Abstract: A Comparison and evaluation of the different
condition monitoring (CM) techniques was applied experimentally
on RC e.g. Dynamic cylinder pressure and crankshaft Instantaneous
Angular Speed (IAS), for the detection and diagnosis of valve faults
in a two - stage reciprocating compressor for a programme of
condition monitoring which can successfully detect and diagnose a
fault in machine. Leakage in the valve plate was introduced
experimentally into a two-stage reciprocating compressor. The effect
of the faults on compressor performance was monitored and the
differences with the normal, healthy performance noted as a fault
signature been used for the detection and diagnosis of faults.
The paper concludes with what is considered to be a unique
approach to condition monitoring. First, each of the two most useful
techniques is used to produce a Truth Table which details the
circumstances in which each method can be used to detect and
diagnose a fault. The two Truth Tables are then combined into a
single Decision Table to provide a unique and reliable method of
detection and diagnosis of each of the individual faults introduced
into the compressor. This gives accurate diagnosis of compressor
faults.
Abstract: 17α-ethynylestradiol (EE2) is a synthetic estrogen
used as a key ingredient in an oral contraceptives pill. EE2 is an
endocrine disrupting compound, high in estrogenic potency.
Although EE2 exhibits low degree of biodegradability with common
microorganisms in wastewater treatment plants (WWTPs), this
compound can be biotransformed by ammonia-oxidizing bacteria
(AOB) via a co-metabolism mechanism in WWTPs. This study
aimed to investigate the effect of real wastewater on
biotransformation of EE2 by AOB. A preliminary experiment on the
effect of nitrite and pH levels on abiotic transformation of EE2
suggested that the abiotic transformation occurred at only pH
Abstract: The temporal nature of negative selection is an under exploited area. In a negative selection system, newly generated antibodies go through a maturing phase, and the survivors of the phase then wait to be activated by the incoming antigens after certain number of matches. These without having enough matches will age and die, while these with enough matches (i.e., being activated) will become active detectors. A currently active detector may also age and die if it cannot find any match in a pre-defined (lengthy) period of time. Therefore, what matters in a negative selection system is the dynamics of the involved parties in the current time window, not the whole time duration, which may be up to eternity. This property has the potential to define the uniqueness of negative selection in comparison with the other approaches. On the other hand, a negative selection system is only trained with “normal" data samples. It has to learn and discover unknown “abnormal" data patterns on the fly by itself. Consequently, it is more appreciate to utilize negation selection as a system for pattern discovery and recognition rather than just pattern recognition. In this paper, we study the potential of using negative selection in discovering unknown temporal patterns.
Abstract: Mining sequential patterns from large customer transaction databases has been recognized as a key research topic in database systems. However, the previous works more focused on mining sequential patterns at a single concept level. In this study, we introduced concept hierarchies into this problem and present several algorithms for discovering multiple-level sequential patterns based on the hierarchies. An experiment was conducted to assess the performance of the proposed algorithms. The performances of the algorithms were measured by the relative time spent on completing the mining tasks on two different datasets. The experimental results showed that the performance depends on the characteristics of the datasets and the pre-defined threshold of minimal support for each level of the concept hierarchy. Based on the experimental results, some suggestions were also given for how to select appropriate algorithm for a certain datasets.
Abstract: Experimental investigations were carried out in the
Manchester Tidal flow Facility (MTF) to study the flow patterns in
the region around and adjacent to a hypothetical headland in tidal
(oscillatory) ambient flow. The Planar laser-induced fluorescence
(PLIF) technique was used for visualization, with fluorescent dye
released at specific points around the headland perimeter and in its
adjacent recirculation zone. The flow patterns can be generalized into
the acceleration, stable flow and deceleration stages for each halfcycle,
with small variations according to location, which are more
distinct for low Keulegan-Carpenter number (KC) cases. Flow
patterns in the mixing region are unstable and complex, especially in
the recirculation zone. The flow patterns are in agreement with
previous visualizations, and support previous results in steady
ambient flow. It is suggested that the headland lee could be a viable
location for siting of pollutant outfalls.
