Abstract: Recently, the Field Programmable Gate Array (FPGA) technology offers the potential of designing high performance systems at low cost. The discrete wavelet transform has gained the reputation of being a very effective signal analysis tool for many practical applications. However, due to its computation-intensive nature, current implementation of the transform falls short of meeting real-time processing requirements of most application. The objectives of this paper are implement the Haar and Daubechies wavelets using FPGA technology. In addition, the Bit Error Rate (BER) between the input audio signal and the reconstructed output signal for each wavelet is calculated. From the BER, it is seen that the implementations execute the operation of the wavelet transform correctly and satisfying the perfect reconstruction conditions. The design procedure has been explained and designed using the stat-ofart Electronic Design Automation (EDA) tools for system design on FPGA. Simulation, synthesis and implementation on the FPGA target technology has been carried out.
Abstract: Public procurement is one of the most
important areas in the public sector that introduces a possibility for a
corruption. Due to the volume of the funds that are
allocated through this institution (in the EU countries it is between 10
– 15% of GDP), it has very serious implications for the efficiency of
public expenditures and the overall economic efficiency as
well. Indicators that are usually used for the measurement of the
corruption (such as Corruption Perceptions Index - CPI) show that
the worst situation is in the post-communist countries
and Mediterranean countries.
The presented paper uses the Czech Republic as an example of a
post-communist country and analyses the factors which influence
the scope of corruption in public procurement. Moreover, the
paper discusses indicators that could point at the public procurement
market inefficiency. The presented results show that post-communist
states use the institute of public contracts significantly more than the
old member countries of the continental Europe. It has a very
important implication because it gives more space for corruption.
Furthermore, it appears that the inefficient functioning of public
procurement market is clearly manifested in the low number of bids,
low level of market transparency and an ineffective control
system. Some of the observed indicators are statistically significantly
correlated with the CPI.
Abstract: This article is presented an experimental and modeling
study of a four-bed pressure swing adsorption process using
zeolite13X to provide oxygen-enriched air. The binary mixture N2/O2
(79/21 vol %) was used as a feed stream. The effects of purge/feed
ratio (P/F), adsorption pressure, cyclic time and product flow rate on
product purity and recovery under nonisothermal condition were
studied. The adsorption dynamics of process were determined using
a mathematical model incorporated mass and energy balances. A
Mathlab code using finite difference method was developed to solve
the set of coupled differential-algebraic equations, and the simulation
results are agreed well with experimental results.
Abstract: This paper examines the available experiment data for a copper bromide vapor laser (CuBr laser), emitting at two wavelengths - 510.6 and 578.2nm. Laser output power is estimated based on 10 independent input physical parameters. A classification and regression tree (CART) model is obtained which describes 97% of data. The resulting binary CART tree specifies which input parameters influence considerably each of the classification groups. This allows for a technical assessment that indicates which of these are the most significant for the manufacture and operation of the type of laser under consideration. The predicted values of the laser output power are also obtained depending on classification. This aids the design and development processes considerably.
