Abstract: We study dynamic instability in high-rise steel moment
resisting frames (SMRFs) subjected to synthetic long-period ground
motions caused by hypothetical huge subduction earthquakes. Since
long duration as well as long dominant periods is a characteristic of
long-period ground motions, interstory drifts may enter the negative
postyield stiffness range many times when high-rise buildings are
subjected to long-period ground motions. Through the case studies of
9 high-rise SMRFs designed in accordance with the Japanese design
practice in 1980s, we demonstrate that drifting, or accumulation of
interstory drifts in one direction, occurs at the lower stories of the
SMRFs, if their natural periods are close to the dominant periods of the
long-period ground motions. The drifting led to residual interstory
drift ratio over 0.01, or to collapse if the design base shear was small.
Abstract: Due to the complex network architecture, the mobile
adhoc network-s multihop feature gives additional problems to the
users. When the traffic load at each node gets increased, the
additional contention due its traffic pattern might cause the nodes
which are close to destination to starve the nodes more away from the
destination and also the capacity of network is unable to satisfy the
total user-s demand which results in an unfairness problem. In this
paper, we propose to create an algorithm to compute the optimal
MAC-layer bandwidth assigned to each flow in the network. The
bottleneck links contention area determines the fair time share which
is necessary to calculate the maximum allowed transmission rate used
by each flow. To completely utilize the network resources, we
compute two optimal rates namely, the maximum fair share and
minimum fair share. We use the maximum fair share achieved in
order to limit the input rate of those flows which crosses the
bottleneck links contention area when the flows that are not allocated
to the optimal transmission rate and calculate the following highest
fair share. Through simulation results, we show that the proposed
protocol achieves improved fair share and throughput with reduced
delay.
Abstract: Several studies have shown the association between
ambient particulate matter (PM) and adverse health effects and
climate change, thus highlighting the need to limit the anthropogenic
sources of PM. PM Exposure is commonly monitored as mass
concentration of PM10 (particle aerodynamic diameter < 10μm) or
PM2.5 (particle aerodynamic diameter < 2.5μm), although increasing
toxicity with decreasing aerodynamic diameter has been reported due
to increased surface area and enhanced chemical reactivity with other
species. Additionally, the light scattering properties of PM increases
with decreasing size. Hence, it is important to study the chemical
characterization of finer fraction of the particulate matter and to
identify their sources so that they can be controlled appropriately to a
large extent at the sources before reaching to the receptors.
Abstract: The hypercube Qn is one of the most well-known
and popular interconnection networks and the k-ary n-cube Qk
n is
an enlarged family from Qn that keeps many pleasing properties
from hypercubes. In this article, we study the panpositionable
hamiltonicity of Qk
n for k ≥ 3 and n ≥ 2. Let x, y of V (Qk
n)
be two arbitrary vertices and C be a hamiltonian cycle of Qk
n.
We use dC(x, y) to denote the distance between x and y on the
hamiltonian cycle C. Define l as an integer satisfying d(x, y) ≤ l ≤ 1
2 |V (Qk
n)|. We prove the followings:
• When k = 3 and n ≥ 2, there exists a hamiltonian cycle C
of Qk
n such that dC(x, y) = l.
• When k ≥ 5 is odd and n ≥ 2, we request that l /∈ S
where S is a set of specific integers. Then there exists a
hamiltonian cycle C of Qk
n such that dC(x, y) = l.
• When k ≥ 4 is even and n ≥ 2, we request l-d(x, y) to be
even. Then there exists a hamiltonian cycle C of Qk
n such
that dC(x, y) = l.
The result is optimal since the restrictions on l is due to the
structure of Qk
n by definition.
Abstract: In this study we investigate silica nanoparticle (SiO2- NP) effects on the structure and phase properties of supported lipid monolayers and bilayers, coupling surface pressure measurements, fluorescence microscopy and atomic force microscopy. SiO2-NPs typically in size range of 10nm to 100 nm in diameter are tested. Our results suggest first that lipid molecules organization depends to their nature. Secondly, lipid molecules in the vinicity of big aggregates nanoparticles organize in liquid condensed phase whereas small aggregates are localized in both fluid liquid-expanded (LE) and liquid-condenced (LC). We demonstrated also by atomic force microscopy that by measuring friction forces it is possible to get information as if nanoparticle aggregates are recovered or not by lipid monolayers and bilayers.
