Abstract: The aim of the present work is to study the effect of annealing on the vibration damping capacity of high-chromium (16%) ferromagnetic steel. The alloys were prepared from raw materials of 99.9% purity melted in a high frequency induction furnace under high vacuum. The samples were heat-treated in vacuum at various temperatures (800 to 1200ºC) for 1 hour followed by slow cooling (120ºC/h). The inverted torsional pendulum method was used to evaluate the vibration damping capacity. The results indicated that the vibration damping capacity of the alloys is influenced by annealing and there exists a critical annealing temperature after 1000ºC. The damping capacity increases quickly below the critical temperature since the magnetic domains move more easily.
Abstract: A novel thermo-sensitive superabsorbent hydrogel
with salt- and pH-responsiveness properties was obtained by grafting
of mixtures of acrylic acid (AA) and N-isopropylacrylamide
(NIPAM) monomers onto kappa-carrageenan, kC, using ammonium
persulfate (APS) as a free radical initiator in the presence of
methylene bisacrylamide (MBA) as a crosslinker. Infrared
spectroscopy was carried out to confirm the chemical structure of the
hydrogel. Moreover, morphology of the samples was examined by
scanning electron microscopy (SEM). The effect of MBA
concentration and AA/NIPAM weight ratio on the water absorbency
capacity has been investigated. The swelling variations of hydrogels
were explained according to swelling theory based on the hydrogel
chemical structure. The hydrogels exhibited salt-sensitivity and
cation exchange properties. The temperature- and pH-reversibility
properties of the hydrogels make the intelligent polymers as good
candidates for considering as potential carriers for bioactive agents,
e.g. drugs.
Abstract: Empty Fruit Bunches (EFB) and Palm Oil Mill
Effluent (POME) are two main wastes from oil palm industries which
contain rich lignocellulose. Degradation of EFB and POME by
microorganisms will produce hydrolytic enzyme which will degrade
cellulose and hemicellulose during composting process. However,
normal composting takes about four to six months to reach maturity.
Hence, application of fungi into compost can shorten the period of
composting. This study identifies the effect of xylanase and cellulase
produced by Aspergillus niger and Trichoderma virens on
composting process using EFB and POME. The degradation of EFB
and POME indicates the lignocellulolytic capacity of Aspergillus
niger and Trichoderma virens with more than 7% decrease in
hemicellulose and more than 25% decrease in cellulose for both
inoculated compost. Inoculation of Aspergillus niger and
Trichoderma virens also increased the enzyme activities during the
composting period compared to the control compost by 21% for both
xylanase and cellulase. Rapid rise in the activities of cellulase and
xylanase was observed by Aspergillus niger with the highest
activities of 14.41 FPU/mg and 3.89 IU/mg, respectively. Increased
activities of cellulase and xylanase also occurred in inoculation of
Trichoderma virens with the highest activities obtained at 13.21
FPU/mg and 4.43 IU/mg, respectively. Therefore, it is evident that
the inoculation of fungi can increase the enzyme activities hence
effectively degrading the EFB and POME.
Abstract: This paper aims to develop an algorithm of finite
capacity material requirement planning (FCMRP) system for a multistage
assembly flow shop. The developed FCMRP system has two
main stages. The first stage is to allocate operations to the first and
second priority work centers and also determine the sequence of the
operations on each work center. The second stage is to determine the
optimal start time of each operation by using a linear programming
model. Real data from a factory is used to analyze and evaluate the
effectiveness of the proposed FCMRP system and also to guarantee a
practical solution to the user. There are five performance measures,
namely, the total tardiness, the number of tardy orders, the total
earliness, the number of early orders, and the average flow-time. The
proposed FCMRP system offers an adjustable solution which is a
compromised solution among the conflicting performance measures.
The user can adjust the weight of each performance measure to
obtain the desired performance. The result shows that the combination
of FCMRP NP3 and EDD outperforms other combinations
in term of overall performance index. The calculation time for the
proposed FCMRP system is about 10 minutes which is practical for
the planners of the factory.
Abstract: This study was to investigate the performance of
hybrid solvents blended between primary, secondary, or tertiary
amines and piperazine (PZ) for CO2 removal from flue gas in terms
of CO2 absorption capacity and regeneration efficiency at 90 oC.