Abstract: Mammalian genomes contain large number of
retroelements (SINEs, LINEs and LTRs) which could affect
expression of protein coding genes through associated transcription
factor binding sites (TFBS). Activity of the retroelement-associated
TFBS in many genes is confirmed experimentally but their global
functional impact remains unclear. Human SINEs (Alu repeats) and
mouse SINEs (B1 and B2 repeats) are known to be clustered in GCrich
gene rich genome segments consistent with the view that they
can contribute to regulation of gene expression. We have shown
earlier that Alu are involved in formation of cis-regulatory modules
(clusters of TFBS) in human promoters, and other authors reported
that Alu located near promoter CpG islands have an increased
frequency of CpG dinucleotides suggesting that these Alu are
undermethylated. Human Alu and mouse B1/B2 elements have an
internal bipartite promoter for RNA polymerase III containing
conserved sequence motif called B-box which can bind basal
transcription complex TFIIIC. It has been recently shown that TFIIIC
binding to B-box leads to formation of a boundary which limits
spread of repressive chromatin modifications in S. pombe. SINEassociated
B-boxes may have similar function but conservation of
TFIIIC binding sites in SINEs located near mammalian promoters
has not been studied earlier. Here we analysed abundance and
distribution of retroelements (SINEs, LINEs and LTRs) in annotated
sequences of the Database of mammalian transcription start sites
(DBTSS). Fractions of SINEs in human and mouse promoters are
slightly lower than in all genome but >40% of human and mouse
promoters contain Alu or B1/B2 elements within -1000 to +200 bp
interval relative to transcription start site (TSS). Most of these SINEs
is associated with distal segments of promoters (-1000 to -200 bp
relative to TSS) indicating that their insertion at distances >200 bp
upstream of TSS is tolerated during evolution. Distribution of SINEs
in promoters correlates negatively with the distribution of CpG
sequences. Using analysis of abundance of 12-mer motifs from the
B1 and Alu consensus sequences in genome and DBTSS it has been
confirmed that some subsegments of Alu and B1 elements are poorly
conserved which depends in part on the presence of CpG
dinucleotides. One of these CpG-containing subsegments in B1
elements overlaps with SINE-associated B-box and it shows better
conservation in DBTSS compared to genomic sequences. It has been
also studied conservation in DBTSS and genome of the B-box
containing segments of old (AluJ, AluS) and young (AluY) Alu
repeats and found that CpG sequence of the B-box of old Alu is
better conserved in DBTSS than in genome. This indicates that Bbox-
associated CpGs in promoters are better protected from
methylation and mutation than B-box-associated CpGs in genomic
SINEs. These results are consistent with the view that potential
TFIIIC binding motifs in SINEs associated with human and mouse
promoters may be functionally important. These motifs may protect
promoters from repressive histone modifications which spread from
adjacent sequences. This can potentially explain well known
clustering of SINEs in GC-rich gene rich genome compartments and
existence of unmethylated CpG islands.
Abstract: In this paper we consider a nonlinear feedback control called augmented automatic choosing control (AACC) for nonlinear systems with constrained input. Constant terms which arise from section wise linearization of a given nonlinear system are treated as coefficients of a stable zero dynamics.Parameters included in the control are suboptimally selectedby extremizing a combination of Hamiltonian and Lyapunov functions with the aid of the genetic algorithm. This approach is applied to a field excitation control problem of power system to demonstrate the splendidness of the AACC. Simulation results show that the new controller can improve performance remarkably well.
Abstract: A new and cost effective RP-HPLC method was
developed and validated for simultaneous analysis of non steroidal
anti inflammatory dugs Diclofenac sodium (DFS), Flurbiprofen
(FLP) and an opioid analgesic Tramadol (TMD) in advanced drug
delivery systems (Liposome and Microcapsules), marketed brands
and human plasma. Isocratic system was employed for the flow of
mobile phase consisting of 10 mM sodium dihydrogen phosphate
buffer and acetonitrile in molar ratio of 67: 33 with adjusted pH of
3.2. The stationary phase was hypersil ODS column (C18, 250×4.6
mm i.d., 5 μm) with controlled temperature of 30 C°. DFS in
liposomes, microcapsules and marketed drug products was
determined in range of 99.76-99.84%. FLP and TMD in
microcapsules and brands formulation were 99.78 - 99.94 % and
99.80 - 99.82 %, respectively. Single step liquid-liquid extraction
procedure using combination of acetonitrile and trichloroacetic acid
(TCA) as protein precipitating agent was employed. The detection
limits (at S/N ratio 3) of quality control solutions and plasma samples
were 10, 20, and 20 ng/ml for DFS, FLP and TMD, respectively.
The Assay was acceptable in linear dynamic range. All other
validation parameters were found in limits of FDA and ICH method
validation guidelines. The proposed method is sensitive, accurate and
precise and could be applicable for routine analysis in
pharmaceutical industry as well as in human plasma samples for
bioequivalence and pharmacokinetics studies.
