Abstract: In recent years, there have been attempts to store
natural gas in adsorptive form. This is called adsorptive natural gas,
or ANG. The problem with this technology is the low sorption
capacity. The purpose is to achieve compressed natural gas (CNG)
capacity of 230 V/V. Further research is required to achieve such
target. Several research studies have been performed with this target;
through either the modification or development of new sorbents or
the optimization of the operation sorption process itself. In this work,
storage of methane on molecular sieves 5A and 13X was studied on
dry basis, and on wet basis to certain extent. The temperature and the
pressure dynamics were investigated. The results indicated that
regardless of the charge pressure, the time for the peak temperature
during the methane charge process is always the same. This can be
used as a characteristic of the adsorbent. The total achieved
deliveries using molecular sieves were much lower than that of
activated carbons; 53.0 V/V for the case of 13X molecular sieves and
43 V/V for the case of 5A molecular sieves, both at 2oC and 4 MPa
(580 psi). Investigation of charge pressure dynamic using wet
molecular sieves at 2oC and a mass ratio of 0.5, revealed slowness of
the process and unexpected behavior.
Abstract: The purpose of this study was to determine the most satisfying and frustrating aspects of ICT (Information and Communications Technologies) teaching in Turkish schools. Another aim was to compare these aspects based-on ICT teachers- selfefficacy. Participants were 119 ICT teachers from different geographical areas of Turkey. Participants were asked to list salient satisfying and frustrating aspects of ICT teaching, and to fill out the Self-Efficacy Scale for ICT Teachers. Results showed that the high self-efficacy teachers listed more positive and negative aspects of ICT teaching then did the low self-efficacy teachers. The satisfying aspects of ICT teaching were the dynamic nature of ICT subject, higher student interest, having opportunity to help other subject teachers, and lecturing in well-equipped labs, whereas the most frequently cited frustrating aspects of ICT teaching were ICT-related extra works of schools and colleagues, shortages of hardware and technical problems, indifferent students, insufficient teaching time, and the status of ICT subject in school curriculum. This information could be useful in redesigning ICT teachers- roles and responsibilities as well as job environment in schools.
Abstract: It has been shown that a load discontinuity at the end of
an impulse will result in an extra impulse and hence an extra amplitude
distortion if a step-by-step integration method is employed to yield the
shock response. In order to overcome this difficulty, three remedies
are proposed to reduce the extra amplitude distortion. The first remedy
is to solve the momentum equation of motion instead of the force
equation of motion in the step-by-step solution of the shock response,
where an external momentum is used in the solution of the momentum
equation of motion. Since the external momentum is a resultant of the
time integration of external force, the problem of load discontinuity
will automatically disappear. The second remedy is to perform a single
small time step immediately upon termination of the applied impulse
while the other time steps can still be conducted by using the time step
determined from general considerations. This is because that the extra
impulse caused by a load discontinuity at the end of an impulse is
almost linearly proportional to the step size. Finally, the third remedy
is to use the average value of the two different values at the integration
point of the load discontinuity to replace the use of one of them for
loading input. The basic motivation of this remedy originates from the
concept of no loading input error associated with the integration point
of load discontinuity. The feasibility of the three remedies are
analytically explained and numerically illustrated.
Abstract: The aim of this study is to determine the basic information and communication technology (ICT) skills that may be needed by students studying in the 8th grade of the primary education in their cooperative project works implemented via the Internet. Within the scope of the study, the curriculum used for European Computer Driving License (ECDL) and the curriculum used in Turkey are also compared in terms of the ability to use ICT, which is aimed to be provided to the students. The research population of the study, during which the pre test – post test control group experimental model was used, consisted of 40 students from three different schools. In the first stage of the study, the skills that might be needed by students for their cooperative project works implemented via the Internet were determined through examination of the completed Comenious, e – twinning and WorldLinks projects. In the second stage of the study, the curriculums of the Turkish Ministry of National Education (MEB) and ECDL were evaluated by seven different teachers in line with these skills. Also in this study the ECDL and MEB curriculums were compared in terms of capability to provide the skills to implement cooperative projects via the Internet. In line with the findings of the study, the skills that might be needed by students to implement cooperative projects via the Internet were outlined, and existence of a significant difference was established in favor of the ECDL curriculum upon comparison of both curriculums in accordance with this outline (U = 50,500; p
Abstract: Persian (Farsi) script is totally cursive and each character is written in several different forms depending on its former and later characters in the word. These complexities make automatic handwriting recognition of Persian a very hard problem and there are few contributions trying to work it out. This paper presents a novel practical approach to online recognition of Persian handwriting which is based on representation of inputs and patterns with very simple visual features and comparison of these simple terms. This recognition approach is tested over a set of Persian words and the results have been quite acceptable when the possible words where unknown and they were almost all correct in cases that the words where chosen from a prespecified list.