Alkanolamines used in this work were monoethanolamine (MEA),
diethanolamine (DEA), and triethanolamine (TEA). The CO2
absorption was experimentally examined under atmospheric pressure
and room temperature. The results show that MEA blend with PZ
provided the maximum CO2 absorption capacity of 0.50 mol
CO2/mol amine while TEA provided the minimum CO2 absorption
capacity of 0.30 mol CO2/mol amine. TEA was easier to regenerate
for both first cycle and second cycle with less loss of absorption
capacity. The regeneration efficiency of TEA was 95.09 and 92.89 %,
for the first and second generation cycles, respectively.
Abstract: The malfunction of thermal protection system (TPS) caused by aerodynamic heating is a latent trouble to aircraft structure safety. Accurately predicting the structure temperature field is quite important for the TPS design of hypersonic vehicle. Since Thornton’s work in 1988, the coupled method of aerodynamic heating and heat transfer has developed rapidly. However, little attention has been paid to the influence of structural deformation on aerodynamic heating and structural temperature field. In the flight, especially the long-endurance flight, the structural deformation, caused by the aerodynamic heating and temperature rise, has a direct impact on the aerodynamic heating and structural temperature field. Thus, the coupled interaction cannot be neglected. In this paper, based on the method of static aero-thermo-elasticity, considering the influence of aero-thermo-elasticity deformation, the aerodynamic heating and heat transfer coupled results of hypersonic vehicle wing model were calculated. The results show that, for the low-curvature region, such as fuselage or center-section wing, structure deformation has little effect on temperature field. However, for the stagnation region with high curvature, the coupled effect is not negligible. Thus, it is quite important for the structure temperature prediction to take into account the effect of elastic deformation. This work has laid a solid foundation for improving the prediction accuracy of the temperature distribution of aircraft structures and the evaluation capacity of structural performance.
Abstract: Electrical distribution systems are incurring large losses as the loads are wide spread, inadequate reactive power compensation facilities and their improper control. A comprehensive static VAR compensator consisting of capacitor bank in five binary sequential steps in conjunction with a thyristor controlled reactor of smallest step size is employed in the investigative work. The work deals with the performance evaluation through analytical studies and practical implementation on an existing system. A fast acting error adaptive controller is developed suitable both for contactor and thyristor switched capacitors. The switching operations achieved are transient free, practically no need to provide inrush current limiting reactors, TCR size minimum providing small percentages of nontriplen harmonics, facilitates stepless variation of reactive power depending on load requirement so as maintain power factor near unity always. It is elegant, closed loop microcontroller system having the features of self regulation in adaptive mode for automatic adjustment. It is successfully tested on a distribution transformer of three phase 50 Hz, Dy11, 11KV/440V, 125 KVA capacity and the functional feasibility and technical soundness are established. The controller developed is new, adaptable to both LT & HT systems and practically established to be giving reliable performance.
Abstract: Subgrade moisture content varies with environmental and soil conditions and has significant influence on pavement performance. Therefore, it is important to establish realistic estimates of expected subgrade moisture contents to account for the effects of this variable on predicted pavement performance during the design stage properly. The initial boundary soil suction profile for a given pavement is a critical factor in determining expected moisture variations in the subgrade for given pavement and climatic and soil conditions. Several numerical models have been developed for predicting water and solute transport in saturated and unsaturated subgrade soils. Soil hydraulic properties are required for quantitatively describing water and chemical transport processes in soils by the numerical models. The required hydraulic properties are hydraulic conductivity, water diffusivity, and specific water capacity. The objective of this paper was to determine isothermal moisture profiles in a soil fill and predict the soil moisture movement above the ground water table using a simple one-dimensional finite difference model.
Abstract: Hopfield model of associative memory is studied in this work. In particular, two main problems that it possesses: the apparition of spurious patterns in the learning phase, implying the well-known effect of storing the opposite pattern, and the problem of its reduced capacity, meaning that it is not possible to store a great amount of patterns without increasing the error probability in the retrieving phase. In this paper, a method to avoid spurious patterns is presented and studied, and an explanation of the previously mentioned effect is given. Another technique to increase the capacity of a network is proposed here, based on the idea of using several reference points when storing patterns. It is studied in depth, and an explicit formula for the capacity of the network with this technique is provided.