Abstract: This paper proposes an adaptive sliding mode
controller which combines adaptive control and sliding
mode control to control a nonlinear robotic manipulator
with uncertain parameters. We use an adaptive algorithm
based on the concept of sliding mode control to alleviate the
chattering phenomenon of control input. Adaptive laws are
developed to obtain the gain of switching input and the
boundary layer parameters. The stability and convergence
of the robotic manipulator control system are guaranteed
by applying the Lyapunov theorem. Simulation results
demonstrate that the chattering of control input can be
alleviated effectively. The proposed controller scheme can
assure robustness against a large class of uncertainties and
achieve good trajectory tracking performance.
Abstract: A graph G is fractional k-covered if for each edge e of
G, there exists a fractional k-factor h, such that h(e) = 1. If k = 2,
then a fractional k-covered graph is called a fractional 2-covered
graph. The binding number bind(G) is defined as follows,
bind(G) = min{|NG(X)|
|X|
: ├ÿ = X Ôèå V (G),NG(X) = V (G)}.
In this paper, it is proved that G is fractional 2-covered if δ(G) ≥ 4
and bind(G) > 5
3 .
Abstract: Web-based systems have become increasingly
important due to the fact that the Internet and the World Wide Web
have become ubiquitous, surpassing all other technological
developments in our history. The Internet and especially companies
websites has rapidly evolved in their scope and extent of use, from
being a little more than fixed advertising material, i.e. a "web
presences", which had no particular influence for the company's
business, to being one of the most essential parts of the company's
core business.
Traditional software engineering approaches with process models
such as, for example, CMM and Waterfall models, do not work very
well since web system development differs from traditional
development. The development differs in several ways, for example,
there is a large gap between traditional software engineering designs
and concepts and the low-level implementation model, many of the
web based system development activities are business oriented (for
example web application are sales-oriented, web application and
intranets are content-oriented) and not engineering-oriented.
This paper aims to introduce Increment Iterative extreme
Programming (IIXP) methodology for developing web based
systems. In difference to the other existence methodologies, this
methodology is combination of different traditional and modern
software engineering and web engineering principles.
Abstract: We present a preliminary x-ray study on human-hair
microstructures for a health-state indicator, in particular a cancer
case. As an uncomplicated and low-cost method of x-ray technique,
the human-hair microstructure was analyzed by wide-angle x-ray
diffractions (XRD) and small-angle x-ray scattering (SAXS). The
XRD measurements exhibited the simply reflections at the d-spacing
of 28 Å, 9.4 Å and 4.4 Å representing to the periodic distance of the
protein matrix of the human-hair macrofibrous and the diameter and
the repeated spacing of the polypeptide alpha helixes of the
photofibrils of the human-hair microfibrous, respectively. When
compared to the normal cases, the unhealthy cases including to the
breast- and ovarian-cancer cases obtained higher normalized ratios of
the x-ray diffracting peaks of 9.4 Å and 4.4 Å. This likely resulted
from the varied distributions of microstructures by a molecular
alteration. As an elemental analysis by x-ray fluorescence (XRF), the
normalized quantitative ratios of zinc(Zn)/calcium(Ca) and
iron(Fe)/calcium(Ca) were determined. Analogously, both Zn/Ca and
Fe/Ca ratios of the unhealthy cases were obtained higher than both of
the normal cases were. Combining the structural analysis by XRD
measurements and the elemental analysis by XRF measurements
exhibited that the modified fibrous microstructures of hair samples
were in relation to their altered elemental compositions. Therefore,
these microstructural and elemental analyses of hair samples will be
benefit to associate with a diagnosis of cancer and genetic diseases.
This functional method would lower a risk of such diseases by the
early diagnosis. However, the high-intensity x-ray source, the highresolution
x-ray detector, and more hair samples are necessarily
desired to develop this x-ray technique and the efficiency would be
enhanced by including the skin and fingernail samples with the
human-hair analysis.