Abstract: CO2 miscible displacement is not feasible in many oil fields due to high reservoir temperature as higher pressure is required to achieve miscibility. The miscibility pressure is far higher than the formation fracture pressure making it impossible to have CO2 miscible displacement. However, by using oleophilic chemicals, minimum miscibility pressure (MMP) could be lowered. The main objective of this research is to find the best oleophilic chemical in MMP reduction using slim-tube test and Vanishing Interfacial Tension (VIT) The chemicals are selected based on the characteristics that it must be oil soluble, low water solubility, have 4 – 8 carbons, semi polar, economical, and safe for human operation. The families of chemicals chosen are carboxylic acid, alcohol, and ketone. The whole experiment would be conducted at 100°C and the best chemical is said to be effective when it is able to lower CO2-crude oil MMP the most. Findings of this research would have great impact to the oil and gas industry in reduction of operation cost for CO2EOR which is applicable to both onshore and offshore operation.
Abstract: Recently, genetic algorithms (GA) and particle swarm optimization (PSO) technique have attracted considerable attention among various modern heuristic optimization techniques. Since the two approaches are supposed to find a solution to a given objective function but employ different strategies and computational effort, it is appropriate to compare their performance. This paper presents the application and performance comparison of PSO and GA optimization techniques, for Thyristor Controlled Series Compensator (TCSC)-based controller design. The design objective is to enhance the power system stability. The design problem of the FACTS-based controller is formulated as an optimization problem and both the PSO and GA optimization techniques are employed to search for optimal controller parameters. The performance of both optimization techniques in terms of computational time and convergence rate is compared. Further, the optimized controllers are tested on a weakly connected power system subjected to different disturbances, and their performance is compared with the conventional power system stabilizer (CPSS). The eigenvalue analysis and non-linear simulation results are presented and compared to show the effectiveness of both the techniques in designing a TCSC-based controller, to enhance power system stability.
Abstract: This study employs auto-regressive distributed lag (ARDL) bounds approach to cointegration for long run and errorcorrection modeling (ECM) for short run analysis to examine the relationship between revenue gap and economic growth for Pakistan using annual time series data over the period 1980 to 2008. The short and long run results indicate that revenue gap is statistical significant and negatively effect economic growth. The significant and negative coefficient of error correction term in ECM indicates that after a shock, the long rum equilibrium will again converge towards equilibrium about 10.406 percent within a year.
Abstract: The objective of this study is to investigate the effect of adding coal to obtain insulating ceramic product. The preparation of mixtures is achieved with 04 types of different masse compositions, consisting of gray and yellow clay, and coal. Analyses are performed on local raw materials by adding coal as additive. The coal content varies from 5 to 20 % in weight by varying the size of coal particles ranging from 0.25mm to 1.60mm.
Initially, each natural moisture content of a raw material has been determined at the temperature of 105°C in a laboratory oven. The Influence of low-coal content on absorption, the apparent density, the contraction and the resistance during compression have been evaluated. The experimental results showed that the optimized composition could be obtained by adding 10% by weight of coal leading thus to insulating ceramic products with water absorption, a density and resistance to compression of 9.40 %, 1.88 g/cm3, 35.46 MPa, respectively. The results show that coal, when mixed with traditional raw materials, offers the conditions to be used as an additive in the production of lightweight ceramic products.
Abstract: In the Fe-3%Si sheets, grade Hi-B, with AlN and MnS
as inhibitors, the Goss grains which abnormally grow do not have a
size greater than the average size of the primary matrix. In this
heterogeneous microstructure, the size factor is not a required
condition for the secondary recrystallization. The onset of the small
Goss grain abnormal growth appears to be related to a particular
behavior of their grain boundaries, to the local texture and to the
distribution of the inhibitors. The presence and the evolution of
oriented clusters ensure to the small Goss grains a favorable
neighborhood to grow. The modified Monte-Carlo approach, which
is applied, considers the local environment of each grain. The grain
growth is dependent of its real spatial position; the matrix
heterogeneity is then taken into account. The grain growth conditions
are considered in the global matrix and in different matrixes
corresponding to A component clusters. The grain growth behaviour
is considered with introduction of energy only, energy and mobility,
energy and mobility and precipitates.
