Abstract: In this paper a genetic algorithm (GA) with dual-fitness function is proposed and applied to solve the deterministic identical machine scheduling problem. The mating fitness function value was used to determine the mating for chromosomes, while the selection fitness function value was used to determine their survivals. The performance of this algorithm was tested on deterministic identical machine scheduling using simulated data. The results obtained from the proposed GA were compared with classical GA and integer programming (IP). Results showed that dual-fitness function GA outperformed the classical single-fitness function GA with statistical significance for large problems and was competitive to IP, particularly when large size problems were used.
Abstract: Force sensor has been used as requisite for knowing information on the amount and the directions of forces on the skin surface. We have developed a four-degrees-of-freedom capacitive force sensor (approximately 20×20×5 mm3) that has a flexible structure and sixteen parallel plate capacitors. An iterative algorithm was developed for estimating four displacements from the sixteen capacitances using fourth-order polynomial approximation of characteristics between capacitance and displacement. The estimation results from measured capacitances had large error caused by deterioration of the characteristics. In this study, effective capacitors had major information were selected on the basis of the capacitance change range and the characteristic shape. Maximum errors in calibration and non-calibration points were 25%and 6.8%.However the maximum error was larger than desired value, the smallness of averaged value indicated the occurrence of a few large error points. On the other hand, error in non-calibration point was within desired value.
Abstract: The purpose of the research is to investigate the energetic feature of the backpack load on soldier’s gait with variation of the trunk flexion angle. It is believed that the trunk flexion variation of the loaded gait may cause a significant difference in the energy cost which is often in practice in daily life. To this end, seven healthy Korea military personnel participated in the experiment and are tested under three different walking postures comprised of the small, natural and large trunk flexion. There are around 5 degree differences of waist angle between each trunk flexion. The ground reaction forces were collected from the force plates and motion kinematic data are measured by the motion capture system. Based on these data, the impulses, momentums and mechanical works done on the center of body mass (COM) during the double support phase were computed. The result shows that the push-off and heel strike impulse are not relevant to the trunk flexion change, however the mechanical work by the push-off and heel strike were changed by the trunk flexion variation. It is because the vertical velocity of the COM during the double support phase is increased significantly with an increase in the trunk flexion. Therefore, we can know that the gait efficiency of the loaded gait depends on the trunk flexion angle. Also, even though the gravitational impulse and pre-collision momentum are changed by the trunk flexion variation, the after-collision momentum is almost constant regardless of the trunk flexion variation.
Abstract: Microorganisms can be removed, inhibited or killed by physical agents, physical processes or chemical agents but they have their inherent disadvantages such as increased resistance against antibiotics etc. Since, plants have endless ability to synthesize aromatic substances which act as the master agents for plant defense mechanisms against microorganisms, insects and herbivores. Thus, secondary metabolites or phytochemicals obtained from plants can be used as agents of disease control nowadays. In the present study effect of different concentrations of acetone fraction of leaves and alcohol fraction of inflorescence of Euphorbia pulcherrima on various cytomorphological parameters i.e. cell number, mycelium width, conidial size, conidiophore size etc. of Aspergillus fumigatus has been studied. Change in mycelium/ hyphal cell width, conidium size, conidiophore size etc. was measured with the help of a previously calibrated oculometer. To study effect on morphology, fungal mycelium along with conidiophore and conidia were stained with cotton blue and mounted in lactophenol and observed microscopically. Inhibitory action of the acetone extract of Euphorbia pulcherrima leaf on growth of Aspergillus fumigatus was investigated. Control containing extract free medium supported profuse growth of the fungus. Although decrease in growth was observed even at 3.95μg/ml but significant inhibition of growth was started at7.81μg/ml concentration of the extract. Complete inhibition was observed at 15.62μg/ml and above. Microscopic examination revealed that at 3.95, 7.81 and 15.62μg/ml extract concentration hyphal cell width was found to be increased from 1.44μm in control to 3.86, 5.24 and 8.98 μm respectively giving a beaded appearance to the mycelium. Vesicle size was reduced from 24.78x20.08μm (control) to 11.34x10.06μm at 3.95μg/ml concentration. At 7.81 and 15.62μg/ml concentration no phialides and sterigmata were observed. Inhibitory action of the alcohol extract of inflorescence on the growth of Aspergillus fumigatus was also studied. Control containing extract free medium supported profuse growth of the fungus. Although decrease in growth was observed even at 3.95μg/ml but complete inhibition was observed at 62.5μg/ml and above. Microscopic examination revealed that hyphal cell width of Aspergillus fumigatus was found to be increased from 1.67μm in control to 5.84μm at MIC i.e. at 62.5μg/ml. Vesicle size was reduced from 44.76x 24.22μm (control) to 11.36x 6.80μm at 15.62μg/ml concentrations. At 31.25 μg/ml and 62.5μg/ml concentration no phialides and sterigmata was found. Spore germination was completely found to be inhibited at 3.95μg/ml concentration. Similarly 92.87% reduction in vesicle size was observed at 15.62μg/ml concentration. It is evident from the results that plant extracts inhibit fungal growth and this inhibition is concentration dependent.