Abstract: Pure phase gallosilicate nitrite sodalite has been synthesized in a single step by low temperature (373 oK) hydrothermal technique. The product obtained was characterized using a combination of techniques including X-ray powder diffraction, IR, Raman spectroscopy, SEM, MAS NMR spectroscopy as well as thermogravimetry. Sodalite with an ideal composition was obtained after synthesis at 3730K and seven days duration using alkaline medium. The structural features of the Na8[GaSiO4]6(NO2)2 sodalite were investigated by IR, MAS NMR spectroscopy of 29Si and 23Na nuclei and by Reitveld refinement of X-ray powder diffraction data. The crystal structure of this sodalite has been refined in the space group P 4 3n; with a cell parameter 8.98386Å, V= 726.9 Å, (Rwp= 0.077 and Rp=0.0537) and Si-O-Ga angle is found to be 132.920 . MAS NMR study confirms complete ordering of Si and Ga in the gallosilicate framework. The surface area of single entity with stoichiometry Na8[GaSiO4]6(NO2)2 was found to be 8.083 x10-15 cm2/g.
Abstract: In mammalian reproductive tract, the oviduct secretes
huge number of growth factors and cytokines that create an optimal
micro-environment for the initial stages of preimplantation embryos.
Secretion of these growth factors is stage-specific. Among them,
VEGF is a potent mitogen for vascular endothelium and stimulates
vascular permeability. Apart from angiogenesis, VEGF in the oviduct
may be involved in regulating the oocyte maturation and subsequent
developmental process during embryo production in vitro. In
experiment 1, to evaluate the effect of VEGF during IVM of porcine
COC and subsequent developmental ability after PA and SCNT. The
results from these experiments indicated that maturation rates among
the different VEGF concentrations were not significant different. In
experiment 2, total intracellular GSH concentrations of oocytes
matured with VEGF (5-50 ng/ml) were increased significantly
compared to a control and VEGF group (500 ng/ml). In experiment 3,
the blastocyst formation rates and total cell number per blastocyst
after parthenogenesis of oocytes matured with VEGF (5-50 ng/ml)
were increased significantly compared to a control and VEGF group
(500 ng/ml). Similarly, in experiment 4, the blastocyst formation rate
and total cell number per blastocyst after SCNT and IVF of oocytes
matured with VEGF (5 ng/ml) were significantly higher than that of
oocytes matured without VEGF group. In experiment 5, at 10 hour
after the onset of IVF, pronuclear formation rate was evaluated.
Monospermy was significantly higher in VEGF-matured oocytes than
in the control, and polyspermy and sperm penetration per oocyte
were significantly higher in the control group than in the VEGFmatured
oocytes. Supplementation with VEGF during IVM
significantly improved male pronuclear formation as compared with
the control. In experiment 6, type III cortical granule distribution in
oocytes was more common in VEGF-matured oocytes than in the
control. In conclusion, the present study suggested that
supplementation of VEGF during IVM may enhance the
developmental potential of porcine in vitro embryos through increase
of the intracellular GSH level, higher MPN formation and increased
fertilization rate as a consequence of an improved cytoplasmic
maturation.
Abstract: Objective of this study was to study and compare the effectiveness of inspectors who had different workloads for feed forward and feedback training. The visual search task was simulated to search for specified alphabets called defects. These defects were included of four alphabets in Thai and English such as s ภ, ถ, X, and V with different background. These defects were combined in the specified alphabets and were given the different three backgrounds i.e., Thai, English, and mixed English and Thai alphabets. Sixty students were chosen as a sample in this study and test for final selection subject. Finally, five subjects were taken into testing process. They were asked to search for defects after they were provided basic information. Experiment design was used factorial design and subjects were trained for feed forward and the feedback training. The results show that both trainings were affected on mean search time. It was also found that the feedback training can increase the effectiveness of visual inspectors rather than the feed forward training significantly different at the level of .05
Abstract: In this study we present the effect of elevated
temperatures from 300K to 400K on the electrical properties of
copper Phthalocyanine (CuPc) based organic field effect transistors
(OFET). Thin films of organic semiconductor CuPc (40nm) and
semitransparent Al (20nm) were deposited in sequence, by vacuum
evaporation on a glass substrate with previously deposited Ag source
and drain electrodes with a gap of 40 μm. Under resistive mode of
operation, where gate was suspended it was observed that drain
current of this organic field effect transistor (OFET) show an
increase with temperature. While in grounded gate condition metal
(aluminum) – semiconductor (Copper Phthalocyanine) Schottky
junction dominated the output characteristics and device showed
switching effect from low to high conduction states like Zener diode
at higher bias voltages. This threshold voltage for switching effect
has been found to be inversely proportional to temperature and shows
an abrupt decrease after knee temperature of 360K. Change in
dynamic resistance (Rd = dV/dI) with respect to temperature was
observed to be -1%/K.