Abstract: Among various testing methodologies, Built-in Self-
Test (BIST) is recognized as a low cost, effective paradigm. Also,
full adders are one of the basic building blocks of most arithmetic
circuits in all processing units. In this paper, an optimized testable 2-
bit full adder as a test building block is proposed. Then, a BIST
procedure is introduced to scale up the building block and to generate
a self testable n-bit full adders. The target design can achieve 100%
fault coverage using insignificant amount of hardware redundancy.
Moreover, Overall test time is reduced by utilizing polymorphic
gates and also by testing full adder building blocks in parallel.
Abstract: In this paper, we define distance partition of vertex set of a graph G with reference to a vertex in it and with the help of the same, a graph with metric dimension two (i.e. β (G) = 2 ) is characterized. In the process, we develop a polynomial time algorithm that verifies if the metric dimension of a given graph G is two. The same algorithm explores all metric bases of graph G whenever β (G) = 2 . We also find a bound for cardinality of any distance partite set with reference to a given vertex, when ever β (G) = 2 . Also, in a graph G with β (G) = 2 , a bound for cardinality of any distance partite set as well as a bound for number of vertices in any sub graph H of G is obtained in terms of diam H .
Abstract: The absolute Cu atoms density in Cu(2S1/22P1/2)
ground state has been measured by Resonance Optical Absorption
(ROA) technique in a DC magnetron sputtering deposition with
argon. We measured these densities under variety of operation
conditions: pressure from 0.6 μbar to 14 μbar, input power from
10W to 200W and N2 mixture from 0% to 100%. For measuring the
gas temperature, we used the simulation of N2 rotational spectra
with a special computer code. The absolute number density of Cu
atoms decreases with increasing the N2 percentage of buffer gas at
any conditions of this work. But the deposition rate, is not decreased
with the same manner. The deposition rate variation is very small
and in the limit of quartz balance measuring equipment accuracy. So
we conclude that decrease in the absolute number density of Cu
atoms in magnetron plasma has not a big effect on deposition rate,
because the diffusion of Cu atoms to the chamber volume and
deviation of Cu atoms from direct path (towards the substrate)
decreases with increasing of N2 percentage of buffer gas. This is
because of the lower mass of N2 atoms compared to the argon ones.
Abstract: Many commercial processes are available for the
removal of H2S from gaseous streams. The desulfurization of gas
streams using aqueous ferric sulfate solution as washing liquor is
studied. Apart from sulfur, only H2O is generated in the process, and
consequently, no waste treatment facilities are required. A distinct
advantage of the process is that the reaction of H2S with is so rapid
and complete that there remains no danger of discharging toxic waste
gas. In this study, the reactive absorption of hydrogen sulfide into
aqueous ferric sulfate solution has been studied and design
calculations for equipments have been done and effective operation
parameters on this process considered. Results show that high
temperature and low pressure are suitable for absorption reaction.
Variation of hydrogen sulfide concentration and Fe3+ concentration
with time in absorption reaction shown that the reaction of ferric
sulfate and hydrogen sulfide is first order with respect to the both
reactant. At low Fe2(SO4)3 concentration the absorption rate of H2S
increase with increasing the Fe2(SO4)3 concentration. At higher
concentration a decrease in the absorption rate was found. At higher
concentration of Fe2(SO4)3, the ionic strength and viscosity of
solution increase remarkably resulting in a decrease of solubility,
diffusivity and hence absorption rate.
Abstract: α-Pinene is the main component of the most
turpentine oils. The hydration of α-pinene with acid catalysts leads to
a complex mixture of monoterpenes. In order to obtain more valuable
products, the α-pinene in the turpentine can be hydrated in dilute
mineral acid solutions to produce α-terpineol. The design of
separation processes requires information on phase equilibrium and
related thermodynamic properties. This paper reports the results of
study on liquid-liquid equilibrium (LLE) of system containing α-
pinene + water and α-terpineol + water.