Abstract: The purpose of this paper is to examine co-creation of non-economic values in Islamic banking services and their significance for service science by comparing Islamic and conventional banking services. Although many scholars have discussed co-creation of values in services, most of them have focused on only economic values.
Following Sharia (Islamic principles that are based on Qur’an and Sunnah) traditions, Islamic banking is more concerned with such non-economic values as well-being, partnership, fairness, trust, and justice, than such economic values as money in terms of interest. Therefore, it may be more sustainable and suitable for today’s unpredictable socio-economic environments.
We also argue that Islamic banking is essentially a value co-creation business model that fits better with the so-called Service-Dominant Logic (SDL) than conventional banking. This paper explores a new frontier of value co-creation in services, thereby contributing to further development of service science.
Abstract: Different vegetable oil based biodiesel (FAMES) were prepared by alkaline transesterification using refined oils as well as waste frying oil (WFO). Methanol and sodium hydroxide are used as catalyst under similar reaction conditions. To ensure the quality of biodiesel produced, a series of different ASTM Standard tests were carried out. In this context, various testwere done including viscosity, carbon residue, specific gravity, corrosion test, flash point, cloud point and pour point. Results revealed that characteristics of biodiesel depend on the feedstock and it is far better than petroleum diesel.
Abstract: The exponential increase in the volume of medical image database has imposed new challenges to clinical routine in maintaining patient history, diagnosis, treatment and monitoring. With the advent of data mining and machine learning techniques it is possible to automate and/or assist physicians in clinical diagnosis. In this research a medical image classification framework using data mining techniques is proposed. It involves feature extraction, feature selection, feature discretization and classification. In the classification phase, the performance of the traditional kNN k nearest neighbor classifier is improved using a feature weighting scheme and a distance weighted voting instead of simple majority voting. Feature weights are calculated using the interestingness measures used in association rule mining. Experiments on the retinal fundus images show that the proposed framework improves the classification accuracy of traditional kNN from 78.57 % to 92.85 %.
Abstract: In this paper we use low frequency noise analysis to understand and map the current conduction path in a multi gate junctionless FinFET. The device used in this study behaves as a gated resistor and shows excellent short channel effect suppression due to its multi gate structure. Generally for a bulk conduction device like the junctionless device studied in this work, the low frequency noise can be modelled using the mobility fluctuation model; however for this device we can also see the effect of carrier fluctuations on the LFN characteristic. The noise characteristic at different gate bias and also the possible location of the traps is explained.
Abstract: Darcy’s Law is a well-known constitutive equation describing the flow of a fluid through a porous medium. The equation shows a relationship between the superficial or Darcy velocity and the pressure gradient which was first experimentally observed by Henry Darcy in 1855-1856. In this study, we apply homogenization method to Stokes equation in order to derive Darcy’s Law. The process of deriving the equation is complicated, especially in multidimensional domain. Thus, for the sake of simplicity, we use the indicial notation as well as the homogenization. This combination provides a smooth, simple and easy technique to derive Darcy’s Law.
Abstract: The reproductive aging of women is a biological process which is expressed by the loss of ovarian function and therefore the loss of the possibility of procreation. The present work aims to evaluate the effect of menopause on sexual health of rural women and to examine the determinants of female sexuality after menopause. A survey was conducted among 527 women in the rural area of Marrakech. The average age of women was 51.92 ± 7.24 years. It appears from this study that sexual activity in menopausal women decreases with age, 20% of women had no sexual activity after menopause. 72% of respondents reported having sex by obligation, 71% of women say they are not satisfied with their sexuality, while 29 % are very satisfied. The most common sexual complaints are represented by the decreased libido (81%), vaginal dryness (54%), and pain (22,7%). Of the 511 women with sexual dysfunction, only 34 (6, 4%) consulted for this disorder. Many factors may influence sex include menopause and all the biological changes but also the roles of culture, social constructions and perception of sexuality after menopause are complicated.
Abstract: In this study, artificial limestone brick samples are produced by using wood sawdust wastes (WSW) having different grades of sizes and limestone powder waste (LPW). The thermo-elastic properties of produced brick samples in various WSW amounts are investigated. At 30% WSW replacement with LPW in the brick sample the thermal conductivity value is effectively reduced and the reduction in the thermal conductivity value of brick sample at 30% WSW replacement with LPW is about 38.9% as compared with control sample. The energy conservation in buildings by using LPW and WSW in masonry brick material production having low thermal conductivity reduces energy requirements. A strong relationship is also found among the thermal conductivity, unit weight and ultrasonic pulse velocity values of brick samples produced. It shows a potential to be used for walls, wooden board substitute, alternative to the concrete blocks, ceiling panels, sound barrier panels, absorption materials etc.
