Abstract: According to the governmental data, the cases of oral
cancers doubled in the past 10 years. This had brought heavy burden to
the patients- family, the society, and the country. The literature
generally evidenced the betel nut contained particular chemicals that
can cause oral cancers. Research in Taiwan had also proofed that 90
percent of oral cancer patients had experience of betel nut chewing. It
is thus important to educate the betel-nut hobbyists to cease such a
hazardous behavior. A program was then organized to establish
several training classes across different areas specific to help ceasing
this particular habit. Purpose of this research was to explore the
attitude and intention toward ceasing betel-nut chewing before and
after attending the training classes. 50 samples were taken from a
ceasing class with average age at 45 years old with high school
education (54%). 74% of the respondents were male in service or
agricultural industries. Experiences in betel-nut chewing were 5-20
years with a dose of 1-20 pieces per day. The data had shown that 60%
of the respondents had cigarette smoking habit, and 30% of the
respondents were concurrently alcoholic dependent. Research results
indicated that the attitude, intentions, and the knowledge on oral
cancers were found significant different between before and after
attendance. This provided evidence for the effectiveness of the training
class. However, we do not perform follow-up after the class.
Noteworthy is the test result also shown that participants who were
drivers as occupation, or habitual smokers or alcoholic dependents
would be less willing to quit the betel-nut chewing. The test results
indicated as well that the educational levels and the type of occupation
may have significant impacts on an individual-s decisions in taking
betel-nut or substance abuse.
Abstract: Power transformer consists of components which are
under consistent thermal and electrical stresses. The major
component which degrades under these stresses is the paper
insulation of the power transformer. At site, lightning impulses and
cable faults may cause the winding deformation. In addition, the
winding may deform due to impact during transportation. A
deformed winding will excite more stress to its insulating paper thus
will degrade it. Insulation degradation will shorten the life-span of
the transformer. Currently there are two methods of detecting the
winding deformation which are Sweep Frequency Response
Analysis (SFRA) and Low Voltage Impulse Test (LVI). The latter
injects current pulses to the winding and capture the admittance
plot. In this paper, a transformer which experienced overheating and
arcing was identified, and both SFRA and LVI were performed.
Next, the transformer was brought to the factory for untanking. The
untanking results revealed that the LVI is more accurate than the
SFRA method for this case study.
Abstract: This paper presents the study of hardness profile of spur gear heated by induction heating process in function of the machine parameters, such as the power (kW), the heating time (s) and the generator frequency (kHz). The global work is realized by 3D finite-element simulation applied to the process by coupling and resolving the electromagnetic field and the heat transfer problems, and it was performed in three distinguished steps. First, a Comsol 3D model was built using an adequate formulation and taking into account the material properties and the machine parameters. Second, the convergence study was conducted to optimize the mesh. Then, the surface temperatures and the case depths were deeply analyzed in function of the initial current density and the heating time in medium frequency (MF) and high frequency (HF) heating modes and the edge effect were studied. Finally, the simulations results are validated using experimental tests.
Abstract: One of the processes of slope that occurs every year in Iran and some parts of world and cause a lot of criminal and financial harms is called landslide. They are plenty of method to stability landslide in soil and rock slides. The use of the best method with the least cost and in the shortest time is important for researchers. In this research, determining the best method of stability is investigated by using of Decision Support systems. DSS is made for this purpose and was used (for Hasan Salaran area in Kurdistan). Field study data from topography, slope, geology, geometry of landslide and the related features was used. The related data entered decision making managements programs (DSS) (ALES).Analysis of mass stability indicated the instability potential at present. Research results show that surface and sub surface drainage the best method of stabilizing. Analysis of stability shows that acceptable increase in security coefficient is a consequence of drainage.
