Abstract: In this paper, the performance of three types of serial
concatenated convolutional codes (SCCC) is compared and analyzed
in additive white Gaussian noise (AWGN) channel. In Type I, only the
parity bits of outer encoder are passed to inner encoder. In Type II and
Type III, both the information bits and the parity bits of outer encoder
are transferred to inner encoder. As results of simulation, Type I shows
the best bit error rate (BER) performance at low signal-to-noise ratio
(SNR). On the other hand, Type III shows the best BER performance
at high SNR in AWGN channel. The simulation results are analyzed
using the distance spectrum.
Abstract: The performance of a sucrose-based H2 production in
a completely stirred tank reactor (CSTR) was modeled by neural
network back-propagation (BP) algorithm. The H2 production was
monitored over a period of 450 days at 35±1 ºC. The proposed model
predicts H2 production rates based on hydraulic retention time
(HRT), recycle ratio, sucrose concentration and degradation, biomass
concentrations, pH, alkalinity, oxidation-reduction potential (ORP),
acids and alcohols concentrations. Artificial neural networks (ANNs)
have an ability to capture non-linear information very efficiently. In
this study, a predictive controller was proposed for management and
operation of large scale H2-fermenting systems. The relevant control
strategies can be activated by this method. BP based ANNs modeling
results was very successful and an excellent match was obtained
between the measured and the predicted rates. The efficient H2
production and system control can be provided by predictive control
method combined with the robust BP based ANN modeling tool.
Abstract: The scientific community has invested a great deal of effort in the fields of discrete wavelet transform in the last few decades. Discrete wavelet transform (DWT) associated with the vector quantization has been proved to be a very useful tool for the compression of image. However, the DWT is very computationally intensive process requiring innovative and computationally efficient method to obtain the image compression. The concurrent transformation of the image can be an important solution to this problem. This paper proposes a model of concurrent DWT for image compression. Additionally, the formal verification of the model has also been performed. Here the Symbolic Model Verifier (SMV) has been used as the formal verification tool. The system has been modeled in SMV and some properties have been verified formally.
Abstract: In this paper a fast motion estimation method for
H.264/AVC named Triplet Search Motion Estimation (TS-ME) is
proposed. Similar to some of the traditional fast motion estimation
methods and their improved proposals which restrict the search points
only to some selected candidates to decrease the computation
complexity, proposed algorithm separate the motion search process to
several steps but with some new features. First, proposed algorithm try
to search the real motion area using proposed triplet patterns instead of
some selected search points to avoid dropping into the local minimum.
Then, in the localized motion area a novel 3-step motion search
algorithm is performed. Proposed search patterns are categorized into
three rings on the basis of the distance from the search center. These
three rings are adaptively selected by referencing the surrounding
motion vectors to early terminate the motion search process. On the
other hand, computation reduction for sub pixel motion search is also
discussed considering the appearance probability of the sub pixel
motion vector. From the simulation results, motion estimation speed
improved by a factor of up to 38 when using proposed algorithm than
that of the reference software of H.264/AVC with ignorable picture
quality loss.
Abstract: Double-diffusive natural convection in an open top
square cavity and heated from the side is studied numerically.
Constant temperatures and concentration are imposed along the right
and left walls while the heat balance at the surface is assumed to obey
Newton-s law of cooling. The finite difference method is used to
solve the dimensionless governing equations. The numerical results
are reported for the effect of Marangoni number, Biot number and
Prandtl number on the contours of streamlines, temperature and
concentration. The predicted results for the average Nusselt number
and Sherwood number are presented for various parametric
conditions. The parameters involved are as follows; the thermal
Marangoni number, 0 ≤ MaT ≤1000 , the solutal Marangoni number,
0 1000 c ≤ Ma ≤ , the Biot number, 0 ≤ Bi ≤ 6 , Grashof number,
5 Gr = 10 and aspect ratio 1. The study focused on both flows; thermal
dominated, N = 0.8 , and compositional dominated, N = 1.3 .
Abstract: Prior research has not effectively investigated how the
profitability of Chinese branches affect FDIs in China [1, 2], so this
study for the first time incorporates realistic earnings information
to systematically investigate effects of innovation, imitation, and
profit factors of FDI diffusions from Taiwan to China. Our nonlinear
least square (NLS) model, which incorporates earnings factors,
forms a nonlinear ordinary differential equation (ODE) in numerical
simulation programs. The model parameters are obtained through
a genetic algorithms (GA) technique and then optimized with the
collected data for the best accuracy. Particularly, Taiwanese regulatory
FDI restrictions are also considered in our modified model to meet
the realistic conditions. To validate the model-s effectiveness, this
investigation compares the prediction accuracy of modified model
with the conventional diffusion model, which does not take account
of the profitability factors.