Abstract: Sliding mode control with a fuzzy boundary layer is presented to hydraulic position control problem in this paper. A nonlinear hydraulic servomechanism which has an asymmetric cylinder is modeled and simulated first, then the proposed control scheme is applied to this model versus the conventional sliding mode control. Simulation results proved that the chattering free position control is achieved by tuning the fuzzy scaling factors properly.
Abstract: The purpose of this paper is to solve the problem of protecting aerial lines from high impedance faults (HIFs) in distribution systems. This investigation successfully applies 3I0 zero sequence current to solve HIF problems. The feature extraction system based on discrete wavelet transform (DWT) and the feature identification technique found on statistical confidence are then applied to discriminate effectively between the HIFs and the switch operations. Based on continuous wavelet transform (CWT) pattern recognition of HIFs is proposed, also. Staged fault testing results demonstrate that the proposed wavelet based algorithm is feasible performance well.
Abstract: In recent years, scanning probe atomic force
microscopy SPM AFM has gained acceptance over a wide spectrum
of research and science applications. Most fields focuses on physical,
chemical, biological while less attention is devoted to manufacturing
and machining aspects. The purpose of the current study is to assess
the possible implementation of the SPM AFM features and its
NanoScope software in general machining applications with special
attention to the tribological aspects of cutting tool. The surface
morphology of coated and uncoated as-received carbide inserts is
examined, analyzed, and characterized through the determination of
the appropriate scanning setting, the suitable data type imaging
techniques and the most representative data analysis parameters
using the MultiMode SPM AFM in contact mode. The NanoScope
operating software is used to capture realtime three data types
images: “Height", “Deflection" and “Friction". Three scan sizes are
independently performed: 2, 6, and 12 μm with a 2.5 μm vertical
range (Z). Offline mode analysis includes the determination of three
functional topographical parameters: surface “Roughness", power
spectral density “PSD" and “Section". The 12 μm scan size in
association with “Height" imaging is found efficient to capture every
tiny features and tribological aspects of the examined surface. Also,
“Friction" analysis is found to produce a comprehensive explanation
about the lateral characteristics of the scanned surface. Configuration
of many surface defects and drawbacks has been precisely detected
and analyzed.
Abstract: A simple mobile engine-driven pneumatic paddy
collector made of locally available materials using local
manufacturing technology was designed, fabricated, and tested for
collecting and bagging of paddy dried on concrete pavement. The
pneumatic paddy collector had the following major components:
radial flat bladed type centrifugal fan, power transmission system,
bagging area, frame and the conveyance system. Results showed
significant differences on the collecting capacity, noise level, and fuel
consumption when rotational speed of the air mover shaft was varied.
Other parameters such as collecting efficiency, air velocity,
augmented cracked grain percentage, and germination rate were not
significantly affected by varying rotational speed of the air mover
shaft. The pneumatic paddy collector had a collecting efficiency of
99.33 % with a collecting capacity of 2685.00 kg/h at maximum
rotational speed of centrifugal fan shaft of about 4200 rpm. The
machine entailed an investment cost of P 62,829.25. The break-even
weight of paddy was 510,606.75 kg/yr at a collecting cost of 0.11
P/kg of paddy. Utilizing the machine for 400 hours per year
generated an income of P 23,887.73. The projected time needed to
recover cost of the machine based on 2685 kg/h collecting capacity
was 2.63 year.
Abstract: In the past few decades, researchers have witnessed a
paradigm shift in Human Resource Management-from individual
performance to organizational outcomes with the role of Human
resource (HR) managers becoming increasingly significant to the
organization. In such a context, it is important to examine HR
practices from a strategic perspective on the sustained competitive
advantage (SCA) of the organizations. The present study explores
how Indian organisations look at their human resources strategically
when faced with competitive environment. Also, it explores strategic
initiatives being taken to manage human resources within the
organisations and how these initiatives promote SCA in terms of
enhancing the overall customer-centric delivery of goods and
services.