Binary LLE for α-pinene + water system, and α-terpineol + water
systems were determined by experiment at 301K and atmospheric
pressure. The two component mixture was stirred for about 30min,
then the mixture was left for about 2h for complete phase separation.
The composition of both phases was analyzed by using a Gas
Chromatograph. The experimental data were correlated by
considering both NRTL and UNIQUAC activity coefficient models.
The LLE data for the system of α-pinene + water and α-terpineol +
water were correlated successfully by the NRTL model. The
experimental data were not satisfactorily fitted by the UNIQUAC
model. The NRTL model (α =0.3) correlates the LLE data for the
system of α-pinene + water at 301K with RMSD of 0.0404%. And
the NRTL model (α =0.61) at 301K with RMSD of 0.0058 %. The
NRTL model (α =0.3) correlates the LLE data for the system of α-
terpineol + water at 301K with RMSD of 0.1487% and the NRTL
model (α =0.6) at 301K with RMSD of 0.0032%, between the
experimental and calculated mole fractions.
Abstract: This study mainly aims at assessing the level of
microbial pollution of the water used in the chair system in dental
clinics. For this purpose 36 samples have been randomly collected
from a number of dental surgeries in the city of Tripoli in Libya.
However, 32 of the samples have tested positive to microbial
pollution including 13 of the samples, which have tested positives to
Pseudomonas aeruginosa. Based on the results of the test a further
investigation of the biofilms incorporated within the dental chair
system has been conducted. The laboratory tests of biofilms with
similar design to those found in dental chairs have proved that
bacterial pollution takes place through saliva of the patients who use
the chairs, and that this saliva is rich with nutrients which provides a
suitable breeding ground for all types of bacteria.
Abstract: System MEMORI automatically detects and recognizes
rotated and/or rescaled versions of the objects of a database within
digital color images with cluttered background. This task is accomplished
by means of a region grouping algorithm guided by heuristic
rules, whose parameters concern some geometrical properties and the
recognition score of the database objects. This paper focuses on the
strategies implemented in MEMORI for the estimation of the heuristic
rule parameters. This estimation, being automatic, makes the system
a self configuring and highly user-friendly tool.
Abstract: The Indian subcontinent is facing a massive challenge with regards to the energy security in member countries, i.e. providing a reliable source of electricity to facilitate development across various sectors of the economy and thereby achieve the developmental targets it has set for itself. A highly precarious situation exists in the subcontinent which is observed in the series of system failures which most of the times leads to system collapses-blackouts. To mitigate the issues related with energy security as well as keep in check the increasing supply demand gap, a possible solution that stands in front of the subcontinent is the deployment of an interconnected electricity ‘Supergrid’ designed to carry huge quanta of power across the sub continent as well as provide the infra structure for RES integration. This paper assesses the need and conditions for a Supergrid deployment and consequently proposes a meshed topology based on VSC HVDC converters for the Supergrid modeling.
Abstract: Massive use of places with strong tourist attraction
with the consequent possibility of losing place-identity produces
harmful effects on cities and their users. In order to mitigate this risk,
areas close to such places can be identified so as to widen the
visitor-s range of action and offer alternative activities integrated
with the main site. The cultural places and appropriate activities can
be identified using a method of analysis and design able to trace the
identity of the places, their characteristics and potential, and to
provide a sustainable improvement. The aim of this work is to
propose PlaceMaker as a method of urban analysis and design which
both detects elements that do not feature in traditional mapping and
which constitute the contemporary identity of the places, and
identifies appropriate project interventions. Two final complex maps
– the first of analysis and the second of design – respectively
represent the identity of places and project interventions. In order to
illustrate the method-s potential; the results of the experimentation
carried out in the Trevi-Pantheon route in Rome and the appropriate
interventions to decongest the area are illustrated.
Abstract: According to the new developments in the field of information and communication technologies, the necessity arises for active use of these new technologies in education. It is clear that the integration of technology in education system will be different for primary-higher education or traditional- distance education. In this study, the subject of the integration of technology for distance education was discussed. The subject was taken from the viewpoint of students. With using the information of student feedback about education program in which new technological medias are used, how can survey variables can be separated into the factors as positive, negative and supporter and how can be redesigned education strategy of the higher education associations with the examining the variables of each determinated factor is explained. The paper concludes with the recommendations about the necessitity of working as a group of different area experts and using of numerical methods in establishing of education strategy to be successful.