Abstract: Motion estimation is a key problem in video
processing and computer vision. Optical flow motion estimation can
achieve high estimation accuracy when motion vector is small.
Three-step search algorithm can handle large motion vector but not
very accurate. A joint algorithm was proposed in this paper to
achieve high estimation accuracy disregarding whether the motion
vector is small or large, and keep the computation cost much lower
than full search.
Abstract: Vapour recompression system has been used to
enhance reduction in energy consumption and improvement in
energy effectiveness of distillation columns. However, the effects of
certain parameters have not been taken into consideration. One of
such parameters is the column heat loss which has either been
assumed to be a certain percent of reboiler heat transfer or negligible.
The purpose of this study was to evaluate the heat loss from an
ethanol-water vapour recompression distillation column with
pressure increase across the compressor (VRCAS) and compare the
results obtained and its effect on some parameters in similar system
(VRCCS) where the column heat loss has been assumed or neglected.
Results show that the heat loss evaluated was higher when compared
with that obtained for the column VRCCS. The results also showed
that increase in heat loss could have significant effect on the total
energy consumption, reboiler heat transfer, the number of trays and
energy effectiveness of the column.
Abstract: The excessive consumption of fossil energies (electrical energy) during summer caused by the technological development involves more and more climate warming.
In order to reduce the worst impact of gas emissions produced from classical air conditioning, heat driven solar absorption chiller is pretty promising; it consists on using solar as motive energy which is clean and environmentally friendly to provide cold.
Solar absorption machine is composed by four components using Lithium Bromide /water as a refrigerating couple. LiBr- water is the most promising in chiller applications due to high safety, high volatility ratio, high affinity, high stability and its high latent heat. The lithium bromide solution is constitute by the salt lithium bromide which absorbs water under certain conditions of pressure and temperature however if the concentration of the solution is high in the absorption chillers; which exceed 70%, the solution will crystallize.
The main aim of this article is to study the phenomena of the crystallization and to evaluate how the dependence between the electric conductivity and the concentration which should be controlled.
Abstract: Purpose of this work is to develop an automatic classification system that could be useful for radiologists in the breast cancer investigation. The software has been designed in the framework of the MAGIC-5 collaboration. In an automatic classification system the suspicious regions with high probability to include a lesion are extracted from the image as regions of interest (ROIs). Each ROI is characterized by some features based generally on morphological lesion differences. A study in the space features representation is made and some classifiers are tested to distinguish the pathological regions from the healthy ones. The results provided in terms of sensitivity and specificity will be presented through the ROC (Receiver Operating Characteristic) curves. In particular the best performances are obtained with the Neural Networks in comparison with the K-Nearest Neighbours and the Support Vector Machine: The Radial Basis Function supply the best results with 0.89 ± 0.01 of area under ROC curve but similar results are obtained with the Probabilistic Neural Network and a Multi Layer Perceptron.
Abstract: Traffic density, an indicator of traffic
conditions, is one of the most critical characteristics to
Intelligent Transport Systems (ITS). This paper investigates
recursive traffic density estimation using the information
provided from inductive loop detectors. On the basis of the
phenomenological relationship between speed and density, the
existing studies incorporate a state space model and update the
density estimate using vehicular speed observations via the
extended Kalman filter, where an approximation is made
because of the linearization of the nonlinear observation
equation. In practice, this may lead to substantial estimation
errors. This paper incorporates a suitable transformation to
deal with the nonlinear observation equation so that the
approximation is avoided when using Kalman filter to
estimate the traffic density. A numerical study is conducted. It
is shown that the developed method outperforms the existing
methods for traffic density estimation.