Abstract: This paper describes how the correct endian mode of
the TMS320C6713 DSK board can be identified. It also explains how
the TMS320C6713 DSK board can be used in the little endian and in
the big endian modes for assembly language programming in
particular and for signal processing in general. Similarly, it discusses
how crucially important it is for a user of the TMS320C6713 DSK
board to identify the mode of operation and then use it correctly
during the development stages of the assembly language
programming; otherwise, it will cause unnecessary confusion and
erroneous results as far as storing data into the memory and loading
data from the memory is concerned. Furthermore, it highlights and
strongly recommends to the users of the TMS320C6713 DSK board
to be aware of the availability and importance of various display
options in the Code Composer Studio (CCS) for correctly
interpreting and displaying the desired data in the memory. The
information presented in this paper will be of great importance and
interest to those practitioners and developers who wants to use the
TMS320C6713 DSK board for assembly language programming as
well as input-output signal processing manipulations. Finally,
examples that clearly illustrate the concept are presented.
Abstract: Chronic diseases prevailed along with economic
growth as well as life style changed in recent years in Taiwan.
According to the governmental statistics, hypertension related disease
is the tenth of death causes with 1,816 died directly from hypertension
in 2010. There were more death causes amongst the top ten had been
proofed that having strong association with the hypertension, such as
heart diseases, cardiovascular diseases, and diabetes. Hypertension or
High blood pressure is one of the major indicators for chronic diseases,
and was generally perceived as the major causes of mortality. The
literature generally suggested that regular physical exercise was
helpful to prevent the occurrence or to ease the progress of a
hypertension. This paper reported the process and outcomes in
detailed of an improvement project of physical exercise intervention
specific for hypertension patients. Physical information were
measured before and after the project to obtain information such as
weight, waistline, cholesterol (HD & LD), blood examination, as well
as self-perceived health status. The intervention project involved a
six-week exercise program, of which contained three times a week, 30
minutes of tutored physical exercise intervention. The project had
achieved several gains in changing the subjects- behavior in terms of
many important biophysical indexes. Around 20% of the participants
had significantly improved their cholesterols, BMI, and changed
unhealthy behaviors. Results from the project were encouraging, and
would be good reference for other samples.
Abstract: Sedimentation is a hydraulic phenomenon that is
emerging as a serious challenge in river engineering. When the flow
reaches a certain state that gather potential energy, it shifts the
sediment load along channel bed. The transport of such materials can
be in the form of suspended and bed loads. The movement of these
along the river course and channels and the ways in which this could
influence the water intakes is considered as the major challenges for
sustainable O&M of hydraulic structures. This could be very serious
in arid and semi-arid regions like Iran, where inappropriate watershed
management could lead to shifting a great deal of sediments into the
reservoirs and irrigation systems. This paper aims to investigate
sedimentation in the Western Canal of Dez Diversion Weir in Iran,
identifying factors which influence the process and provide ways in
which to mitigate its detrimental effects by using the SHARC
Software.
For the purpose of this paper, data from the Dezful water authority
and Dezful Hydrometric Station pertinent to a river course of about 6
Km were used.
Results estimated sand and silt bed loads concentrations to be 193
ppm and 827ppm respectively. Given the available data on average
annual bed loads and average suspended sediment loads of 165ppm
and 837ppm, there was a significant statistical difference (16%)
between the sand grains, whereas no significant difference (1.2%)
was find in the silt grain sizes. One explanation for such finding
being that along the 6 Km river course there was considerable
meandering effects which explains recent shift in the hydraulic
behavior along the stream course under investigation. The sand
concentration in downstream relative to present state of the canal
showed a steep descending curve. Sediment trapping on the other
hand indicated a steep ascending curve. These occurred because the
diversion weir was not considered in the simulation model.
Abstract: In a product development process, understanding the functional behavior of the system, the role of components in achieving functions and failure modes if components/subsystem fails its required function will help develop appropriate design validation and verification program for reliability assessment. The integration of these three issues will help design and reliability engineers in identifying weak spots in design and planning future actions and testing program. This case study demonstrate the advantage of unascertained theory described in the subjective cognition uncertainty, and then applies blind number (BN) theory in describing the uncertainty of the mechanical system failure process and the same time used the same theory in bringing out another mechanical reliability system model. The practical calculations shows the BN Model embodied the characters of simply, small account of calculation but betterforecasting capability, which had the value of macroscopic discussion to some extent.
Abstract: This paper introduces an adiabatic register file based
on two-phase CPAL (Complementary Pass-Transistor Adiabatic
Logic circuits) with power-gating scheme, which can operate on a
single-phase power clock. A 32×32 single-phase adiabatic register file
with power-gating scheme has been implemented with TSMC 0.18μm
CMOS technology. All the circuits except for the storage cells employ
two-phase CPAL circuits, and the storage cell is based on the
conventional memory one. The two-phase non-overlap power-clock
generator with power-gating scheme is used to supply the proposed
adiabatic register file. Full-custom layouts are drawn. The energy and
functional simulations have been performed using the net-list
extracted from their layouts. Compared with the traditional static
CMOS register file, HSPICE simulations show that the proposed
adiabatic register file can work very well, and it attains about 73%
energy savings at 100 MHz.