Abstract: Fungal infections are becoming more common and the
range of susceptible individuals has expanded. While Candida
albicans remains the most common infective species, other Candida
spp. are becoming increasingly significant. In a range of large-scale
studies of candidaemia between 1999 and 2006, about 52% of 9717
cases involved C. albicans, about 30% involved either C. glabrata or
C. parapsilosis and less than 15% involved C. tropicalis, C. krusei or
C. guilliermondii. However, the probability of mortality within 30
days of infection with a particular species was at least 40% for C.
tropicalis, C. albicans, C. glabrata and C. krusei and only 22% for
C. parapsilopsis. Clinical isolates of Candida spp. grew at rates
ranging from 1.65 h-1 to 4.9 h-1. Three species (C. krusei, C. albicans
and C. glabrata) had relatively high growth rates (μm > 4 h-1), C.
tropicalis and C. dubliniensis grew moderately quickly (Ôëê 3 h-1) and
C. parapsilosis and C. guilliermondii grew slowly (< 2 h-1). Based
on these data, the log of the odds of mortality within 30 days of
diagnosis was linearly related to μm. From this the underlying
probability of mortality is 0.13 (95% CI: 0.10-0.17) and it increases
by about 0.09 ± 0.02 for each unit increase in μm. Given that the
overall crude mortality is about 0.36, the growth of Candida spp.
approximately doubles the rate, consistent with the results of larger
case-matched studies of candidaemia.
Abstract: In this study, rotating flexible shaft-disk system
having flexible beams is considered as a dynamic system. After
neglecting nonlinear terms, torsional vibration of the shaft-disk
system and lateral and longitudinal vibration of the flexible beam are
still coupled through the motor speed. The system has three natural
frequencies; the flexible shaft-disk system torsional natural
frequency, the flexible beam lateral and longitudinal natural
frequencies. Eigenvalue calculations show that while the shaft speed
changes, torsional natural frequency of the shaft-disk system and the
beam longitudinal natural frequency are not changing but the beam
lateral natural frequency changes. Beam lateral natural frequency
stays the same as the nonrotating beam lateral natural frequency ωb
until the motor speed ωm is equal to ωb. After then ωb increases and
remains equal to the motor speed ωm until the motor speed is equal to
the shaft-disk system natural frequency ωT. Then the beam lateral
natural frequency ωb becomes equal to the natural frequency ωT and
stays same while the motor speed ωm is increased. Modal amplitudes
and phase angles of the vibrations are also plotted against the motor
speed ωm.
Abstract: IETF defines mobility support in IPv6, i.e. MIPv6, to
allow nodes to remain reachable while moving around in the IPv6
internet. When a node moves and visits a foreign network, it is still
reachable through the indirect packet forwarding from its home
network. This triangular routing feature provides node mobility but
increases the communication latency between nodes. This deficiency
can be overcome by using a Binding Update (BU) scheme, which let
nodes keep up-to-date IP addresses and communicate with each other
through direct IP routing. To further protect the security of BU, a
Return Routability (RR) procedure was developed. However, it has
been found that RR procedure is vulnerable to many attacks. In this
paper, we will propose a lightweight RR procedure based on
geometric computing. In consideration of the inherent limitation of
computing resources in mobile node, the proposed scheme is
developed to minimize the cost of computations and to eliminate the
overhead of state maintenance during binding updates. Compared with
other CGA-based BU schemes, our scheme is more efficient and
doesn-t need nonce tables in nodes.
Abstract: There are several approaches for handling multiclass classification. Aside from one-against-one (OAO) and one-against-all (OAA), hierarchical classification technique is also commonly used. A binary classification tree is a hierarchical classification structure that breaks down a k-class problem into binary sub-problems, each solved by a binary classifier. In each node, a set of classes is divided into two subsets. A good class partition should be able to group similar classes together. Many algorithms measure similarity in term of distance between class centroids. Classes are grouped together by a clustering algorithm when distances between their centroids are small. In this paper, we present a binary classification tree with tuned observation-based clustering (BCT-TOB) that finds a class partition by performing clustering on observations instead of class centroids. A merging step is introduced to merge any insignificant class split. The experiment shows that performance of BCT-TOB is comparable to other algorithms.
Abstract: Information sharing and exchange, rather than
information processing, is what characterizes information
technology in the 21st century. Ontologies, as shared common
understanding, gain increasing attention, as they appear as the
most promising solution to enable information sharing both at
a semantic level and in a machine-processable way. Domain
Ontology-based modeling has been exploited to provide
shareability and information exchange among diversified,
heterogeneous applications of enterprises.