Abstract: Human ability is a major source of constraint to manufacturing industries in Nigeria. This paper therefore, discusses the importance of human influences on manufacturing and consequently to industrialization and National development. In this paper, the development of manufacturing was anchored on two main factors; Infrastructural Capacity Development (ICD) and Human Capacity Development (HCD). However, a wider view was given to the HCD and the various contemporary human capacity issues militating against manufacturing in Nigeria. It went further to discuss various ways of acquiring and upgrading workers’ skills and finally, suggestions were made on how to tackle the onerous human capacity issues in manufacturing.
Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: This study describes the preparation of a novel proton
conducting membranes based on bacterial cellulose (BC) modified by
grafting of 2-acrylamido-2-methyl-1 -propanesulfonic acid (AMPS)
through UV-induced graft polymerization. These AMPS-g-BC
membranes have been characterized by various techniques including
FTIR, SEM and TGA, to find their successful grafting of AMPS on
BC, surface morphology and thermal stability, respectively. Physical
properties of AMPS-g-BC membranes have been assessed in terms of
Lamda value( λ ), ion exchange capacity(IEC) and proton
conductivity. The relationship between degree of grafting and AMPS
concentration used for grafting has been determined by weight gain
method. An optimum proton conductivity equal to 2.89x10-2 S cm-1
and IEC value equal to 1.79 mmol g-1 have been obtained when 20
wt% AMPS concentration is used for grafting (i.e. the corresponding
membrane is notated as AMPS20-g-BC).
Abstract: The dynamic spectrum allocation solutions such as
cognitive radio networks have been proposed as a key technology to
exploit the frequency segments that are spectrally underutilized.
Cognitive radio users work as secondary users who need to
constantly and rapidly sense the presence of primary users or
licensees to utilize their frequency bands if they are inactive. Short
sensing cycles should be run by the secondary users to achieve
higher throughput rates as well as to provide low level of interference
to the primary users by immediately vacating their channels once
they have been detected. In this paper, the throughput-sensing time
relationship in local and cooperative spectrum sensing has been
investigated under two distinct scenarios, namely, constant primary
user protection (CPUP) and constant secondary user spectrum
usability (CSUSU) scenarios. The simulation results show that the
design of sensing slot duration is very critical and depends on the
number of cooperating users under CPUP scenario whereas under
CSUSU, cooperating more users has no effect if the sensing time
used exceeds 5% of the total frame duration.
Abstract: Internet infrastructures in most places of the world
have been supported by the advancement of optical fiber technology,
most notably wavelength division multiplexing (WDM) system.
Optical technology by means of WDM system has revolutionized
long distance data transport and has resulted in high data capacity,
cost reductions, extremely low bit error rate, and operational
simplification of the overall Internet infrastructure. This paper
analyses and compares the system impairments, which occur at data
transmission rates of 2.5Gb/s and 10 Gb/s per wavelength channel in
our proposed optical WDM system for Internet infrastructure in
Tanzania. The results show that the data transmission rate of 2.5 Gb/s
has minimum system impairments compared with a rate of 10 Gb/s
per wavelength channel, and achieves a sufficient system
performance to provide a good Internet access service.
Abstract: Analytical procedure was carried out in this paper to
calculate the ultimate load capacity of reinforced concrete corbels
strengthened or repaired externally with CFRP sheets. Strut and tie
method and shear friction method proposed earlier for analyzing
reinforced concrete corbels were modified to incorporate the effect of
external CFRP sheets bonded to the corbel. The points of weakness
of any method that lead to an inaccuracy, especially when
overestimating test results were checked and discussed. Comparison
of prediction with the test data indicates that the ratio of test /
calculated ultimate load is 0.82 and 1.17 using strut and tie method
and shear friction method, respectively. If the limits of maximum
shear stress is followed, the calculated ultimate load capacity using
shear friction method was found to underestimates test data
considerably.
Abstract: Removal of Methylene Blue (MB) from aqueous
solution by adsorbing it on Gypsum was investigated by batch
method. The studies were conducted at 25°C and included the effects
of pH and initial concentration of Methylene Blue. The adsorption
data was analyzed by using the Langmuir, Freundlich and Tempkin
isotherm models. The maximum monolayer adsorption capacity was
found to be 36 mg of the dye per gram of gypsum. The data were
also analyzed in terms of their kinetic behavior and was found to
obey the pseudo second order equation.