Abstract: As originally designed for wired networks, TCP (transmission control protocol) congestion control mechanism is triggered into action when packet loss is detected. This implicit assumption for packet loss mostly due to network congestion does not work well in Mobile Ad Hoc Network, where there is a comparatively high likelihood of packet loss due to channel errors and node mobility etc. Such non-congestion packet loss, when dealt with by congestion control mechanism, causes poor TCP performance in MANET. In this study, we continue to investigate the impact of the interaction between transport protocols and on-demand routing protocols on the performance and stability of 802.11 multihop networks. We evaluate the important wireless networking events caused routing change, and propose a cross layer method to delay the unnecessary routing changes, only need to add a sensitivity parameter α , which represents the on-demand routing-s reaction to link failure of MAC layer. Our proposal is applicable to the plain 802.11 networking environment, the simulation results that this method can remarkably improve the stability and performance of TCP without any modification on TCP and MAC protocol.
Abstract: In this paper, we investigate the study of techniques
for scheduling users for resource allocation in the case of multiple
input and multiple output (MIMO) packet transmission systems. In
these systems, transmit antennas are assigned to one user or
dynamically to different users using spatial multiplexing. The
allocation of all transmit antennas to one user cannot take full
advantages of multi-user diversity. Therefore, we developed the case
when resources are allocated dynamically. At each time slot users
have to feed back their channel information on an uplink feedback
channel. Channel information considered available in the schedulers
is the zero forcing (ZF) post detection signal to interference plus
noise ratio. Our analysis study concerns the round robin and the
opportunistic schemes.
In this paper, we present an overview and a complete capacity
analysis of these schemes. The main results in our study are to give
an analytical form of system capacity using the ZF receiver at the
user terminal. Simulations have been carried out to validate all
proposed analytical solutions and to compare the performance of
these schemes.
Abstract: Personal name matching system is the core of
essential task in national citizen database, text and web mining,
information retrieval, online library system, e-commerce and record
linkage system. It has necessitated to the all embracing research in
the vicinity of name matching. Traditional name matching methods
are suitable for English and other Latin based language. Asian
languages which have no word boundary such as Myanmar language
still requires sounds alike matching system in Unicode based
application. Hence we proposed matching algorithm to get analogous
sounds alike (phonetic) pattern that is convenient for Myanmar
character spelling. According to the nature of Myanmar character, we
consider for word boundary fragmentation, collation of character.
Thus we use pattern conversion algorithm which fabricates words in
pattern with fragmented and collated. We create the Myanmar sounds
alike phonetic group to help in the phonetic matching. The
experimental results show that fragmentation accuracy in 99.32% and
processing time in 1.72 ms.
Abstract: This paper demonstrates an effort of a serviceoriented
engineering department in improving the sharing and
transfer of knowledge. Although the department consist of only six
employees, but it provides services in various chemical application in
an oil and gas business. The services provided span across Asia
Pacific region mainly Indonesia, Myanmar, Vietnam, Brunei,
Thailand and Singapore. Currently there are no effective tools or
integrated systems that support the sharing or transfer and
maintenance of knowledge so the department has considered
preserving this valuable knowledge by developing a Knowledge
Management System (KMS). This paper presents the development of
a KMS to support the sharing of knowledge in a service-oriented
engineering department of an oil and gas company. The embedded
features in the KMS like blog and forum will encourage iterative
process of knowledge sharing among the employees in the
department. The information and knowledge being shared, discussed
and communicated will be then achieved for future re-use. The re-use
of the knowledge allows the department to reduce redundant efforts
in providing consistent, up-to-date and cost effective of the best
solution to the its clients.
Abstract: In the present article, effect of non-uniform excitation
of reservoir bottom on nonlinear response of concrete gravity dams is
considered. Anisotropic damage mechanics approach is used to model nonlinear behavior of mass concrete in 2D space. The tallest
monolith of Pine Flat dam is selected as a case study. The horizontal
and vertical components of 1967 Koyna earthquake is used to excite
the system. It is found that crest response and stresses within the dam body decrease significantly when the reservoir is excited nonuniformly. In addition, the crack profiles within the dam body and in vicinity of the neck decreases.
Abstract: Baseball is unique among other sports in Taiwan.