The results clearly demonstrate the internal influence to be positive,
as early FDI adopters- consistent praises of FDI attract potential firms
to make the same move. The former erects a behavior model for the
latter to imitate their foreign investment decision. Particularly, the
results of modified diffusion models show that the earnings from
Chinese branches are positively related to the internal influence. In
general, the imitating tendency of potential consumers is substantially
hindered by the losses in the Chinese branches, and these firms would
invest less into China. The FDI inflow extension depends on earnings
of Chinese branches, and companies will adjust their FDI strategies
based on the returns. Since this research has proved that earning is
an influential factor on FDI dynamics, our revised model explicitly
performs superior in prediction ability than conventional diffusion
model.
Abstract: The aerodynamics characteristics of a blended-wing body (BWB) aircraft were obtained in Universiti Teknologi MARA low speed wind tunnel. The scaled-down of BWB model consisted of a canard as its horizontal stabilizer. There were four canards with different aspect ratio used in the experiments. Canard setting angles were varied from -20q to 20q. All tests were conducted at velocity of 35 m/s, with Mach number 0.1. At low angles of attacks, the increment of lift slope for various canards aspect ratio is small and almost constant. Higher canard aspect ratio will cause higher drag. However, canard has a high effect to the moment at zero lift, CM,0.The visualization using mini tuff was performed to observe the airflow at the upper surface of canard. KeywordsAerodynamics,blended-wing body, canard, wind tunnel.
Abstract: Carbon nanotubes (CNTs) possess unique structural,
mechanical, thermal and electronic properties, and have been
proposed to be used for applications in many fields. However, to
reach the full potential of the CNTs, many problems still need to be
solved, including the development of an easy and effective
purification procedure, since synthesized CNTs contain impurities,
such as amorphous carbon, carbon nanoparticles and metal particles.
Different purification methods yield different CNT characteristics
and may be suitable for the production of different types of CNTs. In
this study, the effect of different purification chemicals on carbon
nanotube quality was investigated. CNTs were firstly synthesized by
chemical vapor deposition (CVD) of acetylene (C2H2) on a
magnesium oxide (MgO) powder impregnated with an iron nitrate
(Fe(NO3)3·9H2O) solution. The synthesis parameters were selected
as: the synthesis temperature of 800°C, the iron content in the
precursor of 5% and the synthesis time of 30 min. The liquid phase
oxidation method was applied for the purification of the synthesized
CNT materials. Three different acid chemicals (HNO3, H2SO4, and
HCl) were used in the removal of the metal catalysts from the
synthesized CNT material to investigate the possible effects of each
acid solution to the purification step. Purification experiments were
carried out at two different temperatures (75 and 120 °C), two
different acid concentrations (3 and 6 M) and for three different time
intervals (6, 8 and 15 h). A 30% H2O2 : 3M HCl (1:1 v%) solution
was also used in the purification step to remove both the metal
catalysts and the amorphous carbon. The purifications using this
solution were performed at the temperature of 75°C for 8 hours.
Purification efficiencies at different conditions were evaluated by
thermogravimetric analysis. Thermal and electrical properties of
CNTs were also determined. It was found that the obtained electrical
conductivity values for the carbon nanotubes were typical for organic
semiconductor materials and thermal stabilities were changed
depending on the purification chemicals.
Abstract: Design and evaluation of reciprocating compressors
should include a pulsation study. The object is to ensure that
predicted pulsation levels meet guidelines to limit vibration, shaking
forces, noise, associated pressure drops, horsepower losses and
fabrication cost and time to acceptable levels. This paper explains
procedures and recommendations to select and size pulsation
suppression devices to obtain optimum arrangement in terms of
pulsation, vibration, shaking forces, performance, reliability, safety,
operation, maintenance and commercial conditions. Model and
advanced formulations for pulsation study are presented. The effect
of the full fluid dynamic model on the prediction of pulsation waves
and resulting frequency spectrum distributions are discussed.
Advanced and optimum methods of controlling pulsations are
highlighted. Useful recommendations and guidelines for pulsation
control, piping pulsation analysis, pulsation vessel design, shaking
forces, low pressure drop orifices, pulsation study report and devices
to mitigate pulsation and shaking problems are discussed.