Abstract: The objective of this research is to develop the
performance indicators (PIs) in operational level for the Pre-hospital Emergency Medical Service (EMS) system employing in Thailand. This research started with ascertaining the current pre-hospital care
system. The team analyzed the strategies of Narerthorn, a government unit under the ministry of public health, and the existing PIs of the pre-hospital care. Afterwards, the current National Strategic Plan of EMS development (2008-2012) of the Emergency
Medical Institute of Thailand (EMIT) was considered using strategic
analysis to developed Strategy Map (SM) and identified the Success
Factors (SFs). The analysis results from strategy map and SFs were used to develop the Performance Indicators (PIs). To verify the set of
PIs, the team has interviewed with the relevant practitioners for the possibilities to implement the PIs. To this paper, it was to ascertain
that all the developed PIs support the objectives of the strategic plan. Nevertheless, the results showed that the operational level PIs suited
only with the first dimension of National Strategic Plan
(infrastructure and information technology development). Besides,
the SF was the infrastructure development (to contribute the EMS system to people throughout with standard and efficiency both in normally and disaster conditions). Finally, twenty-nine indicators
were developed from the analysis results of SM and SFs.
Abstract: This is an application research presenting the
improvement of production quality using the six sigma solutions and
the analyses of benefit-cost ratio. The case of interest is the
production of tile-concrete. Such production has faced with the
problem of high nonconforming products from an inappropriate
surface coating and had low process capability based on the strength
property of tile. Surface coating and tile strength are the most critical
to quality of this product. The improvements followed five stages of
six sigma solutions. After the improvement, the production yield was
improved to 80% as target required and the defective products from
coating process was remarkably reduced from 29.40% to 4.09%. The
process capability based on the strength quality was increased from
0.87 to 1.08 as customer oriented. The improvement was able to save
the materials loss for 3.24 millions baht or 0.11 million dollars. The
benefits from the improvement were analyzed from (1) the reduction
of the numbers of non conforming tile using its factory price for
surface coating improvement and (2) the materials saved from the
increment of process capability. The benefit-cost ratio of overall
improvement was high as 7.03. It was non valuable investment in
define, measure, analyses and the initial of improve stages after that
it kept increasing. This was due to there were no benefits in define,
measure, and analyze stages of six sigma since these three stages
mainly determine the cause of problem and its effects rather than
improve the process. The benefit-cost ratio starts existing in the
improve stage and go on. Within each stage, the individual benefitcost
ratio was much higher than the accumulative one as there was an
accumulation of cost since the first stage of six sigma. The
consideration of the benefit-cost ratio during the improvement
project helps make decisions for cost saving of similar activities
during the improvement and for new project. In conclusion, the
determination of benefit-cost ratio behavior through out six sigma
implementation period provides the useful data for managing quality
improvement for the optimal effectiveness. This is the additional
outcome from the regular proceeding of six sigma.
Abstract: Above Elbow Prosthesis is one of the most commonly
amputated or missing limbs. The research is done for modelling
techniques of upper limb prosthesis and design of high torque, light
weight and compact in size elbow actuator. The purposed actuator
consists of a DC motor, planetary gear set and a harmonic drive. The
calculations show that the actuator is good enough to be used in real
life powered prosthetic upper limb or rehabilitation exoskeleton.
Abstract: The objective of this paper is to study the electrical
resistivity complexity between field and laboratory measurement, in
order to improve the effectiveness of data interpretation for
geophysical ground resistivity survey. The geological outcrop in
Penang, Malaysia with an obvious layering contact was chosen as the
study site. Two dimensional geoelectrical resistivity imaging were
used in this study to maps the resistivity distribution of subsurface,
whereas few subsurface sample were obtained for laboratory
advance. In this study, resistivity of samples in original conditions is
measured in laboratory by using time domain low-voltage technique,
particularly for granite core sample and soil resistivity measuring set
for soil sample. The experimentation results from both schemes are
studied, analyzed, calibrated and verified, including basis and
correlation, degree of tolerance and characteristics of substance.
Consequently, the significant different between both schemes is
explained comprehensively within this paper.
Abstract: In this paper, transversal vibration of buried pipelines
during loading induced by underground explosions is analyzed. The
pipeline is modeled as an infinite beam on an elastic foundation, so
that soil-structure interaction is considered by means of transverse
linear springs along the pipeline. The pipeline behavior is assumed to
be ideal elasto-plastic which an ultimate strain value limits the plastic
behavior. The blast loading is considered as a point load, considering
the affected length at some point of the pipeline, in which the
magnitude decreases exponentially with time. A closed-form solution
for the quasi-static problem is carried out for both elastic and elasticperfect
plastic behaviors of pipe materials. At the end, a comparative
study on steel and polyethylene pipes with different sizes buried in
various soil conditions, affected by a predefined underground
explosion is conducted, in which effect of each parameter is
discussed.