Abstract: The presence of a vertical edge-crack within a web
plate subjected to pure bending induces local compressive stresses
about the crack which may cause tension buckling. Approximate
theoretical expressions were derived for the critical far-field tensile
stress and bending moment capacity of an edge-cracked web plate
associated with tension buckling. These expressions were validated
with finite element analyses and used to investigate the possibility of
tension buckling in web-cracked trial girders. It was found that
tension buckling is an unlikely occurrence unless the web is relatively
thin or the crack is very long.
Abstract: In this paper, an magnetorheological (MR) mount with
fuzzy sliding mode controller (FSMC) is studied for vibration
suppression when the system is subject to base excitations. In recent
years, magnetorheological fluids are becoming a popular material in
the field of the semi-active control. However, the dynamic equation of
an MR mount is highly nonlinear and it is difficult to identify. FSMC
provides a simple method to achieve vibration attenuation of the
nonlinear system with uncertain disturbances. This method is capable
of handling the chattering problem of sliding mode control effectively
and the fuzzy control rules are obtained by using the Lyapunov
stability theory. The numerical simulations using one-dimension and
two-dimension FSMC show effectiveness of the proposed controller
for vibration suppression. Further, the well-known skyhook control
scheme and an adaptive sliding mode controller are also included in
the simulation for comparison with the proposed FSMC.
Abstract: The Beshar River is one of the most important aquatic ecosystems in the upstream of the Karun watershed in south of Iran which is affected by point and non point pollutant sources . This study was done in order to evaluate the effects of pollutants activities on the water quality of the Beshar river and its aquatic ecosystems. This river is approximately 190 km in length and situated at the geographical positions of 51° 20´ to 51° 48´ E and 30° 18´ to 30° 52´ N it is one of the most important aquatic ecosystems of Kohkiloye and Boyerahmad province in south-west Iran. In this research project, five study stations were selected to examine water pollution in the Beshar River systems. Human activity is now one of the most important factors affecting on hydrology and water quality of the Beshar river. Humans use large amounts of resources to sustain various standards of living, although measures of sustainability are highly variable depending on how sustainability is defined. The Beshar river ecosystems are particularly sensitive and vulnerable to human activities. Therefore, to determine the impact of human activities on the Beshar River, the most important water quality parameters such as pH, dissolve oxygen (DO), Biological Oxygen Demand (BOD5), Total Dissolve Solids (TDS), Nitrates (NO3-N) and Phosphates (PO4) were estimated at the five stations. As the results show, the most important pollution index parameters such as BOD5, NO3 and PO4 increase and DO and pH decrease according to human activities (P
Abstract: Nano fibers produced by electrospinning are of industrial and scientific attention due to their special characteristics such as long length, small diameter and high surface area. Applications of electrospun structures in nanotechnology are included tissue scaffolds, fibers for drug delivery, composite reinforcement, chemical sensing, enzyme immobilization, membrane-based filtration, protective clothing, catalysis, solar cells, electronic devices and others. Many polymer and ceramic precursor nano fibers have been successfully electrospun with diameters in the range from 1 nm to several microns. The process is complex so that fiber diameter is influenced by various material, design and operating parameters. The objective of this work is to apply genetic algorithm on the parameters of electrospinning which have the most significant effect on the nano fiber diameter to determine the optimum parameter values before doing experimental set up. Effective factors including initial polymer concentration, initial jet radius, electrical potential, relaxation time, initial elongation, viscosity and distance between nozzle and collector are considered to determine finest diameter which is selected by user.
Abstract: Realistic systems generally are systems with various
inputs and outputs also known as Multiple Input Multiple Output
(MIMO). Such systems usually prove to be complex and difficult to
model and control purposes. Therefore, decomposition was used to
separate individual inputs and outputs. A PID is assigned to each
individual pair to regulate desired settling time. Suitable parameters
of PIDs obtained from Genetic Algorithm (GA), using Mean of
Squared Error (MSE) objective function.