Abstract: The last years have seen an increasing use of image analysis techniques in the field of biomedical imaging, in particular in microscopic imaging. The basic step for most of the image analysis techniques relies on a background image free of objects of interest, whether they are cells or histological samples, to perform further analysis, such as segmentation or mosaicing. Commonly, this image consists of an empty field acquired in advance. However, many times achieving an empty field could not be feasible. Or else, this could be different from the background region of the sample really being studied, because of the interaction with the organic matter. At last, it could be expensive, for instance in case of live cell analyses. We propose a non parametric and general purpose approach where the background is built automatically stemming from a sequence of images containing even objects of interest. The amount of area, in each image, free of objects just affects the overall speed to obtain the background. Experiments with different kinds of microscopic images prove the effectiveness of our approach.
Abstract: This paper describes vibration analysis using the finite
element method for a small earphone, especially for the diaphragm
shape with a low-rigidity. The viscoelastic diaphragm is supported by
multiple nonlinear concentrated springs with linear hysteresis
damping. The restoring forces of the nonlinear springs have cubic
nonlinearity. The finite elements for the nonlinear springs with
hysteresis are expressed and are connected to the diaphragm that is
modeled by linear solid finite elements in consideration of a complex
modulus of elasticity. Further, the discretized equations in physical
coordinates are transformed into the nonlinear ordinary coupled
equations using normal coordinates corresponding to the linear natural
modes. We computed the nonlinear stationary and non-stationary
responses due to the internal resonance between modes with large
amplitude in the nonlinear springs and elastic modes in the diaphragm.
The non-stationary motions are confirmed as the chaos due to the
maximum Lyapunov exponents with a positive number. From the time
histories of the deformation distribution in the chaotic vibration, we
identified nonlinear modal couplings.
Abstract: This paper presented a proposed design for
transcutaneous inductive powering links. The design used to transfer
power and data to the implanted devices such as implanted
Microsystems to stimulate and monitoring the nerves and muscles.
The system operated with low band frequency 13.56 MHZ according
to industrial- scientific – medical (ISM) band to avoid the tissue
heating. For external part, the modulation index is 13 % and the
modulation rate 7.3% with data rate 1 Mbit/s assuming Tbit=1us. The
system has been designed using 0.35-μm fabricated CMOS
technology. The mathematical model is given and the design is
simulated using OrCAD P Spice 16.2 software tool and for real-time
simulation the electronic workbench MULISIM 11 has been used.
The novel circular plane (pancake) coils was simulated using
ANSOFT- HFss software.
Abstract: In this paper we present a technique to speed up
ICA based on the idea of reducing the dimensionality of the data
set preserving the quality of the results. In particular we refer to
FastICA algorithm which uses the Kurtosis as statistical property
to be maximized. By performing a particular Johnson-Lindenstrauss
like projection of the data set, we find the minimum dimensionality
reduction rate ¤ü, defined as the ratio between the size k of the reduced
space and the original one d, which guarantees a narrow confidence
interval of such estimator with high confidence level. The derived
dimensionality reduction rate depends on a system control parameter
β easily computed a priori on the basis of the observations only.
Extensive simulations have been done on different sets of real world
signals. They show that actually the dimensionality reduction is very
high, it preserves the quality of the decomposition and impressively
speeds up FastICA. On the other hand, a set of signals, on which the
estimated reduction rate is greater than 1, exhibits bad decomposition
results if reduced, thus validating the reliability of the parameter β.
We are confident that our method will lead to a better approach to
real time applications.
Abstract: Electro-optical devices are increasingly used for
military sea-, land- and air applications to detect, recognize and track
objects. Typically, these devices produce video information that is
presented to an operator. However, with increasing availability of
electro-optical devices the data volume is becoming very large,
creating a rising need for automated analysis. In a military setting,
this typically involves detecting and recognizing objects at a large
distance, i.e. when they are difficult to distinguish from background
and noise. One may consider combining multiple images from a
video stream into a single enhanced image that provides more
information for the operator. In this paper we investigate a simple
algorithm to enhance simulated images from a military context and
investigate how the enhancement is affected by various types of
disturbance.