Abstract: The aluminum bronze matrix alumina composites using hot press and resin infiltration were investigated to study their porosities, hardness, bending strengths, and microstructures. The experiment results show that the hardness of the sintered composites with the decrease of porosity increases. The composites without and with resin infiltration have about HRF 42-61 of about 34-40% of porosity and about HRF 62-83 of about 30-36% of porosity, respectively. Besides, the alumina composites contain a more amount of iron and nickel powders would cause a lower bending strength due to forming some weaker bonding among the iron, nickel, copper, aluminum under this hot pressing of shorter time.
Abstract: This study performs a comparative analysis of the 21 Greek Universities in terms of their public funding, awarded for covering their operating expenditure. First it introduces a DEA/MCDM model that allocates the fund into four expenditure factors in the most favorable way for each university. Then, it presents a common, consensual assessment model to reallocate the amounts, remaining in the same level of total public budget. From the analysis it derives that a number of universities cannot justify the public funding in terms of their size and operational workload. For them, the sufficient reduction of their public funding amount is estimated as a future target. Due to the lack of precise data for a number of expenditure criteria, the analysis is based on a mixed crisp-ordinal data set.
Abstract: Text categorization is the problem of classifying text
documents into a set of predefined classes. In this paper, we
investigated three approaches to build a meta-classifier in order to
increase the classification accuracy. The basic idea is to learn a metaclassifier
to optimally select the best component classifier for each
data point. The experimental results show that combining classifiers
can significantly improve the accuracy of classification and that our
meta-classification strategy gives better results than each individual
classifier. For 7083 Reuters text documents we obtained a
classification accuracies up to 92.04%.
Abstract: The issue of unintentional islanding in PV grid
interconnection still remains as a challenge in grid-connected
photovoltaic (PV) systems. This paper discusses the overview of
popularly used anti-islanding detection methods, practically applied
in PV grid-connected systems. Anti-islanding methods generally can
be classified into four major groups, which include passive methods,
active methods, hybrid methods and communication base methods.
Active methods have been the preferred detection technique over the
years due to very small non-detected zone (NDZ) in small scale
distribution generation. Passive method is comparatively simpler
than active method in terms of circuitry and operations. However, it
suffers from large NDZ that significantly reduces its performance.
Communication base methods inherit the advantages of active and
passive methods with reduced drawbacks. Hybrid method which
evolved from the combination of both active and passive methods
has been proven to achieve accurate anti-islanding detection by many
researchers. For each of the studied anti-islanding methods, the
operation analysis is described while the advantages and
disadvantages are compared and discussed. It is difficult to pinpoint a
generic method for a specific application, because most of the
methods discussed are governed by the nature of application and
system dependent elements. This study concludes that the setup and
operation cost is the vital factor for anti-islanding method selection in
order to achieve minimal compromising between cost and system
quality.
Abstract: This paper proposes a method, combining color and
layout features, for identifying documents captured from lowresolution
handheld devices. On one hand, the document image color
density surface is estimated and represented with an equivalent
ellipse and on the other hand, the document shallow layout structure
is computed and hierarchically represented. The combined color and
layout features are arranged in a symbolic file, which is unique for
each document and is called the document-s visual signature. Our
identification method first uses the color information in the
signatures in order to focus the search space on documents having a
similar color distribution, and finally selects the document having the
most similar layout structure in the remaining search space. Finally,
our experiment considers slide documents, which are often captured
using handheld devices.
Abstract: This paper presents a simplified version of Data Envelopment Analysis (DEA) - a conventional approach to evaluating the performance and ranking of competitive objects characterized by two groups of factors acting in opposite directions: inputs and outputs. DEA with a Perfect Object (DEA PO) augments the group of actual objects with a virtual Perfect Object - the one having greatest outputs and smallest inputs. It allows for obtaining an explicit analytical solution and making a step to an absolute efficiency. This paper develops this approach further and introduces a DEA model with Partially Perfect Objects. DEA PPO consecutively eliminates the smallest relative inputs or greatest relative outputs, and applies DEA PO to the reduced collections of indicators. The partial efficiency scores are combined to get the weighted efficiency score. The computational scheme remains simple, like that of DEA PO, but the advantage of the DEA PPO is taking into account all of the inputs and outputs for each actual object. Firm evaluation is considered as an example.