Abstract: The presence of a vertical fatigue crack in the web of
a plate girder subjected to pure bending influences the bending
moment capacity of the girder. The growth of the crack may lead to
premature elastic failure due to flange local yielding, flange local
buckling, or web local buckling. Approximate expressions for the
bending moment capacities corresponding to these failure modes
were formulated. Finite element analyses were then used to validate
the expressions. The expressions were employed to assess the effects
of crack length on the capacity. Neglecting brittle fracture, tension
buckling, and ductile failure modes, it was found that typical girders
are governed by the capacity associated with flange local yielding as
influenced by the crack. Concluding, a possible use of the capacity
expressions in girder design was demonstrated.
Abstract: This research study the application of the immobilized
TiO2 layer and Cu-TiO2 layer on graphite substrate as a negative
electrode or anode for Li-ion battery. The titania layer was produced
through chemical bath deposition method, meanwhile Cu particles
were deposited electrochemically. A material can be used as an
electrode as it has capability to intercalates Li ions into its crystal
structure. The Li intercalation into TiO2/Graphite and Cu-
TiO2/Graphite were analyzed from the changes of its XRD pattern
after it was used as electrode during discharging process. The XRD
patterns were refined by Le Bail method in order to determine the
crystal structure of the prepared materials. A specific capacity and the
cycle ability measurement were carried out to study the performance
of the prepared materials as negative electrode of the Li-ion battery.
The specific capacity was measured during discharging process from
fully charged until the cut off voltage. A 300 was used as a load.
The result shows that the specific capacity of Li-ion battery with
TiO2/Graphite as negative electrode is 230.87 ± 1.70mAh.g-1 which is
higher than the specific capacity of Li-ion battery with pure graphite
as negative electrode, i.e 140.75 ±0.46mAh.g-1. Meanwhile
deposition of Cu onto TiO2 layer does not increase the specific
capacity, and the value even lower than the battery with
TiO2/Graphite as electrode. The cycle ability of the prepared battery
is only two cycles, due to the Li ribbon which was used as cathode
became fragile and easily broken.
Abstract: The deficit of power for electricity demand reaches
almost 30% for consumers in the last few years. This reflects with
continually increasing the price of electricity, and today the price for
small industry is almost 110Euro/MWh. The high price is additional
problem for the owners in the economy crisis which is reflected with
higher price of the goods.
The paper gives analyses of the energy needs for real agro
complex in Macedonia, private vinery with capacity of over 2 million
liters in a year and with self grapes and fruits fields. The existing
power supply is from grid with 10/04 kV transformer. The
geographical and meteorological condition of the vinery location
gives opportunity for including renewable as a power supply option
for the vinery complex.
After observation of the monthly energy needs for the vinery, the
base scenario is the existing power supply from the distribution grid.
The electricity bill in small industry has three factors: electricity in
high and low tariffs in kWh and the power engaged for the
technological process of production in kW. These three factors make
the total electricity bill and it is over 110 Euro/MWh which is the
price near competitive for renewable option. On the other side
investments in renewable (especially photovoltaic (PV)) has tendency
of decreasing with price of near 1,5 Euro/W. This means that
renewable with PV can be real option for power supply for small
industry capacities (under 500kW installed power).
Therefore, the other scenarios give the option with PV and the last
one includes wind option. The paper presents some scenarios for
power supply of the vinery as the followings:
• Base scenario of existing conventional power supply from the
grid
• Scenario with implementation of renewable of Photovoltaic
• Scenario with implementation of renewable of Photovoltaic and
Wind power
The total power installed in a vinery is near 570 kW, but the
maximum needs are around 250kW. At the end of the full paper some
of the results from scenarios will be presented. The paper also
includes the environmental impacts of the renewable scenarios, as
well as financial needs for investments and revenues from renewable.
Abstract: Theory of Constraints has been emerging as an
important tool for optimization of manufacturing/service systems.
Goldratt in his first book “ The Goal " gave the introduction on
Theory of Constraints and its applications in a factory scenario. A
large number of production managers around the globe read this book
but only a few could implement it in their plants because the book did
not explain the steps to implement TOC in the factory. To overcome
these limitations, Goldratt wrote this book to explain TOC, DBR and
the method to implement it. In this paper, an attempt has been made
to summarize the salient features of TOC and DBR listed in the book
and the correct approach to implement TOC in a factory setting. The
simulator available along with the book was actually used by the
authors and the claim of Goldratt regarding the use of DBR and
Buffer management to ease the work of production managers was
tested and was found to be correct.