Abstract: One of the disadvantages of using OFDM is the larger
peak to averaged power ratio (PAPR) in its time domain signal. The
larger PAPR signal would course the fatal degradation of bit error
rate performance (BER) due to the inter-modulation noise in the nonlinear
channel. This paper proposes an improved DSI (Dummy
Sequence Insertion) method, which can achieve the better PAPR and
BER performances. The feature of proposed method is to optimize
the phase of each dummy sub-carrier so as to reduce the PAPR
performance by changing all predetermined phase coefficients in the
time domain signal, which is calculated for data sub-carriers and
dummy sub-carriers separately. To achieve the better PAPR
performance, this paper also proposes to employ the time-frequency
domain swapping algorithm for fine adjustment of phase coefficient
of the dummy subcarriers, which can achieve the less complexity of
processing and achieves the better PAPR and BER performances
than those for the conventional DSI method. This paper presents
various computer simulation results to verify the effectiveness of
proposed method as comparing with the conventional methods in the
non-linear channel.
Abstract: Mobile Ad hoc Networks is an autonomous system of
mobile nodes connected by multi-hop wireless links without
centralized infrastructure support. As mobile communication gains
popularity, the need for suitable ad hoc routing protocols will
continue to grow. Efficient dynamic routing is an important research
challenge in such a network. Bandwidth constrained mobile devices
use on-demand approach in their routing protocols because of its
effectiveness and efficiency. Many researchers have conducted
numerous simulations for comparing the performance of these
protocols under varying conditions and constraints. Most of them are
not aware of MAC Protocols, which will impact the relative
performance of routing protocols considered in different network
scenarios. In this paper we investigate the choice of MAC protocols
affects the relative performance of ad hoc routing protocols under
different scenarios. We have evaluated the performance of these
protocols using NS2 simulations. Our results show that the
performance of routing protocols of ad hoc networks will suffer when
run over different MAC Layer protocols.
Abstract: Recently, there have been an increasing interest in RFID system and RFID systems have been applied to various applications. Load balancing is a fundamental technique for providing scalability of systems by moving workload from overloaded nodes to under-loaded nodes. This paper presents an approach to adaptive load balancing for RFID middlewares. Workloads of RFID middlewares can have a considerable variation according to the location of the connected RFID readers and can abruptly change at a particular instance. The proposed approach considers those characteristics of RFID middle- wares to provide an efficient load balancing.
Abstract: In this paper a tuning fork type structure of Ultra
Wideband (UWB) antenna is proposed. The antenna offers excellent
performance for UWB system, ranging from 3.7 GHz to 13.8 GHz.
The antenna exhibits a 10 dB return loss bandwidth over the entire
frequency band. The rectangular patch antenna is designed on FR4
substrate and fed with 50 ohms microstrip line by optimizing the
width of partial ground, the width and position of the feedline to
operate in UWB. The rectangular patch is then modified to tuning
fork structure by maintaining UWB frequency range.
Abstract: Green- spaces might be very attractive, but
where are the economic benefits? What value do nature and
landscape have for us? What difference will it make to jobs,
health and the economic strength of areas struggling with
deprivation and social problems? [1].There is a need to consider
green spaces from a different perspective. Green planning is not just
about flora and fauna, but also about planning for economic benefits
[2]. It is worth trying to quantify the value of green spaces since
nature and landscape are crucially important to our quality of life and
sustainable development. The reality, however, is that urban
development often takes place at the expense of green spaces.
Urbanization is an ongoing process throughout the world; however,
hyper-urbanization without environmental planning is destructive,
not constructive [3]. Urban spaces are believed to be more valuable
than other land uses, particular green areas, simply because of the
market value connected to urban spaces. However, attractive
landscapes can help raise the quality and value of the urban market
even more. In order to reach these objectives of integrated planning,
the Green-Value-Gap needs to be bridged. Economists have to
understand the concept of Green-Planning and the spinoffs, and
Environmentalists have to understand the importance of urban
economic development and the benefits thereof to green planning. An
interface between Environmental Management, Economic
Development and sustainable Spatial Planning are needed to bridge
the Green-Value-Gap.