Abstract: Double-diffusive steady convection in a partially
porous cavity with partially permeable walls and under the combined
buoyancy effects of thermal and mass diffusion was analysed
numerically using finite volume method.
The top wall is well insulated and impermeable while the bottom
surface is partially well insulated and impermeable and partially
submitted to constant temperature T1 and concentration C1. Constant
equal temperature T2 and concentration C2 are imposed along the
vertical surfaces of the enclosure. Mass suction/injection and
injection/suction are respectively considered at the bottom of the
porous centred partition and at one of the vertical walls.
Heat and mass transfer characteristics as streamlines and average
Nusselt numbers and Sherwood numbers were discussed for different
values of buoyancy ratio, Rayleigh number, and injection/suction
coefficient.
It is especially noted that increasing the injection factor
disadvantages the exchanges in the case of the injection while the
transfer is augmented in case of suction. On the other hand, a critical
value of the buoyancy ratio was highlighted for which heat and mass
transfers are minimized.
Abstract: In this paper, parallel interface for microprocessor
trainer was implemented. A programmable parallel–port device such
as the IC 8255A is initialized for simple input or output and for
handshake input or output by choosing kinds of modes. The hardware
connections and the programs can be used to interface
microprocessor trainer and a personal computer by using IC 8255A.
The assembly programs edited on PC-s editor can be downloaded to
the trainer.
Abstract: A laboratory set-up was designed to survey the
effectiveness of UV/O3 advanced oxidation process (AOP) for the
removal of Carbaryl from polluted water in batch reactor. The study
was carried out by UV/O3 process for water samples containing 1 to
20 mg/L of Carbaryl in distilled water. Also the range of drinking
water resources adjusted in synthetic water and effects of contact
time, pH and Carbaryl concentration were studied. The residual
pesticide concentration was determined by applying high
performance liquid chromatography (HPLC). The results indicated
that increasing of retention time and pH, enhances pesticide removal
efficiency. The removal efficiency has been affected by pesticide
initial concentration. Samples with low pesticide concentration
showed a remarkable removal efficiency compared to the samples
with high pesticide concentration. AOP method showed the removal
efficiencies of 80% to 100%. Although process showed high
performance for removal of pesticide from water samples, this
process has different disadvantages including complication,
intolerability, difficulty of maintenance and equipmental and
structural requirements.
Abstract: Column leach test has been performed to examine the
behavior of leaching of sodium, calcium and potassium in landfills.
In the column leach apparatus, two different layers of contaminated
and uncontaminated soils of different height ratios (ratio of depth of
contaminated soil to the depth of uncontaminated soil) are taken.
Water is poured from an overhead tank at a particular flowrate to the
inlet of the soil column for a certain ponding depth over the
contaminated soil. Subsequent infiltration causes leaching and the
leachates are collected from the bottom of the column. The
concentrations of Na, Ca and K in the leachate are measured using
flame photometry. The experiments are further extended by changing
the rates of flow from the overhead tank to the inlet of the column in
achieving the same ponding depth. The experiments are performed
for different scenarios in which the height ratios are altered and the
variations of concentrations of Na, Ca, and K are observed. The study
brings an estimation of leaching in landfill sites for different heights
and precipitation intensity where a ponding depth is maintained over
the landfill. It has been observed that the leaching behavior of Na,
Ca, and K are not similar. Calcium exhibits highest amount of
leaching compared to Sodium and Potassium under similar
experimental conditions.
Abstract: In recent five decades, textured yarns of polyester fiber produced by false twist method are the most
important and mass-produced manmade fibers. There are
many parameters of cross section which affect the physical and mechanical properties of textured yarns. These parameters
are surface area, perimeter, equivalent diameter, large
diameter, small diameter, convexity, stiffness, eccentricity, and hydraulic diameter. These parameters were evaluated by
digital image processing techniques. To find trends between production criteria and evaluated parameters of cross section, three criteria of production line have been adjusted and different types of yarns were produced. These criteria are
temperature, drafting ratio, and D/Y ratio. Finally the relations between production criteria and cross section parameters were
considered. The results showed that the presented technique can recognize and measure the parameters of fiber cross section in acceptable accuracy. Also, the optimum condition
of adjustments has been estimated from results of image analysis evaluation.