Abstract: Customer audits are generally used to ensure customer
that supplier is continuously able to meet his requirements while
supplying him required products and services. However, customer
audits can be considered as a very useful quality control tool for
suppliers as well. In our paper, we analyzed the process of customer
audits realized in Czech companies from both perspectives: a
supplier´s viewpoint and customer´s viewpoint. At the end, we tried
to emphasize some areas that should not be omitted during the audit
process.
Abstract: The influence of copper and zinc supplements on milk
production performances and health indicators was tested in a 20-
week feeding trial, with 40 Holstein-Friesian lactating cows, devided
in four groups (copper, zinc, copper-zinc and control). Correlations of
the Cu and Zn plasma values with some animal performance criteria
of health (body condition score and somatic cell counts) and
production (milk yield, peak milk yield, fat and crude protein
content) were done. During the 140 days of the experiment, the two
added minerals caused a statistically significant increase (p < 0.05) of
their plasma values after the peak of the cows’ lactations. It was also
observed that subjects that have received copper and zinc
supplements had the lowest number of somatic cell counts in milk.
The Pearson correlation test showed a positive corellation (p = 0.007,
r = + 0.851) between the plasma Zn and the milk production. The
improvement of the nutritional status improved the milk production
performances of the cows as well as their health performances.
Abstract: Ergonomics is a useful tool for creating a healthy and
safe workplace. The long-term action of harmful conditions on the
health of workers is the emergence of occupational disease, and the
firm-s increased compensation costs associated with these diseases,
but is also the loss of time needed for educating and including new
workers in the work process. The article deals with the link of
ergonomics to occupational diseases, factors which influence these
diseases. In the conclusion, a model is described to help reduce the
risk of selected occupational diseases using ergonomic principles and
knowledge.
Abstract: In biomedical implant field, a new formula is given
for the study of Radio Frequency power attenuation by simultaneous
effects of side and angular misalignment of the supply/data transfer
coils. A confrontation with the practical measurements done into a
Faraday cage, allowed a checking of the obtained theoretical results.
The DC supply systems without material connection and the data
transmitters used in the case of biomedical implants, can be well
dimensioned by taking into account the possibility of power
attenuation by misalignment of transfer coils
Abstract: This paper explains a novel approach to human interactive e-learning systems using head posture images. Students- face and hair information are used to identify a human presence and estimate the gaze direction. We then define the human-computer interaction level and test the definition using ten students and seventy different posture images. The experimental results show that head posture images provide adequate information for increasing human-computer interaction in e-learning systems.
Abstract: Image registration is the process of establishing point
by point correspondence between images obtained from a same
scene. This process is very useful in remote sensing, medicine,
cartography, computer vision, etc. Then, the task of registration is to
place the data into a common reference frame by estimating the
transformations between the data sets. In this work, we develop a
rigid point registration method based on the application of genetic
algorithms and Hausdorff distance. First, we extract the feature points
from both images based on the algorithm of global and local
curvature corner. After refining the feature points, we use Hausdorff
distance as similarity measure between the two data sets and for
optimizing the search space we use genetic algorithms to achieve
high computation speed for its inertial parallel. The results show the
efficiency of this method for registration of satellite images.
Abstract: This paper addresses the analysis of the interference between complementary ground component (CGC) base station and mobile earth station (MES). In the frequency sharing scenario between CGC base station and MES, the interference from the adjacent beams must be considered. In this paper, we estimated the interference to MES of an integrated satellite system and the result is presented as the carrier to interference ratio(C/I) with respect to the number of CGC base station in the adjacent beam and the ratio of satellite beam center radius to the total beam radius (R1/R). By using these results, we can determine the minimum separation distance between the CGC base stations of adjacent beam and MES for compatibility. This result can be applied to the CGC base station of an integrated satellite system for the effective frequency sharing.
Abstract: Development of microprocessor controlled sensor for measurement of wind speed and direction is the aim of this study. Electrical circuits and software were developed to the existing electromechanical part of the sensor TM-W2 becoming the properties of so-called smart sensor. The measured data about wind speed (sensitivity 0.01 m/s) and direction (0-360° by step 10°) are transmitted as 16-bit information. The connection between sensor and control unit is realized by radio communication (FM 433 MHz). Transition range is 220 m if used Quad type antenna. This concept provides substitution of actual cable systems by wireless ones.
Abstract: This paper presents the study of strengthening R/C
beams with large circular and square opening located at flexure zone
by Carbon Fiber Reinforced Polymer (CFRP) laminates. A total of
five beams were tested to failure under four point loading to
investigate the structural behavior including crack patterns, failure
mode, ultimate load and load deflection behaviour. Test results show
that large opening at flexure reduces the beam capacity and stiffness;
and increases cracking and deflection. A strengthening configuration
was designed for each un-strengthened beams based on their
respective crack patterns. CFRP laminates remarkably restore the
beam capacity of beam with large circular opening at flexure location
while 10% re-gain of beam capacity with square opening. The use of
CFRP laminates with the designed strengthening configuration could
significantly reduce excessive cracking and deflection and increase
the ultimate capacity and stiffness of beam.