Abstract: This article presents the results using a parametric approach and a Wavelet Transform in analysing signals emitting from the sperm whale. The extraction of intrinsic characteristics of these unique signals emitted by marine mammals is still at present a difficult exercise for various reasons: firstly, it concerns non-stationary signals, and secondly, these signals are obstructed by interfering background noise. In this article, we compare the advantages and disadvantages of both methods: Auto Regressive models and Wavelet Transform. These approaches serve as an alternative to the commonly used estimators which are based on the Fourier Transform for which the hypotheses necessary for its application are in certain cases, not sufficiently proven. These modern approaches provide effective results particularly for the periodic tracking of the signal's characteristics and notably when the signal-to-noise ratio negatively effects signal tracking. Our objectives are twofold. Our first goal is to identify the animal through its acoustic signature. This includes recognition of the marine mammal species and ultimately of the individual animal (within the species). The second is much more ambitious and directly involves the intervention of cetologists to study the sounds emitted by marine mammals in an effort to characterize their behaviour. We are working on an approach based on the recordings of marine mammal signals and the findings from this data result from the Wavelet Transform. This article will explore the reasons for using this approach. In addition, thanks to the use of new processors, these algorithms once heavy in calculation time can be integrated in a real-time system.
Abstract: Developing a supply chain management (SCM) system is costly, but important. However, because of its complicated nature, not many of such projects are considered successful. Few research publications directly relate to key success factors (KSFs) for implementing a SCM system. Motivated by the above, this research proposes a hierarchy of KSFs for SCM system implementation in the semiconductor industry by using a two-step approach. First, the literature review indicates the initial hierarchy. The second step includes a focus group approach to finalize the proposed KSF hierarchy by extracting valuable experiences from executives and managers that actively participated in a project, which successfully establish a seamless SCM integration between the world's largest semiconductor foundry manufacturing company and the world's largest assembly and testing company. Future project executives may refer the resulting KSF hierarchy as a checklist for SCM system implementation in semiconductor or related industries.
Abstract: This paper at first presents approximate analytical
solutions for systems of fractional differential equations using the
differential transform method. The application of differential
transform method, developed for differential equations of integer
order, is extended to derive approximate analytical solutions of
systems of fractional differential equations. The solutions of our
model equations are calculated in the form of convergent series with
easily computable components. After that a drive-response
synchronization method with linear output error feedback is
presented for “generalized projective synchronization" for a class of
fractional-order chaotic systems via a scalar transmitted signal.
Genesio_Tesi and Duffing systems are used to illustrate the
effectiveness of the proposed synchronization method.
Abstract: Approximate tandem repeats in a genomic sequence are
two or more contiguous, similar copies of a pattern of nucleotides.
They are used in DNA mapping, studying molecular evolution
mechanisms, forensic analysis and research in diagnosis of inherited
diseases. All their functions are still investigated and not well
defined, but increasing biological databases together with tools for
identification of these repeats may lead to discovery of their specific
role or correlation with particular features. This paper presents a new
approach for finding approximate tandem repeats in a given sequence,
where the similarity between consecutive repeats is measured using
the Hamming distance. It is an enhancement of a method for finding
exact tandem repeats in DNA sequences based on the Burrows-
Wheeler transform.
Abstract: This paper reports on investigations into capacity of a
Multiple Input Multiple Output (MIMO) wireless communication
system employing a uniform linear array (ULA) at the transmitter and
either a uniform linear array (ULA) or a uniform circular array (UCA)
antenna at the receiver. The transmitter is assumed to be surrounded by
scattering objects while the receiver is postulated to be free from
scattering objects. The Laplacian distribution of angle of arrival
(AOA) of a signal reaching the receiver is postulated. Calculations of
the MIMO system capacity are performed for two cases without and
with the channel estimation errors. For estimating the MIMO channel,
the scaled least square (SLS) and minimum mean square error
(MMSE) methods are considered.