Contextual ontologies are “an explicit specification of
contextual conceptualization". That is: ontology is
characterized by concepts that have multiple representations
and they may exist in several contexts. Hence, contextual
ontologies are a set of concepts and relationships, which are
seen from different perspectives. Contextualization is to allow
for ontologies to be partitioned according to their contexts.
The need for contextual ontologies in enterprise modeling
has become crucial due to the nature of today's competitive
market. Information resources in enterprise is distributed and
diversified and is in need to be shared and communicated
locally through the intranet and globally though the internet.
This paper discusses the roles that ontologies play in an
enterprise modeling, and how ontologies assist in building a
conceptual model in order to provide communicative and
interoperable information systems. The issue of enterprise
modeling based on contextual domain ontology is also
investigated, and a framework is proposed for an enterprise
model that consists of various applications.
Abstract: Heat-inducible gene expression vectors are useful for hyperthermia-induced cancer gene therapy, because the combination
of hyperthermia and gene therapy can considerably improve the therapeutic effects. In the present study, we developed an enhanced
heat-inducible transgene expression system in which a heat-shock
protein (HSP) promoter and tetracycline-responsive transactivator
were combined. When the transactivator plasmid containing the
tetracycline-responsive transactivator gene was co-transfected with
the reporter gene expression plasmid, a high level of heat-induced gene expression was observed compared with that using the HSP
promoter without the transactivator. In vitro evaluation of the
therapeutic effect using HeLa cells showed that heat-induced therapeutic gene expression caused cell death in a high percentage of
these cells, indicating that this strategy is promising for cancer gene therapy.
Abstract: In this paper, we present local image descriptor using
VQ-SIFT for more effective and efficient image retrieval. Instead of
SIFT's weighted orientation histograms, we apply vector quantization
(VQ) histogram as an alternate representation for SIFT features.
Experimental results show that SIFT features using VQ-based local
descriptors can achieve better image retrieval accuracy than the
conventional algorithm while the computational cost is significantly
reduced.
Abstract: This study examines the possibility to apply the theory of multidimensional accounting (momentum accounting) in a Brazilian Navy-s Services Provider Military Organization (Organização Militar Prestadora de Serviços - OMPS). In general, the core of the said theory is the fact that Accounting does not recognize the inertia of transactions occurring in an entity, and that occur repeatedly in some cases, regardless of the implementation of new actions by its managers. The study evaluates the possibility of greater use of information recorded in the financial statements of the unit of analysis, within the strategic decisions of the organization. As a research strategy, we adopted the case study. The results infer that it is possible to use the theory in the context of a multidimensional OMPS, promoting useful information for decision-making and thereby contributing to the strengthening of the necessary alignment of its administration with the current desires of the Brazilian society.
Abstract: In this paper, the modified optimal sliding mode control with a proposed method to design a sliding surface is presented. Because of the inability of the previous approach of the sliding mode method to design a bounded and suitable input, the new variation is proposed in the sliding manifold to obviate problems in a structural system. Although the sliding mode control is a powerful method to reject disturbances and noises, the chattering problem is not good for actuators. To decrease the chattering phenomena, the optimal control is added to the sliding mode control. Not only the proposed method can decline the intense variations in the inputs of the system but also it can produce the efficient responses respect to the sliding mode control and optimal control that are shown by performing some numerical simulations.
Abstract: Recent theorizations on the cognitive process of moral
judgment have focused on the role of intuitions and emotions, marking
a departure from previous emphasis on conscious, step-by-step
reasoning. My study investigated how being in a disgusted mood state
affects moral judgment.
Participants were induced to enter a disgusted mood state through
listening to disgusting sounds and reading disgusting descriptions.
Results shows that they, when compared to control who have not been
induced to feel disgust, are more likely to endorse actions that are
emotionally aversive but maximizes utilitarian return
The result is analyzed using the 'emotion-as-information' approach
to decision making. The result is consistent with the view that
emotions play an important role in determining moral judgment.