their disposal.
This paper discusses the development of tools and concepts
towards effectively managing the purchasing and supply chain
function. The developed tools and concepts will provide a cost
effective way of managing this function within SMEs. The paper
further shows the use of these tools within Contechs, a manufacturer
of luxury boat interiors, and the associated benefits achieved as a
result of this implementation. Finally a generic framework towards
use in such environments is presented.