Baseball has become a “symbol of the Taiwanese spirit and Taiwan-s
national sport". Taiwan-s first professional sports league, the Chinese
Professional Baseball League (CPBL), was established in 1989.
Starters pitch many more innings over the course of a season and for
a century teams have made all their best pitchers starters. In this
study, we attempt to determine the on-field performance these
pitchers and which won the most CPBL games in 2009. We utilize
the discriminate analysis approach to solve the problem, examining
winning pitchers and their statistics, to reliably find the best starting
pitcher. The data employed in this paper include innings pitched (IP),
earned runs allowed (ERA) and walks plus hits per inning pitched
(WPHIP) provided by the official website of the CPBL. The results
show that Aaron Rakers was the best starting pitcher of the CPBL.
The top 10 CPBL starting pitchers won 14 games to 8 games in the
2009 season. Though Fisher Discriminant Analysis, predicted to top
10 CPBL starting pitchers probably won 20 games to 9 games, more
1 game to 7 games in actually counts in 2009 season.
Abstract: This study proposes a materials procurement contracts
model to which the zero-cost collar option is applied for heading price
fluctuation risks in construction.The material contract model based on
the collar option that consists of the call option striking zone of the
construction company(the buyer) following the materials price
increase andthe put option striking zone of the material vendor(the
supplier) following a materials price decrease. This study first
determined the call option strike price Xc of the construction company
by a simple approach: it uses the predicted profit at the project starting
point and then determines the strike price of put option Xp that has an
identical option value, which completes the zero-cost material
contract.The analysis results indicate that the cost saving of the
construction company increased as Xc decreased. This was because the
critical level of the steel materials price increasewas set at a low level.
However, as Xc decreased, Xpof a put option that had an identical
option value gradually increased. Cost saving increased as Xc
decreased. However, as Xp gradually increased, the risk of loss from a
construction company increased as the steel materials price decreased.
Meanwhile, cost saving did not occur for the construction company,
because of volatility. This result originated in the zero-cost features of
the two-way contract of the collar option. In the case of the regular
one-way option, the transaction cost had to be subtracted from the cost
saving. The transaction cost originated from an option value that
fluctuated with the volatility. That is, the cost saving of the one-way
option was affected by the volatility. Meanwhile, even though the
collar option with zero transaction cost cut the connection between
volatility and cost saving, there was a risk of exercising the put option.
Abstract: Almost all universities include some form of assignment in their courses. The assignments are either carried out in either in groups or individually. To effectively manage these submitted assignments, a well-designed assignment submission system is needed, hence the need for an online assignment submission system to facilitate the distribution, and collection of assignments on due dates. The objective of such system is to facilitate interaction of lecturers and students for assessment and grading purposes. The aim of this study was to create a web based online assignment submission system for University of Mauritius. The system was created to eliminate the traditional process of giving an assignment and collecting the answers for the assignment. Lecturers can also create automated assessment to assess the students online. Moreover, the online submission system consists of an automatic mailing system which acts as a reminder for students about the deadlines of the posted assignments. System was tested to measure its acceptance rate among both student and lecturers.
Abstract: In this work, we are interested in developing a speech denoising tool by using a discrete wavelet packet transform (DWPT). This speech denoising tool will be employed for applications of recognition, coding and synthesis. For noise reduction, instead of applying the classical thresholding technique, some wavelet packet nodes are set to zero and the others are thresholded. To estimate the non stationary noise level, we employ the spectral entropy. A comparison of our proposed technique to classical denoising methods based on thresholding and spectral subtraction is made in order to evaluate our approach. The experimental implementation uses speech signals corrupted by two sorts of noise, white and Volvo noises. The obtained results from listening tests show that our proposed technique is better than spectral subtraction. The obtained results from SNR computation show the superiority of our technique when compared to the classical thresholding method using the modified hard thresholding function based on u-law algorithm.
Abstract: The current education system in India is adept in
equipping and assessing the scholastic development of children.
However, there is an immediate need to strengthen co-scholastic
areas like life-skills, values and attitudes to equip students to face real
life challenges. Audio-visual technology and their respective media
can make a significant contribution to a value based learning
curriculum. Thus, co-scholastic skills need to be effectively nurtured
by a medium that is entertaining and impactful. Films in general have
a tremendous impact in our society. Films with a positive message
make a formidable learning experience that can influence and inspire
generations of learners. Leveraging on this powerful medium,
EduMedia India Pvt. Ltd. has introduced School Cinema a well
researched film-based learning module supported by a fun and
exciting workbook, designed to introduce and reaffirm life-skills and
values to children, thereby having a positive influence on their
attitudes.