Abstract: Blood pulse is an important human physiological signal commonly used for the understanding of the individual physical health. Current methods of non-invasive blood pulse sensing require direct contact or access to the human skin. As such, the performances of these devices tend to vary with time and are subjective to human body fluids (e.g. blood, perspiration and skin-oil) and environmental contaminants (e.g. mud, water, etc). This paper proposes a simulation model for the novel method of non-invasive acquisition of blood pulse using the disturbance created by blood flowing through a localized magnetic field. The simulation model geometry represents a blood vessel, a permanent magnet, a magnetic sensor, surrounding tissues and air in 2-dimensional. In this model, the velocity and pressure fields in the blood stream are described based on Navier-Stroke equations and the walls of the blood vessel are assumed to have no-slip condition. The blood assumes a parabolic profile considering a laminar flow for blood in major artery near the skin. And the inlet velocity follows a sinusoidal equation. This will allow the computational software to compute the interactions between the magnetic vector potential generated by the permanent magnet and the magnetic nanoparticles in the blood. These interactions are simulated based on Maxwell equations at the location where the magnetic sensor is placed. The simulated magnetic field at the sensor location is found to assume similar sinusoidal waveform characteristics as the inlet velocity of the blood. The amplitude of the simulated waveforms at the sensor location are compared with physical measurements on human subjects and found to be highly correlated.
Abstract: Sharing the manufacturing facility through remote
operation and monitoring of a machining process is challenge for
effective use the production facility. Several automation tools in term
of hardware and software are necessary for successfully remote
operation of a machine. This paper presents a prototype of workpiece
holding attachment for remote operation of milling process by self
configuration the workpiece setup. The prototype is designed with
mechanism to reorient the work surface into machining spindle
direction with high positioning accuracy. Variety of parts geometry
is hold by attachment to perform single setup machining. Pin type
with array pattern additionally clamps the workpiece surface from
two opposite directions for increasing the machining rigidity.
Optimum pins configuration for conforming the workpiece geometry
with minimum deformation is determined through hybrid algorithms,
Genetic Algorithms (GA) and Particle Swarm Optimization (PSO).
Prototype with intelligent optimization technique enables to hold
several variety of workpiece geometry which is suitable for
machining low of repetitive production in remote operation.
Abstract: Electrospinning is a broadly used technology to obtain
polymeric nanofibers ranging from several micrometers down to
several hundred nanometers for a wide range of applications. It offers
unique capabilities to produce nanofibers with controllable porous
structure. With smaller pores and higher surface area than regular
fibers, electrospun fibers have been successfully applied in various
fields, such as, nanocatalysis, tissue engineering scaffolds, protective
clothing, filtration, biomedical, pharmaceutical, optical electronics,
healthcare, biotechnology, defense and security, and environmental
engineering. In this study, polyurethane nanofibers were obtained
under different electrospinning parameters. Fiber morphology and
diameter distribution were investigated in order to understand them
as a function of process parameters.
Abstract: Statistical learning theory was developed by Vapnik. It
is a learning theory based on Vapnik-Chervonenkis dimension. It also
has been used in learning models as good analytical tools. In general, a
learning theory has had several problems. Some of them are local
optima and over-fitting problems. As well, statistical learning theory
has same problems because the kernel type, kernel parameters, and
regularization constant C are determined subjectively by the art of
researchers. So, we propose an evolutionary statistical learning theory
to settle the problems of original statistical learning theory.
Combining evolutionary computing into statistical learning theory,
our theory is constructed. We verify improved performances of an
evolutionary statistical learning theory using data sets from KDD cup.
Abstract: An optical fiber Fabry-Perot interferometer (FFPI) is
proposed and demonstrated for dynamic measurements in a
mechanical vibrating target. A polishing metal with a low reflectance
value adhered to a mechanical vibrator was excited via a function
generator at various excitation frequencies. Output interference
fringes were generated by modulating the reference and sensing
signal at the output arm. A fringe-counting technique was used for
interpreting the displacement information on the dedicated computer.
The fiber interferometer has been found the capability of the
displacement measurements of 1.28 μm – 96.01 μm. A commercial
displacement sensor was employed as a reference sensor for
investigating the measurement errors from the fiber sensor. A
maximum percentage measurement error of approximately 1.59 %
was obtained.