Abstract: This paper deals with the application for contentbased
image retrieval to extract color feature from natural images
stored in the image database by segmenting the image through
clustering. We employ a class of nonparametric techniques in which
the data points are regarded as samples from an unknown probability
density. Explicit computation of the density is avoided by using the
mean shift procedure, a robust clustering technique, which does not
require prior knowledge of the number of clusters, and does not
constrain the shape of the clusters. A non-parametric technique for
the recovery of significant image features is presented and
segmentation module is developed using the mean shift algorithm to
segment each image. In these algorithms, the only user set parameter
is the resolution of the analysis and either gray level or color images
are accepted as inputs. Extensive experimental results illustrate
excellent performance.
Abstract: This paper present a circular patch microstrip array antenna operate in KU-band (10.9GHz – 17.25GHz). The proposed circular patch array antenna will be in light weight, flexible, slim and compact unit compare with current antenna used in KU-band. The paper also presents the detail steps of designing the circular patch microstrip array antenna. An Advance Design System (ADS) software is used to compute the gain, power, radiation pattern, and S11 of the antenna. The proposed Circular patch microstrip array antenna basically is a phased array consisting of 'n' elements (circular patch antennas) arranged in a rectangular grid. The size of each element is determined by the operating frequency. The incident wave from satellite arrives at the plane of the antenna with equal phase across the surface of the array. Each 'n' element receives a small amount of power in phase with the others. There are feed network connects each element to the microstrip lines with an equal length, thus the signals reaching the circular patches are all combined in phase and the voltages add up. The significant difference of the circular patch array antenna is not come in the phase across the surface but in the magnitude distribution.
Abstract: In this paper, we propose the pre-processor based on
the Evidence Supporting Measure of Similarity (ESMS) filter and also
propose the unified fusion approach (UFA) based on the general
fusion machine coupled with ESMS filter, which improve the
correctness and precision of information fusion in any fields of
application. Here we mainly apply the new approach to Simultaneous
Localization And Mapping (SLAM) of Pioneer II mobile robots. A
simulation experiment was performed, where an autonomous virtual
mobile robot with sonar sensors evolves in a virtual world map with
obstacles. By comparing the result of building map according to the
general fusion machine (here DSmT-based fusing machine and
PCR5-based conflict redistributor considereded) coupling with ESMS
filter and without ESMS filter, it shows the benefit of the selection of
the sources as a prerequisite for improvement of the information
fusion, and also testifies the superiority of the UFA in dealing with
SLAM.
Abstract: In this study it is aimed to determine the level of preservice teachers- computer phobia. Whether or not computer phobia meaningfully varies statistically according to gender and computer experience has been tested in the study. The study was performed on 430 pre-service teachers at the Education Faculty in Rize/Turkey. Data in the study were collected through the Computer Phobia Scale consisting of the “Personal Knowledge Questionnaire", “Computer Anxiety Rating Scale", and “Computer Thought Survey". In this study, data were analyzed with statistical processes such as t test, and correlation analysis. According to results of statistical analyses, computer phobia of male pre-service teachers does not statistically vary depending on their gender. Although male preservice teachers have higher computer anxiety scores, they have lower computer thought scores. It was also observed that there is a negative and intensive relation between computer experience and computer anxiety. Meanwhile it was found out that pre-service teachers using computer regularly indicated lower computer anxiety. Obtained results were tried to be discussed in terms of the number of computer classes in the Education Faculty curriculum, hours of computer class and the computer availability of student teachers.
Abstract: This article proposes a novel Pareto-based multiobjective
meta-heuristic algorithm named non-dominated ranking
genetic algorithm (NRGA) to solve multi-facility location-allocation
problem. In NRGA, a fitness value representing rank is assigned to
each individual of the population. Moreover, two features ranked
based roulette wheel selection including select the fronts and choose
solutions from the fronts, are utilized. The proposed solving
methodology is validated using several examples taken from the
specialized literature. The performance of our approach shows that
NRGA algorithm is able to generate true and well distributed Pareto
optimal solutions.
Abstract: In this paper we use data mining techniques to investigate factors that contribute significantly to enhancing the risk of acute coronary syndrome. We assume that the dependent variable is diagnosis – with dichotomous values showing presence or absence of disease. We have applied binary regression to the factors affecting the dependent variable. The data set has been taken from two different cardiac hospitals of Karachi, Pakistan. We have total sixteen variables out of which one is assumed dependent and other 15 are independent variables. For better performance of the regression model in predicting acute coronary syndrome, data reduction techniques like principle component analysis is applied. Based on results of data reduction, we have considered only 14 out of sixteen factors.